Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

English (EN)·Polski (PL)·Yкраїнський (UK)
Przejdź do strony domowej biblioteki Centralna Biblioteka Wojskowa Link otwiera się w nowym oknie Logo biblioteki Prolib Integro - strona głównaCentralna Biblioteka Wojskowa

Wyszukujesz frazę "Lee, S.-H." wg kryterium: Autor

  Lista filtrów
Wyrównaj
    Wyświetlanie 1-79 z 79
    Tytuł:
    Microstructure and Mechanical Properties of AA1050/ AA6061/AA1050 Multi-Layer Sheet Fabricated by Cold Roll Bonding Process
    Autorzy:
    Lee, S.-H.
    Powiązania:
    https://bibliotekanauki.pl/articles/353150.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    cold roll bonding process
    AA1050/AA6061/AA1050 complex sheet
    mechanical properties
    electron backscatter diffraction
    microstructure
    Opis:
    A cold roll-bonding process was applied to fabricate an AA1050/AA6061/AA1050 multi-layer sheet. Three Al sheets in which an AA6061 sheet is inserted inside two AA1050 sheets of 2 mm thickness, 40 mm width and 300 mm length were stacked up after surface treatment, and the material was then reduced to a thickness of 1.0 mm by multi-pass cold rolling. The AA1050/AA6061/AA1050 laminate complex sheet fabricated by roll bonding was then hardened by a natural aging (T4) and an artificial aging (T6) treatments. The microstructures of the as-roll bonded and the age-hardened Al complex sheets were revealed by optical microscope and electron back scatter diffraction analysis, and the mechanical properties were investigated by tensile and hardness testing. The strength of the as-roll bonded complex sheet was found to increase by 2.6 times, compared to that value of the starting material. Both AA1050 and AA6061 showed a typical recrystallization structure in which the grains were equiaxed after heat treatment. However, the grain size was smaller in AA6061 than in AA1050.
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 3; 1489-1492
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect Of Compaction Pressure And Sintering Temperature On The Liquid Phase Sintering Behavior Of Al-Cu-Zn Alloy
    Wpływ ciśnienia prasowania i temperatury spiekania na spiekanie stopu Al-Cu-Zn z udziałem fazy ciekłej
    Autorzy:
    Lee, S. H.
    Ahn, B.
    Powiązania:
    https://bibliotekanauki.pl/articles/351836.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    powder metallurgy
    liquid phase sintering
    compaction pressure
    Al-Cu-Zn alloy
    metalurgia proszków
    spiekanie w fazie ciekłej
    ciśnienie prasowania
    stop Al-Cu-Zn
    Opis:
    The liquid phase sintering characteristics of Al-Cu-Zn alloy were investigated with respect to various powder metallurgy processing conditions. Powders of each alloying elements were blended to form Al-6Cu-5Zn composition and compacted with pressures of 200, 400, and 600 MPa. The sintering process was performed at various temperatures of 410, 560, and 615°C in N2 gas atmosphere. Density and micro-Vickers hardness measurements were conducted at different processing stages, and transverse rupture strength of sintered materials was examined for each condition, respectively. The microstructure was characterized using optical microscope and scanning electron microscopy. The effect of Zn addition on the liquid phase sintering behavior during P/M process of the Al-Cu-Zn alloy was also discussed in detail.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1485-1489
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Fabrication And Mechanical Properties Of A Nanostructured Complex Aluminum Alloy By Three-Layer Stack Accumulative Roll-Bonding
    Wytwarzanie i właściwości mechaniczne nanostrukturalnego złożonego stopu aluminium wytworzonego przez walcowanie pakietowe trzech warstw
    Autorzy:
    Lee, S. H.
    Lee, S. R.
    Powiązania:
    https://bibliotekanauki.pl/articles/351499.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    accumulative roll-bonding (ARB)
    aluminum alloy
    microstructre
    mechanical properties
    akumulacyjne walcowanie pakietowe
    stop aluminium
    mikrostruktura
    właściwości mechaniczne
    Opis:
    A multi-layered complex aluminum alloy was successfully fabricated by three-layer stack accumulative roll bonding(ARB) process. The ARB using AA1050 and AA5052 alloy sheets was performed up to 7 cycles at ambient temperature without lubrication. The specimen processed by the ARB showed a multi-layer aluminum alloy sheet in which two aluminum alloys are alternately stacked. The grain size of the specimen decreased with the number of ARB cycles, became about 350nm in diameter after 7cycles. The tensile strength increased with the number of ARB cycles, after 6c it reached 281MPa which is about twice higher than that of the starting material. The microstructures and mechanical properties of a three-layer AA1050/AA5052 alloy fabricated by the ARB were compared to those of the conventional ARB-processed material.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1195-1198
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    The effect of patterns on image-based modelling of texture-less objects
    Autorzy:
    Hafeez, J.
    Jeon, H.-J.
    Hamacher, A.
    Kwon, S.-C.
    Lee, S.-H.
    Powiązania:
    https://bibliotekanauki.pl/articles/221814.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    structure-from-motion
    feature detection
    patterns analysis
    3D reconstruction
    surface comparison
    Opis:
    The task of generating fast and accurate three-dimensional (3D) models of objects or scenes through a sequence of non-calibrated images is an active field of research. The recent development in algorithm optimization has resulted in many automatic solutions that can provide an accurate 3D model from texture-full objects. Structure-from-motion (SfM) is an image-based method that uses discriminative point-based feature identifier, such as SIFT, to locate feature points in the images. This method faces difficulties when presented with the objects made of homogenous or texture-less surfaces. To reconstruct such surfaces a well-known technique is to apply an artificial variety by covering the surface with a random texture pattern prior to the image capturing process. In this work, we designed three series of image patterns which are tested based on the contrast and density ratio which increases from the first to the last pattern within the same series. The performance of the patterns is evaluated by reconstructing the surface of a texture-less object and comparing it with the true data. Using the best-found patterns from the experiments, a 3D model of a Moai statue is reconstructed. The experimental results demonstrate that the density and structure of a pattern highly affects the quality of the reconstruction.
    Źródło:
    Metrology and Measurement Systems; 2018, 25, 4; 755-767
    0860-8229
    Pojawia się w:
    Metrology and Measurement Systems
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Fabrication of Mo-Si-B Intermetallic Compound Powders Under Different Heat Treatment Conditions
    Autorzy:
    Park, J. H.
    Lee, S.
    Kim, D.
    Kim, Y.
    Yang, S. H.
    Lee, S. H.
    Powiązania:
    https://bibliotekanauki.pl/articles/353369.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Mo-Si-B alloys
    intermetallic compounds
    reitveld refinement
    T2 phase
    A15 phase
    Opis:
    In this research, we investigated the effects of reduction atmospheres on the creation of the Mo-Si-B intermetallic compounds (IMC) during the heat treatments. For outstanding anti-oxidation and elevated mechanical strength at the ultrahigh temperature, we fabricated the uniformly dispersed IMC powders such as Mo5SiB2 (T2) and Mo3Si (A15) phases using the two steps of chemical reactions. Especially, in the second procedure, we studied the influence of the atmospheres (e.g. vacuum, argon, and hydrogen) on the synthesis of IMCs during the reduction. Furthermore, the newly produced IMCs were observed by SEM, XRD, and EDS to identify the phase of the compounds. We also calculated an amount of IMCs in the reduced powders depending on the atmosphere using the Reitveld refinement method. Consequently, it is found that hydrogen atmosphere was suitable for fabrication of IMC without other IMC phases.
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 3; 1509-1512
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Characteristics Of The Porous Body Sintered By Nano-Sized Fe-Cr-Al Alloy Powder
    Charakterystyka porowatego korpusu spiekanego z nanometrycznego proszku stopu Fe-Cr-Al
    Autorzy:
    Lee, S.-I.
    Lee, S.-H.
    Gu, B.-U.
    Lee, D.-W.
    Kim, B.-K.
    Powiązania:
    https://bibliotekanauki.pl/articles/356635.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Fe-Cr-Al powder
    metallic sponges
    sintering temperature
    oxidation resistance
    proszek Fe-Cr-Al
    proszek nanometryczny
    temperatura spiekania
    odporność na utlenianie
    Opis:
    Porous metal with uniform honeycomb structure was successfully produced by sintering using Fe-Cr-Al nano powder, which was prepared by the pulsed wire evaporation (PWE) in ethanol. Its process consisted of the several steps; 1) coating on the surface of polyurethane sponge with the liquid droplets generated from the ethanol-based slurry where the Fe-Cr-Al nano powders were uniformly dispersed, 2) heat treatment of debinding to remove the polyurethane sponge and 3) sintering of the porous green body formed by Fe-Cr-Al nano powders. The strut thickness of porous Fe-Cr-Al was increased by the increase of spraying times in ESP step. Also, The shrinkages and the oxidation resistance of the sintered porous body was increased with increase of sintering temperature. The optimal sintering temperature was shown to 1450°C in views to maximize the oxidation resistance and sinterability.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1275-1279
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Fabrication and Characterization of CoCrFeNiMn High Entropy Alloy Powder Processed by Gas Atomization
    Autorzy:
    Park, T. G.
    Lee, S. H.
    Lee, B.
    Cho, H. M.
    Choi, W. J.
    Kim, B. S.
    Shin, K. S.
    Kim, T.-S.
    Powiązania:
    https://bibliotekanauki.pl/articles/353649.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    high entropy alloy
    gas atomization
    spark plasma sintering
    CoCrFeNiMn
    Opis:
    In this study, precisely controlled large scale gas atomization process was applied to produce spherical and uniform shaped high entropy alloy powder. The gas atomization process was carried out to fabricate CoCrFeNiMn alloy, which was studied for high ductility and mechanical properties at low temperatures. It was confirmed that the mass scale, single phase, equiatomic, and high purity spherical high entropy alloy powder was produced by gas atomization process. The powder was sintered by spark plasma sintering process with various sintering conditions, and mechanical properties were characterized. Through this research, we have developed a mass production process of high quality and spherical high entropy alloy powder, and it is expected to expand applications of this high entropy alloy into fields such as powder injection molding and 3D printing for complex shaped components.
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 2; 1055-1059
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Economic statistical design of variable sampling interval X̅ control chart based on surrogate variable using genetic algorithms
    Autorzy:
    Lee, T.-H.
    Hong, S.-H.
    Kwon, H.-M.
    Lee, M.
    Powiązania:
    https://bibliotekanauki.pl/articles/406970.pdf
    Data publikacji:
    2016
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    economic design
    surrogate variable
    variable sampling interval
    TRISO Fuel
    genetic algorithms
    Opis:
    In many cases, a X̅ control chart based on a performance variable is used in industrial fields. Typically, the control chart monitors the measurements of a performance variable itself. However, if the performance variable is too costly or impossible to measure, and a less expensive surrogate variable is available, the process may be more efficiently controlled using surrogate variables. In this paper, we present a model for the economic statistical design of a VSI (Variable Sampling Interval) X̅ control chart using a surrogate variable that is linearly correlated with the performance variable. We derive the total average profit model from an economic viewpoint and apply the model to a Very High Temperature Reactor (VHTR) nuclear fuel measurement system and derive the optimal result using genetic algorithms. Compared with the control chart based on a performance variable, the proposed model gives a larger expected net income per unit of time in the long-run if the correlation between the performance variable and the surrogate variable is relatively high. The proposed model was confined to the sample mean control chart under the assumption that a single assignable cause occurs according to the Poisson process. However, the model may also be extended to other types of control charts using a single or multiple assignable cause assumptions such as VSS (Variable Sample Size) X̅ control chart, EWMA, CUSUM charts and so on.
    Źródło:
    Management and Production Engineering Review; 2016, 7, 4; 54-64
    2080-8208
    2082-1344
    Pojawia się w:
    Management and Production Engineering Review
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Implementation of a Novel Audio Network Protocol
    Autorzy:
    Lee, J.
    Jeon, H.
    Choi, P.
    Kwon, S.
    Lee, S.
    Powiązania:
    https://bibliotekanauki.pl/articles/178062.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    audio mixer
    AoIP
    audio over internet protocol
    DANTE
    SR System
    Opis:
    Recently, the rapid advancement of the IT industry has resulted in significant changes in audio-system configurations; particularly, the audio over internet protocol (AoIP) network-based audio-transmission technology has received favourable evaluations in this field. Applying the AoIP in a certain section of the multiple-cable zone is advantageous because the installation cost is lower than that for the existing systems, and the original sound is transmitted without any distortion. The existing AoIP-based technology, however, cannot control the audio-signal characteristics of every device and can only transmit multiple audio signals through a network. In this paper, the proposed Audio Network & Control Hierarchy Over peer-to-peer (Anchor) system enables all audio equipment to send and receive signals via a data network, and the receiving device can mix the signals of different IPs. Accordingly, it was possible to improve the system-application flexibility by simplifying the audio-system configuration. The research results confirmed that the received audio signals from different IPs were received, mixed, and output without errors. It is expected that Anchor will become a standard for audio-network protocols.
    Źródło:
    Archives of Acoustics; 2018, 43, 4; 637-645
    0137-5075
    Pojawia się w:
    Archives of Acoustics
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Immobilization of rambutan (Nephelium lappaceum) peel as a sorbent for Basic Fuchsin removal
    Autorzy:
    Lee, H.-J.
    Ong, S.-T.
    Powiązania:
    https://bibliotekanauki.pl/articles/207651.pdf
    Data publikacji:
    2017
    Wydawca:
    Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
    Tematy:
    fuchsin
    Fourier transform infrared spectrophotometry
    FTIR
    Nephelium lappaceum
    fuksyna
    spektroskopia w podczerwieni z transformatą Fouriera
    Opis:
    The potential of rambutan (Nephelium lappaceum) peel as a low-cost adsorbent in an immobilized condition to remove Basic Fuchsin from aqueous solution was studied. The effect of initial dye concentration, contact time, pH and adsorbent dosage for the dye removal was studied at room temperature (26±2 °C). Infrared spectrum of rambutan peel indicates the presence of C–O, –OH and C=C functional groups. The adsorption rate was found to be high at the first 30 min and the process reached equilibrium after 3 h with more than 80% of dye being removed. The uptake of Basic Fuchsin was more promising at pH slightly above 7. The study of sorption model and kinetic model showed that the adsorption of Basic Fuchsin on rambutan peel conformed to the Freundlich isotherm and pseudo-second order kinetics with a high correlation coefficient, R,sup>2 > 0.98. This indicates the Basic Fuchsin adsorbs chemically on the heterogeneous surface of rambutan peel. The maximum adsorption capacity determined from the Langmuir isotherm was 108.696 mg/g. It seems that rambutan peel has the potential to substitute activated carbon as an alternative low-cost adsorbent in the treatment of the dye effluent.
    Źródło:
    Environment Protection Engineering; 2017, 43, 1; 169-181
    0324-8828
    Pojawia się w:
    Environment Protection Engineering
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Analysis of Working Postures at a Construction Site Using the OWAS Method
    Autorzy:
    Lee, T. H.
    Han, C. S.
    Powiązania:
    https://bibliotekanauki.pl/articles/90807.pdf
    Data publikacji:
    2013
    Wydawca:
    Centralny Instytut Ochrony Pracy
    Tematy:
    construction
    posture
    occupational injury
    OWAS
    budownictwo
    pozycja przy pracy
    analiza bezpieczeństwa
    Opis:
    This study used OWAS to analyze the working postures of construction workers on building the foundations of a log cabin. Three construction workers, with an average work experience of 40 years, participated in this study. Eight elementary jobs of building the foundations of a log cabin were videotaped at a construction site and analyzed later in the laboratory. For an overall distribution of trunk postures, OWAS identified that a bent and twisted trunk posture (34%), which fell into action category 3, was the major poor posture for construction workers. This study also identified that tying beams with steel bars, assembling column templates, and cement grouting of the ground were the 3 principal jobs in which workers building the foundations exhibited poor working posture. This article suggests ways to reduce and evaluate poor posture in a dynamic construction site.
    Źródło:
    International Journal of Occupational Safety and Ergonomics; 2013, 19, 2; 245-250
    1080-3548
    Pojawia się w:
    International Journal of Occupational Safety and Ergonomics
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effects of Hand Posture, Breathing Type, Arm Posture and Body Posture on Hand Errors
    Autorzy:
    Lee, T. H.
    Cheng, T. S.
    Powiązania:
    https://bibliotekanauki.pl/articles/90970.pdf
    Data publikacji:
    2012
    Wydawca:
    Centralny Instytut Ochrony Pracy
    Tematy:
    aiming
    fine manipulation
    hand tremor
    pointing
    Opis:
    This study consisted of 2 experiments. Experiment 1 examined the effects of hand posture, arm posture and body posture on hand error, while experiment 2 examined the effects of hand posture, breathing type and body posture on hand error. This study showed that more hand errors occurred in the nondominant hand, extended arm, normal breathing and standing compared with errors in the dominant hand, flexed arm, inspire–hold and sitting, respectively. This study advised people to use their dominant hand, flex their arm, inspire and hold the breath and support their body while performing fine manipulation tasks. Finally, hand error varied dramatically across the participants, indicating the need to screen individuals for fine manual manipulation tasks.
    Źródło:
    International Journal of Occupational Safety and Ergonomics; 2012, 18, 3; 393-398
    1080-3548
    Pojawia się w:
    International Journal of Occupational Safety and Ergonomics
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Asymmetric Lifting Capabilities for Different Container Dimensions
    Autorzy:
    Lee, T. H.
    Cheng, T. S.
    Powiązania:
    https://bibliotekanauki.pl/articles/91162.pdf
    Data publikacji:
    2011
    Wydawca:
    Centralny Instytut Ochrony Pracy
    Tematy:
    lifting capacity
    asymmetric lifting
    container
    Opis:
    This study recruited 14 young male participants to examine human 4-h maximum acceptable weight of lifting (MAWL) and maximum weight of lifting (MWL) for different modes of asymmetric lifting and containers. The results showed that asymmetric lifting with trunk rotation decreased MAWL and MWL by 9.1 and 17.3%, respectively, and asymmetric lifting with body turn decreased MAWL and MWL by 6.1%, when compared with the symmetric lifting. The decreasing effects of container width and MAWL and MWL were greater than those of container length. Participants selected MAWL of ~33–37% of their MWL capability.
    Źródło:
    International Journal of Occupational Safety and Ergonomics; 2011, 17, 2; 187-193
    1080-3548
    Pojawia się w:
    International Journal of Occupational Safety and Ergonomics
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Fabrication of Porous Silica Fibers by Electrospinning for Sound Absorbing Materials
    Autorzy:
    Cho, Y.-S.
    Lee, H. J.
    Powiązania:
    https://bibliotekanauki.pl/articles/353561.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    electrospinning
    porous silica fiber
    thermal insulator
    sound absorption
    Opis:
    Macroporous silica fibers having spherical cavities were fabricated by electrospinning using the spinning solution prepared from the mixed dispersion of tetraethylorthosilicate (TEOS) and polystyrene nanospheres as precursor and sacrificial templates, respectively, by injection through metallic nozzle. By applying electric field, the electro-spun fibers obtained by evaporation-driven self-assembly were collected on flat substrate or rotating drum, followed by the removal of the templates by calcination. The sound absorption coefficient of the porous fibers was measured by impedance tube, and the measured value was larger than 0.9 at high frequency region of incident waves. The surface of the resulting fibers was modified using fluorine-containing silane coupling agent to produce superhydrophobic fibrous materials to prevent the infiltration of humidity.
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 3; 1497-1502
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Morphology Change Of Si Deposit In Molten Salt Electrorefining
    Zmiana morfologii osadu Si podczas elektrorafinacji w stopionych solach
    Autorzy:
    Ryu, H. Y.
    Kwon, S. C.
    Han, M. H.
    An, Y. S.
    Lee, J. S.
    Lee, J. H.
    Powiązania:
    https://bibliotekanauki.pl/articles/354346.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    molten salt
    silicon
    morphology
    electrorefining
    current density
    sól stopiona
    krzem
    morfologia
    elektrorafinacja
    gęstość prądu
    Opis:
    The effects of processing parameters on the morphology change in a Si deposit recovered by means of molten salt electrorefining are evaluated using electrochemical techniques such as cyclic voltammetry and chronopotentiometry at 800°C. It was found that concentration of K2SiF6 and current density were important parameters in determining deposit size. Higher concentrations of K2SiF6 were effective in coarsening the silicon deposit and decreasing the cell potential. Silicon nanofiber was recovered at 5 wt% of K2SiF6 whereas dense particles were prepared at 30 and 50 wt% of K2SiF6. The morphology of the Si deposit was determined by the concentration of Si in the electrolyte which is related to the formation of crystal and growth of Si. The formation mechanism of the Si deposit was interpreted by using high resolution TEM as well as electrochemical properties.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1491-1497
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Contamination of soil with heavy metals drained out from abandoned mines in the South-West region of Korea
    Autorzy:
    Kim, S.-D.
    Dho, H.-S.
    Lee, S.-J.
    Powiązania:
    https://bibliotekanauki.pl/articles/207493.pdf
    Data publikacji:
    2015
    Wydawca:
    Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
    Tematy:
    soil pollution
    abandoned mines
    arsenic
    heavy metals
    nickel
    soils
    zinc
    contamination level
    forest regions
    surface soil
    zanieczyszczenie gleby
    zlikwidowane kopalnie
    arsen
    metale ciężkie
    nikiel
    gleby
    cynk
    poziom zanieczyszczeń
    obszary leśne
    powierzchniowe warstwy gleby
    Opis:
    Contamination of soil with heavy metals drained out from twenty eight abandoned mines in the southwest regions of Korea has been investigated. Utilizing various statistical techniques, the goal was to evaluate and analyze pH and the contamination with Arsenic, and the following six heavy metals: cadmium, hydrargyrum, lead, nickel, chromium, and zinc. Contamination levels of heavy metals were determined depending on the depth of the soil. Results indicated that the subsoil and the surface soil both were strongly contaminated with lead and arsenic. Furthermore, the subsoil also contained much nickel. In forest regions, high levels of lead and arsenic, whereas in all regions high levels of zinc have been detected.
    Źródło:
    Environment Protection Engineering; 2015, 41, 3; 61-72
    0324-8828
    Pojawia się w:
    Environment Protection Engineering
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Safety Management in a Relationship-Oriented Culture
    Autorzy:
    Hsu, S. H.
    Lee, C. C.
    Powiązania:
    https://bibliotekanauki.pl/articles/91057.pdf
    Data publikacji:
    2012
    Wydawca:
    Centralny Instytut Ochrony Pracy
    Tematy:
    safety management
    safety climate
    relationship-oriented culture
    high-risk industry
    safety culture
    Opis:
    A relationship-oriented culture predominates in the Greater China region, where it is more important than in Western countries. Some characteristics of this culture influence strongly the organizational structure and interactions among members in an organization. This study aimed to explore the possible influence of relationships on safety management in relationship-oriented cultures. We hypothesized that organizational factors (management involvement and harmonious relationships) within a relationship-oriented culture would influence supervisory work (ongoing monitoring and task instructions), the reporting system (selective reporting), and teamwork (team communication and co-ordination) in safety management at a group level, which would in turn influence individual reliance complacency, risk awareness, and practices. We distributed a safety climate questionnaire to the employees of Taiwanese high-risk industries. The results of structural equation modeling supported the hypothesis. This article also discusses the findings and implications for safety improvement in countries with a relationship-oriented culture.
    Źródło:
    International Journal of Occupational Safety and Ergonomics; 2012, 18, 1; 35-45
    1080-3548
    Pojawia się w:
    International Journal of Occupational Safety and Ergonomics
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Boundary element modelling of wave diffraction by interaction with wave-offshore structure and dredged region
    Autorzy:
    Kim, S. D.
    Lee, H. J.
    Powiązania:
    https://bibliotekanauki.pl/articles/259525.pdf
    Data publikacji:
    2010
    Wydawca:
    Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
    Tematy:
    Submarine pit
    Green function
    boundary integral approach
    breakwater
    Opis:
    The purpose of this study is to estimate the wave height at the front face of breakwater (Refracted breakwater and Straight breakwater), when dredging like the submarine pit is performed in the distant offshore from outer breakwater. The wave field of the problem is considered to be two dimensional planes and the configuration of the pit region is designated by a single horizontal long-rectangular system. The numerical approach uses the Green function based on the boundary integral approach. The results of the present numerical works are illustrated by applying the normal and inclined incidence. It is shown that in the case of normal incidence, the ratio of wave height reduction at the front face of both types of breakwaters is approximately more than 20% due to the effect of the submarine pit on the sea bed. Furthermore, regardless of the type of breakwater and the difference in incident wave angles, the ratio of wave height was shown to be reduced.
    Źródło:
    Polish Maritime Research; 2010, 2; 67-71
    1233-2585
    Pojawia się w:
    Polish Maritime Research
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Microstructure and Magnetic Properties of NdFeB Sintered Magnets Diffusion-Treated with Cu/Al Mixed Dyco Alloy-Powder
    Autorzy:
    Lee, M.-W.
    Bae, K.-H.
    Lee, S.-R.
    Kim, H.-J.
    Jang, T.-S.
    Powiązania:
    https://bibliotekanauki.pl/articles/353351.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Nd-Fe-B sintered magnets
    grain boundary diffusion process
    low melting point element
    DyCo alloy-powder diffusion
    Opis:
    We investigated the microstructural and magnetic property changes of DyCo, Cu + DyCo, and Al + DyCo diffusion-treated NdFeB sintered magnets. The coercivity of all diffusion treated magnet was increased at 880ºC of 1st post annealing(PA), by 6.1 kOe in Cu and 7.0 kOe in Al mixed DyCo coated magnets, whereas this increment was found to be relatively low (3.9 kOe) in the magnet coated with DyCo only. The diffusivity and diffusion depth of Dy were increased in those magnets which were treated with Cu or Al mixed DyCo, mainly due to comparatively easy diffusion path provided by Cu and Al because of their solubility with Ndrich grain boundary phase. The formation of Cu/Al-rich grain boundary phase might have enhanced the diffusivity of Dy-atoms. Moreover, relatively a large number of Dy atoms reached into the magnet and mostly segregated at the interface of Nd2 Fe14 B and grain boundary phases covering Nd2 Fe14 B grains so that the core-shell type structures were developed. The formation of highly anisotropic (Nd, Dy)2Fe14B phase layer, which acted as the shell in the core-shell type structure so as to prevent the reverse domain movement, was the cause of enhancing the coercivity of diffusion treated NdFeB magnets. Segregation of cobalt in Nd-rich TJP followed by the formation of Co-rich phase was beneficial for the coercivity enhancement, resulting in the stabilization of the metastable c-Nd2O3 phase.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1263-1266
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Enhancement of Life Time of the Dimensionally Stable Anode for Copper Electroplating Applications
    Autorzy:
    Son, S. H.
    Park, S. C.
    Lee, M. S.
    Powiązania:
    https://bibliotekanauki.pl/articles/356684.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    dimensionally stable anode
    surface treatment
    life time
    copper
    electrodeposition
    Opis:
    In order to enhance the long-term stability of DSA for copper electroplating process, in the present study, noble metal oxides with excellent electrochemical properties was used and optimum condition was determined the ratio of noble metal oxides, surface pre-treatment of titanium substrate and heat treatment. The effect of the surface pretreatment of titanium substrate and ratio of noble metal oxides were estimated by accelerated test at the highly current density conditions. The lifetime of DSA increase six-fold higher as the oxide thickness of Ta 7 : Ir 3 composition ratio. Under the optimal condition, surface pretreatment led to dramatic increase in the lifetime of DSA.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1019-1022
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Optimization of the service strategy in a queueing system with energy harvesting and customers’ impatience
    Autorzy:
    Dudin, A.
    Lee, M. H.
    Dudin, S.
    Powiązania:
    https://bibliotekanauki.pl/articles/331226.pdf
    Data publikacji:
    2016
    Wydawca:
    Uniwersytet Zielonogórski. Oficyna Wydawnicza
    Tematy:
    energy harvesting
    threshold strategy
    optimization
    Markovian arrival process
    uzyskiwanie energii
    optymalizacja
    Markowski proces zgłoszeń
    Opis:
    A single-server queueing system with an infinite buffer is considered. The service of a customer is possible only in the presence of at least one unit of energy, and during the service the number of available units decreases by one. New units of energy arrive in the system at random instants of time if the finite buffer for maintenance of energy is not full. Customers are impatient and leave the system without service after a random amount of waiting time. Such a queueing system describes, e.g., the operation of a sensor node which harvests energy necessary for information transmission from the environment. Aiming to minimize the loss of customers due to their impatience (and maximize the throughput of the system), a new strategy of control by providing service is proposed. This strategy suggests that service temporarily stops if the number of customers or units of energy in the system becomes zero. The server is switched off (is in sleep mode) for some time. This time finishes (the server wakes up) if both the number of customers in the buffer and the number of energy units reach some fixed threshold values or when the number of energy units reaches some threshold value and there are customers in the buffer. Arrival flows of customers and energy units are assumed to be described by an independent Markovian arrival process. The service time has a phase-type distribution. The system behavior is described by a multi-dimensional Markov chain. The generator of this Markov chain is derived. The ergodicity condition is presented. Expressions for key performance measures are given. Numerical results illustrating the dependence of a customer’s loss probability on the thresholds defining the discipline of waking up the server are provided. The importance of the account of correlation in arrival processes is numerically illustrated.
    Źródło:
    International Journal of Applied Mathematics and Computer Science; 2016, 26, 2; 367-378
    1641-876X
    2083-8492
    Pojawia się w:
    International Journal of Applied Mathematics and Computer Science
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Fabrication Of Zn4Sb3 Alloys By A Combination Of Gas-Atomization And Spark Plasma Sintering Processes
    Wytwarzanie i konsolidacja proszków stopowych zn4sb3 przez kombinację procesów atomizacji gazowej i spiekania
    Autorzy:
    Dharmaiah, P.
    Kim, H.-S.
    Lee, L. H.
    Hong, S.-J.
    Powiązania:
    https://bibliotekanauki.pl/articles/355894.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    gas atomization
    microstructure
    spark plasma sintering (SPS)
    X-ray diffraction
    atomizacja gazowa
    mikrostruktura
    SPS
    spiekanie plazmowe
    analiza rentgenowska (XRD)
    Opis:
    In this study, single phase polycrystalline Zn4Sb3 as well as 11 at.% Zn-rich Zn4Sb3 alloy having ε-Zn4Sb3 (majority phase) and Zn (minority phase) phases bulk samples produced by gas-atomization and subsequently consolidated by spark plasma sintering (SPS) process. The crystal structures were analyzed by X-ray diffraction (XRD) and cross-sectional microstructure were observed by the scanning electron microscopy (SEM). The internal grain microstructure of 11at.% Zn-rich Zn4Sb3 powders shows lamellar structure. Relative density, Vickers hardness and crack lengths were measured to investigate the effect of sintering temperature of Zn4Sb3 samples which are sintered at 653, 673 and 693 K. Relative density of the single phase bulk Zn4Sb3 sample reached to 99.2% of its theoretical density. The micro Vickers hardness of three different sintering temperatures were found around 2.17 – 2.236 GPa.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1417-1421
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Aluminum Oxide Formation On Fecral Catalyst Support By Electro-Chemical Coating
    Powstawanie tlenku glinu na nośniku katalizatora FeCrAl przez osadzanie elektrochemiczne
    Autorzy:
    Yang, H. S.
    Jang, D. H.
    Lee, K. J.
    Powiązania:
    https://bibliotekanauki.pl/articles/355942.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    FeCrAl
    catalyst support
    aluminum oxide formation
    PEO
    plasma electrolytic oxidation
    electrochemical coating
    nośnik katalizatora
    tlenek glinu
    plazmowe utlenianie elektrolityczne
    elektrochemiczne osadzanie
    Opis:
    FeCrAl is comprised essentially of Fe, Cr, Al and generally considered as metallic substrates for catalyst support because of its advantage in the high-temperature corrosion resistance, high mechanical strength, and ductility. Oxidation film and its adhesion on FeCrAl surface with aluminum are important for catalyst life. Therefore various appropriate surface treatments such as thermal oxidation, Sol, PVD, CVD has studied. In this research, PEO (plasma electrolytic oxidation) process was applied to form the aluminum oxide on FeCrAl surface, and the formed oxide particle according to process conditions such as electric energy and oxidation time were investigated. Microstructure and aluminum oxide particle on FeCrAl surface after PEO process was observed by FE-SEM and EDS with element mapping analysis. The study presents possibility of aluminum oxide formation by electro-chemical coating process without any pretreatment of FeCrAl.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1503-1506
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Characterization of Cu and Ni Nano-Fluids Synthesized by Pulsed Wire Evaporation Method
    Autorzy:
    Kim, H.-S.
    Yilmaz, F.
    Dharmaiah, P.
    Lee, D.-J
    Lee, T.-H.
    Hong, S.-J.
    Powiązania:
    https://bibliotekanauki.pl/articles/356475.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    pulsed wire evaporation
    nanofluid
    Cu
    Ni
    suspension stability
    dispersibility
    Opis:
    In the present work, Cu and Ni nanofluids were synthesized using the pulsed wire evaporation (PWE) method in the different aqueous medias, namely (ethanol and ethylene glycol), and the effects of the aqueous media on the dispersion state, stability, and particle size of nanoparticles were studied. The size and morphology of synthesized nano-particles were investigated by transmission electron microscopy (TEM). Also, the dispersion stability of the nanofluids was evaluated by turbiscan analysis. The TEM results showed that the nano-particles were spherical in shape, and the average particle size was below 100 nm. The average particle size of the Cu nano-particles was smaller than that of Ni, which was attributed to a difference in the specific sublimation energy of the elements. Moreover, ethylene glycol (EG) exhibited higher suspension stability than ethanol. Finally, the dispersion stability of Cu@EG displayed the highest value due to lower particle size and greater viscosity.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 999-1004
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effects of acute lipopolysaccharide-induced toxemia model on some neglected blood parameters
    Autorzy:
    Adam, G.O.
    Lee, H.R.
    Lee, S.J.
    Kim, S.J.
    Kim, G.B.
    Kang, H.S.
    Powiązania:
    https://bibliotekanauki.pl/articles/2087627.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Toxemia
    lipopolysaccharide
    base excess
    pH
    animal model
    Źródło:
    Polish Journal of Veterinary Sciences; 2018, 21, 4; 665-671
    1505-1773
    Pojawia się w:
    Polish Journal of Veterinary Sciences
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect of phytogenics on growth performance, fecal score, blood profiles, fecal noxious gas emission, digestibility, and intestinal morphology of weanling pigs challenged with Escherichia coli K88
    Autorzy:
    Mohana Devi, S.
    Lee, S.I.
    Kim, L.H.
    Powiązania:
    https://bibliotekanauki.pl/articles/30946.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Opis:
    Phytogenic feed additives have become attractive alternatives for use in animal diets. The objective of the present study was to evaluate the effect of a phytogenic-based feed additive on growth performance, nutrient digestibility, blood profiles, fecal noxious gas emission, and intestinal morphology of weaning pigs after dietary challenge with E. coli K88. A total of 120 crossbred pigs [(Yorkshire × Landrace) × Duroc)] with an initial body weight (BW) of 6.09 ± 0.96 kg (21 d of age) were assigned randomly to 1 of the 4 dietary treatments. Each pen housed 5 pigs, and there were 6 pens/treatment. Treatments included: T1, negative control (without antibiotics); T2, T1 + antibiotic; T3, T1 + 0.05% phytogenics; and T4, T1 + 0.2% commercial mix of organic acids. Overall, the average daily gain (ADG) with the T3 treatment was higher (P<0.05). At wk 1, the apparent total tract digestibility (ATTD) of dry matter (DM) was increased (P<0.05) with T4 treatment. The ATTD of ash with T3 and T4 treatments was greater (P<0.05). At wk 3, pigs fed with the T4 diet had a significantly higher (P<0.05) ATTD of DM. The ATTD of ash and calcium (Ca) was significantly increased (P<0.05) with the T4 treatment. Pigs fed with the T3 diet had a higher (P<0.05) ATTD of phosphorus (P). At wk 6, the ATTD of ash was significantly increased (P<0.05) with the T1 and T3 treatments. The data indicate that phytogenics positively affect growth performance of weaning pigs, indicating that their use as an alternative in the diets of weaning pigs can significantly improve ADG, under challenge with E.coli K88.
    Źródło:
    Polish Journal of Veterinary Sciences; 2015, 18, 3
    1505-1773
    Pojawia się w:
    Polish Journal of Veterinary Sciences
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect Of Heat-Treatment On Microstructure And Magnetic Properties Of Nanocrystallized Mn-Zn Ferrite Powders
    Wpływ obróbki cieplnej na mikrostrukturę i właściwości magnetyczne nanokrystalicznych proszków ferrytu Mn-Zn
    Autorzy:
    Lee, W. H.
    Hong, C. S.
    Chang, S. Y.
    Powiązania:
    https://bibliotekanauki.pl/articles/351552.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    high energy ball milling
    nanosized particles
    crystallite size
    magnetic properties
    frezowanie kulowe
    nanocząstki
    wielkości krystalitów
    właściwości magnetyczne
    Opis:
    The initial ferrite powders were subjected to high energy ball milling at 300rpm for 3h, and subsequently heat-treated at 573-1273K for 1h. Based on the observation of microstructure and measurement of magnetic properties, the heat-treatment effect was investigated. The size of initial powders was approximately 70μm. After milling, the powders with approximately 230nm in size were obtained, which were composed of the nano-sized particles of approximately 15nm in size. The milled powders became larger to approximately 550nm after heat-treatment at 973K. In addition, the size of particles increased to approximately 120nm with increasing temperature up to 973K. The coercivity of initial powders was almost unchanged after milling, whereas the saturation magnetization increased. As the heat-treatment temperature increased, the saturation magnetization gradually increased and the maximum coercivity was obtained at 773K.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1347-1350
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Recovery of HCL from chloride leach solution of spent HDS catalyst by solvent extraction
    Autorzy:
    Banda, R.
    Nguyen, T.H.
    Lee, M.S.
    Powiązania:
    https://bibliotekanauki.pl/articles/185588.pdf
    Data publikacji:
    2013
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    HCl
    extraction
    stripping
    recovery
    TEHA
    wydobycie
    Opis:
    In the present work, amine based extractant and its mixture with cationic and solvating extractants were tested for the extraction of HCl from chloride solution containing Al(III). The chloride feed solution resulted from the leaching of spent HDS (hydro-desulfurization) catalysts. For this purpose, amine extractants, such as TOA (trioctyl amine), Alamine 336 (a mixture of tri-octyl/decyl amine), Alamine 308 (tri-isooctyl amine), and TEHA (tri 2-ethylhexyl amine) were used and the extraction and stripping behavior of HCl was compared. The extracted HCl was easily stripped from loaded TEHA phase, when compared with the other tested tertiary amine system. Solvent extraction reaction of HCl by TEHA was determined from the extraction data. Unlike TOA and Alamine 336, adding cationic extractant to TEHA had negligible effect on the extraction and stripping of HCl. In our experimental ranges, no Al was extracted by amines and pure HCl was recovered. MaCabe-Thiele diagrams for the extraction and stripping of HCl by TEHA were constructed.
    Źródło:
    Chemical and Process Engineering; 2013, 34, 1; 153-163
    0208-6425
    2300-1925
    Pojawia się w:
    Chemical and Process Engineering
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Self-Consolidation and Surface Modification of Mechanical Alloyed Ti-25.0 at.% Al Powder Mixture by Using an Electro-Discharge Technique
    Autorzy:
    Chang, S. Y.
    Jang, H. S.
    Yoon, Y. H.
    Kim, Y. H.
    Kim, J. Y.
    Lee, Y. K.
    Lee, W. H.
    Powiązania:
    https://bibliotekanauki.pl/articles/354212.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    sintering
    mechanical alloying
    powder consolidation
    intermetallic compounds
    titanium aluminides
    Opis:
    Electrical discharges using a capacitance of 450 μF at 0.5, 1.0, and 1.5 kJ input energies were applied in a N2 atmosphere to obtain the mechanical alloyed Ti3Al powder without applying any external pressure. A solid bulk of nanostructured Ti3Al was obtained as short as 160 μsec by the Electrical discharge. At the same time, the surface has been modified into the form of Ti and Al nitrides due to the diffusion process of nitrogen to the surface. The input energy was found to be the most important parameter to affect the formation of a solid core and surface chemistry of the compact.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1293-1297
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect Of DyMn Alloy-Powder Addition On Microstructure And Magnetic Properties Of NdFeB Sintered Magnets
    Wpływ dodatku proszku DyMn na mikrostrukturę i właściwości magnetyczne spiekanych magnesów NdFeB
    Autorzy:
    Lee, M.-W.
    Dhakal, D. R.
    Kim, T. H.
    Lee, S. R.
    Kim, H. J.
    Jang, T. S.
    Powiązania:
    https://bibliotekanauki.pl/articles/357010.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Nd-Fe-B sintered magnets
    DyMn-alloy powder
    coercivity
    low melting point element
    magnesy spiekane
    proszek DyMn
    koercja
    elementy o niskiej temperaturze topnienia
    Opis:
    Micostructural change and corresponding effect on coercivity of a NdFeB sintered magnet mixed with small amount of DyMn powder was investigated. In the sintered magnet mixed with the DyMn alloy-powder Dy-rich shell was formed at outer layer of the main grains, while Mn was mostly concentrated at Nd-rich triple junction phase (TJP), lowering melting temperature of the Nd-rich phase that eventually improved the microstructural characteristics of the gain boundary phase. The coercivity of a magnet increased more than 3.5 kOe by the mixing of the DyMn alloy-powder.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1407-1409
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Spontaneous Formation of Titanium Nitride on the Surface of a Ti Rod Induced by Electro-Discharge-Heat-Treatment in an N2 Atmosphere
    Autorzy:
    Lee, W. H.
    Yoon, Y. H.
    Kim, Y. H.
    Lee, Y. K.
    Kim, J. Y.
    Chang, S. Y.
    Powiązania:
    https://bibliotekanauki.pl/articles/352477.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    titanium
    surface modification
    diffusion
    heat treatment
    XPS
    Opis:
    A single pulse of 2.0 to 3.5 kJ of input energy from a 450 mF capacitor was applied to a commercially pure Ti rod in a N2 atmosphere. The surface of the Ti rod transformed from TiO2 into titanium nitride in times as short as 159 msec, providing a bimodal morphology of the cross-section. A much higher value of hardness that was observed at the edge of the cross-section was attributed to nitrogen-induced solid-solution hardening that occurred during the electrical discharge process. The activation energy (Ea) for the diffusion process was estimated to be approximately 86.9 kJ/mol. Results show that the electrical discharge process is a possible potential method for the nitriding of Ti; advantages include a short processing time and control of the nitrided layer without dimensional changes.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1281-1285
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    CO Oxidation Properties Of Selective Dissoluted Metallic Glass Composites
    Utlenianie wybranych rozcieńczonych kompozytów szkieł metalicznych
    Autorzy:
    Kim, S. Y.
    Lee, M. H.
    Kim, T. S.
    Kim, B. S.
    Powiązania:
    https://bibliotekanauki.pl/articles/355092.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    CO oxidation
    metallic glasses
    porous metal
    catalyst materials
    utlenianie
    szkło metaliczne
    metale porowate
    materiał katalityczny
    Opis:
    Porous metallic materials have been widely used in many fields including aerospace, atomic energy, electro chemistry and environmental protection. Their unique structures make them very useful as lightweight structural materials, fluid filters, porous electrodes and catalyst supports. In this study, we fabricated Ni-based porous metallic glasses having uniformly dispersed micro meter pores by the sequential processes of ball-milling and chemical dissolution method. We investigated the application of our porous metal supported for Pt catalyst. The oxidation test was performed in an atmosphere of 1% CO and 3% O2. Microstructure observation was performed by using a scanning electron microscope. Oxidation properties and BET (Brunauer, Emmett, and Teller) were analyzed to understand porous structure developments. The results indicated that CO Oxidation reaction was dependent on the specific surface area.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1227-1229
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    A Recommended Integrated Mechanism to Enhance OSH Management of Blue-Collar Foreign Workers in Taiwan
    Autorzy:
    Liao, H. C.
    Cheng, S. F.
    Wang, Y.
    Lee, L. H.
    Powiązania:
    https://bibliotekanauki.pl/articles/90376.pdf
    Data publikacji:
    2014
    Wydawca:
    Centralny Instytut Ochrony Pracy
    Tematy:
    occupational safety and health
    Labor Safety and Health Act
    OSH training program
    manpower agency
    blue-collar foreign worker
    bezpieczeństwo i higiena pracy
    zdrowie
    szkolenie BHP
    Opis:
    This study examines the roles and functions of businesses, labor-exporting countries’ representative offices in Taiwan, religious organizations, and manpower agencies in promoting occupational safety and health (OSH). It also offers advice to Taiwanese authorities on making policies and improvements regarding the oversight mechanism mandated by the Labor Safety and Health Act, giving them an idea of what to focus on when enforcing control over blue-collar foreign workers’ OSH conditions. This study also proposes that Taiwanese authorities may serve not only as an overseer/inspector of those hiring blue-collar foreign workers in Taiwan, but also expand their role to lay down policies regarding a variety of OSH teaching materials in the blue-collar foreign workers’ native languages (spoken or written), the qualifications of translators in blue-collar foreign workers’ OSH training programs, and regulations concerning the longer hours such training programs take.
    Źródło:
    International Journal of Occupational Safety and Ergonomics; 2014, 20, 4; 537-549
    1080-3548
    Pojawia się w:
    International Journal of Occupational Safety and Ergonomics
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Multistep Heat-Treatment Effects on Electrospun Nd-Fe-B-O Nanofibers
    Autorzy:
    Jeon, E. J.
    Eom, N. S. A.
    Lee, J.
    Lee, B.
    Cho, H. M.
    On, J. S.
    Choa, Y.-H
    Kim, B. S.
    Powiązania:
    https://bibliotekanauki.pl/articles/354311.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Nd-Fe-B
    nanofibers
    electrospinning
    heat treatment
    Opis:
    Neodymium-Iron-Boron (Nd-Fe-B) magnets are considered to have the highest energy density, and their applications include electric motors, generators, hard disc drives, and MRI. It is well known that a fiber structure with a high aspect ratio and the large specific surface area has the potential to overcome the limitations, such as inhomogeneous structures and the difficulty in alignment of easy axis, associated with such magnets obtained by conventional methods. I n this work, a suitable heat-treatment procedure based on single-step and multistep treatments to synthesize sound electrospun Nd-Fe-B-O nanofibers of Φ572 nm was investigated. The single-step heat-treated (directly heat-treated at 800°C for 2 h in air) samples disintegrated along with the residual organic compounds, whereas the multistep heat-treated (sequential three-step heat-treated including three steps;: dehydration (250°C for 30 min in an inert atmosphere), debinding (650°C for 30 min in air), and calcination (800°C for 1 h in air)) fibers maintained sound fibrous morphology without any organic impurities. They could maintain such fibrous morphologies during the dehydration and debinding steps because of the relatively low internal pressures of water vapor and polymer, respectively. In addition, the NdFeO3 alloying phase was dominant in the multistep heat-treated fibers due to the removal of barriers to mass transfer in the interparticles.
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 3; 1433-1437
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Point-Contact Spectroscopy of Superconducting $MgCNi_3$ Single Crystals
    Autorzy:
    Pribulová, Z.
    Szabó, P.
    Kačmarčík, J.
    Samuely, P.
    Jang, D.
    Lee, H.
    Lee, S.
    Powiązania:
    https://bibliotekanauki.pl/articles/1813611.pdf
    Data publikacji:
    2008-01
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    74.50.+r
    Opis:
    The first point-contact spectroscopy measurements on $MgCNi_3$ single crystals of very good quality are presented. The measurements have been performed in the temperature range from 1.5 K up to 10 K and at magnetic fields up to 6 T. The superconducting energy gap Δ of the system is found to be scattered between 1 and 1.2 meV which gives the 2Δ/k $T_c$ ratio between BCS weak-coupling value of ~3.5 and a strong coupling of about 4.2. The excess current evaluated in magnetic field indicates the presence of a single energy gap.
    Źródło:
    Acta Physica Polonica A; 2008, 113, 1; 215-218
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Study On The Electro-Refining Of Tin In Acid Solution From Electronic Waste
    Badanie elektrorafinacji cyny w roztworze kwasu z e-odpadów
    Autorzy:
    Son, S. H.
    Park, S. C.
    Kim, J. H.
    Kim, Y. H.
    Lee, M. S.
    Ahn, J.-W.
    Powiązania:
    https://bibliotekanauki.pl/articles/352665.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    electrorefining
    tin
    electronic waste
    recycling
    high purity
    elektrorafinacja
    cyna
    odpady elektroniczne
    recykling
    Opis:
    The tin metal could be retractable from wasted tin scrap, sludge, and wasted electroplated solution hydrometallurgical treatment, and purification process. In order to be used as resource of electronic devices, the retracted crude metal should be purified to the extent of higher than 99.9%. In this study, tin electro-refining process was performed to purify the casted tin crude metal at various experimental conditions: at the current density of 3, 5A/dm2, and in various electrolytes such as hydrochloric acid, sulfuric acid and methansulfonic acid. Additional experiment was conducted using Rotating Disk Electrode (RDE) in order to investigate the rate determining step of tin electro-refining process. The current efficiency, 65.6%, was achievable at the condition of current density, 5A/dm2, and in the electrolyte of Hydrochloric acid. During tin electro-refining process, impurity dissolved from tin crude metal into the electrolyte was analyzed using Inductively Coupled Plasma Optical Emission Spectrometer (ICP-OES), and the result showed the concentration of impurity metal gradually increased. Quantitative analysis on casted tin crude metal showed that it consists of tin with 93.9 wt.% and several impurity metals of Ag, Bi, Pb, Cu, and etc. After tin electro-refining process, the purity of tin increased up to 99.985 wt.%.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1217-1220
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    High Temperature Oxidation Property of SiC Coating Layer Fabricated by Aerosol Deposition Process
    Autorzy:
    Ham, G.-S.
    Kim, S.-H.
    Park, J.-Y.
    Lee, K.-A.
    Powiązania:
    https://bibliotekanauki.pl/articles/352142.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    silicon carbide
    aerosol deposition
    coating
    high temperature oxidation
    Opis:
    This study investigated the high temperature oxidation property of SiC coated layer fabricated by aerosol deposition process. SiC coated layer could be successfully manufactured by using pure SiC powders and aerosol deposition on the Zr based alloy in an optimal process condition. The thickness of manufactured SiC coated layer was measured about 5 μm, and coating layer represented high density structure. SiC coated layer consisted of α-SiC and β-SiC phases, the same as the initial powder. The initial powder was shown to have been crushed to the extent and was deposited in the form of extremely fine particles. To examine the high temperature oxidation properties, oxidized weight gain was obtained for one hour at 1000°C by using TGA. The SiC coated layer showed superior oxidation resistance property than that of Zr alloy (substrate). The high temperature oxidation mechanism of SiC coated layer on Zr alloy was suggested. And then, the application of aerosol deposited SiC coated layer was also discussed.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1347-1351
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect of Trace Elements (Co, Cr) on the Microstructure and Physical Properties of Al-Si-Cu-Mg-Fe Extruded Alloy
    Autorzy:
    Ahn, S. S.
    Sharief, P.
    Lee, C. H.
    Son, H. T.
    Kim, Y. H.
    Kim, Y. C.
    Hong, S.
    Hong, S. J.
    Powiązania:
    https://bibliotekanauki.pl/articles/352787.pdf
    Data publikacji:
    2019
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Al-Si alloy
    microstructure
    extrusion
    coefficient of thermal expansion
    trace elements
    Opis:
    Trace elements Co, Cr were added to investigate their influence on the microstructure and physical properties of Al-Si extruded alloy. The Co, Cr elements were randomly distributed in the matrix, forms intermetallic phase and their existence wereconfirmed by XRD, EDS and SEM analysis. With addition of trace elements, the microstructure was modified, Si particle size was reduced and the growth rate of β-(Al5 FeSi) phase limited. Compared to parent alloy, hardness and tensile strength were enhanced while the linear coefficient of thermal expansion (CTE) was significantly reduced by 42.4% and 16.05% with Co and Cr addition respectively. It is considered that the low CTE occurs with addition of Co was due to the formation of intermetallic compound having low coefficient of thermal expansion. The results suggested that Co acts as an effective element in improving the mechanical properties of Al-Si alloy.
    Źródło:
    Archives of Metallurgy and Materials; 2019, 64, 3; 857-862
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Oxide Formation In Metal Injection Molding Of 316L Stainless Steel
    Tworzenie tlenków podczas wtryskiwania proszku stali nierdzewnej 316L
    Autorzy:
    Jang, J. M.
    Lee, W.
    Ko, S.-H.
    Han, C.
    Choi, H.
    Powiązania:
    https://bibliotekanauki.pl/articles/351352.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    powder injection molding
    sintering
    316L stainless steel
    sintering atmosphere
    micro parts
    wtryskiwanie proszku
    spiekanie
    stal nierdzewna 316L
    mikro-część
    Opis:
    The effects of sintering condition and powder size on the microstructure of MIMed parts were investigated using water-atomized 316L stainless steel powder. The 316L stainless steel feedstock was injected into micro mold with micro features of various shapes and dimensions. The green parts were debound and pre-sintered at 800°C in hydrogen atmosphere and then sintered at 1300°C and 1350°C in argon atmosphere of 5torr and 760torr, respectively. The oxide particles were formed and distributed homogeneously inside the sample except for the outermost region regardless of sintering condition and powder size. The width of layer without oxide particles are increased with decrease of sintering atmosphere pressure and powder size. The fine oxides act as the obstacle on grain growth and the high sintering temperature causes severe grain growth in micro features due to larger amount of heat gain than that in macro ones.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1281-1285
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Microstructure and Compression Properties of Fe-Cr-B Alloy Manufactured using Laser Metal Deposition
    Autorzy:
    Joo, Y.-A.
    Yoon, T.-S.
    Park, S.-H.
    Lee, K.-A.
    Powiązania:
    https://bibliotekanauki.pl/articles/352075.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Fe-Cr-B composite
    laser Metal Deposition
    bulk type
    microstructure
    compressive properties
    Opis:
    Fe-Cr-B alloy is a material with precipitation of boride inside Fe matrix, and it features outstanding hardness and wear resistance properties. However, Fe-Cr-B alloy is a difficult material to process, making it difficult to use as a bulk type structure material which requires delicate shapes. This study attempted to manufacture Fe-Cr-B alloy using a 3D printing process, laser metal deposition. This study also investigated the microstructure, hardness and compression properties of the manufactured alloy. Phase analysis results is confirmed that α-Fe phase as matrix and (Cr, Fe)2B phase as reinforcement phase. In the case of (Cr, Fe)2B phase, differences were observed according to the sample location. While long, coarse, unidirectional needle-type boride phases (~11 μm thickness) were observed in the center area of the sample, relatively finer boride phases (~6 μm thickness) in random directions were observed in other areas. At room temperature compression test results confirmed that the sample had a compression strength is approximately 2.1 GPa, proving that the sample is a material with extremely high strength. Observation of the compression fracture surface identified intergranular fractures in areas with needle-type boride, and transgranular fractures in areas with random borides. Based on this results, this study also reviewed the deformation behavior of LMD Fe-Cr-B alloy in relation to its microstructures.
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 3; 1459-1462
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Microstructure Evolution of Ni-Based ODS Superalloy Powders During Horizontal Rotary Ball Milling
    Autorzy:
    Lee, H.-E.
    Kim, Y. S.
    Park, J. K.
    Oh, S.-T.
    Powiązania:
    https://bibliotekanauki.pl/articles/355552.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    high energy ball milling
    Ni-base ODS superalloy
    particle and crystalline size
    microstructure
    Opis:
    Microstructure evolution of Ni-based oxide dispersion-strengthened alloy powders with milling time is investigated. The elemental powders having a nominal composition of Ni-15Cr-4.5Al-4W-2.5Ti-2Mo-2Ta-0.15Zr-1.1Y2O3 in wt % were ball-milled by using horizontal rotary ball milling with the change of milling velocity. Microstructure observation revealed that large aggregates were formed in the early stages of ball milling, and further milling to 5 h decreased particle size. The average crystalline size, estimated by the peak broadening of XRD, decreased from 28 nm to 15 nm with increasing milling time from 1 h to 5 h. SEM and EPMA analysis showed that the main elements of Ni and Cr were homogeneously distributed inside the powders after ball milling of 5 h.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1253-1255
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Manufacturing and Macroscopic Properties of Y2O3 Coating Layer on Ceramic (AlN) Substrate Fabricated by Aerosol Deposition
    Autorzy:
    Wi, D.-Y.
    Ham, G.-S.
    Kim, S.-H.
    Lee, K.-A.
    Powiązania:
    https://bibliotekanauki.pl/articles/353052.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    aerosol deposition
    Y2O3 coating layer
    AlN matrix
    nano indentation
    Opis:
    This study attempted to manufacture an Y2O3 ceramic coating layer on a ceramic (AlN) substrate using aerosol deposition (AD) and investigated its macroscopic properties. Pure Y2O3 powder with a polygonal shape and average size of 5.0 μm was used as initial feedstock. Using aerosol deposition with suitable process conditions, an Y2O3 coating layer was successfully fabricated on aluminum nitride (AIN). The thickness of the manufactured coating layer was approximately 10 mm. The coating layer consisted of Y2O3 phase identical to that in the initial powder, and no additional oxides were identified. In regard to the roughness of the Y2O3 coating layer, the average roughness (Ra) measured 1.32 μm, indicating that the surface roughness was relatively even compared to the initial powder size (5 μm). Mechanical properties of the Y2O3 coating layer were measured using nano indentation equipment, and the indentation modulus of the Y2O3 coating layer fabricated by aerosol deposition measured 136.5 GPa. The interface of the coating layer was observed using TEM, and the deposition mechanism of the Y2O3 coating layer manufactured by aerosol deposition was also discussed.
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 3; 1463-1466
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Experiments and simulations on the possibility of radiative contraction/collapse in the PF-1000 plasma focus
    Autorzy:
    Akel, M.
    Cikhardt, J.
    Kubes, P.
    Kunze, H.-J.
    Lee, S.
    Paduch, M.
    Saw, S. H.
    Powiązania:
    https://bibliotekanauki.pl/articles/147275.pdf
    Data publikacji:
    2016
    Wydawca:
    Instytut Chemii i Techniki Jądrowej
    Tematy:
    plasma focus
    radiative collapse
    radiation losses
    simulations
    Opis:
    Experimental studies of discharges in the plasma focus facility with neon filling and respective numerical simulations employing the radiative Lee code are reported. The pinch currents exceed the Pease-Braginskii current, which indicates that radiative losses are larger than heating and that contraction of the formed plasma should occur. Both of these effects were indeed observed. Parallel numerical simulations were crucial for the identifi cation of such an effect.
    Źródło:
    Nukleonika; 2016, 61, 2; 145-148
    0029-5922
    1508-5791
    Pojawia się w:
    Nukleonika
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    The Development of Ship Watch Keeping Supporting Aids
    Autorzy:
    Im, N.
    Kim, E. K.
    Han, S. H.
    Jeong, J. S.
    Lee, S. M.
    Powiązania:
    https://bibliotekanauki.pl/articles/117602.pdf
    Data publikacji:
    2013
    Wydawca:
    Uniwersytet Morski w Gdyni. Wydział Nawigacyjny
    Tematy:
    Ship Watchkeeping
    Deck Officers
    Navigation Visual Supporting System
    Intelligent Technology
    Dangerous Floating Objects
    Binocular Telescope
    laser distance measuring unit
    Sea Trial Test
    Opis:
    This study deals with the development of ship watch keeping supporting aids that will be useful for ship deck officers in recognizing navigational harmful obstacles such as sea marks and small floating objects on the sea. The developed watch keeping supporting aids is made up of four components; a composite video sensor to produce video signal, a laser distance measuring part, a Pan/Tilt part and a central control part. The system was installed in a ship in order to verify its performance of the recognition ability on the sea. The comparison was made between the recognition ability of the system and that of watch keeping deck officers’. The image from the watch keeping supporting system was found to be more recognizable than that of a binocular telescope within a 5 km distance. The newly suggested system is expected to be used to recognize small dangerous floating objects more easily when navigation deck officers have a duty of watch keeping for navigation especially near harbor area.
    Źródło:
    TransNav : International Journal on Marine Navigation and Safety of Sea Transportation; 2013, 7, 4; 501-506
    2083-6473
    2083-6481
    Pojawia się w:
    TransNav : International Journal on Marine Navigation and Safety of Sea Transportation
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Self-Consolidation Mechanism of Ti5Si3 Compact Obtained by Electro-Discharge-Sintering Directly from Physically Blended Ti-37.5 At.% Si Powder Mixture
    Autorzy:
    Chang, S. Y.
    Cheon, Y. W.
    Yoon, Y. H.
    Kim, Y. H.
    Kim, J. Y.
    Lee, Y. K.
    Lee, W. H.
    Powiązania:
    https://bibliotekanauki.pl/articles/353022.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    sintering
    mechanical alloying
    powder consolidation
    intermetallic compounds
    titanium silicide
    Opis:
    Characteristics of electro-discharge-sintering of the Ti-37.5at.% Si powder mixture was investigated as a function of the input energy, capacitance, and discharge time without applying any external pressure. A solid bulk of Ti5Si3 was obtained only after in less than 129 μsec by the EDS process. During a discharge, the heat is generated to liquefy and alloy the particles, and which enhances the pinch pressure can condensate them without allowing a formation of pores. Three step processes for the self-consolidation mechanism during EDS are proposed; (a) a physical breakdown of oxide film on elemental as-received powder particles, (b) alloying and densifying the consolidation of powder particles by the pinch pressure, and (c) diffusion of impurities into the consolidated surface.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1299-1302
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Variable-Focus Fluid Lens Using an Electromagnetic Actuator
    Autorzy:
    Lee, J.
    Park, K.
    Choi, J.
    Kim, H.
    Kong, S.
    Powiązania:
    https://bibliotekanauki.pl/articles/1399681.pdf
    Data publikacji:
    2013-02
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    85.85.+j
    42.79.Bh
    Opis:
    A variable-focus fluid lens controlled by an electromagnetic actuator and its characteristics are presented in this paper. The repulsive force between an NdFeB magnet and a solenoid through electromagnetic induction causes deflections in the elastomeric membranes integrated in the lens resulting in a focal-length change. The controllability of the focal length of the fabricated lens with an aperture size of 2 mm was approximately from infinity to 15 mm (with input current of 100 mA). The actuator including the solenoid was carefully designed to avoid thermal crosstalk of the lens fluid and magnet from the electromagnetic induction of the solenoid. The settling time to form a convex shape of the lens membrane was approximately 2.5 ms at an input current of 20 mA.
    Źródło:
    Acta Physica Polonica A; 2013, 123, 2; 202-204
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect of Surfactant Addition on Bi2Te3 Nanostructures Synthesized by Hydrothermal Method
    Autorzy:
    Dharmaiah, P.
    Lee, C. H.
    Madavali, B.
    Hong, S.-J.
    Powiązania:
    https://bibliotekanauki.pl/articles/351609.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    bismuth telluride
    hydrothermal synthesis
    spark plasma sintering
    thermoelectric materials
    X-ray diffraction
    Opis:
    In the present work, we have prepared Bi2Te3 nanostructures with different morphologies such as nano-spherical, nanoplates and nanoflakes obtained using various surfactant additions (EG, PVP, and EDTA) by a hydrothermal method. The shape of the nanoparticles can be controlled by addition of surfactants. The samples were characterized by x-ray diffraction (XRD) and scanning electron microscopy (SEM). It is found that the minority BiOCl phase disappears after maintained pH at 10 with EG as surfactant. SEM bulk microstructure reveals that the sample consists of fine and coarse grains. Temperature dependence of thermoelectric properties of the nanostructured bulk sample was investigated in the range of 300-450K. The presence of nanograins in the bulk sample exhibits a reduction of thermal conductivity and less effect on electrical conductivity. As a result, a figure of merit of the sintered bulk sample reached 0.2 at 400 K. A maximum micro Vickers hardness of 102 Hv was obtained for the nanostructured sample, which was higher than the other reported results.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1005-1010
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Sire pedigree error estimation and sire verification of the Taiwan dairy cattle population by using SNP markers
    Autorzy:
    Chao, C.H.
    Yeh, Y.H.
    Chen, Y.M.
    Lee, K.H.
    Wang, S.H.
    Lin, T.Y.
    Powiązania:
    https://bibliotekanauki.pl/articles/16539078.pdf
    Data publikacji:
    2022
    Wydawca:
    Polska Akademia Nauk. Czasopisma i Monografie PAN
    Tematy:
    Holstein cattle
    genetic testing
    sire pedigree
    Opis:
    Information regarding the correct pedigree of and relationship between animals is useful for managing dairy breeding, reducing inbreeding, estimating breeding value, and establishing correct breeding programs. Additionally, the successful implementation of progeny testing is crucial for improving the genetics of dairy cattle, which depends on the availability of correct pedigree information. Incorrect pedigree information leads to bias in bull evaluation. In this study, Neogen GeneSeek Genomic Profiler (GGP) 50K SNP chips were used to identify and verify the sire of Taiwanese Holstein dairy cattle and analyze the reasons that lead to incorrect sire records. Samples were collected from 2,059 cows of 36 dairy farms, and the pedigree information was provided by breeders. The results of sire verification can be divided into three categories: submitted unconfirmed sire, submitted confirmed sire, and incorrectly submitted verified sire. Data on the sires of 1,323 (64.25%) and 572 (27.78%) dairy cows were verified and discovered, respectively. Sires of 1,895 (92.03%) dairy cattle were identified, which showed that the paternal pedigree of dairy cattle could be discovered and verified through genetic testing. An error-like analysis revealed that the data of 37 sires were incorrectly recorded because the bull’s NAAB code number was incorrectly entered into the insemination records: for 19 sires, the wrong bull was recorded because the frozen semen of a bull placed in the wrong storage tank was used, 6 had no sire records, and for 12 sires, the NAAB code of the correct bull was recorded but with a wrong stud code, marketing code, or unique number for the stud or breed. To reduce recorded sire error rates by at least 27.78%, automated identification of the mated bull must be adopted to reduce human error and improve dairy breeding management on dairy farms.
    Źródło:
    Polish Journal of Veterinary Sciences; 2022, 25, 1; 61-65
    1505-1773
    Pojawia się w:
    Polish Journal of Veterinary Sciences
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Evaluation of Surface Characteristics and Physical Properties on Biodegradable Magnesium-Calcium Alloys by Anodic Oxidation
    Autorzy:
    Kim, J.
    Lee, J.
    Yang, H.
    Park, S.
    Lim, H.
    Oh, G.
    Yun, K.
    Powiązania:
    https://bibliotekanauki.pl/articles/1191716.pdf
    Data publikacji:
    2016-04
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    87.85.jj
    87.85.jc
    Opis:
    The purpose of this study was to determine the effect of calcium (Ca) on the surface characteristics and physical properties of magnesium-calcium alloys after anodization. A novel binary alloy Mg-xCa (in which x=0.5, 1, or 5 wt.%) was cast by combining magnesium (99.9%) and calcium (99.9%) in an argon gas (99.99%) atmosphere. A magnesium alloy rod having a diameter of 15 mm was cut into discs, each 2 mm thick. The specimens were subjected to anodic oxidation at 120 V for 15 minutes at room temperature in an electrolyte solution consisting of calcium gluconate, sodium hexametaphosphate, and sodium hydroxide. Surface and cross-sectional morphological changes were observed using scanning electron microscopy, and the microstructures and phases were detected by means of X-ray diffraction. Hardness and surface roughness were assessed by means of a Vickers hardness tester and a surface roughness meter, respectively. The results show that the physical properties of these magnesium-calcium alloys have been improved, because it was possible to control the dissolution rate according to the amount of calcium added.
    Źródło:
    Acta Physica Polonica A; 2016, 129, 4; 736-741
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Double Step Sintering Behavior Of 316L Nanoparticle Dispersed Micro-Sphere Powder
    Dwuetapowe spiekanie mikrosferycznych nanocząstek proszku 316L
    Autorzy:
    Jeon, B.
    Sohn, S. H.
    Lee, W.
    Han, C.
    Kim, Y. D.
    Choi, H.
    Powiązania:
    https://bibliotekanauki.pl/articles/355221.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    316L stainless steel
    nanoparticle dispersed micro-sphere
    pulse wire explosion
    sintering
    stal nierdzewna 316L
    spiekanie dwuetapowe
    mikrosferyczne nanocząstki
    Opis:
    316L stainless steel is a well-established engineering material and lots of components are fabricated by either ingot metallurgy or powder metallurgy. From the viewpoints of material properties and process versatility, powder metallurgy has been widely applied in industries. Generally, stainless steel powders are prepared by atomization processes and powder characteristics, compaction ability, and sinterability are quite different according to the powder preparation process. In the present study, a nanoparticle dispersed micro-sphere powder is synthesized by pulse wire explosion of 316L stainless steel wire in order to facilitate compaction ability and sintering ability. Nanoparticles which are deposited on the surface of micro-powder are advantageous for a rigid die compaction while spherical micro-powder is not to be compacted. Additionally, double step sintering behavior is observed for the powder in the dilatometry of cylindrical compact body. Earlier shrinkage peak comes from the sintering of nanoparticle and later one results from the micro-powder sintering. Microstructure as well as phase composition of the sintered body is investigated.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1155-1158
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Biological Evaluation of Anodized Biodegradable Magnesium-Calcium Alloys
    Autorzy:
    Kim, J.
    Lee, J.
    Lee, K.
    Park, S.
    Lim, H.
    Park, C.
    Bae, J.
    Yun, K.
    Powiązania:
    https://bibliotekanauki.pl/articles/1398763.pdf
    Data publikacji:
    2016-04
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    87.85.jj
    87.85.J-
    Opis:
    The objective of this study was to evaluate the biocompatibility of studied binary magnesium-calcium (Mg-Ca) alloys for biodegradable intraosseous implants. Mg is necessary for health and is a non-toxic biodegradable material that decomposes naturally in the body. Nevertheless, Mg has been implicated in problems including diminished physical properties and corrosion resistance when degradation is too rapid prior to bone healing. This study has explored the effect of Ca on the corrosion resistance and biological evaluation after anodizing treatment with different contents of Ca alloy. Binary Mg-0.5Ca, Mg-1Ca and Mg-5Ca alloys were prepared by the casting method under an argon atmosphere and cut into disc-shaped pieces. Pure Mg alloy was used as the control. Anodic oxidation was performed for 15 minutes at a voltage of 120 V using an electrolyte solution containing Ca gluconate, sodium hexametaphosphate, and sodium hydroxide at room temperature. Corrosion resistance was analyzed using a corrosion tester. After a hydrogen evolution test, the surface pattern and phase changes were observed on a scanning electron microscop (SEM) and energy dispersive spectroscop (EDS). Microscopic evaluation of the adhesion and cell biological functions of Mg was conducted by observing the response of human fetal osteoblastic 1.19 cells with regard to changes in surface film properties, depending on the amount of Ca. Our results support the view that in Mg-xCa alloys (x=0.5, 1, 5 wt.%) treated using anodic oxidation, the increasing Ca content controls the rate of decomposition and improves corrosion resistance.
    Źródło:
    Acta Physica Polonica A; 2016, 129, 4; 728-735
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    AC Microcalorimetry of Superconducting $MgCNi_3$ Single Crystals
    Autorzy:
    Kačmarčík, J.
    Pribulová, Z.
    Samuely, P.
    Marcenat, C.
    Klein, T.
    Jang, D.
    Lee, H.
    Lee, S.
    Powiązania:
    https://bibliotekanauki.pl/articles/1813689.pdf
    Data publikacji:
    2008-01
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    74.70.Ad
    74.25.Bt
    Opis:
    The low-temperature specific heat of single-crystal samples of superconducting $MgCNi_3$ with typical dimensions 200 μm were measured for the first time. A computer controlled ac microcalorimeter using an optical fiber and an infrared light-emitting diode as the heat source was used down to 2 K at magnetic fields up to 8 T. The specific heat data suggest a moderate coupling in $MgCNi_3$.
    Źródło:
    Acta Physica Polonica A; 2008, 113, 1; 363-366
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Low-velocity impact characteristics of composite plates with shape memory alloy wires
    Niskoprędkościowe charakterystyki uderzeniowe płyt kompozytowych zawierających włókna ze stopów z pamięcią kształtu
    Autorzy:
    Rim, M.-S.
    Kim, E.-H.
    Lee, I.
    Choi, I.-H.
    Ahn, S.-M.
    Koo, K.-N.
    Bae, J.-S.
    Roh, J.-H.
    Powiązania:
    https://bibliotekanauki.pl/articles/279293.pdf
    Data publikacji:
    2011
    Wydawca:
    Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
    Tematy:
    shape memory alloy
    SMAHC
    composite
    low-velocity impact
    impact resistance
    Opis:
    To investigate impact characteristics of shape memory alloy hybrid com- posites (SMAHC), several experiments were performed. Tensile tests of shape memory alloy (SMA) wires were carried out to investigate thermomechanical properties, and low-velocity impact tests of SMAHC plates and conventional composite plates without SMAs at the critical energy level. low-velocity impact tests of several types of composite plates, including composite plates with embedded SMAs/Fe/Al wires and conventional composite plates, were also done. Results of these experiments show that embedding SMAs in a composite plate can improve the impact resistance. Lastly, low-velocity impact tests of SMAHC plates with SMA wires embedded at different positions through the thickness were performed in an effort to improve the impact resistance. Embedding SMA wires at a lower position in the composite plates was the most effective for improving the impact resistance.
    Do analizy charakterystyk uderzeniowych hybrydowych kompozytów SMAHC zwierających włókna SMA ze stopów wykazujących efekt pamięci kształtu przeprowadzono szereg badań eksperymentalnych. Przeprowadzono próby na rozciąganie włókien SMA w celu zbadania ich właściwości termomechanicznych oraz niskoprędkościowe testy uderzeniowe płyt SMAHC oraz konwencjonalnych płyt laminowanych przy energii krytycznej. Wykonano także testy dla płyt kompozytowych zawierających włókna SMA/Fe/Al. Rezultaty doświadczeń pokazały, że wbudowanie w strukturę laminatu włókien SMA może zwiększyć odporność kompozytu na obciążenie uderzeniowe. Opisano również badania eksperymentalne płyt SMAHC z włóknami SMA wbudowanymi na różnej głębokości. Wykazano, że najlepsze parametry posiadają kompozyty z włóknami umieszczonymi możliwie daleko od uderzanej powierzchni.
    Źródło:
    Journal of Theoretical and Applied Mechanics; 2011, 49, 3; 841-857
    1429-2955
    Pojawia się w:
    Journal of Theoretical and Applied Mechanics
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Influence of the Calcination Temperature on the Optical and Mechanical Properties of Y2O3-MgO Nanocomposite
    Autorzy:
    Yong, S.-M.
    Choi, D. H.
    Lee, K.
    Ko, S.-Y.
    Cheong, D.-I.
    Powiązania:
    https://bibliotekanauki.pl/articles/351252.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    infrared transparent ceramics
    Y2O3-MgO nanocomposites
    sol-gel combustion synthesis
    calcination
    spark plasma sintering
    Opis:
    Y2O3-MgO nanocomposites are one of the most promising materials for hypersonic infrared windows and domes due to their excellent optical transmittance and mechanical properties. In this study, influence of the calcination temperature of Y2O3-MgO nanopowders on the microstructure, IR transmittance, and hardness of Y2O3-MgO nanocomposites was investigated. It was found that the calcination temperature is related to the presence of residual intergranular pores and grain size after spark plasma sintering. The nanopowders calcined at 1000°C exhibits the highest infrared transmittance (82.3% at 5.3 μm) and hardness (9.99 GPa). These findings indicated that initial particle size and distribution of the nanopowders are important factors determining the optical and mechanical performances of Y2O3-MgO nanocomposites.
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 3; 1481-1484
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect Of The Desorption-Recombination Temperature On The Microstructure And Magnetic Properties Of HDDR Processed Nd-Fe-B Powders
    Wpływ temperatury desorpcji-rekombinacji na mikrostrukturę i właściwości magnetyczne proszków Nd-Fe-B przetwarzanych metodą HDDR
    Autorzy:
    Lee, J.-G.
    Cha, H.-R.
    Liu, S.
    Yu, J.-H.
    Baek, Y.-K.
    Kwon, H.-W.
    Powiązania:
    https://bibliotekanauki.pl/articles/353723.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Nd-Fe-B
    HDDR
    permanent magnet
    grain boundary
    metoda HDDR
    magnes trwały
    granica ziarna
    Opis:
    The effect of the desorption-recombination temperature on the microstructure and magnetic properties of hydrogenation-disproportionation-desorption-recombination (HDDR) processed Nd-Fe-B powders was studied. The NdxB6.4Ga0.3Nb20.2Febal (x=12.5-13.5, at.%) casting alloys were pulverized after homogenizing annealing, and then subjected to HDDR treatment. During the HDDR process, desorption-recombination (DR) reaction was induced at two different temperature, 810°C and 820°C. The higher Nd content resulted in enhanced coercivity of the HDDR powder, and which was attributed to the thicker and more uniform Nd-rich phase along grain boundaries. But this uniform Nd-rich phase induced faster grain growth. The remanence of the powder DR-treated at 820°C is higher than that DR-treated at 810°C. In addition, it was also confirmed that higher DR temperature is much more effective to improve squareness.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1499-1501
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Quantitative Analysis of Cryomilled Nanocrystalline Ti-6Al-4V Alloy Powder by X-Ray Diffraction
    Autorzy:
    Oh, M.
    Yu, H. K.
    Lee, J.-H.
    Oh, M. C.
    Jung, S.-H.
    Ahn, B.
    Powiązania:
    https://bibliotekanauki.pl/articles/356265.pdf
    Data publikacji:
    2018
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    nanocrystalline
    cryomilling
    Ti alloy
    X-ray diffraction
    size-strain plot method
    Opis:
    A nanocrystalline Ti alloy powder was fabricated using cryomilling. The grain size and lattice strain evolution during cryomilling were quantitatively analyzed using X-ray diffraction (XRD) based on the Scherrer equation, Williamson-Hall (W-H) plotting method, and size-strain (S-S) method assuming uniform deformation. Other physical parameters including stress and strain have been calculated. The average crystallite size and the lattice strain evaluated from XRD analysis are in good agreement with the result of transmission electron microscopy (TEM).
    Źródło:
    Archives of Metallurgy and Materials; 2018, 63, 3; 1439-1442
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Compositional Dependence of Hardness of Ge-Sb-Se Glass for Molded Lens Applications
    Zależność stężeniowa twardości szkła Ge-Sb-Se do zastosowań na formowane soczewki
    Autorzy:
    Park, J. K.
    Lee, J. H.
    Shin, S. Y.
    Yi, J. H.
    Lee, W. H.
    Park, B. J.
    Choi, J. H.
    Kim, N. Y.
    Choi, Y. G.
    Powiązania:
    https://bibliotekanauki.pl/articles/352228.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    chalcogenide glasses
    Ge-Sb-Se glass
    infrared lens
    molded lens
    infrared camera
    szkło
    Ge-Sb-Se
    soczewki formowane
    twardość szkła
    kamera termowizyjna
    Opis:
    Chalcogenide glass in the ternary Ge-Sb-Se system is inherently moldable, thus being considered as a strong candidate material for use in infrared-transmitting lens applications from the viewpoint of thermal and mechanical stability. In an effort to experimentally determine compositional region suitable for the molded lens applications, we evaluate its compositional dependence of hardness. Among the constituent atoms, Ge content turns out to exert a most conspicuous correlation with hardness. This phenomenological behavior is then explained in connection with the structural evolution that Ge brings about.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1205-1208
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Formation of Tungsten/Ammonium Perchlorate Composites and Their Reaction Kinetics
    Autorzy:
    Shim, H.-M.
    Lee, E.-A.
    Kim, J.-K.
    Kim, H.-S.
    Koo, K.-K.
    Powiązania:
    https://bibliotekanauki.pl/articles/358373.pdf
    Data publikacji:
    2015
    Wydawca:
    Sieć Badawcza Łukasiewicz - Instytut Przemysłu Organicznego
    Tematy:
    ammonium perchlorate
    composite
    thermal decomposition
    Opis:
    The reaction kinetics of tungsten nanoparticles/ammonium perchlorate (W/AP) composites, produced by a spray drying technique, were analyzed and compared with those of neat AP particles and aluminum nanoparticles/AP (Al/AP) composites. The W was found to raise the onset temperature of the thermal decomposition of AP by increasing the activation energy, whereas Al conversely lowered the onset temperature of AP due to the decreased activation energy. From the master plots of kinetic models with the experimental data, the Prout-Tompkins model and the 1-D diffusion controlled model were found to describe the low-temperature decomposition (LTD) and high-temperature decomposition (HTD), respectively, giving remarkable agreement with experimental curves for all heating rates. The presence of W was found to increase the HTD zone width compared with that of neat AP particles and Al/AP composites. Analysis of the average activation energy and pre-exponential factor showed that W increases the energy barrier and the frequency of occurrence of the reaction compared with that of neat AP particles at the LTD state, whereas W decreases both of them at the HTD state. The effect of Al was also shown to be similar to that of W, but the magnitudes of the variation in activation energy and the pre-exponential factor were relatively small.
    Źródło:
    Central European Journal of Energetic Materials; 2015, 12, 4; 703-722
    1733-7178
    Pojawia się w:
    Central European Journal of Energetic Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Oxidation Behavior of Steel with Cr Content and Water Flow Rate
    Autorzy:
    Kim, D.-J.
    Kim, K. M.
    Shin, J. H.
    Cheong, Y. M.
    Lee, E. H.
    Lee, G. G.
    Kim, S. W.
    Kim, H. P.
    Choi, M. J.
    Lim, Y. S.
    Hwang, S. S.
    Powiązania:
    https://bibliotekanauki.pl/articles/351548.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    steel
    flow accelerated corrosion
    Cr content
    flow rate
    surface oxides
    Opis:
    Fast water flow facilitates ferrous ion transport leading to flow accelerated corrosion (FAC) of carbon steel and the possibility of a large accident through a failure of a secondary pipe in a nuclear power plant. Ion transport is directly linked to oxide properties such as the thickness, chemical composition and porosity. This work deals with a precise observation of the cross section of the corroded specimen focusing on an oxide passivity and its thickness using SEM (scanning electron microscope) and TEM (transmission electron microscope) as well as an apparent weight loss and a surface observation for the specimens corroded using a rotating cylindrical electrode autoclave system in pure water of pH 7 at 150°C having dissolved oxygen below 1 ppb within a flow rate range of 0 to 10 m/s. The Cr content in steel was changed from 0.02 to 2.4 wt%. Increasing the Cr content in the alloy, the FAC rate and oxide thickness decreased. The oxide porosity tends to decrease with the Cr content and immersion time owing to the development of Cr containing oxide. The oxidation behavior is not changed with the immersion time.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1383-1387
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Studies on the effect of coal particle size on biodepyritization of high sulfur coal in batch bioreactor
    Autorzy:
    Singh, S.
    Srichandan, H.
    Pathak, A.
    Gahan, Ch. S.
    Lee, S.
    Kim, D. J.
    Kim, B. G.
    Powiązania:
    https://bibliotekanauki.pl/articles/778523.pdf
    Data publikacji:
    2015
    Wydawca:
    Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
    Tematy:
    biodepyritization
    coal
    pyrite
    stirred tank bioreactor
    Opis:
    The moderate thermophilic mix culture bacteria were used to depyritize the Illinois coal of varying particle sizes (-100 μm, 100-200 μm, +200 μm). Mineral libration analysis showed the presence of pyrite along with other minerals in coal. Microbial depyritization of coal was carried out in stirred tank batch reactors in presence of an iron-free 9K medium. The results indicate that microbial depyritization of coal using moderate thermophiles is an efficient process. Moreover, particle size of coal is an important parameter which affects the efficiency of microbial depyritization process. At the end of the experiment, a maximum of 75% pyrite and 66% of pyritic sulphur were removed from the median particle size. The XRD analysis showed the absence of pyrite mineral in the treated coal sample. A good mass balance was also obtained with net loss of mass ranging from 5-9% showing the feasibility of the process for large scale applications.
    Źródło:
    Polish Journal of Chemical Technology; 2015, 17, 1; 97-102
    1509-8117
    1899-4741
    Pojawia się w:
    Polish Journal of Chemical Technology
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Preparation Of Fine Grained SiC At Reduced Temperature By Two-Step Sintering
    Wytwarzanie drobnoziarnistego SiC w obniżonej temperaturze przez dwuetapowe spiekanie
    Autorzy:
    Kim, K.-W.
    Oh, K.-S.
    Lee, H.
    Kim, B. S.
    Chung, T.-J.
    Powiązania:
    https://bibliotekanauki.pl/articles/353772.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    SiC
    liquid phase
    two step sintering
    coarsening
    hardness
    faza ciekła
    spiekanie dwuetapowe
    odporność
    twardość
    Opis:
    Two-step sintering route was applied for the densification SiC by promoting the role of liquid phase. The specimen contained 8 vol% of liquid phase composed of Al2O3 and Y2O3. The heating schedule consisted with initial rapid heating to 2000°C and immediate quenching to 1700 or 1750°C. By heating at elevated temperature, even distribution of the liquid phase was intended. The heat treatment at reduced temperature was to suppress the evaporative loss of the liquid and to secure the time for densification. The two-step sintering effectively suppressed loss of mass and coarsening. The resultant SiC was thus dense and was composed of fine grains exhibiting hardness of 2321 kgf/mm2.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1539-1542
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Characterization of Cladding Hull Wastes from Used Nuclear Fuels
    Charakterystyka odpadów z okładzin reaktora wodnego ciśnieniowego
    Autorzy:
    Kang, K. H.
    Lee, C. H.
    Jeon, M. K.
    Han, S. Y.
    Park, G. I.
    Hwang, S.-M.
    Powiązania:
    https://bibliotekanauki.pl/articles/357036.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    used nuclear fuels
    metal waste
    cladding hulls
    zircaloy
    radioactivity
    reaktor wodny ciśnieniowy
    odpady metalowe
    odpady z okładzin
    radioaktywność
    Opis:
    Used cladding hulls from pressurized water reactor (PWR) are characterized to provide useful information for the treatment and disposal of cladding hull wastes. The radioactivity and the mass of gamma emitting nuclides increases with an increase in the fuel burn-up and their removal ratios are found to be more than 99 wt.% except Co-60 and Cs-137. In the result of measuring the concentrations of U and Pu included in the cladding hull wastes, most of the residues are remained on the surface and the removal ratio of U and Pu are revealed to be over 99.98 wt.% for the fuel burn-up of 35,000 MWd/tU. An electron probe micro-analyzer (EPMA) line scanning shows that radioactive fission products are penetrated into the Zr oxide layer, which is proportional to the fuel burn-up. The oxidative decladding process exhibits more efficient removal ratio of radionuclides.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1199-1203
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect of Heat Treatment on Microstructure and Impact Toughness of Ti-6Al-4V Manufactured by Selective Laser Melting Process
    Autorzy:
    Lee, K.-A.
    Kim, Y.-K.
    Yu, J.-H.
    Park, S.-H.
    Kim, M.-C.
    Powiązania:
    https://bibliotekanauki.pl/articles/354570.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    selective laser melting
    Ti-6Al-4V
    microstructure
    impact toughness
    heat treatment
    Opis:
    This study manufactured Ti-6Al-4V alloy using one of the powder bed fusion 3D-printing processes, selective laser melting, and investigated the effect of heat treatment (650°C/3hrs) on microstructure and impact toughness of the material. Initial microstructural observation identified prior-β grain along the building direction before and after heat treatment. In addition, the material formed a fully martensite structure before heat treatment, and after heat treatment, α and β phase were formed simultaneously. Charpy impact tests were conducted. The average impact energy measured as 6.0 J before heat treatment, and after heat treatment, the average impact energy increased by approximately 20% to 7.3 J. Fracture surface observation after the impact test showed that both alloys had brittle characteristics on macro levels, but showed ductile fracture characteristics and dimples at micro levels.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1341-1346
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Surface Modification of Self-Consolidated Microporous Ti Implant Compacts Fabricated by Electro-Discharge-Sintering in Air
    Autorzy:
    Jo, Y. J.
    Yoon, Y. H.
    Kim, Y. H.
    Chang, S. Y.
    Kim, J. Y.
    Lee, Y. K.
    Van Tyne, C. J.
    Lee, W. H.
    Powiązania:
    https://bibliotekanauki.pl/articles/356790.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    titanium
    implant
    porous
    sintering
    X-ray photoelectron spectroscopy (XPS)
    Opis:
    A single pulse of 0.75-2.0 kJ/0.7g of atomized spherical Ti powders from 300 mF capacitor was applied to produce a microporous Ti implant compact by electro-discharge-sintering (EDS). A solid core in the middle of the compact surrounded by a microporous layer was found. X-ray photoelectron spectroscopy was employed to study the surface characteristics of the EDS Ti compact and it revealed that Ti, C and O were the main constituents on the surface with a smaller amount of N. The surface was lightly oxidized and was primarily in the form of TiO2 resulting from the air oxidation during EDS processing. The lightly oxidized surface of the EDS compact also exhibited Ti nitrides such as TiN and TiON, which revealed that the reaction between air constituents and the Ti powders even in times as short as 128 msec.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1287-1291
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Thermal Conductivity and Microstructure of Copper Coated Graphite Composite by Spark Plasma Sintering Process
    Autorzy:
    Park, S. H.
    Kim, D. B.
    Lee, R. G.
    Son, I. J.
    Powiązania:
    https://bibliotekanauki.pl/articles/355632.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    metal matrix composites
    thermal conductivity
    thermal expansion
    interfacial bonding
    spark plasma sintering
    Opis:
    This study focuses on the fabrication of thermal management material for power electronics applications using graphite flake reinforced copper composites. The manufacturing route involved electroless plating of copper in the graphite flake and sintering process are optimized. The microstructures, interface, thermal properties, and relative density of graphite/Cu composites are investigated. The relative density of the composites shows 99.5% after sintering. Thermal conductivities and coefficients of thermal expansion of this composites were 400-480 Wm-1K-1 and 8 to 5 ppm k-1, respectively. Obtained graphite nanoplatelets-reinforced composites exhibit excellent thermo-physical properties to meet the heat dispersion and matching requirements of power electronic devices to the packaging materials.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1303-1306
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Effect Of Different Mechanical Milling Processes On Morphology And Microstructural Changes Of Nano And Micron Al-Powders
    Wpływ różnych procesów mielenia na morfologię i mikrostrukturę nanometrycznych i mikronowych proszków Al
    Autorzy:
    Kim, H.-S.
    Madavali, B.
    Eom, T.-J.
    Kim, C.- M.
    Koo, J.-M.
    Lee, T. H.
    Hong, S.-J.
    Powiązania:
    https://bibliotekanauki.pl/articles/355715.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Al alloys
    high-energy ball milling
    low energy ball milling
    plastic deformation
    stopy Al
    wysokoenergetyczne mielenie kulkowe
    mielenie energooszczędne
    odkształcenia plastyczne
    Opis:
    In this research, effect of the various mechanical milling process on morphology and microstructural changes of nano and micron Al-powders was studied. The milling of Al-powders was performed by both high energy and low energy ball milling process. The influence of milling (pulverizing) energy on the structural changes of Al-powders was studied. Al-nanoparticles were agglomerated during the MA and its size was increased with increasing milling while micron Al-powder gets flattened shape during high energy ball milling due to severe plastic deformation. Meanwhile, structural evolution during high energy ball milling of the nano powder occurred faster than that of the micron powder. A slight shift in the position of X-ray diffraction peaks was observed in nano Al-powders but it was un-altered in macro Al-powders. The variation in lattice parameters was observed only for nano Al powders during the high energy ball milling due to lattice distortion.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1235-1239
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Carbon Co-Deposition During Gas Reduction of Water-Atomized Fe-Cr-Mo Powder
    Autorzy:
    Ali, B.
    Choi, S. H.
    Seo, S. J.
    Maeng, D. Y.
    Lee, C. G.
    Kim, T. S.
    Park, K. T.
    Powiązania:
    https://bibliotekanauki.pl/articles/352709.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    water atomization
    Fe-based powder
    oxide reduction
    powder metallurgy
    sinter-hardening alloys
    Opis:
    The water atomization of iron powder with a composition of Fe-3Cr-0.5Mo (wt.%) at 1600°C and 150 bar creates an oxide layer, which in this study was reduced using a mixture of methane (CH4) and argon (Ar) gas. The lowest oxygen content was achieved with a 100 cc/min flow rate of CH4, but this also resulted in a co-deposition of carbon due to the cracking of CH4. This carbon can be used directly to create high-quality, sinter hardenable steel, thereby eliminating the need for an additional mixing step prior to sintering. An exponential relationship was found to exist between the CH4 gas flow rate and carbon content of the powder, meaning that its composition can be easily controlled to suit a variety of different applications.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1119-1124
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Fabrication of AZ31/CNT Surface Nano-composite by Double-pass Friction Stir Processing
    Autorzy:
    Kim, J. Y.
    Hwang, J.-W.
    Kim, H. Y.
    Lee, S. M.
    Jung, W.-S.
    Byeon, J.-W.
    Powiązania:
    https://bibliotekanauki.pl/articles/355624.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    surface modification
    Double-pass Friction Stir Processing
    AZ31
    composite
    CNT
    Opis:
    Double-pass Friction Stir Processing (FSP) was applied to fabricate an AZ31/CNT nano-composite for surface hardening of lightweight structural components. The effects of double-pass FSP as well as groove depth (i.e., volume fraction of CNT) on the CNT distribution, dynamically recrystallized grain size, and resulting microhardness were studied. Double-pass FSP was performed for the CNT-filled plate-type specimen with different groove depths of 2, 3, and 4 mm. By applying double-pass FSP, the average size of CNT clusters decreased, implying a more homogeneous distribution. Compared with the FSPed specimen without CNT, grain size was refined from 19 μm to 3 μm and microhardness increased from 52 Hv to 83 Hv (i.e., 71% increase).
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1039-1042
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Supercontinuum fiber laser source for water quality and heavy metals detection
    Autorzy:
    Teh, P. C.
    Ho, Y. H.
    Ong, C. E.
    Lee, S. C.
    Lo, P. K.
    Lai, K. C.
    Yeap, K. H.
    Loh, S. H.
    Teh, P. S.
    Tey, K. L.
    Powiązania:
    https://bibliotekanauki.pl/articles/174135.pdf
    Data publikacji:
    2017
    Wydawca:
    Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
    Tematy:
    supercontinuum generation
    master oscillator power amplifier
    nonlinear optics
    transmittance measurement
    heavy metal contaminants
    Opis:
    We report a compact, all fiber, 150 ps fiber master oscillator power amplifier operating at 1064 nm that has the ability of producing a maximum average output power of 2.16 W with peak power as high as 10 kW. The output from the master oscillator power amplifier is spliced with a highly nonlinear photonic crystal fiber, generating a supercontinuum with an average power of 250 mW at repetition rate of 1 MHz and spectrum bandwidth spanning from 600 to 1700 nm. The developed supercontinuum system is used to detect the presence of heavy metal contaminants in water by a simple light transmittance method to ensure that the water is free from heavy metal contaminants and safe for consumption. The supercontinuum laser source was shone onto a water sample with a detector placed at another end in order to measure the transmitted supercontinuum light. By measuring the amount of light attenuated at particular wavelength, the concentration of heavy metal contaminants present in the water sample could be determined.
    Źródło:
    Optica Applicata; 2017, 47, 3; 445-456
    0078-5466
    1899-7015
    Pojawia się w:
    Optica Applicata
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Reaction Kinetics and Morphological Study of TiNb2O7 Synthesized by Solid-State Reaction
    Autorzy:
    Choi, S. H.
    Ali, B.
    Choi, K. S.
    Hyun, S. K.
    Sim, J. J.
    Choi, W. J.
    Joo, W.
    Lim, J. H.
    Lee, T. H.
    Kim, T. S.
    Park, K. T.
    Powiązania:
    https://bibliotekanauki.pl/articles/355326.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    solid state reaction
    kinetic analysis
    quantitative phase analysis
    TiNb2O7 synthesis
    Opis:
    Although TiNb2O7 is regarded as a material with high application potential in lithium-ion batteries (LIBs) and solid-oxide fuel cells (SOFCs), it has been difficult to find suitable cost-effective conditions for synthesizing it on a commercial scale. In this study, TiNb2O7 compounds were synthesized by a solid state synthesis process. For stoichiometrically precise synthesis of the TiNb2O7 phase, the starting materials, TiO2 and Nb2O5 were taken in a 1:1 molar ratio. Activation energy and reaction kinetics of the system were investigated at various synthesis temperatures (800,1000,1200, and 1400°C) and for various holding durations (1,5,10, and 20 h). Furthermore, change in the product morphology and particle size distribution were also evaluated as a function of synthesis temperature and duration. Additionally, quantitative phase analysis was conducted using the Rietveld refinement method. It was found that increases in the synthesis temperature and holding time lead to increase in the mean particle size from 1 to 4.5 μm. The reaction rate constant for the synthesis reaction was also calculated.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1051-1056
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Self-Consolidation Mechanism Of Porous Ti-6Al-4V Implant Prototypes Produced By Electro-Discharge-Sintering Of Spherical Ti-6Al-4V Powders
    Mechanizm autokonsolidacji prototypów porowatych implantów wytworzonych przez spiekanie sferycznych proszków Ti-6Al-4V
    Autorzy:
    Lee, W. H.
    Jo, Y. J.
    Kim, Y. H.
    Jo, Y. H.
    Seong, J. G.
    Van Tyne, C. J.
    Chang, S. Y.
    Powiązania:
    https://bibliotekanauki.pl/articles/356277.pdf
    Data publikacji:
    2015
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Ti-6Al-4V
    implant
    porous
    sintering
    electrodischarge
    porowatość
    spiekanie
    proszki spiekane
    Opis:
    Electro-Discharge-Sintering (EDS) was employed to fabricate Ti-6Al-4V porous implant prototypes from atomized powders (100 – 150 μm), that were subjected to discharges of 0.75 to 2.0 kJ/0.7g-powder from 150, 300, and 450 μF capacitors. Both fully porous and porous-surfaced Ti-6Al-4V compacts with various solid core sizes were self-consolidated in less than 86 – 155 μsec. It is known that EDS can simultaneously produce the pinch pressure to squeeze and deform powder particles and the heat to weld them together. The formation of a solid core in these prototypes depends on the amounts of both the pinch pressure and heat generated during a discharge. The size of the solid core and the thickness of the porous layer can be successfully controlled by manipulating the discharge conditions such as input energy and capacitance.
    Źródło:
    Archives of Metallurgy and Materials; 2015, 60, 2B; 1185-1189
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    An analysis on the thermal characteristics according to the viscosity of bearing lubricant and the cooling condition for the high speed motor spindle
    Autorzy:
    Choi, D. B.
    Lee, J. J.
    Kim, S. T.
    Kwon, H. D.
    Kim, C. Y.
    Powiązania:
    https://bibliotekanauki.pl/articles/1429194.pdf
    Data publikacji:
    2008
    Wydawca:
    Wrocławska Rada Federacji Stowarzyszeń Naukowo-Technicznych
    Tematy:
    high speed motor spindle
    thermal displacement cooling condition
    lubricant viscosity
    Opis:
    Thermal displacement of the high speed machine tools has a large influence on machining accuracy. The high speed motor spindle with many heat sources is widely used for the high speed machine tools recently. The important problem in this spindle is to reduce and minimize the thermal effects by motor and bearings. This paper presents the analysis on thermal characteristics for high speed motor spindle system with oil-air lubricated angular contact ceramic ball bearings and built-in motor. An analysis on the thermal characteristics of spindle is performed according to the cooling conditions and the viscosity of bearing lubricants by using finite element method. This results can be applied to the design and manufacturing for the high speed motor spindle.
    Źródło:
    Journal of Machine Engineering; 2008, 8, 4; 88-98
    1895-7595
    2391-8071
    Pojawia się w:
    Journal of Machine Engineering
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Fabrication of a Spherical Titanium Powder by Combined Combustion Synthesis and DC Plasma Treatment
    Autorzy:
    Choi, S. H.
    Ali, B.
    Hyun, S. K.
    Sim, J. J.
    Choi, W. J.
    Joo, W.
    Lim, J. H.
    Lee, Y. J.
    Kim, T. S.
    Park, K. T.
    Powiązania:
    https://bibliotekanauki.pl/articles/356067.pdf
    Data publikacji:
    2017
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    combustion synthesis
    DC plasma treatment
    titanium powder
    3D printing process
    combustion parameters
    Opis:
    Combustion synthesis is capable of producing many types of refractory and ceramic materials, as well as metals, with a relatively lower cost and shorter time frame than other solid state synthetic techniques. TiO2 with Mg as reductant were dry mixed and hand compacted into a 60 mm diameter mold and then combusted under an Ar atmosphere. Depending on the reaction parameters (Mg concentration 2 ≤ α ≤ 4), the thermocouples registered temperatures between 1160°C and 1710°C . 3 mol of Mg gave the optimum results with combustion temperature (Tc) and combustion velocity (Uc) values of 1372°C and 0.26 cm/s respectively. Furthermore, this ratio also had the lowest oxygen concentration in this study (0.8 wt%). After combustion, DC plasma treatment was carried out to spheroidize the Ti powder for use in 3D printing. The characterization of the final product was performed using X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, and N/O analysis.
    Źródło:
    Archives of Metallurgy and Materials; 2017, 62, 2B; 1057-1062
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Fabrication and Characterization of GaN/Polymer Composite p-n Junction with PEDOT Nanoparticle Interface Layer
    Autorzy:
    Kim, M.
    Jin, S.
    Choi, H.
    Kim, G.
    Yim, K.
    Kim, S.
    Nam, G.
    Yoon, H.
    Kim, Y.
    Lee, D.
    Kim, Jin
    Kim, Jong
    Leem, J.
    Powiązania:
    https://bibliotekanauki.pl/articles/1505152.pdf
    Data publikacji:
    2011-06
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    73.61.Ey
    81.15.Gh
    Opis:
    A heavily Si-doped GaN/polymer hybrid structure with p-type poly(3,4-ethylene-dioxythiophene):beta-1,3-glucan (PEDOT nanoparticle) interface layer has been fabricated. The Si-doped GaN thin film with carrier concentration of 1 × $10^{19} cm^{-3}$ was grown by metal-organic chemical vapor deposition. The PEDOT nanoparticle with various sizes ranging from 60 to 120 nm was synthesized via a miniemulsion polymerization process. The electrical conductivity of the PEDOT nanoparticle is less than 1.2 S/cm. The current-voltage (I-V) characteristic of the hybrid structure shows diode-like behavior. The I-V characteristic was examined in the framework of the thermionic emission model. The ideality factor of the structure without PEDOT nanoparticle interface layer is 12.9. However, the ideality factor of the hybrid structure with PEDOT nanoparticle interface layer is obtained as 1.9. The value of ideality factor is dramatically decreased by inserting the PEDOT nanoparticle interface layer.
    Źródło:
    Acta Physica Polonica A; 2011, 119, 6; 875-879
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Warm Tensile Deformation Behavior and Constitutive Equation of Supersaturated Solid-Solutionized Al-9Mg Extruded Alloy
    Autorzy:
    Yang, Seung Y.
    Kim, Bong H.
    Lee, Da B.
    Choi, Kweon H.
    Kim, Nam S.
    Ha, Seong H.
    Yoon, Young O.
    Lim, Hyun K.
    Kim, Shae
    Kim, Young J.
    Powiązania:
    https://bibliotekanauki.pl/articles/2048882.pdf
    Data publikacji:
    2021
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    aluminum alloy
    Al-9Mg alloy
    tensile test
    constitutive equation
    Opis:
    In this paper, as a purpose to apply the supersaturated solid-solutionized Al-9Mg alloy to the structural sheet parts of automotive, tensile tests were conducted under the various conditions and a constitutive equation was derived from the tensile test results. Al-9Mg alloy was produced using a special Mg master alloy containing Al2Ca during the casting process and extruded into the sheet. In order to study the deformation behavior of Al-9Mg alloy in warm temperature forming environments, tensile tests were conducted under the temperature of 373 K-573 K and the strain rate of 0.001/s~0.1/s. in addition, by using the raw data obtained from tensile tests, a constitutive equation of the Al-9Mg alloy was derived for predicting the optimized condition of the hot stamping process. Al-9Mg alloy showed uncommon deformation behavior at the 373 K and 473 K temperature conditions. The calculated curves from the constitutive equation well-matched with the measured curves from the experiments particularly under the low temperature and high strain rate conditions.
    Źródło:
    Archives of Metallurgy and Materials; 2021, 66, 4; 1013-1018
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Microstructure and Mechanical Properties of Hot-deformed AlMg4 Alloys with the Variations of Mn, Fe, and Si Contents
    Autorzy:
    Lee, Da B.
    Kim, Bong H.
    Choi, Kweon H.
    Yang, Seung Y.
    Kim, Nam S.
    Ha, Seong H.
    Yoon, Young O.
    Lim, Hyun K.
    Kim, Shae
    Hyun, Soong K..
    Powiązania:
    https://bibliotekanauki.pl/articles/351603.pdf
    Data publikacji:
    2020
    Wydawca:
    Polska Akademia Nauk. Czytelnia Czasopism PAN
    Tematy:
    Al-Mg alloy
    intermetallic compounds
    homogenization
    hot-rolling
    microstructure
    Opis:
    This paper aims to investigate the microstructural evolution and mechanical properties of hot-deformed AlMg4 alloys with Mn, Fe, and Si as the main impurities. For this purpose, solidification behavior and microstructural evolution during hot-rolling and heat-treatment processes are investigated by using theoretical calculations and experimental characterization. The crystallization and morphological transformation of intermetallic Al3 Fe, Al6 Mn, and Mg2 Si phases are revealed and discussed in terms of the variation in chemical composition. Following a homogenization heat-treatment, the effect of heat treatment on the intermetallic compounds is also investigated after hot-rolling. It was revealed that the Mg2 Si phase can be broken into small particles and spherodized more easily than the Al3 Fe intermetallic phase during the hot-rolling process. For the Mn containing alloys, both yield and ultimate tensile strength of the hot-rolled alloys increased from 270 to 296 MPa while elongation decreased from 17 to 13%, which can be attributed to Mn-containing intermetallic as well as dispersoid.
    Źródło:
    Archives of Metallurgy and Materials; 2020, 65, 4; 1255-1259
    1733-3490
    Pojawia się w:
    Archives of Metallurgy and Materials
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Optical Properties of Multi-Stacked InAs Quantum Dots Embedded in GaAs/InGaAs Strained Layer and its Annealing Behaviors
    Autorzy:
    Kim, D.
    Kim, G.
    Jeon, S.
    Cho, M.
    Choi, H.
    Kim, M.
    Lee, D.
    Kim, J.
    Eom, G.
    Leem, J.
    Powiązania:
    https://bibliotekanauki.pl/articles/1537752.pdf
    Data publikacji:
    2010-06
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    78.67.Hc
    78.55.Cr
    81.05.Ea
    Opis:
    Multi-stacked InAs QDs embedded in ten periods of GaAs/$In_{0.1}Ga_{0.9}As$ strained layers were grown by MBE and their optical properties were investigated by using PL spectroscopy. For the QDs embedded in ten periods of GaAs/$In_{0.1}Ga_{0.9}As$ strained layers, the PL intensity is enhanced about 4.7 times and a narrower FWHM of 26 meV is observed compared to those of the conventional multi-stacked QDs. The PL spectra of the InAs QDs show blue-shifts of about 50 meV with increasing annealing temperature up to 850°C. At annealing temperature of 600°C, the FWHM of the PL peak is reduced to 16 meV and PL intensity is enhanced compared to those of the as-grown sample, which indicates improvement of size uniformity and crystal quality of the QDs.
    Źródło:
    Acta Physica Polonica A; 2010, 117, 6; 941-944
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Argon Plasma in a New Process for Improving the Physical and Anti-bacterial Properties of Crosslinked Cotton Cellulose with Dimethyloldihydroxyethyleneurea-Maleic Acid
    Zastosowanie plazmy niskotemperaturowej w środowisku argonu w procesie obróbki tkanin bawełnianych sieciowanych za pomocą kwasu dimetylodihydroxyetylenourylomaleinowego dla polepszenia właściwosci fizycznych oraz antybakteryjnych
    Autorzy:
    Tsou, C H
    Suen, M C
    Tsou, C Y
    Chen, J C
    Yeh, J T
    Lin, S M
    Lai, Y C
    Hwang, J Z
    Huang, S H
    Hung, W S
    Hu, C C
    Lee, K R
    Lai, J Y
    Powiązania:
    https://bibliotekanauki.pl/articles/232331.pdf
    Data publikacji:
    2015
    Wydawca:
    Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
    Tematy:
    cotton
    plasma
    antibacterial
    crosslinking
    crosslink length
    crosslinks number per anhydroglucose
    surface distribution
    odour absorption
    bawełna
    plazma
    właściwości antybakteryjne
    sieciowanie tkanin bawełnianych
    kwas dimetylodihydroxyetylenourylomaleinowy
    odporności na zagniecenia
    pochłanianie zapachów
    żywica termoutwardzalna
    Opis:
    This study reports the findings of an argon (Ar) plasma treatment added to the traditional pad-dry-cure process between dry and cure treatments. This new process is called the "paddry-plasma-cure process". The crosslinking agent was a mixture of dimethyloldihydroxyethyleneurea (DMDHEU) and maleic acid (MA). Results show that Ar plasma treatment can increase the bonded crosslinking agent (i.e., the nitrogen content). The dry crease recovery angle (DCRA), wet crease recovery angle (WCRA), and tensile strength retention (TSR) of the pad-dry-plasma-cure finished fabrics were higher than those of traditional pad-dry-cure finished fabrics at a given nitrogen content. Additionally it was found that the number of crosslinks per anhydroglucose unit (CL/AGU) and the length of crosslinks of pad-dry-plasma-cure-finished fabrics were higher than that of traditional pad-dry-cure finished fabrics at the same resin concentration in the pad bath. DCRA, WCRA and TSR values of pad-dry-plasma-cure-finished fabrics were higher than those of pad-dry-curefinished fabrics at the same CL/AGU value. However, activation energies for the pad-dryplasma-cure process were higher than those for the pad-dry-cure process. The anti-bacterial ability and odour absorption of the pad-dry-plasma-cure and pad-dry-plasma-cure finished fabrics were higher than those for the pad-dry-cure finished fabrics. The surface distribution of crosslinking agents for the pad-dry-plasma-cure process was higher than that of the pad-dry-cure process. Thus the pad-dry-plasma-cure process is excellent for improving the physical properties, bacterial inhibition, and odour absorption of finished cotton fabrics and for decreasing their formaldehyde release.
    Artykułu odnosi się do problematyki możliwości i celowości wprowadzenia modyfikacji plazmowej w warunkach niskociśnieniowych i w środowisku argonu do konwencjonalnego procesu wykończenia przeciw mnącego z zastosowaniem reaktywnych żywic termoutwardzalnych. Badano kąt odprężenia na sucho i na mokro, i stwierdzono polepszenie właściwości odporności na zagniecenia w wyniku dodatkowego zastosowania plazmy. Badano również właściwości antybakteryjne i pochłanianie zapachów, które okazały się korzystniejsze dla dodatkowej obróbki plazmowej. W wyniku zmodyfikowanej obróbki uzyskano mniejsze wydzielanie formaldehydu z gotowej tkaniny.
    Źródło:
    Fibres & Textiles in Eastern Europe; 2015, 1 (109); 49-56
    1230-3666
    2300-7354
    Pojawia się w:
    Fibres & Textiles in Eastern Europe
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
      Wyświetlanie 1-79 z 79

      Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies