Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

English (EN)·Polski (PL)·Yкраїнський (UK)
Przejdź do strony domowej biblioteki Centralna Biblioteka Wojskowa Link otwiera się w nowym oknie Logo biblioteki Prolib Integro - strona głównaCentralna Biblioteka Wojskowa

Wyszukujesz frazę "Lee, W-J." wg kryterium: Autor

  Lista filtrów
Wyrównaj
Wyświetlanie 1-15 z 30
Tytuł:
A Study On The Fabrication Of Iron Powder From Forging Scale Using Hydrogen
Próby wytwarzanie proszku żelaza metodą redukcji zgorzeliny pochodzącej z procesów kucia za pomocą wodoru
Autorzy:
Shin, S. M.
Lee, D.-W.
Yun, J.-Y.
Kang, Ch.-Y.
Wang, J.-P.
Powiązania:
https://bibliotekanauki.pl/articles/350946.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
forging scale
hydrogen partial pressure
hematite
iron powder
kucie za pomocą wodoru
hematyt
redukcja zgorzeliny
proszek żelaza
Opis:
This study was conducted to investigate the effect of hydrogen content, temperature, reaction time for the reduction of forging scale which is mainly composed of hematite (Fe2O3). All reductive reactions were performed over the temperature range of 700 to 1200°C as well as 0.1 to 1 atm of hydrogen partial pressures. The results showed that the mechanism for the reduction of iron oxides using hydrogen gas was not a simple process, but proceeded in multiple reduction stages thermodynamically. The iron oxide was almost completely reduced to metallic iron powder with 91 wt.% of iron content in the forging scale at 0.1 atm of hydrogen partial pressure. The content of iron was however found to be increased with increasing hydrogen partial pressure from 0.1 to 1 atm with regardless of temperatures. The metallic iron powder was obtained with the mean size of 100 μm and more porous structure was observed.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1547-1549
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Allometric scaling of marbofloxacin pharmacokinetics: a retrospective analysis
Autorzy:
Yohannes, S.
Hossain, M.A.
Kim, J.Y.
Lee, S.J.
Kwak, D.M.
Suh, J.W.
Park, S.C.
Powiązania:
https://bibliotekanauki.pl/articles/31939.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Opis:
The association between physiologically dependent pharmacokinetic parameters (CLB, T1/2β, Vdss) of marbofloxacin and body weight was studied in eight animal species based on allometric equation Y = aWb, where ‘Y’ is the pharmacokinetic parameter, ‘W’ is body weight, ‘a’ is allometric coefficient (intercept) and ‘b’ is the exponent that describes relation between pharmacokinetic parameter and body weight. The body clearance of marbofloxacin has shown significant (P<0.0001) relation with size (Bwt) in various animal species. However, half-life and volume of distribution were not in association with body weight. Although half-life and volume of distribution were not in a good correlation with body weight, statistically significant association between the body clearance and body weight suggests validity of allometric scaling for predicting pharmacokinetic parameters of marbofloxacin in animal species that have not been studied yet. However further study considering large sample size and other parameters influencing pharmacokinetics of marbofloxacin is recommended.
Źródło:
Polish Journal of Veterinary Sciences; 2014, 17, 1
1505-1773
Pojawia się w:
Polish Journal of Veterinary Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analyzing the factors affecting the safe maritime navigation for training apprentice officers
Autorzy:
Lee, M. K.
Park, S. W.
Park, Y. S.
Park, M. J.
Lee, E. K.
Powiązania:
https://bibliotekanauki.pl/articles/116471.pdf
Data publikacji:
2019
Wydawca:
Uniwersytet Morski w Gdyni. Wydział Nawigacyjny
Tematy:
maritime education and training (MET)
safe maritime navigation
training apprentice officers
simulation based training
ship maneuver simulation
navigational safety
safety at sea
apprentice officer
Opis:
One of the primary factors that affect the safe maritime navigation is the insufficient experience and skill of an apprentice officer, which may be improved using simulation-based training by ensuring operational efficiency. This study aims to determine appropriate factors for achieving effective and intensive simulation-based training of apprentice officers and present the guidelines for such a training scheme. Initially, a marine traffic risk model, which interprets and accurately measures the risk of collision with other vessels, is analyzed to derive the most influential factors in safe navigation. Subsequently, simulation experiments are conducted by applying machine learning to verify the required safe navigation factors for effectively training the apprentice officers. As a result of the above analysis, it was confirmed that the factor affecting safe maritime navigation was the distance from other vessels. Finally, the differences between these distances in the simulations are analyzed for both the apprentice officers and the experienced officers, and the guidelines corresponding to both these cases are presented. This study has the limitation because of the difference between the ship maneuver simulation and the actual ship navigation. This can be resolved based on the results of this study, in combination with the actual navigation data.
Źródło:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation; 2019, 13, 2; 393-399
2083-6473
2083-6481
Pojawia się w:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Argon Plasma in a New Process for Improving the Physical and Anti-bacterial Properties of Crosslinked Cotton Cellulose with Dimethyloldihydroxyethyleneurea-Maleic Acid
Zastosowanie plazmy niskotemperaturowej w środowisku argonu w procesie obróbki tkanin bawełnianych sieciowanych za pomocą kwasu dimetylodihydroxyetylenourylomaleinowego dla polepszenia właściwosci fizycznych oraz antybakteryjnych
Autorzy:
Tsou, C H
Suen, M C
Tsou, C Y
Chen, J C
Yeh, J T
Lin, S M
Lai, Y C
Hwang, J Z
Huang, S H
Hung, W S
Hu, C C
Lee, K R
Lai, J Y
Powiązania:
https://bibliotekanauki.pl/articles/232331.pdf
Data publikacji:
2015
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
cotton
plasma
antibacterial
crosslinking
crosslink length
crosslinks number per anhydroglucose
surface distribution
odour absorption
bawełna
plazma
właściwości antybakteryjne
sieciowanie tkanin bawełnianych
kwas dimetylodihydroxyetylenourylomaleinowy
odporności na zagniecenia
pochłanianie zapachów
żywica termoutwardzalna
Opis:
This study reports the findings of an argon (Ar) plasma treatment added to the traditional pad-dry-cure process between dry and cure treatments. This new process is called the "paddry-plasma-cure process". The crosslinking agent was a mixture of dimethyloldihydroxyethyleneurea (DMDHEU) and maleic acid (MA). Results show that Ar plasma treatment can increase the bonded crosslinking agent (i.e., the nitrogen content). The dry crease recovery angle (DCRA), wet crease recovery angle (WCRA), and tensile strength retention (TSR) of the pad-dry-plasma-cure finished fabrics were higher than those of traditional pad-dry-cure finished fabrics at a given nitrogen content. Additionally it was found that the number of crosslinks per anhydroglucose unit (CL/AGU) and the length of crosslinks of pad-dry-plasma-cure-finished fabrics were higher than that of traditional pad-dry-cure finished fabrics at the same resin concentration in the pad bath. DCRA, WCRA and TSR values of pad-dry-plasma-cure-finished fabrics were higher than those of pad-dry-curefinished fabrics at the same CL/AGU value. However, activation energies for the pad-dryplasma-cure process were higher than those for the pad-dry-cure process. The anti-bacterial ability and odour absorption of the pad-dry-plasma-cure and pad-dry-plasma-cure finished fabrics were higher than those for the pad-dry-cure finished fabrics. The surface distribution of crosslinking agents for the pad-dry-plasma-cure process was higher than that of the pad-dry-cure process. Thus the pad-dry-plasma-cure process is excellent for improving the physical properties, bacterial inhibition, and odour absorption of finished cotton fabrics and for decreasing their formaldehyde release.
Artykułu odnosi się do problematyki możliwości i celowości wprowadzenia modyfikacji plazmowej w warunkach niskociśnieniowych i w środowisku argonu do konwencjonalnego procesu wykończenia przeciw mnącego z zastosowaniem reaktywnych żywic termoutwardzalnych. Badano kąt odprężenia na sucho i na mokro, i stwierdzono polepszenie właściwości odporności na zagniecenia w wyniku dodatkowego zastosowania plazmy. Badano również właściwości antybakteryjne i pochłanianie zapachów, które okazały się korzystniejsze dla dodatkowej obróbki plazmowej. W wyniku zmodyfikowanej obróbki uzyskano mniejsze wydzielanie formaldehydu z gotowej tkaniny.
Źródło:
Fibres & Textiles in Eastern Europe; 2015, 1 (109); 49-56
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Compositional Dependence of Hardness of Ge-Sb-Se Glass for Molded Lens Applications
Zależność stężeniowa twardości szkła Ge-Sb-Se do zastosowań na formowane soczewki
Autorzy:
Park, J. K.
Lee, J. H.
Shin, S. Y.
Yi, J. H.
Lee, W. H.
Park, B. J.
Choi, J. H.
Kim, N. Y.
Choi, Y. G.
Powiązania:
https://bibliotekanauki.pl/articles/352228.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
chalcogenide glasses
Ge-Sb-Se glass
infrared lens
molded lens
infrared camera
szkło
Ge-Sb-Se
soczewki formowane
twardość szkła
kamera termowizyjna
Opis:
Chalcogenide glass in the ternary Ge-Sb-Se system is inherently moldable, thus being considered as a strong candidate material for use in infrared-transmitting lens applications from the viewpoint of thermal and mechanical stability. In an effort to experimentally determine compositional region suitable for the molded lens applications, we evaluate its compositional dependence of hardness. Among the constituent atoms, Ge content turns out to exert a most conspicuous correlation with hardness. This phenomenological behavior is then explained in connection with the structural evolution that Ge brings about.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1205-1208
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect Of DyMn Alloy-Powder Addition On Microstructure And Magnetic Properties Of NdFeB Sintered Magnets
Wpływ dodatku proszku DyMn na mikrostrukturę i właściwości magnetyczne spiekanych magnesów NdFeB
Autorzy:
Lee, M.-W.
Dhakal, D. R.
Kim, T. H.
Lee, S. R.
Kim, H. J.
Jang, T. S.
Powiązania:
https://bibliotekanauki.pl/articles/357010.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Nd-Fe-B sintered magnets
DyMn-alloy powder
coercivity
low melting point element
magnesy spiekane
proszek DyMn
koercja
elementy o niskiej temperaturze topnienia
Opis:
Micostructural change and corresponding effect on coercivity of a NdFeB sintered magnet mixed with small amount of DyMn powder was investigated. In the sintered magnet mixed with the DyMn alloy-powder Dy-rich shell was formed at outer layer of the main grains, while Mn was mostly concentrated at Nd-rich triple junction phase (TJP), lowering melting temperature of the Nd-rich phase that eventually improved the microstructural characteristics of the gain boundary phase. The coercivity of a magnet increased more than 3.5 kOe by the mixing of the DyMn alloy-powder.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1407-1409
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Pre-Sintering on the Diffusion Treatment of HRE for Coercivity Enhancement of a NdFeB Sintered Magnet
Autorzy:
Lee, M. W.
Lee, J. K.
Jang, T. S.
Powiązania:
https://bibliotekanauki.pl/articles/355250.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
grain boundary diffusion process
GBDP
NdFeB magnet
coercivity
pre-sintering
Opis:
We investigated the effect of pre-sintering process on the penetration behavior of Dy in a NdFeB sintered magnet which was grain boundary diffusion treated with Cu/Al mixed Dy source. The pre-sintering of a magnet was performed at 900°C in vacuum and then the pre-sintered body was dipped in the solutions of DyH2, DyH2 + Cu, and DyH2 + Al, respectively. The dipped pre-sintered body were then fully sintered 4 hours at 1060°C followed by a subsequent annealing. The pre-sintering apparently improved the diffusivity of Dy atoms. The penetration of Dy into the magnet extended almost to 2,000 μm from the surface, about four times deeper than that of the normally sintered and diffusion treated one, when the DyH2 + Al solution was used as a Dy source. However, the resulting increase of coercivity was about 4 kOe, somewhat lower than that of the normally treated one, mostly due to excessive oxide formation that hindered to make a continuous Nd-rich grain boundary phase and a core-shell type structure.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 2; 597-601
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect Of The Desorption-Recombination Temperature On The Microstructure And Magnetic Properties Of HDDR Processed Nd-Fe-B Powders
Wpływ temperatury desorpcji-rekombinacji na mikrostrukturę i właściwości magnetyczne proszków Nd-Fe-B przetwarzanych metodą HDDR
Autorzy:
Lee, J.-G.
Cha, H.-R.
Liu, S.
Yu, J.-H.
Baek, Y.-K.
Kwon, H.-W.
Powiązania:
https://bibliotekanauki.pl/articles/353723.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Nd-Fe-B
HDDR
permanent magnet
grain boundary
metoda HDDR
magnes trwały
granica ziarna
Opis:
The effect of the desorption-recombination temperature on the microstructure and magnetic properties of hydrogenation-disproportionation-desorption-recombination (HDDR) processed Nd-Fe-B powders was studied. The NdxB6.4Ga0.3Nb20.2Febal (x=12.5-13.5, at.%) casting alloys were pulverized after homogenizing annealing, and then subjected to HDDR treatment. During the HDDR process, desorption-recombination (DR) reaction was induced at two different temperature, 810°C and 820°C. The higher Nd content resulted in enhanced coercivity of the HDDR powder, and which was attributed to the thicker and more uniform Nd-rich phase along grain boundaries. But this uniform Nd-rich phase induced faster grain growth. The remanence of the powder DR-treated at 820°C is higher than that DR-treated at 810°C. In addition, it was also confirmed that higher DR temperature is much more effective to improve squareness.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1499-1501
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication and Characterization of CoCrFeNiMn High Entropy Alloy Powder Processed by Gas Atomization
Autorzy:
Park, T. G.
Lee, S. H.
Lee, B.
Cho, H. M.
Choi, W. J.
Kim, B. S.
Shin, K. S.
Kim, T.-S.
Powiązania:
https://bibliotekanauki.pl/articles/353649.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high entropy alloy
gas atomization
spark plasma sintering
CoCrFeNiMn
Opis:
In this study, precisely controlled large scale gas atomization process was applied to produce spherical and uniform shaped high entropy alloy powder. The gas atomization process was carried out to fabricate CoCrFeNiMn alloy, which was studied for high ductility and mechanical properties at low temperatures. It was confirmed that the mass scale, single phase, equiatomic, and high purity spherical high entropy alloy powder was produced by gas atomization process. The powder was sintered by spark plasma sintering process with various sintering conditions, and mechanical properties were characterized. Through this research, we have developed a mass production process of high quality and spherical high entropy alloy powder, and it is expected to expand applications of this high entropy alloy into fields such as powder injection molding and 3D printing for complex shaped components.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1055-1059
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of a Spherical Titanium Powder by Combined Combustion Synthesis and DC Plasma Treatment
Autorzy:
Choi, S. H.
Ali, B.
Hyun, S. K.
Sim, J. J.
Choi, W. J.
Joo, W.
Lim, J. H.
Lee, Y. J.
Kim, T. S.
Park, K. T.
Powiązania:
https://bibliotekanauki.pl/articles/356067.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
combustion synthesis
DC plasma treatment
titanium powder
3D printing process
combustion parameters
Opis:
Combustion synthesis is capable of producing many types of refractory and ceramic materials, as well as metals, with a relatively lower cost and shorter time frame than other solid state synthetic techniques. TiO2 with Mg as reductant were dry mixed and hand compacted into a 60 mm diameter mold and then combusted under an Ar atmosphere. Depending on the reaction parameters (Mg concentration 2 ≤ α ≤ 4), the thermocouples registered temperatures between 1160°C and 1710°C . 3 mol of Mg gave the optimum results with combustion temperature (Tc) and combustion velocity (Uc) values of 1372°C and 0.26 cm/s respectively. Furthermore, this ratio also had the lowest oxygen concentration in this study (0.8 wt%). After combustion, DC plasma treatment was carried out to spheroidize the Ti powder for use in 3D printing. The characterization of the final product was performed using X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, and N/O analysis.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1057-1062
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of AZ31/CNT Surface Nano-composite by Double-pass Friction Stir Processing
Autorzy:
Kim, J. Y.
Hwang, J.-W.
Kim, H. Y.
Lee, S. M.
Jung, W.-S.
Byeon, J.-W.
Powiązania:
https://bibliotekanauki.pl/articles/355624.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
surface modification
Double-pass Friction Stir Processing
AZ31
composite
CNT
Opis:
Double-pass Friction Stir Processing (FSP) was applied to fabricate an AZ31/CNT nano-composite for surface hardening of lightweight structural components. The effects of double-pass FSP as well as groove depth (i.e., volume fraction of CNT) on the CNT distribution, dynamically recrystallized grain size, and resulting microhardness were studied. Double-pass FSP was performed for the CNT-filled plate-type specimen with different groove depths of 2, 3, and 4 mm. By applying double-pass FSP, the average size of CNT clusters decreased, implying a more homogeneous distribution. Compared with the FSPed specimen without CNT, grain size was refined from 19 μm to 3 μm and microhardness increased from 52 Hv to 83 Hv (i.e., 71% increase).
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1039-1042
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Finite element analysis of three-point bending of a T-beam structural biaxial highly oriented polymer material
Analiza metodą elementów skończonych zginania trójpunktowego belki teowej wykonanej z wysoko zorientowanego dwuosiowo materiału polimerowego
Autorzy:
Wei, C.-L.
Chang, Y.
Lee, Y.-C.
Lee, R.
Luo, T.-W.
Chen, J.-H.
Powiązania:
https://bibliotekanauki.pl/articles/946988.pdf
Data publikacji:
2018
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Chemii Przemysłowej
Tematy:
solid phase processing
highly oriented polymer (HOP)
orthotropic materials
T-beam
three-point bending
finite element
proces w fazie stałej
wysoko zorientowany polimer
materiały ortotropowe
belka teowa
zginanie trójpunktowe
elementy skończone
Opis:
Polymers with biaxial aligned molecular chains are also orthotropic materials, which are characterized by high tensile strength and low shear strength in the length direction. When orthotropic materials are used as structural shapes with poor shear strength, they are likely to undergo premature failure under shear stress. Therefore, in three-point bending, the cross-section of the entire profile not only bears tensile stress and compressive stress in the length direction, but also simultaneously exhibits shear stress. This study analyzes the distribution of tensile stress, compressive stress and shear stress in the length direction of highly oriented polymers (HOP) by finite element analysis to find the most suitable length-to-height ratio for these materials when used as structural shapes. The finite element analysis software, Abaqus, is utilized to simulate HOP T-beam to analyze the load stress of a T-beam. With a fixed cross–section area, as the length of the material changes, its shear strength also changes. Accordingly, the order of occurrence of tensile failure and shear failure can be investigated. The simulation reveals that when the length-to-height ratio is between 4 : 1 and 20 : 1, a zone of stress in which tensile failure and shear failure occur can be found. This result can be exploited in the design and development of structural beam.
Polimery o dwuosiowo zorientowanych łańcuchach makrocząsteczek są materiałami ortotropowymi, wykazującymi dużą wytrzymałość na rozciąganie oraz niewielką wytrzymałość na ścinanie w kierunku długości. Elementy konstrukcyjne wytworzone z materiału ortotropowego o małej wytrzymałości na ścinanie są podatne na przedwczesne uszkodzenie pod wpływem naprężeń ścinających. Przy zginaniu trójpunktowym w przekroju ich profilu występują zarówno naprężenia rozciągające i ściskające w kierunku podłużnym, jak i naprężenia ścinające. Metodą elementów skończonych analizowano rozkład naprężeń rozciągających, ściskających i ścinających w kierunku podłużnym wysoko zorientowanych polimerów (HOP) w celu określenia optymalnego stosunku długości do wysokości w kształtach konstrukcyjnych. Do symulacji naprężeń obciążeniowych w zginaniu trójpunktowym belki teowej wykorzystano program komputerowy Abaqus. Stwierdzono, że przy stałej powierzchni przekroju poprzecznego belki jej wytrzymałość na ścinanie zmienia się wraz ze zmianą długości. Badano również kolejność występowania uszkodzeń pod wpływem działania sił rozciągających i ścinających. Symulacja wykazała, że przy stosunku długości do wysokości w zakresie od 4 : 1 do 20 : 1 występuje strefa naprężeń, w której mogą się pojawiać uszkodzenia w wyniku rozciągania lub ścinania. Uzyskane wyniki można wykorzystać w projektowaniu i optymalizacji belek konstrukcyjnych.
Źródło:
Polimery; 2018, 63, 3; 219-223
0032-2725
Pojawia się w:
Polimery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High-temperature Oxidation Behavior and Kinetics of Forged 12Cr-MoVW Steel
Autorzy:
Kim, Y. H.
Oak, J.-J.
Bae, K.-C.
Lee, W-J.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/351450.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ferritic/martensitic stainless steels
forging
oxidation kinetics
oxide layer
Opis:
The oxidation kinetics of forged 12Cr-MoVW steel was investigated in an air (N2+O2) atmosphere at 873-1073 K (Δ50 K) using thermogravimetric analysis. The oxidized samples were characterized using X-ray diffraction, and the surface and cross-sectional morphologies were examined using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. The forged 12Cr-MoVW steel samples exhibited parabolic behavior and a low oxidation rate compared with their as-cast counterparts. A protective oxide layer was uniformly formed at relatively low temperature (≤973 K) for the forged samples, which thus exhibited better oxidation resistance than the as-cast ones. These oxides are considered solid-solution compounds such as (Fe, Cr)2O3.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1099-1104
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Integrated plant and pathogen‘omics approaches to understanding fungal diseases of wheat
Autorzy:
Rudd, J.J.
Lee, W.-S.
Hammond-Kosack, K.
Kanyuka, K.
Powiązania:
https://bibliotekanauki.pl/articles/81017.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
conference
plant infection
fungal disease
wheat
septoria tritici blotch
intercellular pathogen
leaf damage
RNA sequence
functional genomics
Źródło:
BioTechnologia. Journal of Biotechnology Computational Biology and Bionanotechnology; 2013, 94, 3
0860-7796
Pojawia się w:
BioTechnologia. Journal of Biotechnology Computational Biology and Bionanotechnology
Dostawca treści:
Biblioteka Nauki
Artykuł
Wyświetlanie 1-15 z 30

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies