Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Park, S.-H." wg kryterium: Autor


Wyświetlanie 1-32 z 32
Tytuł:
Microstructure and Compression Properties of Fe-Cr-B Alloy Manufactured using Laser Metal Deposition
Autorzy:
Joo, Y.-A.
Yoon, T.-S.
Park, S.-H.
Lee, K.-A.
Powiązania:
https://bibliotekanauki.pl/articles/352075.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Fe-Cr-B composite
laser Metal Deposition
bulk type
microstructure
compressive properties
Opis:
Fe-Cr-B alloy is a material with precipitation of boride inside Fe matrix, and it features outstanding hardness and wear resistance properties. However, Fe-Cr-B alloy is a difficult material to process, making it difficult to use as a bulk type structure material which requires delicate shapes. This study attempted to manufacture Fe-Cr-B alloy using a 3D printing process, laser metal deposition. This study also investigated the microstructure, hardness and compression properties of the manufactured alloy. Phase analysis results is confirmed that α-Fe phase as matrix and (Cr, Fe)2B phase as reinforcement phase. In the case of (Cr, Fe)2B phase, differences were observed according to the sample location. While long, coarse, unidirectional needle-type boride phases (~11 μm thickness) were observed in the center area of the sample, relatively finer boride phases (~6 μm thickness) in random directions were observed in other areas. At room temperature compression test results confirmed that the sample had a compression strength is approximately 2.1 GPa, proving that the sample is a material with extremely high strength. Observation of the compression fracture surface identified intergranular fractures in areas with needle-type boride, and transgranular fractures in areas with random borides. Based on this results, this study also reviewed the deformation behavior of LMD Fe-Cr-B alloy in relation to its microstructures.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1459-1462
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Thermal Conductivity and Microstructure of Copper Coated Graphite Composite by Spark Plasma Sintering Process
Autorzy:
Park, S. H.
Kim, D. B.
Lee, R. G.
Son, I. J.
Powiązania:
https://bibliotekanauki.pl/articles/355632.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
metal matrix composites
thermal conductivity
thermal expansion
interfacial bonding
spark plasma sintering
Opis:
This study focuses on the fabrication of thermal management material for power electronics applications using graphite flake reinforced copper composites. The manufacturing route involved electroless plating of copper in the graphite flake and sintering process are optimized. The microstructures, interface, thermal properties, and relative density of graphite/Cu composites are investigated. The relative density of the composites shows 99.5% after sintering. Thermal conductivities and coefficients of thermal expansion of this composites were 400-480 Wm-1K-1 and 8 to 5 ppm k-1, respectively. Obtained graphite nanoplatelets-reinforced composites exhibit excellent thermo-physical properties to meet the heat dispersion and matching requirements of power electronic devices to the packaging materials.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1303-1306
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Heat Treatment on Microstructure and Impact Toughness of Ti-6Al-4V Manufactured by Selective Laser Melting Process
Autorzy:
Lee, K.-A.
Kim, Y.-K.
Yu, J.-H.
Park, S.-H.
Kim, M.-C.
Powiązania:
https://bibliotekanauki.pl/articles/354570.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
selective laser melting
Ti-6Al-4V
microstructure
impact toughness
heat treatment
Opis:
This study manufactured Ti-6Al-4V alloy using one of the powder bed fusion 3D-printing processes, selective laser melting, and investigated the effect of heat treatment (650°C/3hrs) on microstructure and impact toughness of the material. Initial microstructural observation identified prior-β grain along the building direction before and after heat treatment. In addition, the material formed a fully martensite structure before heat treatment, and after heat treatment, α and β phase were formed simultaneously. Charpy impact tests were conducted. The average impact energy measured as 6.0 J before heat treatment, and after heat treatment, the average impact energy increased by approximately 20% to 7.3 J. Fracture surface observation after the impact test showed that both alloys had brittle characteristics on macro levels, but showed ductile fracture characteristics and dimples at micro levels.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1341-1346
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Fe Content on the Contact Resistance of Electroplated Au-Fe Alloy Layers
Autorzy:
Park, H. S.
Son, I.
Powiązania:
https://bibliotekanauki.pl/articles/352468.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
electroplating
Au-Fe alloy
contact resistance
thermal aging
Opis:
In this study, variations in the contact resistance of electroplated Au-Fe alloy layers with Fe content were investigated. The contact resistance of electroplated Au-Fe alloy layers that were subject to thermal aging at 260°C in the atmosphere, tended to increase significantly with an increase in the Fe content. Through an analysis method employing X-ray photoelectron spectroscopy (XPS/ESCA) and Auger electron spectroscopy (AES), Ni oxides, such as NiO and Ni2O3, on the surface of the thermally aged electroplated Au-Fe alloy layers were observed. It is believed that the Ni oxide existing on the surface diffused from the underlying electroplated Ni layers to the surface through the grain boundaries in the electroplated Au-Fe layers during the thermal aging. As the Fe content in the electroplated Au-Fe layers increased, the grain size decreased. As the grain size decreases, more Ni oxide was detected on the surface. Therefore, with a rise in the Fe content, more Ni diffuses to the surface via grain boundaries, and more Ni oxide is formed on the surface of the electroplated Au-Fe layers, increasing the contact resistance of the electroplated Au-Fe alloy layers.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1503-1507
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison Of Mercury Distribution Between The Types Of Spent Fluorescent Lamp
Porównanie dystrybucji rtęci pomiędzy rodzajami zużytych świetlówek
Autorzy:
Rhee, S. W.
Park, H. S.
Choi, H. H.
Powiązania:
https://bibliotekanauki.pl/articles/356384.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
spent fluorescent lamp
types
phosphor powder
mercury distribution
świetlówki
luminofory
dystrybucja rtęci
Opis:
Spent fluorescent lamps(SFLs) such as linear type lamp, compact type lamp and U-type lamp are used to estimate mercury distribution in the components of lamps. Determination of mercury concentration in the components of spent fluorescent lamp is performed by the DMA method. Mercury concentration in the components of spent fluorescent lamp can be varied with the manufactures of lamp. Mercury portion in phosphor powder and glass from any types of spent fluorescent lamp is estimated to be higher than 99% by the analysis of mercury distribution. Through mercury distribution in the components for SFLs, the mercury concentration in phosphor powder is much higher than that in other components regardless of the type of lamp. Hence, it is desirable that phosphor powder of spent fluorescent lamps should be controlled separately and safely.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1297-1299
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Two-Dimensional Automatic Control Modeling of a Posture Control System
Autorzy:
Park, K. S.
Kim, U. H.
Powiązania:
https://bibliotekanauki.pl/articles/90283.pdf
Data publikacji:
1998
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
posture control model
posturography
perturbation
parameter identification
model fitness
stability
predictability
model kontroli
postura
posturografia
identyfikacja parametrów
fitness
Opis:
A posture control model has been developed on the basis of the 2-dimensional feedback control theory. Human postural characteristics were investigated in 5 healthy participants. Tests were performed with eyes open and eyes closed. After 5 s of quiet standing, each participant was unexpectedly pulled forward by 30 mm at his pelvis height and then released. Postural sway was measured over 20 s at a rate of 100 per second. Transfer functions to represent the posture control characteristic were identified by the least squares' method. These showed good results of the model's fitness, predictability, and stability. The response of the eyes-closed condition to perturbation is more oscillatory than that of the eyes-open condition. It seems that the model identified could be applicable to ergonomics, sports, or clinical situations.
Źródło:
International Journal of Occupational Safety and Ergonomics; 1998, 4, 4; 485-498
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Error reduction of the Doppler lidar signal using a re-normalization method
Autorzy:
Park, N G
Baik, S H
Park, S K
Kim, D L
Kim, D. H.
Powiązania:
https://bibliotekanauki.pl/articles/173914.pdf
Data publikacji:
2014
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
injection-seeded laser
Doppler lidar
frequency locking
wind lidar
Doppler velocity measurement
Opis:
In this paper, we present a re-normalization method for a Doppler signal of a Doppler lidar system. For the Doppler lidar system, we used an injection-seeded pulsed Nd:YAG laser as a transmitter and an iodine cell as a Doppler frequency discriminator. A frequency locking system that uses the absorption feature of iodine gas is too sensitive to the external or internal noises (iodine cell temperature instability, laser frequency fluctuation, environmental noises, etc.) to maintain its locking point ideally, and this frequency locking error makes the Doppler lidar system acquire the noises as the Doppler frequency shifts. To reduce the Doppler signal error induced by a frequency locking error, we used a re-normalization method by an addition of a laser beam path separated from a transmitter to the Doppler frequency discriminator for re-normalization. In this method, fluctuations of the Doppler signal were reduced using the reference signal. The reduced amount of standard deviation between the Doppler signal and the re-normalization signal was 4.838×10–3 and the Doppler signals showed a 53.3% fluctuation reduction of the averaged error value by this method.
Źródło:
Optica Applicata; 2014, 44, 1; 103-111
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Enhancement of Life Time of the Dimensionally Stable Anode for Copper Electroplating Applications
Autorzy:
Son, S. H.
Park, S. C.
Lee, M. S.
Powiązania:
https://bibliotekanauki.pl/articles/356684.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
dimensionally stable anode
surface treatment
life time
copper
electrodeposition
Opis:
In order to enhance the long-term stability of DSA for copper electroplating process, in the present study, noble metal oxides with excellent electrochemical properties was used and optimum condition was determined the ratio of noble metal oxides, surface pre-treatment of titanium substrate and heat treatment. The effect of the surface pretreatment of titanium substrate and ratio of noble metal oxides were estimated by accelerated test at the highly current density conditions. The lifetime of DSA increase six-fold higher as the oxide thickness of Ta 7 : Ir 3 composition ratio. Under the optimal condition, surface pretreatment led to dramatic increase in the lifetime of DSA.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1019-1022
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of Mo-Si-B Intermetallic Compound Powders Under Different Heat Treatment Conditions
Autorzy:
Park, J. H.
Lee, S.
Kim, D.
Kim, Y.
Yang, S. H.
Lee, S. H.
Powiązania:
https://bibliotekanauki.pl/articles/353369.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Mo-Si-B alloys
intermetallic compounds
reitveld refinement
T2 phase
A15 phase
Opis:
In this research, we investigated the effects of reduction atmospheres on the creation of the Mo-Si-B intermetallic compounds (IMC) during the heat treatments. For outstanding anti-oxidation and elevated mechanical strength at the ultrahigh temperature, we fabricated the uniformly dispersed IMC powders such as Mo5SiB2 (T2) and Mo3Si (A15) phases using the two steps of chemical reactions. Especially, in the second procedure, we studied the influence of the atmospheres (e.g. vacuum, argon, and hydrogen) on the synthesis of IMCs during the reduction. Furthermore, the newly produced IMCs were observed by SEM, XRD, and EDS to identify the phase of the compounds. We also calculated an amount of IMCs in the reduced powders depending on the atmosphere using the Reitveld refinement method. Consequently, it is found that hydrogen atmosphere was suitable for fabrication of IMC without other IMC phases.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1509-1512
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Growth of NdBa$\text{}_{2}$Cu$\text{}_{3}$O$\text{}_{7-δ}$ Superconducting Thin Films on SrTiO$\text{}_{3}$(100) and LaSrGaO$\text{}_{4}$(100) Substrates
Autorzy:
Park, J.-C.
Ha, D. H.
Kim, I.-S.
Park, Y.K.
Powiązania:
https://bibliotekanauki.pl/articles/1964239.pdf
Data publikacji:
1997-07
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
74.76.Bz
Opis:
NdBa$\text{}_{2}$Cu$\text{}_{3}$O$\text{}_{7-δ}$ superconducting thin films were grown on SrTiO$\text{}_{3}$(100) and LaSrGaO$\text{}_{4}$(100) substrates by off-axis rf sputtering and pulsed laser deposition. The effects of several deposition parameters, e.g. gas pressure, substrate temperature and energy density were studied. Thin films grown by off-axis rf sputtering were highly c-axis oriented, but those by pulsed laser deposition were predominantly a-axis oriented under our deposition conditions. However, the c-axis oriented portion for the films grown by pulsed laser deposition was increased by increasing the temperature above 800°C. T$\text{}_{c(zero)}$ was 87 K and 83 K for the c- and a-axis oriented films respectively. The critical current density of c-axis oriented films was 10$\text{}^{6}$-10$\text{}^{7}$ A/cm$\text{}^{2}$ below 60 K.
Źródło:
Acta Physica Polonica A; 1997, 92, 1; 105-114
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study On The Electro-Refining Of Tin In Acid Solution From Electronic Waste
Badanie elektrorafinacji cyny w roztworze kwasu z e-odpadów
Autorzy:
Son, S. H.
Park, S. C.
Kim, J. H.
Kim, Y. H.
Lee, M. S.
Ahn, J.-W.
Powiązania:
https://bibliotekanauki.pl/articles/352665.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
electrorefining
tin
electronic waste
recycling
high purity
elektrorafinacja
cyna
odpady elektroniczne
recykling
Opis:
The tin metal could be retractable from wasted tin scrap, sludge, and wasted electroplated solution hydrometallurgical treatment, and purification process. In order to be used as resource of electronic devices, the retracted crude metal should be purified to the extent of higher than 99.9%. In this study, tin electro-refining process was performed to purify the casted tin crude metal at various experimental conditions: at the current density of 3, 5A/dm2, and in various electrolytes such as hydrochloric acid, sulfuric acid and methansulfonic acid. Additional experiment was conducted using Rotating Disk Electrode (RDE) in order to investigate the rate determining step of tin electro-refining process. The current efficiency, 65.6%, was achievable at the condition of current density, 5A/dm2, and in the electrolyte of Hydrochloric acid. During tin electro-refining process, impurity dissolved from tin crude metal into the electrolyte was analyzed using Inductively Coupled Plasma Optical Emission Spectrometer (ICP-OES), and the result showed the concentration of impurity metal gradually increased. Quantitative analysis on casted tin crude metal showed that it consists of tin with 93.9 wt.% and several impurity metals of Ag, Bi, Pb, Cu, and etc. After tin electro-refining process, the purity of tin increased up to 99.985 wt.%.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1217-1220
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High Temperature Oxidation Property of SiC Coating Layer Fabricated by Aerosol Deposition Process
Autorzy:
Ham, G.-S.
Kim, S.-H.
Park, J.-Y.
Lee, K.-A.
Powiązania:
https://bibliotekanauki.pl/articles/352142.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
silicon carbide
aerosol deposition
coating
high temperature oxidation
Opis:
This study investigated the high temperature oxidation property of SiC coated layer fabricated by aerosol deposition process. SiC coated layer could be successfully manufactured by using pure SiC powders and aerosol deposition on the Zr based alloy in an optimal process condition. The thickness of manufactured SiC coated layer was measured about 5 μm, and coating layer represented high density structure. SiC coated layer consisted of α-SiC and β-SiC phases, the same as the initial powder. The initial powder was shown to have been crushed to the extent and was deposited in the form of extremely fine particles. To examine the high temperature oxidation properties, oxidized weight gain was obtained for one hour at 1000°C by using TGA. The SiC coated layer showed superior oxidation resistance property than that of Zr alloy (substrate). The high temperature oxidation mechanism of SiC coated layer on Zr alloy was suggested. And then, the application of aerosol deposited SiC coated layer was also discussed.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1347-1351
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Range resolution improvement of range-gated vision system in backscattering hazy environments
Autorzy:
Park, S.-K.
Choi, I.-Y.
Baik, S.-H.
Jeong, K.-M.
Powiązania:
https://bibliotekanauki.pl/articles/174523.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
range-gated vision system
range image
windowed center-of-mass
cross-correlation
Gaussian window
Opis:
A range-gated vision system simultaneously provides two-dimensional and range images because its light intensity contains the reflectance as well as depth information. The range-resolution of the system is usually inversely proportional to the induced backscattering noise. In this paper, a range imaging technique is proposed to precisely measure range information from highly backscattering foggy environments. A windowed center-of-mass position extracted from the peak area of a cross-correlation signal of two signals, a Gaussian window signal in reduced size and a range-gated signal according to distance, is adopted as the range depth. The proposed measuring technique provides more robust and more precise range information than conventional measuring techniques for hazy targets by virtue of the reduction of backscattering bias noise usually induced by airborne particles. The experimental results and the signal processing procedures to acquire precise range information from hazy targets are described in this paper.
Źródło:
Optica Applicata; 2017, 47, 4; 533-543
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure Evolution of Ni-Based ODS Superalloy Powders During Horizontal Rotary Ball Milling
Autorzy:
Lee, H.-E.
Kim, Y. S.
Park, J. K.
Oh, S.-T.
Powiązania:
https://bibliotekanauki.pl/articles/355552.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high energy ball milling
Ni-base ODS superalloy
particle and crystalline size
microstructure
Opis:
Microstructure evolution of Ni-based oxide dispersion-strengthened alloy powders with milling time is investigated. The elemental powders having a nominal composition of Ni-15Cr-4.5Al-4W-2.5Ti-2Mo-2Ta-0.15Zr-1.1Y2O3 in wt % were ball-milled by using horizontal rotary ball milling with the change of milling velocity. Microstructure observation revealed that large aggregates were formed in the early stages of ball milling, and further milling to 5 h decreased particle size. The average crystalline size, estimated by the peak broadening of XRD, decreased from 28 nm to 15 nm with increasing milling time from 1 h to 5 h. SEM and EPMA analysis showed that the main elements of Ni and Cr were homogeneously distributed inside the powders after ball milling of 5 h.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1253-1255
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The High Temperature Oxidation Stability of STS434L/Silicon Oxide Compacts
Autorzy:
Park, J. W.
Ko, B. H.
Jung, W. Y.
Park, D. K.
Ahn, I. S.
Powiązania:
https://bibliotekanauki.pl/articles/352481.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high-temperature oxidation stability
metallic oxide
densification
Opis:
In order to improve the high-temperature oxidation stability, a study of 434L sintered stainless steel was focused on the effect of addition of metallic oxides to form stable oxide film on the inner particle surface. In this paper, oxidation behavior of 434L compacted parts in accordance with the addition of metallic oxides were discussed with high temperature oxidative reaction, and sintering behavior analysis under 950°C. Oxidation weight gains of 434 L have increased as a form of parabolic laws. The hightemperature oxidation resistance was improved by the mixed addition of amorphous SiO2 and silica up to 2wt.%. The oxidation rate was decreased and kept constant after 60 hours. It was caused by the restraint succeeding oxidation due to the stable oxide formation of Cr2SiO4 phases on the particle surface to prevent densification and inhibition the external diffusion of Cr. High-temperature stability was confirmed by the electrical resistivity maintains the constant value of 1.3×10-2 Ω ·cm when the silica added less than 2w/o to 1w/o A-SiO2 added 434L.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 1; 307-313
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Variable-Focus Fluid Lens Using an Electromagnetic Actuator
Autorzy:
Lee, J.
Park, K.
Choi, J.
Kim, H.
Kong, S.
Powiązania:
https://bibliotekanauki.pl/articles/1399681.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
85.85.+j
42.79.Bh
Opis:
A variable-focus fluid lens controlled by an electromagnetic actuator and its characteristics are presented in this paper. The repulsive force between an NdFeB magnet and a solenoid through electromagnetic induction causes deflections in the elastomeric membranes integrated in the lens resulting in a focal-length change. The controllability of the focal length of the fabricated lens with an aperture size of 2 mm was approximately from infinity to 15 mm (with input current of 100 mA). The actuator including the solenoid was carefully designed to avoid thermal crosstalk of the lens fluid and magnet from the electromagnetic induction of the solenoid. The settling time to form a convex shape of the lens membrane was approximately 2.5 ms at an input current of 20 mA.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 202-204
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Surface Characterization of Metallic Fuel Slugs Prepared by Modified Injection Casting
Autorzy:
Mun, S.-U.
Kim, K.-H.
Oh, S.-J.
Park, J.-Y.
Hong, S.-I.
Powiązania:
https://bibliotekanauki.pl/articles/351428.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
sodium-cooled fast reactor
metallic fuel slug
U-Zr alloy
surface characterization
injection casting
Opis:
Metallic fuel slugs containing rare-earth (RE) elements have high reactivity with quartz (SiO2) molds, and a reaction layer with a considerable thickness is formed at the surface of metallic fuel slugs. The surface characterization of metallic fuel slugs is essential for safety while operating a fast reactor at elevated temperature. Hence, it is necessary to evaluate the surface characteristics of the fuel slugs so that chemical interaction between fuel slug and cladding can be minimized in the reactor. When the Si element causes a eutectic reaction with the cladding, it deteriorates the metallic fuel slugs. Thus, it is necessary to examine the characteristics of the surface reaction layer to prevent the reaction of the metallic fuel slugs. In this study, we investigated the metallurgical characteristics of the surface reaction layer of fabricated U-10wt.%Zr-Xwt.%RE (X = 0, 5, 10) fuel slugs using injection casting. The results showed that the thickness of the surface reaction layer increased as the RE content of the metallic fuel slugs increased. The surface reaction layer of the metallic fuel slug was mainly formed by RE, Zr and the Si, which diffused in the quartz mold.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1049-1053
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Biological Evaluation of Anodized Biodegradable Magnesium-Calcium Alloys
Autorzy:
Kim, J.
Lee, J.
Lee, K.
Park, S.
Lim, H.
Park, C.
Bae, J.
Yun, K.
Powiązania:
https://bibliotekanauki.pl/articles/1398763.pdf
Data publikacji:
2016-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
87.85.jj
87.85.J-
Opis:
The objective of this study was to evaluate the biocompatibility of studied binary magnesium-calcium (Mg-Ca) alloys for biodegradable intraosseous implants. Mg is necessary for health and is a non-toxic biodegradable material that decomposes naturally in the body. Nevertheless, Mg has been implicated in problems including diminished physical properties and corrosion resistance when degradation is too rapid prior to bone healing. This study has explored the effect of Ca on the corrosion resistance and biological evaluation after anodizing treatment with different contents of Ca alloy. Binary Mg-0.5Ca, Mg-1Ca and Mg-5Ca alloys were prepared by the casting method under an argon atmosphere and cut into disc-shaped pieces. Pure Mg alloy was used as the control. Anodic oxidation was performed for 15 minutes at a voltage of 120 V using an electrolyte solution containing Ca gluconate, sodium hexametaphosphate, and sodium hydroxide at room temperature. Corrosion resistance was analyzed using a corrosion tester. After a hydrogen evolution test, the surface pattern and phase changes were observed on a scanning electron microscop (SEM) and energy dispersive spectroscop (EDS). Microscopic evaluation of the adhesion and cell biological functions of Mg was conducted by observing the response of human fetal osteoblastic 1.19 cells with regard to changes in surface film properties, depending on the amount of Ca. Our results support the view that in Mg-xCa alloys (x=0.5, 1, 5 wt.%) treated using anodic oxidation, the increasing Ca content controls the rate of decomposition and improves corrosion resistance.
Źródło:
Acta Physica Polonica A; 2016, 129, 4; 728-735
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of Surface Characteristics and Physical Properties on Biodegradable Magnesium-Calcium Alloys by Anodic Oxidation
Autorzy:
Kim, J.
Lee, J.
Yang, H.
Park, S.
Lim, H.
Oh, G.
Yun, K.
Powiązania:
https://bibliotekanauki.pl/articles/1191716.pdf
Data publikacji:
2016-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
87.85.jj
87.85.jc
Opis:
The purpose of this study was to determine the effect of calcium (Ca) on the surface characteristics and physical properties of magnesium-calcium alloys after anodization. A novel binary alloy Mg-xCa (in which x=0.5, 1, or 5 wt.%) was cast by combining magnesium (99.9%) and calcium (99.9%) in an argon gas (99.99%) atmosphere. A magnesium alloy rod having a diameter of 15 mm was cut into discs, each 2 mm thick. The specimens were subjected to anodic oxidation at 120 V for 15 minutes at room temperature in an electrolyte solution consisting of calcium gluconate, sodium hexametaphosphate, and sodium hydroxide. Surface and cross-sectional morphological changes were observed using scanning electron microscopy, and the microstructures and phases were detected by means of X-ray diffraction. Hardness and surface roughness were assessed by means of a Vickers hardness tester and a surface roughness meter, respectively. The results show that the physical properties of these magnesium-calcium alloys have been improved, because it was possible to control the dissolution rate according to the amount of calcium added.
Źródło:
Acta Physica Polonica A; 2016, 129, 4; 736-741
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Isotopic water separation using AGMD and VEMD
Autorzy:
Kim, J.
Park, S.
Kim, T.-S.
Jeong, D.-Y.
Ko, K.-H.
Powiązania:
https://bibliotekanauki.pl/articles/147314.pdf
Data publikacji:
2004
Wydawca:
Instytut Chemii i Techniki Jądrowej
Tematy:
AGMD
VEMD
oxygen isotopes
PET
FDG
Opis:
The 18O isotopic water permeation and separation characteristics of a hydrophobic PTFE membrane using Air Gap Membrane Distillation (AGMD) and Vacuum Enhanced Membrane Distillation (VEMD) were investigated. Permeation fluxes were measured by weighing the collected membrane-permeated water vapor. 18O/16O of each water sample was analyzed by the Tunable Diode Laser Absorption Spectroscopy (TDLAS). We observed the effects of the air filled membrane pores and the temperature gradient applied to the membrane surfaces on the vapor permeation flux and the oxygen isotope separation for the first time. For both AGMD and VEMD, the permeation flux and the degree of 18O separation increased as the membrane interfacial temperature gradient increased. Even though, oxygen isotope separation and the permeation flux for VEMD is slightly higher than AGMD, the latter may be more efficient from the system's operational point of view.
Źródło:
Nukleonika; 2004, 49, 4; 137-142
0029-5922
1508-5791
Pojawia się w:
Nukleonika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of High-Strength Gray Cast Iron Using Permanent Magnet Scrap
Autorzy:
Park, S.-Y.
Kim, J. H.
Seo, S. J.
On, J. S.
Lim, K. M.
Powiązania:
https://bibliotekanauki.pl/articles/352204.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
gray cast iron
rare earth element
Nd-Fe-B magnet scrap
graphite formation
microstructure
Opis:
In this study, we have developed the manufacturing technology for high strength gray cast irons by using the spent permanent magnet scraps. The cast specimen inoculated by using a spent magnet scraps showed the excellent tensile strength up to 306MPa. This tensile strength value is 50MPa higher than that of the specimen cast without inoculation, and is similar to that of the specimen inoculated by using the expensive misch-metal. These superior mechanical properties are attributed to complex sulfides created during solidification that promote the formation and growth of Type-A graphite. It is therefore concluded that spent magnets scrap can provide an efficient and cost-effective inoculation agent for the fabrication of high-performance gray cast iron.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1113-1117
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Compositional Dependence of Hardness of Ge-Sb-Se Glass for Molded Lens Applications
Zależność stężeniowa twardości szkła Ge-Sb-Se do zastosowań na formowane soczewki
Autorzy:
Park, J. K.
Lee, J. H.
Shin, S. Y.
Yi, J. H.
Lee, W. H.
Park, B. J.
Choi, J. H.
Kim, N. Y.
Choi, Y. G.
Powiązania:
https://bibliotekanauki.pl/articles/352228.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
chalcogenide glasses
Ge-Sb-Se glass
infrared lens
molded lens
infrared camera
szkło
Ge-Sb-Se
soczewki formowane
twardość szkła
kamera termowizyjna
Opis:
Chalcogenide glass in the ternary Ge-Sb-Se system is inherently moldable, thus being considered as a strong candidate material for use in infrared-transmitting lens applications from the viewpoint of thermal and mechanical stability. In an effort to experimentally determine compositional region suitable for the molded lens applications, we evaluate its compositional dependence of hardness. Among the constituent atoms, Ge content turns out to exert a most conspicuous correlation with hardness. This phenomenological behavior is then explained in connection with the structural evolution that Ge brings about.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1205-1208
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Sintering and Microstructures of SUS 316L Powder Produced by 3D Printing Process
Autorzy:
Kim, W. J.
Nguyen, H.-H.
Kim, H. Y.
Nguyen, M.-T.
Park, H. S.
Kim, J.-C.
Powiązania:
https://bibliotekanauki.pl/articles/356018.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stainless steel
3D printing
selective laser sintering
SUS 316L
flake powder
Opis:
Selective laser sintering (SLS) is a type of laminating sintering technique, using CO2 laser with (metal, polymer, and ceramic) powders. In this result, the flake SUS 316L was used to achieve a high porous product, and compare to spherical type. After SLS, the porosity of flake-type sample with 34% was quite higher than that of the spherical-type one that had only 11%. The surface roughness of the flake SLS sample were also investigated in both inner and surface parts. The results show that the deviation of the roughness of the surface part is about 64.40μm, while that of the internal one was about 117.65μm, which presents the containing of high porosity in the uneven surfaces. With the process using spherical powder, the sample was quite dense, however, some initial particles still remained as a result of less energy received at the beneath of the processing layer.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1215-1218
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication and Characterization of CoCrFeNiMn High Entropy Alloy Powder Processed by Gas Atomization
Autorzy:
Park, T. G.
Lee, S. H.
Lee, B.
Cho, H. M.
Choi, W. J.
Kim, B. S.
Shin, K. S.
Kim, T.-S.
Powiązania:
https://bibliotekanauki.pl/articles/353649.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high entropy alloy
gas atomization
spark plasma sintering
CoCrFeNiMn
Opis:
In this study, precisely controlled large scale gas atomization process was applied to produce spherical and uniform shaped high entropy alloy powder. The gas atomization process was carried out to fabricate CoCrFeNiMn alloy, which was studied for high ductility and mechanical properties at low temperatures. It was confirmed that the mass scale, single phase, equiatomic, and high purity spherical high entropy alloy powder was produced by gas atomization process. The powder was sintered by spark plasma sintering process with various sintering conditions, and mechanical properties were characterized. Through this research, we have developed a mass production process of high quality and spherical high entropy alloy powder, and it is expected to expand applications of this high entropy alloy into fields such as powder injection molding and 3D printing for complex shaped components.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1055-1059
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect Of Grain Size On The Mechanical Properties Of Aluminum
Wpływ wielkości ziarna na właściwości mechaniczne aluminium
Autorzy:
Jeong, G.
Park, J.
Nam, S.
Shin, S.-E.
Shin, J.
Bae, D.
Choi, H.
Powiązania:
https://bibliotekanauki.pl/articles/351200.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
nanocrystalline aluminum
grain size
microstructure
mechanical properties
tensile behavior
aluminium
wielkość ziarna
mikrostruktura
rozciąganie
właściwości mechaniczne
Opis:
Although many studies have focused on the unique plastic deformation behavior of nanocrystalline aluminum (e.g., the positive deviation from Hall-Petch relation, the unusual yield-drop phenomenon in tensile mode, etc.), the data reported by different research groups are inconsistent with each other, possibly because of different fabrication processes. In this study, aluminum samples with a wide grain-size spectrum – from a few micrometers down to 100 nanometers – are manufactured by powder metallurgy. The grain size was measured by X-ray diffraction analysis and transmission electron microscope observation. Furthermore, the tensile behavior, which varied according to a grain size, is discussed with a comparison of the theoretical models.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1287-1291
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect Of Ti Powder Addition On The Fabrication Of TiO2 Nanopowders
Wpływ dodatku nanoproszku Ti na zagęszczanie i spiekanie nanoproszków TiO2
Autorzy:
Raihanuzzaman, R. M.
Park, H. Y.
Ghomashchi, R.
Kwon, T. H.
Son, H.-T.
Hong, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/353186.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
TiO2 nanopowder
magnetic pulsed compaction
densification
sintering
nanoproszek Ti
magnetyczne zagęszczanie impulsowe
zagęszczanie
spiekanie
Opis:
Sintered samples of Ti added TiO2 nanopowders were fabricated by combined application of magnetic pulsed compaction (MPC) and sintering. The effect of Ti nano powder on density, shrinkage and hardness of the samples were investigated as part of the study. The optimum processing conditions were found to be around 0.5 GPa MPC pressure and 1450°C sintering temperature, illustrating maximum density, hardness and minimum shrinkage. High pressure compaction using MPC was found to enhance density with increasing MPC pressure up to 0.9 GPa, and significantly reduce the total shrinkage (about 16% in this case) in the sintered bulks compared to other general processes (about 18%). While sintered samples blended with micro Ti showed presence of microstructural cracks, the samples with 1-2% nano Ti had less or no cracks on them. Overall, the inclusion of nano Ti indicated improvement in mechanical properties of TiO2 nanopowders sintered preforms as opposed to micro Ti-added TiO2.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1473-1477
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characterization of Cladding Hull Wastes from Used Nuclear Fuels
Charakterystyka odpadów z okładzin reaktora wodnego ciśnieniowego
Autorzy:
Kang, K. H.
Lee, C. H.
Jeon, M. K.
Han, S. Y.
Park, G. I.
Hwang, S.-M.
Powiązania:
https://bibliotekanauki.pl/articles/357036.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
used nuclear fuels
metal waste
cladding hulls
zircaloy
radioactivity
reaktor wodny ciśnieniowy
odpady metalowe
odpady z okładzin
radioaktywność
Opis:
Used cladding hulls from pressurized water reactor (PWR) are characterized to provide useful information for the treatment and disposal of cladding hull wastes. The radioactivity and the mass of gamma emitting nuclides increases with an increase in the fuel burn-up and their removal ratios are found to be more than 99 wt.% except Co-60 and Cs-137. In the result of measuring the concentrations of U and Pu included in the cladding hull wastes, most of the residues are remained on the surface and the removal ratio of U and Pu are revealed to be over 99.98 wt.% for the fuel burn-up of 35,000 MWd/tU. An electron probe micro-analyzer (EPMA) line scanning shows that radioactive fission products are penetrated into the Zr oxide layer, which is proportional to the fuel burn-up. The oxidative decladding process exhibits more efficient removal ratio of radionuclides.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1199-1203
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Diets supplemented with Mytilus galloprovincialis from polluted and non-polluted waters and their influence on zinc content in liver of rats loaded with cholesterol
Diety z dodatkiem Mytilus galloprovincialis z wód niezanieczyszczonych i zanieczyszczonych oraz ich wpływ na zawartość cynku w wątrobie szczurów obciążonych cholesterolem
Autorzy:
Jesion, I.
Leontowicz, M.
Leontowicz, H.
Kolnierzak, M.
Gralak, M.A.
Park, Y.-S.
Gorinstein, S.
Powiązania:
https://bibliotekanauki.pl/articles/2958.pdf
Data publikacji:
2014
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
animal diet
diet supplementation
Mytilus galloprovincialis
mussel
polluted water
non-polluted water
zinc content
liver
rat
cholesterol
Opis:
Diets supplemented with Mytilus galloprovincialis from polluted and non-polluted waters and their influence on zinc content in liver of rats loaded with cholesterol. Mussels may reflect the environmental problems that the ecosystem faces. Mytilus galloprovincialis is widely used as an indicator of water pollution in biological monitoring studies. These mussels are filter feeders and may accumulate important ecosystem pollutants what in turn may pose a potential risk to other organisms in the food chain. The aim of the study was to determine zinc content in the diets supplemented with mussels from polluted and non-polluted areas and in the livers of rats fed these diets for 30 days. The zinc content in the diets with mussels from contaminated and noncontaminated waters and in rat livers was examined using a flame atomic absorption spectrophotometry (Perkin-Elmer 1100B). The slight increase in zinc content from 73.2 ±1.2 mg/ /kg in ch diet (control with 1% of cholesterol) to 77.2 ±0.5 mg/kg in the diet with mussels from polluted site was found, but zinc content in all diet was within the normal limits reviewed by McDowell (1992) – 40 to 100 ppm. Zinc content in the diet supplemented with mussels from nonpolluted site (73.7 ±3.7 mg/kg) was similar to that found in ch diet. It can be concluded that cholesterol does not affect zinc bioaccumulation. However, prolonged consumption of mussels from contaminated sites may increase accumulation of zinc in the liver of rats.
Diety z dodatkiem Mytilus galloprovincialis z wód niezanieczyszczonych i zanieczyszczonych oraz ich wpływ na zawartość cynku w wątrobie szczurów obciążonych cholesterolem. Małże mogą odzwierciedlać problemy środowiskowe, przed którymi stoi ekosystem. Mytilus galloprovincialis jest szeroko wykorzystywany w biomonitoringu. Małże te są filtratorami i mogą kumulować w tkankach ważne zanieczyszczenia z ekosystemu, co z kolei może stanowić potencjalne zagrożenie dla innych organizmów w łańcuchu troficznym. Celem badania było określenie zawartości cynku w dietach z dodatkiem małży z obszarów niezanieczyszczonych i zanieczyszczonych oraz w wątrobach szczurów żywionych tymi dietami przez 30 dni. Zawartość cynku w dietach z małżami z zanieczyszczonych i niezanieczyszczonych wód i wątrobach szczurów oznaczono metodą płomieniowej absorpcji atomowej (Perkin-Elmer 1100B). Wykazano nieznaczny wzrost zawartości cynku w diecie z małżami z wód zanieczyszczonych (77,2 ±0,5 mg/kg) względem grupy ch – kontrola z 1% udziałem cholesterolu (73,2 ±1,2 mg/kg), ale zawartość cynku we wszystkich dietach mieściła się w granicach normy podanych przez McDowell (1992) – 40–100 ppm. Zawartość cynku w diecie z małżami z obszarów niezanieczyszczonych (73,7 ±3,7 mg/kg) była zbliżona do zawartości w diecie grupy ch. Podsumowując wyniki, można stwierdzić, że cholesterol nie wpływa na bioakumulację cynku. Jednak, długotrwałe spożywanie małży z wód zanieczyszczonych może zwiększyć akumulację cynku w wątrobie szczurów.
Źródło:
Annals of Warsaw University of Life Sciences - SGGW. Animal Science; 2014, 53
1898-8830
Pojawia się w:
Annals of Warsaw University of Life Sciences - SGGW. Animal Science
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Carbon Co-Deposition During Gas Reduction of Water-Atomized Fe-Cr-Mo Powder
Autorzy:
Ali, B.
Choi, S. H.
Seo, S. J.
Maeng, D. Y.
Lee, C. G.
Kim, T. S.
Park, K. T.
Powiązania:
https://bibliotekanauki.pl/articles/352709.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
water atomization
Fe-based powder
oxide reduction
powder metallurgy
sinter-hardening alloys
Opis:
The water atomization of iron powder with a composition of Fe-3Cr-0.5Mo (wt.%) at 1600°C and 150 bar creates an oxide layer, which in this study was reduced using a mixture of methane (CH4) and argon (Ar) gas. The lowest oxygen content was achieved with a 100 cc/min flow rate of CH4, but this also resulted in a co-deposition of carbon due to the cracking of CH4. This carbon can be used directly to create high-quality, sinter hardenable steel, thereby eliminating the need for an additional mixing step prior to sintering. An exponential relationship was found to exist between the CH4 gas flow rate and carbon content of the powder, meaning that its composition can be easily controlled to suit a variety of different applications.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1119-1124
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis And Electrochemical Characteristics Of Mechanically Alloyed Anode Materials SnS2 For Li/SnS2 Cells
Synteza mechaniczna i charakterystyka elektrochemiczna materiałów anodowych SnS2 dla ogniw Li/SnS2
Autorzy:
Hong, J. H.
Liu, X. J.
Park, D. K.
Kim, K. W.
Ahn, H. J.
Ahn, I. S.
Powiązania:
https://bibliotekanauki.pl/articles/356903.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
MA
Li/SnS2 cell
PCA
wet milling process and electrochemical characteristics
ogniwa Li/SnS2
charakterystyka elektromechaniczna
Opis:
With the increasing demand for efficient and economic energy storage, tin disulfide (SnS2), as one of the most attractive anode candidates for the next generation high-energy rechargeable Li-ion battery, have been paid more and more attention because of its high theoretical energy density and cost effectiveness. In this study, a new, simple and effective process, mechanical alloying (MA), has been developed for preparing fine anode material tin disulfides, in which ammonium chloride (AC), referred to as process control agents (PCAs), were used to prevent excessive cold-welding and accelerate the synthesis rates to some extent. Meanwhile, in order to decrease the mean size of SnS2 powder particles and improve the contact areas between the active materials, wet milling process was also conducted with normal hexane (NH) as a solvent PCA. The prepared powders were both characterized by X-ray diffraction, Field emission-scanning electron microscopeand particle size analyzer. Finally, electrochemical measurements for Li/SnS2 cells were takenat room temperature, using a two-electrode cell assembled in an argon-filled glove box and the electrolyte of 1M LiPF6 in a mixture of ethylene carbonate(EC)/dimethylcarbonate (DMC)/ethylene methyl carbonate (EMC) (volume ratio of 1:1:1).
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1191-1194
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Reaction Kinetics and Morphological Study of TiNb2O7 Synthesized by Solid-State Reaction
Autorzy:
Choi, S. H.
Ali, B.
Choi, K. S.
Hyun, S. K.
Sim, J. J.
Choi, W. J.
Joo, W.
Lim, J. H.
Lee, T. H.
Kim, T. S.
Park, K. T.
Powiązania:
https://bibliotekanauki.pl/articles/355326.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
solid state reaction
kinetic analysis
quantitative phase analysis
TiNb2O7 synthesis
Opis:
Although TiNb2O7 is regarded as a material with high application potential in lithium-ion batteries (LIBs) and solid-oxide fuel cells (SOFCs), it has been difficult to find suitable cost-effective conditions for synthesizing it on a commercial scale. In this study, TiNb2O7 compounds were synthesized by a solid state synthesis process. For stoichiometrically precise synthesis of the TiNb2O7 phase, the starting materials, TiO2 and Nb2O5 were taken in a 1:1 molar ratio. Activation energy and reaction kinetics of the system were investigated at various synthesis temperatures (800,1000,1200, and 1400°C) and for various holding durations (1,5,10, and 20 h). Furthermore, change in the product morphology and particle size distribution were also evaluated as a function of synthesis temperature and duration. Additionally, quantitative phase analysis was conducted using the Rietveld refinement method. It was found that increases in the synthesis temperature and holding time lead to increase in the mean particle size from 1 to 4.5 μm. The reaction rate constant for the synthesis reaction was also calculated.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1051-1056
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of a Spherical Titanium Powder by Combined Combustion Synthesis and DC Plasma Treatment
Autorzy:
Choi, S. H.
Ali, B.
Hyun, S. K.
Sim, J. J.
Choi, W. J.
Joo, W.
Lim, J. H.
Lee, Y. J.
Kim, T. S.
Park, K. T.
Powiązania:
https://bibliotekanauki.pl/articles/356067.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
combustion synthesis
DC plasma treatment
titanium powder
3D printing process
combustion parameters
Opis:
Combustion synthesis is capable of producing many types of refractory and ceramic materials, as well as metals, with a relatively lower cost and shorter time frame than other solid state synthetic techniques. TiO2 with Mg as reductant were dry mixed and hand compacted into a 60 mm diameter mold and then combusted under an Ar atmosphere. Depending on the reaction parameters (Mg concentration 2 ≤ α ≤ 4), the thermocouples registered temperatures between 1160°C and 1710°C . 3 mol of Mg gave the optimum results with combustion temperature (Tc) and combustion velocity (Uc) values of 1372°C and 0.26 cm/s respectively. Furthermore, this ratio also had the lowest oxygen concentration in this study (0.8 wt%). After combustion, DC plasma treatment was carried out to spheroidize the Ti powder for use in 3D printing. The characterization of the final product was performed using X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, and N/O analysis.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1057-1062
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-32 z 32

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies