Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Park, J. J." wg kryterium: Autor


Tytuł:
Fabrication and performance of fly ash granule filter for trapping gaseous cesium
Autorzy:
Park, J. J.
Shin, J. M.
Yang, J. H.
Park, G. I.
Powiązania:
https://bibliotekanauki.pl/articles/147633.pdf
Data publikacji:
2015
Wydawca:
Instytut Chemii i Techniki Jądrowej
Tematy:
fabrication
gaseous cesium
granule filters
performance test
pyroprocessing
trapping
Opis:
Although a disk-type fly ash filter has shown a good performance in trapping gaseous cesium, it has difficulty in charging filters into a filter container and discharging waste filters containing radioactive cesium from a container by remote action. To solve the difficulty of the disk-type fly ash filter, five types of granule filters, including a ball type, tube type, and sponge-structure type have been made. Among them, the best filter type was chosen through simple crucible tests. The five types of granule filters packed into containers were loaded into five alumina crucibles of 50 cc. Five grams of CsNO3 was used as a gaseous cesium source. They were then placed in a muffle furnace and heated to 900°C and maintained for 2 hours. After the experiment, the weights of the cesium trapped filters were measured. Among the five types of granule filters, the sponge-structure type granule filter was the best, which has the highest trapping capacity of cesium. Its capacity is 0.42 g-Cs/g-filter. The chosen sponge-structure type granule filters and disk-type filters have been tested using a two-zone tube furnace. Cs volatilization and Cs trapping zones were maintained at 900 and 1000°C, respectively. Sixteen grams of CsNO3 was used as a gaseous cesium source. The cesium trapping profile of the sponge-structure type granule filters was almost similar to that of the disk-type fly ash filters. For both cases, cesium was successfully trapped within the third filter.
Źródło:
Nukleonika; 2015, 60, No. 3, part 2; 565-570
0029-5922
1508-5791
Pojawia się w:
Nukleonika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Enhanced Microwave Absorption of CNT Composites Mixing with Fe3O4 and Carbonyl Iron
Autorzy:
Park, J. H.
Choi, J.
Lee, K.
Park, J.
Song, J. K.
Jeon, E.
Powiązania:
https://bibliotekanauki.pl/articles/351106.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnetic powders
complex permittivity
complex permeability
composite materials
microwave absorption
Opis:
We fabricated two different kinds of composite materials for absorbing microwave in a frequency range of 2 to 18 GHz using coaxial airline and thru-reflect-line (TRL) method. The composite materials having carbon nanotube (CNT) with carbonyl iron (CI) or iron oxide (Fe3 O4 ) were fabricated by mixing each components. Magnetic properties were measured by SQUID equipment. Complex permittivity and complex permeability were also obtained by measuring S-parameters of the toroidal specimen dispersing CI/CNT and Fe3 O4 /CNT into the 50 weight percent (wt%) epoxy resin. The real permittivity was improved by mixing the CNT however, the real permeability was same as pure magnetic powders. The CI/CNT had a maximum value of real permittivity and real permeability, 11 and 1.4 at 10 GHz, respectively. The CNT composites can be adapted to the radar absorbing materials, band width 8-12 GHz.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1513-1516
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Ni Content on the Austenite Stability and Mechanical Properties of Nanocrystalline Fe-Ni Alloy Fabricated by Spark Plasma Sintering
Autorzy:
Park, D.
Oh, S.-J.
Shon, I.-J.
Lee, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/352972.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Fe-Ni alloy
austenite stability
mechanical properties
spark plasma sintering
Opis:
The mechanical behavior and the change of retained austenite of nanocrystalline Fe-Ni alloy have been investigated by considering the effect of various Ni addition amount. The nanocrystalline Fe-Ni alloy samples were rapidly fabricated by spark plasma sintering (SPS). The SPS is a well-known effective sintering process with an extremely short densification time not only to reach a theoretical density value but also to prevent a grain growth, which could result in a nanocrystalline structures. The effect of Ni addition on the compressive stress-strain behavior was analyzed. The variation of the volume fraction of retained austenite due to deformation was quantitatively measured by means of x-ray diffraction and microscope analyses. The strain-induced martensite transformation was observed in Fe-Ni alloy. The different amount of Ni influenced the rate of the strain-induced martensite transformation kinetics and resulted in the change of the work hardening during the compressive deformation.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1477-1480
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Functional Requirements to Support Traffic Organization Service
Autorzy:
Jeong, J.S.
Park, G.K.
Powiązania:
https://bibliotekanauki.pl/articles/117325.pdf
Data publikacji:
2013
Wydawca:
Uniwersytet Morski w Gdyni. Wydział Nawigacyjny
Tematy:
marine traffic
e-navigation
Traffic Organization Service (TOS)
IALA
Opis:
In the era of e‐Navigation, the future VTS is anticipated to play an important role on the enhancement of maritime safety and the efficiency of maritime transport as a key stakeholder of e‐Navigation. The VTS services need the advanced Traffic Organization Service(TOS). In this paper, the VTS functions for TOS is revisited from the reports of IMO e‐Navigation Correspondence Group and IALA VTS Committee. In Korea, the research activities to enhance the existing VTS functions have been conducted. In terms of TOS, some VTS functions have been developed. In conclusion, all the past traffic data and real‐time ship data are required to provide the advanced TOS. For this, the advanced functions to support TOS should be implemented on VTS console.
Źródło:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation; 2013, 7, 1; 115-118
2083-6473
2083-6481
Pojawia się w:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Structural Properties and Mechanical Behavior of the 2 Step-Reinforced Al-Si/SiCp Metal Matrix Composite by Titanium-Fiber
Autorzy:
Oak, J.-J.
Lee, Y. C.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/356010.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
metal matrix composite
sintering
Ti fiber
mechanical properties
diffusion
Opis:
In this study, the newly designed Al-9Si/SiC particles (SiCp) + Ti-fiber (2step-reinforced Al-9Si alloy matrix) metal matrix composites (MMCs) were fabricated by hot-pressing sintering at 560°C. 2step-reinforced Al-based MMCs were characterized by thermal shrinkage, phase transition, microstructure and tensile strength. The addition of Ti-fiber reduced thermal shrinkage was caused by temperature difference in sintering process as well as enhanced assistance for tensile strength and plastic deformation at room temperature. Experimental results reveal that the 2step-reinforcment sintering by ceramic and metal has a significant effect to increase interface bonding in boundary of each component material and the improved mechanical properties were due to the influence of interfacial product by diffusion. Tensile strength and elongation at room temperature by 2step-reinforcement were improved in 19.5% and 26.2% more than those of Al-9Si/SiCp, respectively. Especially, it reveals that diffusion direction may be varied by sintering methods at low temperature in this study.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1089-1097
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Biological Evaluation of Anodized Biodegradable Magnesium-Calcium Alloys
Autorzy:
Kim, J.
Lee, J.
Lee, K.
Park, S.
Lim, H.
Park, C.
Bae, J.
Yun, K.
Powiązania:
https://bibliotekanauki.pl/articles/1398763.pdf
Data publikacji:
2016-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
87.85.jj
87.85.J-
Opis:
The objective of this study was to evaluate the biocompatibility of studied binary magnesium-calcium (Mg-Ca) alloys for biodegradable intraosseous implants. Mg is necessary for health and is a non-toxic biodegradable material that decomposes naturally in the body. Nevertheless, Mg has been implicated in problems including diminished physical properties and corrosion resistance when degradation is too rapid prior to bone healing. This study has explored the effect of Ca on the corrosion resistance and biological evaluation after anodizing treatment with different contents of Ca alloy. Binary Mg-0.5Ca, Mg-1Ca and Mg-5Ca alloys were prepared by the casting method under an argon atmosphere and cut into disc-shaped pieces. Pure Mg alloy was used as the control. Anodic oxidation was performed for 15 minutes at a voltage of 120 V using an electrolyte solution containing Ca gluconate, sodium hexametaphosphate, and sodium hydroxide at room temperature. Corrosion resistance was analyzed using a corrosion tester. After a hydrogen evolution test, the surface pattern and phase changes were observed on a scanning electron microscop (SEM) and energy dispersive spectroscop (EDS). Microscopic evaluation of the adhesion and cell biological functions of Mg was conducted by observing the response of human fetal osteoblastic 1.19 cells with regard to changes in surface film properties, depending on the amount of Ca. Our results support the view that in Mg-xCa alloys (x=0.5, 1, 5 wt.%) treated using anodic oxidation, the increasing Ca content controls the rate of decomposition and improves corrosion resistance.
Źródło:
Acta Physica Polonica A; 2016, 129, 4; 728-735
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Factor Analysis of Safety for Visitors to a Mega-Event
Autorzy:
Kwon, Y. G.
Park, H. J.
Powiązania:
https://bibliotekanauki.pl/articles/90888.pdf
Data publikacji:
2002
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
factor analysis
safety
mega-event
event tourism
czynniki bezpieczeństwa
bezpieczeństwo uczestników imprez
turystyka
Opis:
This paper investigated the safety factors considered by visitors to the Kwangju Biennale 2000 and analyzed the correlation between the safety factors and the demographic characteristics of the visitors. Global tourism increased throughout the 1990s, with the biggest surge occurring in the Asia-Pacific region. Long-distance travel is also increasing, and at a rate faster than the global average. The opportunities for event tourism appear to be strong almost everywhere, even though recessions may have an impact on these destinations. Along with this upward trend, competition for more desirable tourists is also surging (Getz, 1997). Therefore event tourism is appearing as a powerful method in the fierce competition around the tourism industry.
Źródło:
International Journal of Occupational Safety and Ergonomics; 2002, 8, 3; 365-375
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of correlation based dimension reduction methods
Autorzy:
Shin, Y. J.
Park, C. H.
Powiązania:
https://bibliotekanauki.pl/articles/907508.pdf
Data publikacji:
2011
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
analiza korelacyjna
redukcja wymiaru
liniowa analiza dyskryminacji
canonical correlation analysis
dimension reduction
discriminative canonical correlation analysis
linear discriminant analysis
Opis:
Dimension reduction is an important topic in data mining and machine learning. Especially dimension reduction combined with feature fusion is an effective preprocessing step when the data are described by multiple feature sets. Canonical Correlation Analysis (CCA) and Discriminative Canonical Correlation Analysis (DCCA) are feature fusion methods based on correlation. However, they are different in that DCCA is a supervised method utilizing class label information, while CCA is an unsupervised method. It has been shown that the classification performance of DCCA is superior to that of CCA due to the discriminative power using class label information. On the other hand, Linear Discriminant Analysis (LDA) is a supervised dimension reduction method and it is known as a special case of CCA. In this paper, we analyze the relationship between DCCA and LDA, showing that the projective directions by DCCA are equal to the ones obtained from LDA with respect to an orthogonal transformation. Using the relation with LDA, we propose a new method that can enhance the performance of DCCA. The experimental results show that the proposed method exhibits better classification performance than the original DCCA.
Źródło:
International Journal of Applied Mathematics and Computer Science; 2011, 21, 3; 549-558
1641-876X
2083-8492
Pojawia się w:
International Journal of Applied Mathematics and Computer Science
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Adsorptive molecularly imprinted composite membranes for chiral separation of phenylalanine
Autorzy:
Shah, N.
Rehan, T.
Park, J. K.
Powiązania:
https://bibliotekanauki.pl/articles/779061.pdf
Data publikacji:
2016
Wydawca:
Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Tematy:
molecularly imprinted composite membranes
Phe imprinted beads
Phe imprinted membranes
ultrafiltration
adsorption selectivity
Opis:
Two types of composite imprinted membranes, i.e., composite membrane comprised of D-Phe imprinted beads and D-Phe imprinted membrane or DCM and composite membrane comprised of L-Phe imprinted beads and L-Phe imprinted membranes or LCM, were synthesized by phase inversion technique after a uniform dispersion of beads within the polymeric solutions using simple physico-mechanical process. The assemblies of the prepared DCM, LCM and control membranes were employed in ultrafiltration for chiral separation of D, L-Phenylalanine racemate solution. DCM and LCM showed an improved adsorption capacity (0.334 mg g-1 and 0.365 mg g-1 respectively), and adsorption selectivity (2.72 and 2.98 respectively). However, the percent rejection of the template and counter enantiomer were lower than that of control membranes. Compared to control membrane, the DCM and LCM showed inverse permselectivity. These composite membranes having better adsorption and separation ability for Phenylalanine racemate solution will be suitable in the future for various other applications.
Źródło:
Polish Journal of Chemical Technology; 2016, 18, 3; 22-29
1509-8117
1899-4741
Pojawia się w:
Polish Journal of Chemical Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analyzing the factors affecting the safe maritime navigation for training apprentice officers
Autorzy:
Lee, M. K.
Park, S. W.
Park, Y. S.
Park, M. J.
Lee, E. K.
Powiązania:
https://bibliotekanauki.pl/articles/116471.pdf
Data publikacji:
2019
Wydawca:
Uniwersytet Morski w Gdyni. Wydział Nawigacyjny
Tematy:
maritime education and training (MET)
safe maritime navigation
training apprentice officers
simulation based training
ship maneuver simulation
navigational safety
safety at sea
apprentice officer
Opis:
One of the primary factors that affect the safe maritime navigation is the insufficient experience and skill of an apprentice officer, which may be improved using simulation-based training by ensuring operational efficiency. This study aims to determine appropriate factors for achieving effective and intensive simulation-based training of apprentice officers and present the guidelines for such a training scheme. Initially, a marine traffic risk model, which interprets and accurately measures the risk of collision with other vessels, is analyzed to derive the most influential factors in safe navigation. Subsequently, simulation experiments are conducted by applying machine learning to verify the required safe navigation factors for effectively training the apprentice officers. As a result of the above analysis, it was confirmed that the factor affecting safe maritime navigation was the distance from other vessels. Finally, the differences between these distances in the simulations are analyzed for both the apprentice officers and the experienced officers, and the guidelines corresponding to both these cases are presented. This study has the limitation because of the difference between the ship maneuver simulation and the actual ship navigation. This can be resolved based on the results of this study, in combination with the actual navigation data.
Źródło:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation; 2019, 13, 2; 393-399
2083-6473
2083-6481
Pojawia się w:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Variable-Focus Fluid Lens Using an Electromagnetic Actuator
Autorzy:
Lee, J.
Park, K.
Choi, J.
Kim, H.
Kong, S.
Powiązania:
https://bibliotekanauki.pl/articles/1399681.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
85.85.+j
42.79.Bh
Opis:
A variable-focus fluid lens controlled by an electromagnetic actuator and its characteristics are presented in this paper. The repulsive force between an NdFeB magnet and a solenoid through electromagnetic induction causes deflections in the elastomeric membranes integrated in the lens resulting in a focal-length change. The controllability of the focal length of the fabricated lens with an aperture size of 2 mm was approximately from infinity to 15 mm (with input current of 100 mA). The actuator including the solenoid was carefully designed to avoid thermal crosstalk of the lens fluid and magnet from the electromagnetic induction of the solenoid. The settling time to form a convex shape of the lens membrane was approximately 2.5 ms at an input current of 20 mA.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 202-204
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Study on the Electrical Characteristics and Oxidation Resistance of the STS434L-High Chrome Powder Green Compact at the High-Temperature
Autorzy:
Park, J. W.
Jung, W. Y.
Park, D. K.
Ahn, I. S.
Powiązania:
https://bibliotekanauki.pl/articles/354543.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stainless steel
fecraloy
oxidation resistance
metallic oxide
Opis:
Metallic oxide layer of heat resistant element contributes to the high-temperature oxidation resistance by delaying the oxidation, and also has positive effect on the electrical resistivity increase. In this study, the green compacts of Fe-Cr-Al powder mixed with STS434L were oxidized at 950°C up to 210 hrs in order to consider the effect of metal oxide on the oxidation and electrical resistance. It exhibited the low oxidation resistance in case of 434L only, however it increased as the amount of Fe-Cr-Al powder in the 434L compact. The higher electrical resistivity was observed at the Fe-Cr-Al compact with and 434L powder. The metal oxides of (Fe0.6C0.4)2O3, Cr2O3, and Fe2O3 contributed to the electrical resistivity, whereas Al2O2 took a role of oxidation resistance.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 1; 431-435
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Causal relationship between supply chain dynamic capabilities, technological innovation, and operational performance
Autorzy:
Ju, K.-J.
Park, B.
Kim, T.
Powiązania:
https://bibliotekanauki.pl/articles/407389.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
supply chain management
dynamic capabilities
supply chain dynamic capabilities
technological innovation
operational performance
Opis:
The aim of this study is to empirically examine the impact of supply chain dynamic capabilities on operational performance, and the mediating effect of technological innovation between dynamic capabilities and operational performance. This study is based on empirical data collected from a survey of 206 small- and medium-size firms in Korea. Structural equation modeling is used to test the research questions. The results show that supply chain dynamic capabilities positively influence technological innovation and operational performance of an enterprise. Additionally, structural equation analyses reveal that technological innovation plays a role as a partial mediator of the relationship between supply chain dynamic capabilities and operational performance. In a dynamic and ever-changing environment, the enforcement of dynamic capabilities in a sustainable supply chain is important for the innovation of technology and the improvement of operational performance. Further investigation is required to understand the differences by industries, characteristics of enterprises, and positions in a supply chain.
Źródło:
Management and Production Engineering Review; 2016, 7, 4; 6-15
2080-8208
2082-1344
Pojawia się w:
Management and Production Engineering Review
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Compositional Dependence of Hardness of Ge-Sb-Se Glass for Molded Lens Applications
Zależność stężeniowa twardości szkła Ge-Sb-Se do zastosowań na formowane soczewki
Autorzy:
Park, J. K.
Lee, J. H.
Shin, S. Y.
Yi, J. H.
Lee, W. H.
Park, B. J.
Choi, J. H.
Kim, N. Y.
Choi, Y. G.
Powiązania:
https://bibliotekanauki.pl/articles/352228.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
chalcogenide glasses
Ge-Sb-Se glass
infrared lens
molded lens
infrared camera
szkło
Ge-Sb-Se
soczewki formowane
twardość szkła
kamera termowizyjna
Opis:
Chalcogenide glass in the ternary Ge-Sb-Se system is inherently moldable, thus being considered as a strong candidate material for use in infrared-transmitting lens applications from the viewpoint of thermal and mechanical stability. In an effort to experimentally determine compositional region suitable for the molded lens applications, we evaluate its compositional dependence of hardness. Among the constituent atoms, Ge content turns out to exert a most conspicuous correlation with hardness. This phenomenological behavior is then explained in connection with the structural evolution that Ge brings about.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1205-1208
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Growth of NdBa$\text{}_{2}$Cu$\text{}_{3}$O$\text{}_{7-δ}$ Superconducting Thin Films on SrTiO$\text{}_{3}$(100) and LaSrGaO$\text{}_{4}$(100) Substrates
Autorzy:
Park, J.-C.
Ha, D. H.
Kim, I.-S.
Park, Y.K.
Powiązania:
https://bibliotekanauki.pl/articles/1964239.pdf
Data publikacji:
1997-07
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
74.76.Bz
Opis:
NdBa$\text{}_{2}$Cu$\text{}_{3}$O$\text{}_{7-δ}$ superconducting thin films were grown on SrTiO$\text{}_{3}$(100) and LaSrGaO$\text{}_{4}$(100) substrates by off-axis rf sputtering and pulsed laser deposition. The effects of several deposition parameters, e.g. gas pressure, substrate temperature and energy density were studied. Thin films grown by off-axis rf sputtering were highly c-axis oriented, but those by pulsed laser deposition were predominantly a-axis oriented under our deposition conditions. However, the c-axis oriented portion for the films grown by pulsed laser deposition was increased by increasing the temperature above 800°C. T$\text{}_{c(zero)}$ was 87 K and 83 K for the c- and a-axis oriented films respectively. The critical current density of c-axis oriented films was 10$\text{}^{6}$-10$\text{}^{7}$ A/cm$\text{}^{2}$ below 60 K.
Źródło:
Acta Physica Polonica A; 1997, 92, 1; 105-114
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis and Characterization of a Water-Soluble Ionic Polyacetylene Derivative
Autorzy:
Gal, Y.
Jin, S.
Park, J.
Lim, K.
Powiązania:
https://bibliotekanauki.pl/articles/1398739.pdf
Data publikacji:
2016-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
72.80.L
73.61.P
78.20.C
78.30.J
Opis:
A new water-soluble ionic polyacetylene was synthesized by the acid-catalyzed polymerization of 2-ethynylpyridine using acrylic acid. The polymerization proceeded well to give a high yield of polymer. The acetylenic C ≡ C bond stretching (2110 cm¯¹) and acetylenic ≡ C-H bond stretching (3293 cm¯¹) peaks of 2-ethynylpyridine monomer were not seen in the FT-IR spectrum of polymer. The electro-optical and electrical properties of the ionic polyacetylene were measured and discussed. The resulting polymer showed strong maximum at 513 nm in the UV-Visible absorption, which is corresponding to photon energy of 2.42 eV. The energy gap width of polymer was estimated to be of 2.08 eV. It was observed that the electrochemical process of polymer is reproducible in the potential range of -1.80 to 1.60 V vs Ag/AgNO₃. HOMO and LUMO levels of polymer were 4.85 eV and 2.77 eV, respectively.
Źródło:
Acta Physica Polonica A; 2016, 129, 4; 642-646
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Building of CBR’s DB Using Ontology for a Collision Avoidance System
Autorzy:
Park, G. K.
Kim, W. G.
Benedictos, J.
Powiązania:
https://bibliotekanauki.pl/articles/117348.pdf
Data publikacji:
2008
Wydawca:
Uniwersytet Morski w Gdyni. Wydział Nawigacyjny
Tematy:
anticollision
ontology
Collision Avoidance System
Case Based Reasoning (CBR)
Fuzzy CBR Technique
CBR Data Base
Manoeuvring Situations
Risk of Collision
Opis:
We have proposed Fuzzy-CBR to find a solution from past knowledge retrieved from the database and adapted to the new situation. However, ontology is needed in identifying concepts, relations and instances that are involved in a situation in order to improve and facilitate the efficient retrieval of similar cases from the CBR database. This paper proposes the way to apply ontology for identifying the concepts involved in a new case, used as inputs, for ship collision avoidance support system and in solving for similarity through document articulation and abstraction levels. These ontologies will be used to build a conceptual model of a manoeuvring situation.
Źródło:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation; 2008, 2, 4; 369-374
2083-6473
2083-6481
Pojawia się w:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High-temperature Oxidation Behavior and Kinetics of Forged 12Cr-MoVW Steel
Autorzy:
Kim, Y. H.
Oak, J.-J.
Bae, K.-C.
Lee, W-J.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/351450.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ferritic/martensitic stainless steels
forging
oxidation kinetics
oxide layer
Opis:
The oxidation kinetics of forged 12Cr-MoVW steel was investigated in an air (N2+O2) atmosphere at 873-1073 K (Δ50 K) using thermogravimetric analysis. The oxidized samples were characterized using X-ray diffraction, and the surface and cross-sectional morphologies were examined using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. The forged 12Cr-MoVW steel samples exhibited parabolic behavior and a low oxidation rate compared with their as-cast counterparts. A protective oxide layer was uniformly formed at relatively low temperature (≤973 K) for the forged samples, which thus exhibited better oxidation resistance than the as-cast ones. These oxides are considered solid-solution compounds such as (Fe, Cr)2O3.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1099-1104
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Hafnium and Zirconium to Glass Forming Ability, Thermal Stability, Plasticity Deformation and Crystallization of Ni-Free Pentabasic Ti-Based Bulk Metallic Glasses
Autorzy:
Oak, J.-J.
Kim, Y. H.
Bae, K.-C.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/352087.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ti-based alloy
metallic glass
Ti fiber
glass formability
plastic deformation
Opis:
The newly designed Ti-based bulk metallic glass (BMG) in which case of fracture behavior was observed 1990MPa to compressive strength with a wide plastic deformation around 7% after process of elastic deformation. This phenomenon can be compared with those of Ti-based alloys and other Ti-based BMGs and indicates high potential to be applied in use. It was evaluated the Ti-based BMG for thermal stability that the reduced glass parameters, ΔTx, Trg and γ, are 79K, 0.50 and 0.38, respectively. In addition, it reveals high activation energies for crystallization in which are estimated to Ex1 = 291.77 ±9.71 kJ/mol, Ex2 = 588.77 ±28.88 kJ/mol and Ex3 = 330.26 ±3.61 kJ/mol on kissinger plotting in this study.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1081-1087
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Formation And Stabilization Of Silver Nanoparticles In Ethanol By Phosphinic Acid
Redukcja i stabilizacja nanocząstek srebra w etanolu przez kwas fosforowy
Autorzy:
Kim, J.-K.
Shim, H.-M.
Park, M. J.
Koo, K.-K.
Powiązania:
https://bibliotekanauki.pl/articles/356073.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
silver
nanoparticle
kinetic analysis
phosphinic acid
reduction
srebro
nanocząstki
analiza kinetyczna
kwas fosforowy
redukcja
Opis:
Although phosphinic acid (H3PO2) has a powerful reduction potential, the reduction of silver ions by phosphinic acid salt has not yet been reported. In this work, colloidal silver has successfully synthesized by reducing silver ions in ethanol with phosphinic acid as a reducing agent. The effects of [AgNO3]/[H3PO2] ratios and reaction temperature were considered. Spherical silver nanoparticles with cubic structure were successfully prepared and their diameters were measured to be 8.5±0.9 nm − 11.3±0.2 nm. Half-life analysis showed that the reduction of silver ions proceeded with the reaction order of 1.30 on concentration of phosphinic acid and activation energy of 120.7 kJ/mol.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1293-1296
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Development of Hydrophobic Surgical Forceps using Powder Injection Molding and Surface Treatment
Autorzy:
Park, D. Y.
Park, B. R.
Gal, C. W.
Lin, D.
Han, J. S.
Jeong, M.-S.
Bollina, R.
Hwang, W.
Park, S. J.
Powiązania:
https://bibliotekanauki.pl/articles/352093.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
powder injection molding
hydrophobic
debinding
sintering
surface treatment
Opis:
Hydrophobic surgical forceps of end-effectors for laparoscopic operations or minimally invasive surgery were developed through powder injection molding (PIM) and surface treatment. Processing conditions for mixing, debinding, and sintering were investigated to produce defect-free components. An optimum solid loading was determined by torque rheometry experiments. The optimized processing conditions for debinding and sintering were designed through the measurement of weight loss and shrinkage behavior by thermogravimetric analysis and dilatometry experiments. After producing the surgical forceps based on the optimized processing conditions via PIM, surface treatment was carried out to generate the hydrophobic structure on the surface.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 1; 473-480
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Fe Content on the Microstructure and Mechanical Properties of Ti-Al-Mo-V-Cr-Fe Alloys
Autorzy:
Bae, K.-C.
Oak, J.-J.
Kim, Y. H.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/351896.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ti alloy
near-β titanium alloy
aircraft applications
structural material
landing gear
Opis:
To investigate the effect of Fe content on the correlation between the microstructure and mechanical properties in near-b titanium alloys, the Ti-5Al-5Mo-5V-1Cr-xFe alloy system has been characterized in this study. As the Fe content increased, the number of nucleation sites and the volume fraction of the α phase decreased. We observed a significant difference in the shape and size of the α phase in the matrix before and after Fe addition. In addition, these morphological deformations were accompanied by a change in the shape of the α phase, which became increasingly discontinuous, and changed into globular-type α phase in the matrix. These phenomena affected the microstructure and mechanical properties of Ti alloys. Specimen #2 exhibited a high ultimate tensile strength (1071 MPa), which decreased with further addition of Fe.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1105-1108
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of High-Strength Gray Cast Iron Using Permanent Magnet Scrap
Autorzy:
Park, S.-Y.
Kim, J. H.
Seo, S. J.
On, J. S.
Lim, K. M.
Powiązania:
https://bibliotekanauki.pl/articles/352204.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
gray cast iron
rare earth element
Nd-Fe-B magnet scrap
graphite formation
microstructure
Opis:
In this study, we have developed the manufacturing technology for high strength gray cast irons by using the spent permanent magnet scraps. The cast specimen inoculated by using a spent magnet scraps showed the excellent tensile strength up to 306MPa. This tensile strength value is 50MPa higher than that of the specimen cast without inoculation, and is similar to that of the specimen inoculated by using the expensive misch-metal. These superior mechanical properties are attributed to complex sulfides created during solidification that promote the formation and growth of Type-A graphite. It is therefore concluded that spent magnets scrap can provide an efficient and cost-effective inoculation agent for the fabrication of high-performance gray cast iron.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1113-1117
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Oligonol prevented the relapse of dextran sulfate sodium-ulcerative colitis through enhancing Nrf2-mediated antioxidative defense mechanism
Autorzy:
Kim, K.-J.
Park, J.-M.
Lee, J.-S.
Kim, Y.S.
Kangwan, N.
Han, Y.-M.
Kang, E.A.
An, J.M.
Park, Y.K.
Hahm, K.-B.
Powiązania:
https://bibliotekanauki.pl/articles/69501.pdf
Data publikacji:
2018
Wydawca:
Polskie Towarzystwo Fizjologiczne
Tematy:
ulcerative colitis
inflammatory bowel disease
oxidative stress
oligonol
polyphenol
adaptive response
quinone oxidoreductase
relapse
nuclear factor-kappaB
tumour necrosis factor-alpha
Źródło:
Journal of Physiology and Pharmacology; 2018, 69, 3
0867-5910
Pojawia się w:
Journal of Physiology and Pharmacology
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies