Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "mileage" wg kryterium: Wszystkie pola


Tytuł:
Characteristic features of the process of growth in the mileage of hybrid vehicles
Autorzy:
Prochowski, L..
Powiązania:
https://bibliotekanauki.pl/articles/243461.pdf
Data publikacji:
2018
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
hybrid vehicle
mileage of hybrid vehicle
estimation of mileage growth model
Opis:
For a few years, the sales of motor vehicles with hybrid drive systems (referred to as “hybrid vehicles” or “HVs”) have been rapidly growing. However, there is a lack of information about the intensity of operation of vehicles classified in this category, which is completely new. A calculation procedure has been presented that enabled evaluation of the HV mileage growth rate. An analysis of this rate provides grounds for forecasting the changes that are likely to take place in the fleet of motor vehicles, such as the progress in the process of replacement of conventional vehicles with vehicles with alternative drive systems, and this may be a basis for predicting the reduction in fuel consumption and exhaust emissions. Models of the HV mileage growth process have been defined for three different countries. They indicate high mileage growth rates in the initial period of vehicle operation, e.g. until the fourth year of operation of the Auris H cars. The highest mileage growth rates in this period were observed in the Netherlands and Poland. In Germany, this rate was lower by 41%. Significant differences in the intensity of vehicle operation have been observed between the behaviour of HV owners in the countries under analysis. A considerable drop in the annual HV mileage as early as in the fifth and sixth year of vehicle operation is an alarming signal.
Źródło:
Journal of KONES; 2018, 25, 4; 361-368
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristic features of the relation between motor truck mileage and engine cubic capacity
Autorzy:
Prochowski, L.
Powiązania:
https://bibliotekanauki.pl/articles/245269.pdf
Data publikacji:
2016
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
motor truck
mileage
engine capacity
Opis:
The motor vehicle operation process results in a growth in the vehicle mileage and the rate of this growth is usually characterized by specifying the value of this mileage (in km) calculated per a time unit (month, year, etc.). In this paper, the relation between the specific mileage (km per a time unit) of a motor truck and the engine capacity category has been analysed. Results of calculations based on the observation of the mileage of over 3 600 motor trucks of more than 3 500 kg gross vehicle mass (GVM) have been presented. In the analysis, intervals of equal width were adopted in which the mileage values (in km) were grouped. The percentage of the vehicles whose monthly mileage values belonged to the ith interval was calculated. The resulting set of k discrete values of the percentage of the vehicles with predefined mileage was approximated by a polynomial. The approximation functions are polynomials of the fifth or sixth degree. The curves representing such functions very well describe the distribution of values of the mileage of motor vehicles with engines of over 10000 cm3 capacity. A characteristic feature of the calculated distributions of vehicle mileage values is the fact that the location of the areas of predominating mileage values strongly depend on the engine capacity. The highest values of the monthly mileage of motor trucks with engines of up to 5 000 cm3 capacity do not exceed 9 500 km and increase to 12 500 km for trucks with engines whose capacity exceeds 12 000 cm3. Based on the profiles of the approximation functions, it has been found that the mileage values corresponding to the first mode of these functions decline with increasing engine capacity values. Simultaneously, a decrease can be observed in the percentage of the vehicles with short mileage with a growth in the engine capacity values. Conversely, the motor truck mileage values corresponding to the second mode of the approximation functions markedly increase with growing engine capacity values. An increase can also be seen in the percentage of the trucks with long mileage in the group of vehicles with engines of over 10000 cm3 capacity.
Źródło:
Journal of KONES; 2016, 23, 4; 403-412
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the process of mileage growth during the operation of motor trucks, in several categories of engine cubic capacity
Ocena procesu narastania przebiegu podczas eksploatacji samochodów ciężarowych w kilku kategoriach pojemności silnika
Autorzy:
Prochowski, L.
Powiązania:
https://bibliotekanauki.pl/articles/1365337.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
motor vehicle mileage
motor vehicle operation
motor truck
estimation of motor vehicle mileage
przebieg samochodów
eksploatacja samochodów
samochody ciężarowe
ocena przebiegu samochodów
Opis:
The intensity of use of motor vehicles and the range of the transport jobs performed change during the many-year operation of such vehicles. The changes are introduced in result of ongoing analyses of actual current vehicle operation costs, reliability, and performance characteristics. The changes in the vehicle operation process, taking place with vehicle’s age, were analysed on the grounds of the mileage of over 9 000 motor trucks. The analysis covered a 20-year period of vehicle operation. The analysis results were used to estimate the mathematical models that describe the basic characteristics of the mileage growth process, with changes in these characteristics as observed in the recent years along with an intensive development of the road transport in Poland. Models of vehicle mileage growth have been developed for seven categories of engine cubic capacity. The coefficients of model equations have been given and the accuracy of the mileage values calculated on these grounds has been comprehensively evaluated. The relative measures of the scatter in the mileage values obtained from these models do not exceed 12 % of the average values determined from experimental data. A procedure has been proposed that leads to evaluating the mileage growth process and is based on the experience having already been gained in this field. It has been shown that the mileage growth process is strongly related to the engine cubic capacity. The mileage growth process is an important source of information for the planning of vehicle operation, forecasting of costs, and estimating of exhaust emissions and energy consumption in the whole cycle of operation of motor vehicles by transport companies.
W czasie wieloletniej eksploatacji samochodów zmianie ulega intensywność ich użytkowania oraz zakres realizowanych zadań transportowych. Zmiany te są rezultatem analizy kosztów eksploatacji, niezawodności oraz osiąganych parametrów trakcyjnych. Zmiany w procesie eksploatacji, które zachodzą wraz z wiekiem samochodów, analizowano na podstawie przebiegu prawie 9000 samochodów ciężarowych. Analizowany jest dwudziestoletni okres eksploatacji pojazdów. Rezultaty tej analizy wykorzystano podczas estymacji modeli matematycznych, które opisują zasadnicze cechy procesu narastania wartości przebiegu, pojawiające się w ostatnich latach wraz z intensywnym wzrostem transportu drogowego w Polsce. Opracowano modele narastania przebiegu w siedmiu kategoriach pojemności silnika. Podano współczynniki równań tych modeli oraz dokonano wszechstronnej oceny dokładności obliczonych na ich podstawie wartości przebiegu. Obliczone względne miary rozrzutu wartości przebiegu z tych modeli nie przekraczają 12% od wartości średnich, wyznaczonych z danych eksperymentalnych. Zaproponowano procedurę postępowania, która prowadzi do wyznaczenia oceny procesu narastania przebiegu i jest oparta na dotychczasowych doświadczeniach w tym zakresie. Pokazano, że proces narastania przebiegu ma silny związek z pojemnością silnika. Proces narastania przebiegu jest ważnym źródłem informacji podczas planowania eksploatacji pojazdów, prognozowania kosztów, a także oceny emisji spalin i zużycia energii w całym cyklu eksploatacji samochodów w firmach transportowych.
Źródło:
Eksploatacja i Niezawodność; 2018, 20, 3; 359-370
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of piston surface treatment on piston assembly friction in an eco-mileage vehicle engine
Autorzy:
Nakashima, Kohei
Uchiyama, Yosuke
Powiązania:
https://bibliotekanauki.pl/articles/2097601.pdf
Data publikacji:
2022
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
eco-mileage vehicle engine
floating cylinder liner
fine particle bombarding
piston
piston assembly friction
tłok
tarcie układu korbowego
Opis:
This study investigated the effect on piston assembly friction after treating piston surfaces with a fine particle bombarding process, using a friction measurement apparatus with a floating cylinder liner, similar to an eco-mileage vehicle engine. Friction was measured in four conditions: (1) no treatment (standard piston in a commercially-available engine), (2) micro dimple treatment (45 μm ceramic particles were air-blasted onto the piston surface), (3) molybdenum disulfide (MoS2) shot treatment (1 μm MoS2 particles were air-blasted onto the piston surface), and (4) combination of the previous two micro dimple and MoS2 shot treatments (first 45 μm ceramic particles and then 1 μm MoS2 were air-blasted onto the piston surface). Results indicated that friction decreased in the following order: no treatment > micro dimple treatment > MoS2 shot treatment > combination of micro dimple and MoS2 shot treatments.
Źródło:
Combustion Engines; 2022, 61, 1; 18--23
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental development of apparatus to measure piston assembly friction in an eco-mileage vehicle engine
Autorzy:
Nakashima, Kohei
Uchiyama, Yosuke
Powiązania:
https://bibliotekanauki.pl/articles/133190.pdf
Data publikacji:
2019
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
eco-mileage vehicle engine
floating cylinder liner
piston assembly friction
piston ring
piston skirt
tarcie układu korbowego
pierścień tłokowy
płaszcz tłoka
Opis:
Apparatus was developed to measure piston assembly friction with a floating cylinder liner against crank angle, using components of an eco-mileage vehicle engine as much as possible. This apparatus was then used to investigate the effect of different sets of piston rings on piston assembly friction in an eco-mileage vehicle engine. Results indicated that, compared to the piston with all three rings (a top ring, a second ring and an oil ring), the piston with two rings (a top ring and an oil ring) reduced piston assembly friction at all engine temperatures and engine speeds. Another configuration of two rings, with the top ring and the second ring, but without the oil ring, reduced friction at a lower engine temperature and speed, but was almost the same as the three-ring set at a higher engine temperature and speed. Finally, a one-ring set, with only the top ring, further reduced friction, except at a higher temperature and speed, where friction was greater than the two-ring set without the second ring.
Źródło:
Combustion Engines; 2019, 58, 2; 55-59
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison of mileage fuel consumption with the natural operation of the three different cycles
Autorzy:
Sitnik, L. J.
Magdziarz-Tokłowicz, M.
Walkowiak, Wł.
Wróbel, R.
Włostowski, R.
Powiązania:
https://bibliotekanauki.pl/articles/243579.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
fuel consumption
mileage fuel consumption
resistance to motion
energy consumption of traffic
vehicle operation
SI engine
Opis:
In the automotive industry in the world continuously being sought universal driving cycle. The test should closely match the fuel consumption and emissions of toxins in the fumes of the test vehicle in its real operating conditions [4]. However, in the previously developed solid driving tests established velocity profiles differ significantly from actual driving conditions. The difference in fuel consumption, comparing the natural operation of the NEDC test reaches an average of 18%. The new version of the driving cycle should be more realistic to the everyday use of additional equipment and gadgets that are installed in modern vehicles [1]. The impact on fuel consumption by vehicles may be conditioned not only by its size and weight, but also by the geometry of the track motion, forces causing the motion and the forces acting on the car when driving on curved tracks. The vehicle encounters and overcomes all the forces that act on it while driving-resistance movement. In the energy intake through the vehicle runs in the motor changes at the expense of the energy of fuel consumed. The driving force performs work on a given stretch of road balancing (predominant) friction. On the basis of the calculated resistance movement and the energy consumption of the movement in the selected object was a comparison of the actual consumption of fuel in the vehicle with the ignition spark. Analysis was performed and found differences in three cycles: urban, extra-urban and combined.
Źródło:
Journal of KONES; 2014, 21, 4; 439-444
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Prediction of the mileage fuel consumption of passenger car in the urban driving cycle
Prognozowanie przebiegowego zużycia paliwa samochodu osobowego w cyklu miejskim
Autorzy:
Golebiewski, W.
Stoeck, T.
Powiązania:
https://bibliotekanauki.pl/articles/792391.pdf
Data publikacji:
2014
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
mileage fuel consumption
fuel consumption
passenger car
driving cycle
driving condition
operational parameter
linear velocity
rotational speed
engine
Źródło:
Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2014, 14, 3
1641-7739
Pojawia się w:
Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Linear positioning of railway objects
Autorzy:
Irlik, M.
Powiązania:
https://bibliotekanauki.pl/articles/196603.pdf
Data publikacji:
2017
Wydawca:
Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:
railway
ERTMS
ETCS
safety systems
signalling
measurement
line mileage
kolej żelazna
systemy bezpieczeństwa
sygnalizacja
pomiar
Opis:
The article provides an explanation of the issue related to the linear positioning of railway objects in the context of preparing site data for automatic train protection systems, such as the European Rail Traffic Management System/European Train Control System (ERTMS/ETCS). This paper identifies and compares current approaches for an object’s position based on a line chainage for orientation and documentation purposes, as well as the object’s position based on a track axis for the calculation of real world distances, along with providing examples of measurement systems and presenting conclusions from test runs for ERTMS/ETCS Level 2 purposes.
Źródło:
Zeszyty Naukowe. Transport / Politechnika Śląska; 2017, 96; 49-57
0209-3324
2450-1549
Pojawia się w:
Zeszyty Naukowe. Transport / Politechnika Śląska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Projections of the fuel consumption by the road transport in Poland
Autorzy:
Chłopek, Z
Waśkiewicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/245285.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
transport
motor transport
vehicle
annual mileage
fuel consumption
Opis:
The article presents expert estimates for 2010 and a forecast up to year 2030 regarding the number of passenger cars as well as trucks and special vehicles and buses according to the maximum weight group. In case of trucks and special vehicles, included were vehicles with maximum weight of less than 3.5 Mg and maximum weight of more than 3.5 Mg. As regards buses – the condition and forecast number of buses with maximum weight of less than 5.0 Mg and more than 5.0 Mg was presented. The forecast concerning passenger cars and other types of vehicles with maximum weight of less than 3.5 Mg (5.0 Mg in case of buses) focused on the number of vehicles by type of energy. The following types of energy were included: petrol, diesel oil, LPG, NG and electrical energy in case of passenger cars and light duty trucks. Estimates also included the average annual statistical mileage of a vehicle registered in Poland according to the specified category and type of energy. Based on the assumed assumptions in the 2030 perspective – the average fuel consumption was determined per 100 km of statistical mileage in every specified category. The predicted consumption of respective types of energy by the overall Polish car fleet was calculated and according to the specified category in years 2015, 2020, 2025 and 2030.
Źródło:
Journal of KONES; 2013, 20, 2; 33-39
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The analysis of conditions for testing mileage of military vehicles
Autorzy:
Luty, W.
Mieten, M.
Powiązania:
https://bibliotekanauki.pl/articles/30147053.pdf
Data publikacji:
2018
Wydawca:
Akademia Wojsk Lądowych imienia generała Tadeusza Kościuszki
Tematy:
mileage tests
special purpose vehicles
dynamic loads
Opis:
The study discusses the issue of determining the conditions for testing the mileage of a vehicle. Lifetime tests are the crucial element of qualification tests. This type of research verifies the resistance of vehicles and elements of their on-board equipment to vibrations and shocks resulting from the interaction of uneven surface during the movement. Certain test conditions can be straightforwardly determined and verified e.g. weather conditions or a type of the road/surface. The problem appears when the tests are to be conducted in field conditions (off-road). At the set driving speed, the level and frequency structure of dynamic loads of elements of a vehicle drive system depend mainly on a surface profile and its viscoelastic conditions. Either the profile or the characteristics of ground foundations change over the time depending on various factors. The paper attempts to assess the interaction of a ground surface of selected field roads on a vehicle. The result of direct measurement of the vertical acceleration captured on a drive axle and on a vehicle’s frame above the axle was addressed. The measurement results were analyzed within the context of possible planning of vehicle test requirements with the application of the method of testing mileage under the field conditions.
Źródło:
Scientific Journal of the Military University of Land Forces; 2018, 50, 3(189); 181-191
2544-7122
2545-0719
Pojawia się w:
Scientific Journal of the Military University of Land Forces
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies