Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "alloy" wg kryterium: Temat


Tytuł:
Microstructure and Fatigue Life of the Binary Lead-free Alloys with High Zn Content
Autorzy:
Pietrzak, K.
Klasik, A.
Maj, M.
Sobczak, N.
Powiązania:
https://bibliotekanauki.pl/articles/382479.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
lead free alloy
alloy microstructure
mechanical properties
stop bezołowiowy
mikrostruktura stopu
właściwości mechaniczne
Opis:
The results of studies presented in this article are an example of the research activity of the authors related to lead-free alloys. The studies covered binary SnZn90 and SnZn95 lead-free alloys, including their microstructure and complex mechanical characteristics. The microstructure was examined by both light microscopy (LM) and scanning electron microscopy (SEM). The identification of alloy chemical composition in micro-areas was performed by SEM/EDS method. As regards light microscopy, the assessment was of both qualitative and quantitative character. The determination of the geometrical parameters of microstructure was based on an original combinatorial method using phase quantum theory. Comprehensive characterization of mechanical behavior with a focus on fatigue life of alloys was performed by means of the original modified low cycle fatigue method (MLCF) adapted to the actually available test machine. The article discusses the fatigue life of binary SnZn90 and SnZn95 alloys in terms of their microstructure. Additionally, the benefits resulting from the use of the combinatorial method in microstructure examinations and MLCF test in the quick estimation of several mechanical parameters have been underlined.
Źródło:
Archives of Foundry Engineering; 2018, 18, 4; 65-70
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Researching the Influence of Chemical Composition and Technological Parameters on the Quality of Copper Alloys
Autorzy:
Rzadkosz, S.
Kozana, J.
Kranc, M.
Powiązania:
https://bibliotekanauki.pl/articles/379548.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
copper alloy
Cu-Zn alloy
mechanical properties
alloying additives
alloy refining
stop miedzi
stop Cu-Zn
właściwości mechaniczne
dodatki stopowe
rafinacja stopu
Opis:
The work presents the results of process efficiency of refining liquid copper with special refining agents and the analysis results of the influence of alloying components on the structure and properties of the chosen alloys. The research undertaken aimed at evaluation of the influence of alloying additives, such as aluminium, silicon and also cobalt in the chosen Cu-Zn alloys. The microstructures were researched with the help of light and scanning microscopy together with X-ray microanalysis to determine significant changes of mechanical properties.
Źródło:
Archives of Foundry Engineering; 2013, 13, 1 spec.; 153-158
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Degradation of Creep Resistant Ni - alloy During Aging at Elevated Temperature Part I: Mechanical Properties
Autorzy:
Kaczorowski, M.
Skoczylas, P.
Gulbinowicz, Z.
Powiązania:
https://bibliotekanauki.pl/articles/381428.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
creep resistant alloy
Ni alloy
mechanical properties
hydrogen embrittlement
stop żarowytrzymały
stop Ni
właściwości mechaniczne
kruchość wodorowa
Opis:
The results of experimental study of mechanical properties degradation of creep resistant Ni-base alloy are presented. The material studied was subjected to long-term influence of high pressure hydrogen atmosphere at temperature 750K and 850K. The mechanical properties of specimens taken at different distance from inner surface of thick wall tube were evaluated. The results of mechanical testing showed distinct influence of the temperature on mechanical properties of Ni creep resistant alloy. Moreover, the mechanical properties of studied alloy depend on the location of the specimen with respect to the dissociated ammonia source i.e. distance from the inner surface of the chamber. The results of mechanical testing show that the higher the distance from inner surface of the chamber the better mechanical properties of studied Ni base super-alloy.
Źródło:
Archives of Foundry Engineering; 2015, 15, 3 spec.; 25-28
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of thermo-derivative analysis conditions on microstructure of the Al-Si-Cu alloy
Autorzy:
Dobrzański, L. A.
Krupiński, M.
Labisz, K.
Rdzawski, Z.
Powiązania:
https://bibliotekanauki.pl/articles/380745.pdf
Data publikacji:
2011
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminium alloy
thermo derivative analysis
UMSA
alloy microstructure
mechanical properties
stop aluminium
analiza termopochodna
mikrostruktura stopu
właściwości mechaniczne
Opis:
Microstructure change of the metals and alloys as a result of variable crystallisation conditions also by mind of cooling rate change influence the mechanical properties. In this work there are presented the interdependences between the cooling rate, chemical composition and microstructure of the cast aluminium alloy Al–Si–Cu as a result of the thermo-derivative analysis, using the UMSA (Universal Metallurgical Simulator and Analyzer) device. An important tool for the microstructure evaluation of the Al type AC-AlSi7Cu3Mg alloy was the light and electron scanning microscopy technique.
Źródło:
Archives of Foundry Engineering; 2011, 11, 2 spec.; 19-22
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of casting defects on fatigue resistance of elektron 21 magnesium alloy
Autorzy:
Pikos, I.
Kiełbus, A.
Adamiec, J.
Powiązania:
https://bibliotekanauki.pl/articles/383305.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
casting defect
mechanical properties
microstructure
magnesium alloy
Elektron 21 alloy
wada odlewu
właściwości mechaniczne
mikrostruktura
stop magnezu
stop Elektron 21
Opis:
The Mg-RE alloys are attractive, constructional materials, especially for aircraft and automotive industry, thanks to combination of low density, good mechanical properties, also at elevated temperature, and good castability and machinability. Present paper contains results of fatigue resistance test carried out on Elektron 21 magnesium alloy, followed by microstructural and fractographical investigation of material after test. The as-cast material has been heat treated according to two different procedures. The fatigue resistance test has been conducted with 106 cycles of uniaxial, sine wave form stress between 9 MPa and 90 MPa. Fractures of specimens, which ruptured during the test, have been investigated with scanning electron microscope. The microstructure of specimens has been investigated with light microscopy. Detrimental effect of casting defects, as inclusions and porosity, on fatigue resistance has been proved. Also the influence of heat treatment's parameters has been described.
Źródło:
Archives of Foundry Engineering; 2013, 13, 2; 103-106
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Chemical Composition and Parameters of Heat Treatment on the Mechanical Properties and Electrical Conductivity in Hypoeutectic Aluminium Silicon Alloys
Badania nad wpływem składu chemicznego oraz parametrów obróbki cieplnej na własności mechaniczne i elektryczne stopów aluminium z grupy siluminów podeutektycznych
Autorzy:
Wiecheć, J.
Uliasz, P.
Knych, T.
Piwowarska-Uliasz, M.
Jarosz, R.
Powiązania:
https://bibliotekanauki.pl/articles/381346.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat treatment
aluminum alloy
hypoeutectic silicon alloy
mechanical properties
electrical properties
obróbka cieplna
stop aluminium
silumin podeutektyczny
właściwości mechaniczne
właściwości elektryczne
Opis:
The silumins are the aluminum alloys with the silicon as the main alloy addition. These are one of the most common types of casting alloys based on aluminum. They are widely used in technologies of casting such as sand casting, chill casting or pressure die casting. As their main characteristics we can include: very good castabillity, corrosion resistance, high mechanical properties and good thermal and electrical conductivity. Thanks to all these properties, the cast aluminum alloys have been used in various industries such as: automotive, engineering, heat exchangers or conductive elements. The last application requires a specific conditions of the process and the optimal chemical composition of the alloy, which allows to obtain high values of conductivity. The paper presents a study covering the impact of silicon content and heat treatment parameters on the electrical conductivity and mechanical properties (hardness HB) hypoeutetic silumin alloys such as AlSi11Mg, AlSi7Mg and AlSi5Mg. The aim of the study was to determine the optimal conditions for heat treatment parameters of various alloys providing to the most favorable mechanical and electrical properties.
Siluminy, czyli stopy aluminium z głównym dodatkiem w postaci krzemu, są jednymi z najczęściej stosowanych typów stopów odlewniczych na bazie aluminium. Są one wykorzystywane w szeregu technologiach odlewniczych takich jak: odlewanie piaskowe, kokilowe czy odlewanie nisko lub wysoko ciśnieniowe. Do podstawowych własności tej grupy stopów możemy zaliczyć bardzo dobrą lejność, odporność na działanie środowiska korozyjnego, wysokie własności mechaniczne oraz dobrą przewodność cieplną i elektryczną. Dzięki tym własnościom, główne zastosowanie odlewów z siluminów to przemysł samochodowy, maszynowy, elementy konstrukcyjne, wymienniki ciepła czy elementy przewodzące prąd elektryczny. Ta ostatnia aplikacja wymaga zapewnienia szczególnych warunków procesu technologicznego oraz odpowiedniego składu chemicznego stopu, tak aby uzyskać wysokie wartości przewodnictwa. W pracy przedstawiono badania obejmujące wpływ zawartości krzemu oraz parametrów obróbki cieplnej na przewodność elektryczną i własności mechaniczne (twardość HB) siluminów podeutektycznych typu AlSi11Mg, AlSi7Mg oraz AlSi5Mg. Celem badań było określenie optymalnych warunków obróbki cieplnej poszczególnych stopów umożliwiających uzyskanie najkorzystniejszych własności mechanicznych i elektrycznych.
Źródło:
Archives of Foundry Engineering; 2013, 13, 3 spec.; 179-184
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Structure and Mechanical Properties of AlSiCuMg Alloy after Thermo Processing
Autorzy:
Piątkowski, J.
Kamiński, P.
Powiązania:
https://bibliotekanauki.pl/articles/379577.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hypereutectic Al-Si alloy
overheating
CuP10 master alloy
mechanical properties
microstructure
stop nadeutektyczny Al-Si
przegrzanie
stop CuP10
właściwości mechaniczne
Opis:
In the dissertation it has been shown, that so called „time-thermal treatment” (TTT) of the alloy in liquid state, as overheating the metal with around 250°C above the Tliq. and detaining it in this temperature for around 30 minutes, improves the mechanical properties (HB, Rm, R0,2). It was ascertained, that overheating the AlSi17Cu5Mg alloy aids the modification, resulting with microcrystalline structure. Uniform arrangement of the Si primeval crystals in the warp, and α(Al) solution type, supersaturated with alloying elements present in the base content (Cu, Mg) assures not only increased durability in the ambient temperature, but also at elevated temperature (250°C), what is an advantage, especially due to the use in car industry.
Źródło:
Archives of Foundry Engineering; 2015, 15, 1; 79-82
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of structure and properties of welded joint of magnesium alloy EZ33A-T5
Autorzy:
Kocurek, R.
Adamiec, J.
Powiązania:
https://bibliotekanauki.pl/articles/380590.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
mechanical properties
weldability of alloy
magnesium alloy
EZ33
microstructure
quantitative procedure
właściwości mechaniczne
spawalność stopu
stop magnezu
mikrostruktura stopu
metoda ilościowa
Opis:
In recent years, improvement of casting magnesium alloys welding technology has resulted in an increase in the number of publications on this topic. The symptom of this trend is to replace traditional construction materials of magnesium alloys. Magnesium alloys of Mg-Zn-RE-Zr group are used in the automotive, aerospace and defense industries, mainly as gravitional casts to sand moulds or die-casting. Casting defects often appear in these casts (misruns, micro-shrinkage, cracks). The welding technologies are most often applicable to repair of casts, mainly nonconsumable electrode welding in the inert gas cover. The premise of this research work was to define structure and mechanical properties of welded joints of magnesium alloy EZ33A-T5. For this purpose, were attempted trails welding and conducted non-destructive testing, metallographic and strength mechanical tests allowing to assess the properties of welded joints. Evaluation of properties of welded joints was possible by carrying out welding trials and execution of non-destructive tests and metallographic. Research of the microstructure was used with the methodology and test procedures for the quantitative evaluation of the structure of welded joints which was developed in the Department of Materials Science of Silesian University of Technology.
Źródło:
Archives of Foundry Engineering; 2013, 13, 1 spec.; 65-71
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the Effect of the Cr, Mo, V and W Content in an Al-Si Alloy Used for Pressure Casting on its Proof Stress
Autorzy:
Szymczak, T.
Szymszal, J.
Gumienny, G.
Powiązania:
https://bibliotekanauki.pl/articles/380502.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
mechanical properties
statistical method
multicomponent alloy
Al-Si alloy
pressure casting
proof stress
właściwości mechaniczne
metoda statystyczna
stop wieloskładnikowy
stop Al-Si
odlewanie ciśnieniowe
Opis:
The study presents the results of the application of a statistical analysis for the evaluation of the effect of high-melting additions introduced into a pressure cast Al-Si alloy on the obtained level of its proof stress Rp0.2. The base Al-Si alloy used for the tests was a typical alloy used for pressure casting grade EN AC-46000. The base alloy was enriched with high-melting additions, such as: Cr, Mo, V and W. The additions were introduced into the base Al-Si alloy in all the possible combinations. The content of the particular high-melting addition in the Al-Si alloy was within the scope of 0.05 to 0.50%. The investigations were performed on both the base alloy and alloy with the high-melting element additions. Within the implementation of the studies, the values of Rp0.2 were determined for all the considered chemical compositions of the Al-Si alloy. A database was created for the statistical analysis, containing the independent variables (chemical composition data) and dependent variables (examined Rp0.2 values). The performed statistical analysis aimed at determining whether the examined high-melting additions had a significant effect on the level of Rp0.2 of the Al-Si alloy as well as optimizing their contents in order to obtain the highest values of the Al-Si alloy's proof stress Rp0.2. The analyses showed that each considered high-melting addition introduced into the Al-Si alloy in a proper amount can cause an increase of the proof stress Rp0.2 of the alloy, and the optimal content of each examined high-melting addition in respect of the highest obtained value of Rp0.2 equals 0.05%.
Źródło:
Archives of Foundry Engineering; 2018, 18, 2; 105-111
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research on Extruded Products of MgAlZn Alloys – Microstructure and Mechanical Properties
Badania wyrobów wyciskanych ze stopów MgAlZn – mikrostruktura i właściwości mechaniczne
Autorzy:
Płonka, B.
Remsak, K.
Korczak, P.
Lech-Grega, M.
Rajda, M.
Powiązania:
https://bibliotekanauki.pl/articles/352361.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnesium alloy
extrusion
mechanical properties
structure
stop magnezu
wyciskanie
właściwości mechaniczne
struktura
Opis:
The aim of the study was to test and assess products extruded from the magnesium alloys type MgAlZn: AZ31, AZ61 and AZ80A alloys in the form of Ø35mm round bars and 80x15mm flat bars. The test material was extruded in a direct system with the ram feed speed of 1 mm/s and the extrusion ratio λ = 7 ÷ 9. The extruded bars were examined in as-extruded state and after heat treatment to the T5 temper and T6 temper. The strength properties were tested and microstructure was examined with calculation of the average grain size.
Praca miała na celu zbadanie wyrobów uzyskanych w procesie wyciskania stopów magnezu typu MgAlZn: AZ 31, AZ 61 oraz AZ 80A w postaci prętów Ø35mm oraz płaskowników 80x15mm. Materiał do badań został wyciśnięty w systemie współbieżnym z prędkością posuwu tłoka 1 mm/s, przy współczynniku wydłużenia λ=7÷9. Wyciśnięte pręty analizowano w stanie wyciskanym oraz po obróbce cieplnej do stanu T5 i T6. Zbadano ich właściwości wytrzymałościowe jak również poddano analizie mikrostruktury z określeniem średniej wielkości ziarna.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 4; 2977-2980
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental study of Fe-Ni-Ti-Cr system
Autorzy:
Hoppe, Viktoria
Gibas, Anna
Grzegorczyk, Weronika
Małecki, Marcin
Hasiak, Mariusz
Powiązania:
https://bibliotekanauki.pl/articles/1188070.pdf
Data publikacji:
2019
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
właściwości mechaniczne
stopy z pamięcią kształtu
stop Fe-Ni-Ti
stop Fe-Ni-Ti-Cr
mechanical properties
shape memory alloys
Fe-Ni-Ti alloy
Fe-Ni-Ti-Cr alloy
Opis:
The research comprises a discussion about a formation of intermetallic phase with stoichiometric composition Fe2Ti, called Laves phase, and influence of chromium on the whole structure containing this phase by means of comparison of the two alloys. A base Fe35Ni35Ti30 alloy was used as a reference and then compared with a Fe-Ni-Ti chromium doped - Fe30Ni35Ti30Cr5 alloy. The study of microstructure performed with scanning electron microscope enabled to distinguish different phases. These regions are rich in mixture of Fe-Ni and Ti-Ni elements. The identified phases are Fe2Ti and Ni3Ti which was confirmed by X-ray diffraction and simultaneously it is consistent with energy dispersive spectroscopy results. Differential scanning calorimetry confirmed also multi-phase composition. As a result different hardness was measured for these phases using nanoindentation. The overall hardness was established using the Vickers method.
Źródło:
Interdisciplinary Journal of Engineering Sciences; 2019, 7, 1; 1--14
2300-5874
Pojawia się w:
Interdisciplinary Journal of Engineering Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Formation of Structure and Properties in Casting Processes on the Example of AZ91 Magnesium Alloy
Autorzy:
Augustyn, B.
Szymanek, M.
Kapinos, D.
Boczkal, S.
Korczak, P.
Powiązania:
https://bibliotekanauki.pl/articles/383152.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry technologies
innovative foundry materials
magnesium alloy
AZ91 alloy
RS process
mechanical properties
innowacyjne technologie odlewnicze
innowacyjne materiały odlewnicze
stop magnezu
stop AZ91
właściwości mechaniczne
Opis:
Contemporary materials engineering requires the use of materials characterised by high mechanical properties, as these precisely properties determine the choice of material for parts of machinery and equipment. Owing to these properties it is possible to reduce the weight and, consequently, the consumption of both material and energy. Trying to meet these expectations, the designers are increasingly looking for solutions in the application of magnesium alloys as materials offering a very beneficial strength-to-weight ratio. However, besides alloying elements, the properties are to a great extent shaped by the solidification conditions and related structure. The process of structure formation depends on the choice of casting method forced by the specific properties of casting or by the specific intended use of final product. The article presents a comparison of AZ91 magnesium alloys processed by different casting technologies. A short characteristic was offered for materials processed by the traditional semi-continuous casting process, which uses the solidification rates comprised in a range of 5 - 20⁰C/s, and for materials made in the process of Rapid Solidification, where the solidification rate can reach 106⁰C/s. As a result of the casting process, a feedstock in the form of billets and thin strips was obtained and was subjected next to the process of plastic forming. The article presents the results of structural analysis of the final product. The mechanical properties of the ø7 mm extruded rods were also evaluated and compared.
Źródło:
Archives of Foundry Engineering; 2014, 14, 2; 43-48
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The mechanical properties of AlSi17Cu5 cast alloy after overheating and modification of CuP master alloy
Autorzy:
Piątkowski, J.
Jabłońska, M.
Powiązania:
https://bibliotekanauki.pl/articles/380532.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hypereutectic Al-Si alloy
overheating
modification
CuP10 master alloy
mechanical properties
plastic properties
stop nadeutektyczny Al-Si
przegrzanie
modyfikacja
zaprawa CuP10
właściwości mechaniczne
właściwości plastyczne
Opis:
The paper presents the results of studies on the effect of the AlSi17Cu5 alloy overheating to a temperature of 920°C and modification with phosphorus (CuP10) on the resulting mechanical (HB, Rm, R0.2) and plastic (A5 and Z) properties. It has been shown that, so-called, "time-thermal treatment" (TTT) of an alloy in the liquid state, consisting in overheating the metal to about 250°C above Tliq., holding at this temperature by 30 minutes improves the mechanical properties. It has also been found that overheating of alloy above Tliq. enhances the process of modification, resulting in the formation of fine-grain structure. The primary silicon crystals uniformly distributed in the eutectic and characteristics of the \alfa(Al) solution supersaturated with alloying elements present in the starting alloy composition (Cu, Fe) provide not only an increase of strength at ambient temperature but also at elevated temperature (250°C).
Źródło:
Archives of Foundry Engineering; 2013, 13, 3; 68-71
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Assessment of Quality of EN AC-43300 Alloy with Use of ATND Method
Autorzy:
Pezda, J.
Powiązania:
https://bibliotekanauki.pl/articles/381845.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminum alloy
ATND method
mechanical properties
stop aluminium
metoda ATND
właściwości mechaniczne
Opis:
Application of the silumins expands together with nowadays tendency to reduction of design structures mass. Technological and mechanical properties of Al-Si casting alloys depend mainly from structure of eutectic mixture, which is modified in result of introduction of micro alloying elements to liquid alloy, and that is why proper use of knowledge on crystallization to control of crystallization kinetics of produced alloys to optimize obtained structure is a significant factor leading to improvement of quality of the castings. In the paper one depicts use of the ATND method (thermal-voltage-derivative analysis) and regression analysis to assessment of quality of the EN AC-43300 alloy modified with strontium on stage of its preparation, in aspect of obtained mechanical properties (R0,02, R0,2, Rm, A5). Obtained dependencies enable prediction of mechanical properties of the investigated alloy, basing on values of characteristic points from the ATND method.
Źródło:
Archives of Foundry Engineering; 2013, 13, 1 spec.; 139-142
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and physical properties of nanocrystalline Fe75B10Si10Cr5 alloy
Autorzy:
Baran, Dominika
Czyzewska, Natalia
Dziuba, Szymon
Przenajkowska, Julia
Piesiak, Mateusz
Hasiak, Mariusz
Powiązania:
https://bibliotekanauki.pl/articles/1189908.pdf
Data publikacji:
2019
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
metoda zasysania
stop nanokrystaliczny
właściwości mechaniczne
suction casting
nanocrystalline alloy
mechanical properties
Opis:
The main of this paper is to study the microstructure and physical properties of the Fe75B10Si10Cr5 in condition after being produced. The sample was prepared as cylindrical rod with a diameter of 3 mm. The rod was produced using the arc melting method with a suction casting option. It was found that produced alloy was nanocrystalline with average grains of about 15 nm. Due to the different cooling rates in the inner and outer part of the rod, variable sizes of dendrites in the material were observed. The presence of the dendrites was also confirmed on the surface by AFM investigations. The average roughness calculated for chosen profile of the examined area was 6 nm and average hardness of the material equals 844 HV. The mechanical properties were determined in respect to the Oliver-Pharr method. Young’s modulus of the Fe75B10Si10Cr5 calculated from load-displacement curve equals 128 GPa. Magnetic properties of the sample were measured by the vibrating sample magnetometer. The coercivity was equaled 2.184 kA/m, which is relatively low. It means that the Fe75B10Si10Cr5 alloy is magnetically soft.
Źródło:
Interdisciplinary Journal of Engineering Sciences; 2019, 7, 1; 17--22
2300-5874
Pojawia się w:
Interdisciplinary Journal of Engineering Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zastosowanie metody ATND do oceny właściwości mechanicznych okołoeutektycznego stopu AlSi12Cu2(Fe)
Application of the ATND method to assessment of mechanical properties of near eutectic AlSi12Cu2(Fe) alloy
Autorzy:
Pezda, J.
Powiązania:
https://bibliotekanauki.pl/articles/269764.pdf
Data publikacji:
2017
Wydawca:
Wrocławska Rada Federacji Stowarzyszeń Naukowo-Technicznych
Tematy:
aluminum alloy
mechanical properties
ATND
modification
crystallization
stop aluminium
właściwości mechaniczne
modyfikacja
krystalizacja
Opis:
Struktura i właściwości mechaniczne siluminów są w dużym stopniu zależne od szybkości chłodzenia, składu oraz operacji modyfikacji i obróbki cieplnej. W artykule opisano badania doświadczalne dotyczące zastosowania metody ATND (analiza termiczno-napięciowo- różnicowa) oraz analizy regresji do oceny jakości stopu AlSi12Cu2(Fe) modyfikowanego strontem na etapie jego przygotowania. Uzyskane zależności pomiędzy wartościami temperatury i napięcia w punktach charakterystycznych krzywych metody ATND umożliwiają predykcję właściwości mechanicznych (Rsp0,02, Rm, A5) badanego stopu. Pozwala to już na etapie przygotowania stopu ocenić jego właściwości mechaniczne bez konieczności prowadzenia pracochłonnych badań i wprowadzić ewentualne działania korygujące, mające na celu poprawę jego właściwości.
Structure and mechanical properties of silumins are highly dependent on cooling rate, composition and operations of modification and heat treatment. The present article describes experimental research concerning use of the ATND method (thermal-voltage-derivative analysis) and regression analysis to assessment of quality of AlSi12Cu2(Fe) alloy modified with strontium at the stage of its preparation. Obtained relationships between values of temperature and voltage in characteristic points on curves from ATND method enable prediction of mechanical properties (R0,02, Rm, A5) of the investigated alloy. This allows, as early as in preparation stage of the alloy, to evaluate its mechanical properties without need of labour consuming tests, and to introduce possible corrective measures aimed at improvement of its properties.
Źródło:
Inżynieria Maszyn; 2017, R. 22, z. 1; 47-57
1426-708X
Pojawia się w:
Inżynieria Maszyn
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analiza właściwości mechanicznych blachy wykonanej ze stopu tytanu Ti6Al4V w warunkach quasi-statycznych i dynamicznych obciążeń rozciągających
Mechanical properties analysis of the plate made of Ti6Al4V in the quasi-static and dynamic tensile loading
Autorzy:
Kostrzewski, C.
Moćko, W.
Powiązania:
https://bibliotekanauki.pl/articles/107333.pdf
Data publikacji:
2015
Wydawca:
Instytut Transportu Samochodowego
Tematy:
blacha
stop tytanu
proces rozciągania
właściwości mechaniczne
plate
titanium alloy
tensile process
mechanical properties
Opis:
W artykule przedstawiono metodykę badania próbek wykonanych ze stopu tytanu Ti6Al4V w warunkach quasi-statycznych oraz dynamicznych, przeprowadzonego odpowiednio z wykorzystaniem maszyny wytrzymałościowej oraz metody zmodyfikowanego pręta Hopkinsona. Przebieg procesu rozciągania zastał przeanalizowany metodą cyfrowej korelacji obrazu, w wyniku czego otrzymano rozkład wartości odkształcenia na powierzchni badanych próbek. Na podstawie danych zarejestrowanych przez maszynę wytrzymałościową oraz uzyskanych z użyciem teorii propagacji fal sprężystych w prętach wyznaczono krzywe rozciągania dla poszczególnych prób. W oparciu o uzyskane charakterystyki materiałowe stworzono model, który umożliwił symulację procesu rozciągania z wykorzystaniem metody elementów skończonych w środowisku ABAQUS/Standard.
This paper presents the testing methodology of specimens made of titanium alloy Ti6Al4V in the quasi-static and dynamic conditions. Tests was carried out using the testing machine and the split Hopkinson tensile bar method. The tensile process was analyzed by digital image correlation to give a strain distribution on the specimen surface. Based on data recorded from testing machine and data obtained using the theory of the elastic wave propagation in bars the tensile curves was created for each test. Furthermore the tensile test simulation was carried out using the gained material characteristics in the ABAQUS/Standard environment.
Źródło:
Transport Samochodowy; 2015, 3; 61-80
1731-2795
Pojawia się w:
Transport Samochodowy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Cyclic Sintering on the Structure and Mechanical Properties of Tungsten Heavy Alloy
Autorzy:
Skoczylas, P.
Kaczorowski, M.
Powiązania:
https://bibliotekanauki.pl/articles/379571.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
tungsten heavy alloy
multiple sintering
mechanical properties
stop ciężki wolframu
spiekanie wielokrotne
właściwości mechaniczne
Opis:
The results of structure and mechanical properties investigations of tungsten heavy alloy (THA) after cyclic sintering are presented. The material for study was prepared using liquid phase sintering of mixed and compacted powders in hydrogen atmosphere. The specimens in shape of rods were subjected to different number of sintering cycles according to the heating schemes given in the main part of the paper From the specimens the samples for mechanical testing and structure investigations were prepared. It follows from the results of the mechanical studies, that increasing of sintering cycles lead to decrease of tensile strength and elongation of THA with either small or no influence on yield strength. In opposite to that, the microstructure observations showed that the size of tungsten grain increases with number of sintering cycles. Moreover, scanning electron microscope (SEM) observations revealed distinctly more trans-granular cleavage mode of fracture in specimens subjected to large number of sintering cycles compared with that after one or two cycles only.
Źródło:
Archives of Foundry Engineering; 2016, 16, 4; 131-136
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Structure and properties investigation of MCMgAl12Zn1 magnesium alloy
Autorzy:
Dobrzański, L. A.
Król, M.
Powiązania:
https://bibliotekanauki.pl/articles/380517.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
thermal analysis
microstructure
mechanical properties
magnesium alloy
analiza termiczna
mikrostruktura
właściwości mechaniczne
stop magnezu
Opis:
This work presents an influence of cooling rate on crystallization process, structure and mechanical properties of MCMgAl12Zn1 cast magnesium alloy. The experiments were performed using the novel Universal Metallurgical Simulator and Analyzer Platform. The apparatus enabled recording the temperature during refrigerate magnesium alloy with three different cooling rates, i.e. 0.6, 1.2 and 2.4ºC/s and calculate a first derivative. Based on first derivative results, nucleation temperature, beginning of nucleation of eutectic and solidus temperature were described. It was fund that the formation temperatures of various thermal parameters, mechanical properties (hardness and ultimate compressive strength) and grain size are shifting with an increasing cooling rate.
Źródło:
Archives of Foundry Engineering; 2013, 13, 1; 9-14
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modyfikacja staliwa niskostopowego Cr-Mn-Si-Ni-Mo borem, tytanem i MZR
Grain Refinement of Low Alloy Cr-Mn-Si-Ni-Mo Cast Steel with Boron, Titanium and Rare Elements Additions
Autorzy:
Sobula, S.
Tęcza, G.
Krasa, O.
Wajda, W.
Powiązania:
https://bibliotekanauki.pl/articles/381555.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
modyfikacja staliwa
staliwo niskostopowe
właściwości mechaniczne
grain refinement
low-alloy cast steel
mechanical properties
Opis:
Staliwo niskostopowe jest materiałem o bardzo dobrych właściwościach mechanicznych, chętnie stosowanym na elementy maszyn pracujących w warunkach dużych obciążeń, a także w warunkach zużycia ściernego. Świetne właściwości wytrzymałościowe otrzymywane podczas produkcji odlewów z tego staliwa (Rm>1300 MPa), są uzyskiwane kosztem obniżenia plastyczności, która nie przekracza 10%. Dlatego celem badań była taka modyfikacja mikrostruktury, która pozwoliłaby otrzymać rozdrobnienie ziarna w stanie lanym, gwarantujące dobrą plastyczność po obróbce cieplnej odlewów. W artykule omówiono wyniki modyfikacji mikrostruktury staliwa L20HGSNM o zawartości 0,19÷0,23 %C; 0,75÷0,86 %Si; 0,93÷1,02 %Mn; 0,60÷0,65 %Cr; 1,02÷1,10 %Ni i 0,13÷0,16 %Mo. Modyfikację przeprowadzono przy pomocy żelazoboru, żelazotytanu i miszmetalu. Modyfikatory wprowadzano podczas spustu stali do kadzi. Stal odlewano do form piaskowych. Próbki do badań wycinano z wlewków typu Y przylanych do odlewów. Badano wpływ modyfikatorów na strukturę w stanie lanym, a także właściwości mechaniczne po ulepszaniu cieplnym. Uzyskano wydłużenie staliwa powyżej 12% przy wytrzymałości na rozciąganie przekraczającej 1000 MPa.
The low alloy cast steels have the good mechanical properties, and it finds wide area of applications in the manufacture of this parts, which work with high dynamic loads and in wear conditions. High strength obtained during manufacturing process results in a decrease of the elongation which hardly ever is over 10%. The aim of investigation was grain refinements which leads to small grain size in as-cast condition, resulting in a fine martensite, and an increase of the ductility. In this paper effects of grain refinement is observed in L20HGNM cast steel containing: 0,19÷0,23 %C; 0,75÷0,86 %Si; 0,93÷1,02 %Mn; 0,60÷0,65 %Cr; 1,02÷1,10 %Ni i 0,13÷0,16 %Mo. The grain refinement was treated by ferroboronium, ferrotitanium, and rare earth elements (REM). The refinement elements were introduced to the ladle during tapping. The steel was casted to the sand molds. Specimens were machined from keel-block coupons. The influence of modifying elements on the as-cast microstructure and mechanical properties after heat treatment were examined. It was obtained elongation over 12% and ultimate tensile strength over 1000 MPa.
Źródło:
Archives of Foundry Engineering; 2013, 13, 3 spec.; 153-156
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and mechanical properties of silicon-free Al-Cu-Ni casting alloys used in heavy duty aircraft engine parts
Mikrostruktura i właściwości mechaniczne odlewniczych bezkrzemowych stopów Al-Cu-Ni stosowanych na silnie obciążone elementy silników lotniczych
Autorzy:
Mrówka-Nowotnik, G.
Sieniawski, J.
Wierzbińska, M.
Nowotnik, A.
Powiązania:
https://bibliotekanauki.pl/articles/176064.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminium alloy
microstructure
heat treatment
mechanical properties
stop aluminium
mikrostruktura
obróbka cieplna
właściwości mechaniczne
Opis:
The main task of this work was to study the microstructure and mechanical properties of silicon-free Al-Cu-Ni casting alloys. The microstructure of tested samples was evaluated in terms of fracture mechanism using an optical microscope - Nikon 300, scanning electron microscope HITACHI S-3400 (SEM) in a conventional back-scattered electron mode and JEOL - JEM 2100 ARP TEM/STEM electron microscope. The mechanical (Rm and R0.2) and plastic (A,Z) properties of the examined alloy were evaluated by uniaxial tensile test at room temperature. The results shows that the casting method and the applied thermal processing did not have a significant influence on the primary (Al6Fe, Al2CuMg, Al7Cu4Ni, Al3(CuFeNi)2 and AlCuMn) intermetallic phase composition and microstructure phase component morphology. However, during prolonged heating growth and change in the shape of separations of the θ'-Al2Cu reinforcing phase occurs proportionally to temperature and heating time. Sand casts show higher mechanical properties: Rm R0.2. The stability of the mechanical properties of the investigated alloys in higher temperatures is the consequence of the increased Cu content.
Celem pracy była analiza mikrostruktury i właściwości mechanicznych odlewniczych, bezkrzemowych stopów Al-Cu-Ni. Obserwacje mikrostruktury prowadzono przy użyciu mikroskopu świetlnego -Nikon 300, elektronowego mikroskopu skaningowego HITACHI S-3400 z systemem EDS do mikroanalizy rentgenowskiej i elektronowego mikroskopu transmisyjnego JEOL - JEM 2100 ARP z systemem STEM/EDS. Właściwości wytrzymałościowe (Rm, R02) i plastyczne (A,Z) badanych stopów wyznaczono w próbie statycznej rozciągania w temperaturze pokojowej. Analiza uzyskanych wyników badań pozwoliła stwierdzić, że sposób odlewania oraz obróbka cieplna nie mają istotnego wpływu na skład fazowy oraz morfologię pierwotnych cząstek faz międzymetalicznych (Al6Fe, Al2CuMg, Al7Cu4Ni, Al3(CuFeNi)2 i AlCuMn. Długotrwałe wygrzewanie, w podwyższonej temperaturze powoduje jednak znaczny wzrost cząstek umacniającej fazy θ'-Al2Cu. Ustalono, że lepsze właściwości mechaniczne: Rm i R02 wykazują stopy odlane do form piaskowych. Stabilność właściwości mechanicznych badanych stopów w podwyższonej temperaturze jest spowodowana większą zawartością Cu.
Źródło:
Advances in Manufacturing Science and Technology; 2014, 38, 3; 77-93
0137-4478
Pojawia się w:
Advances in Manufacturing Science and Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ procesu KOBO na właściwości stopu CuCr1Zr
Influence of KOBO process on the properties of CuCr1Zr alloy
Autorzy:
Rozwalka, J.
Płaczek, G.
Andrzejewski, D.
Powiązania:
https://bibliotekanauki.pl/articles/211910.pdf
Data publikacji:
2017
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Obróbki Plastycznej
Tematy:
stop CuCrZr
wyciskanie KOBO
właściwości mechaniczne
alloy CuCr1Zr
KOBO extrusion
mechanical properties
Opis:
Autorzy pracy podjęli badania nad stopem CuCr1Zr w celu polepszenia jego właściwości mechanicznych oraz określenia ich stabilności w podwyższonej temperaturze. W badaniach wykorzystano niekonwencjonalną metodę obróbki plastycznej – wyciskanie metodą KOBO. Idea metody KOBO oparta jest na zewnętrznym wymuszeniu zlokalizowanego plastycznego płynięcia w pasmach ścinania poprzez nałożenie na jednokierunkowe, robocze oddziaływanie siłowe narzędzi kształtujących, dodatkowego, cyklicznie zmiennego oddziaływania w kierunku odmiennym od kierunku ruchu roboczego danego procesu. Wyciskaniu podano pręt w stanie T6 (bez powodzenia), a następnie pręt po przesycaniu z temperatury 900 i 1030°C (próba zakończona sukcesem). Wyciskanie metodą KOBO przeprowadzono dla prętów po przesycaniu, z dwoma wariantami chłodzenia (do powietrza i do wody). Podczas procesu wyciskania KOBO nastąpiła redukcja przekroju prętów z φ40 mm do φ ok. 12 mm, co dało stopień przerobu ok. 11,1, przy odkształceniu rzeczywistym ok. 2,4. Pręty, wyjściowy i wyciśnięte metodą KOBO, poddano badaniom twardości, statycznej próbie ściskania w temperaturze otoczenia oraz statycznej próbie rozciągania w temperaturze otoczenia i temperaturze podwyż- szonej do 450°C. Na podstawie uzyskanych wyników badań można stwierdzić, że zastosowanie metody odkształceń plastycznych (wyciskanie KOBO) pozwala umocnić materiał do tego stopnia, że wartości jego właściwości wytrzymałościowych przewyższają wartości uzyskane po obróbce cieplnej (stan T6). Natomiast w temperaturze 450°C dochodzi do spadku właściwości wytrzymałościowych o wartość od 25 do 40%.
The authors of this article conducted tests on CuCr1Zr alloy for the purpose of improving its mechanical properties and determining their stability at elevated temperatures. An unconventional plastic working method was utilized – KOBO extrusion. The idea of the KOBO method is based on external forcing of localized plastic flow in shear bands through the superposition onto the unidirectional operational force action of forming tools of an additional, cyclically variable action in a direction different from the direction of the given process’s operating direction. A rod in T6 state was extruded (unsuccessfully), followed by a extrusion of rod after hyperquenching from temperatures of 900 and 1030°C (test successful). KOBO extrusion was performed for hyperquenched rods with two cooling variants (in air and in water). During the KOBO extrusion process, the cross-section of rods was reduced from φ40 mm to approx. φ 12 mm, which yielded a reduction ratio of approx. 11.1 for an actual deformation of approx. 2.4. Rods, in original state and after KOBO extrusion, were subjected to hardness tests, static compression testing at room temperature and elevated temperature up to 450°C. Based on the obtained test results, it can be stated that the application of the method of plastic deformation (KOBO extrusion) makes it possible to harden the extent that the values of its strength properties exceed the values obtained after heat treatment (T6 state). However, at 450°C, strength properties decrease by 25 to 40%.
Źródło:
Obróbka Plastyczna Metali; 2017, 28, 2; 107-122
0867-2628
Pojawia się w:
Obróbka Plastyczna Metali
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect of Artificial Ageing on the Mechanical Properties of the EN AW 2017 Alloy
Autorzy:
Jirounkova, Klara
Vozka, Jan
Cais, Jaromir
Powiązania:
https://bibliotekanauki.pl/articles/102052.pdf
Data publikacji:
2020
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
aluminium alloy
heat treatment
aging
mechanical properties
stop aluminium
obróbka cieplna
starzenie
właściwości mechaniczne
Opis:
This paper deals with different types of artificial ageing and its effect upon the mechanical properties of an aluminium alloy. For the purposes of this research, the EN AW 2017 alloy was subjected to different types of heat treatment. These samples were subjected to different analyses. The results of hardness measurements (HB and HV) revealed the highest values of the non‑heat treated sample. The static tensile stress test proved the highest ductility of the heat treated samples. Overall, the best were revealed for the sample artificially aged at 160°C.
Źródło:
Advances in Science and Technology. Research Journal; 2020, 14, 1; 75-80
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Optimization of squeeze parameters and modification of AlSi7Mg alloy
Autorzy:
Zyska, A.
Konopka, Z.
Łągiewka, M.
Nadolski, M.
Powiązania:
https://bibliotekanauki.pl/articles/381007.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
mechanical properties
Al alloy
squeeze casting technology
modification
właściwości mechaniczne
stop Al
technologia prasowania
modyfikacja
Opis:
The paper present the examination results concerning mechanical properties of castings made of AlSi7MG alloy in correlation both with the most significant squeeze casting parameters and with the modification treatment. Experiments were planned and held according to the 23 factorial design. The regression equations describing the influence of the squeeze pressure, the mould temperature, and the quantity of strontium modifier on the strength and elongation of the examined alloy were obtained. It was found that the main factor controlling the strength increase is the squeeze pressure, while the plasticity (A5) of the alloy is affected most advantageously by modification. The application of modification treatment in squeeze casting technology enables for production of the slab-type castings made of AlSi7Mg alloy exhibiting strength at the level of 230 MPa and elongation exceeding 14%.
Źródło:
Archives of Foundry Engineering; 2013, 13, 2; 113-116
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High Temperature Mechanical Properties of AZ91 Magnesium Alloy Weld Joint
Autorzy:
Stopyra, M.
Adamiec, J.
Powiązania:
https://bibliotekanauki.pl/articles/382357.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
mechanical properties
AZ91 magnesium alloy
welding method
właściwości mechaniczne
stop magnezu AZ91
metoda spawania
Opis:
Magnesium alloys are widely applied in aircraft and automotive industry, due to their low density and high specific strength. Welding methods can be used to join Mg alloy elements and to repair or regenerate defective or worn-out castings. Therefore the influence of weld joint’s microstructure on mechanical properties needs to be studied. In present paper high temperature mechanical properties of AZ91 Mg alloy weld joint was investigated. Tensile tests were conducted in temperature range between 20 and 200°C. Ultimate tensile strength decreased as the temperature increased from 50°C. At temperature up to 150°C rapture occurred in the base metal, at 200°C rupture location switched to the weld fusion zone. Based on metallographic and fractographic observation, the fracture mechanism was described. Macro crack formed from the merger of micro cracks occurring at massive β phase precipitates.
Źródło:
Archives of Foundry Engineering; 2013, 13, 1 spec.; 181-184
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies