Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "cooling temperature" wg kryterium: Temat


Tytuł:
Zarządzanie temperaturą w bateriach samochodów elektrycznych – przegląd systemów chłodzenia
Temperature management in electric car batteries – review of cooling systems
Autorzy:
Skibińska, Agnieszka
Stępień, Zbigniew
Żółty, Magdalena
Powiązania:
https://bibliotekanauki.pl/articles/2143338.pdf
Data publikacji:
2022
Wydawca:
Instytut Nafty i Gazu - Państwowy Instytut Badawczy
Tematy:
zarządzanie temperaturą
samochody elektryczne
systemy chłodzenia
ciecze chłodzące
temperature management
electric cars
cooling systems
cooling liquids
Opis:
Polska jest jednym z największych rynków samochodów osobowych w Europie pod względem sprzedaży, zajmując szóste miejsce wśród krajów Unii Europejskiej i Europejskiego Stowarzyszenia Wolnego Handlu. Chociaż we flocie samochodów osobowych w Polsce dominują obecnie samochody z silnikami spalinowymi, kraj jest zaangażowany w zwiększanie liczby i udziału elektrycznych samochodów osobowych. Prawie 12 300 elektrycznych samochodów osobowych jeździło po polskich drogach do czerwca 2020 r. Ponad 56% z nich stanowiły pojazdy elektryczne na baterie (BEV). W niniejszym artykule zebrano informacje dotyczące stosowanych w samochodach elektrycznych systemów zarządzania temperaturą baterii. Przedstawiono sposoby chłodzenia z wykorzystaniem powietrza, czynnika chłodniczego, różnego rodzaju cieczy, materiałów o przemianie fazowej oraz systemu opartego na rurkach cieplnych, a także z zastosowaniem elementu termoelektrycznego. W czasie eksploatacji pojazdów BEV należy zwrócić szczególną uwagę na systemy zarządzania temperaturą baterii. Temperatura baterii wywiera różnorodny wpływ na działanie układu elektrochemicznego, co przekłada się na moc i efektywność energetyczną, bezpieczeństwo i niezawodność oraz koszt i okres użytkowania. W celu zapewnienia długiej żywotności i optymalnej wydajności baterii litowo-jonowych, należy zadbać o optymalny zakres temperatur oraz jednolity rozkład temperatury w pakiecie baterii i ogniwach.
Poland is one of the largest passenger car markets in Europe in terms of sales, ranking sixth place among the countries of the European Union and the European Free Trade Association. Although the passenger car fleet in Poland is currently dominated by cars with internal combustion engines, the country is committed to increasing the number and share of electric passenger cars. Almost 12 300 electric passenger cars were on Polish roads until June 2020. Over 56% of them were battery electric vehicles (BEV). This article gathers information on the temperature management systems used in electric cars. Cooling methods with the use of air, refrigerant, various types of liquids, materials with phase change and a system based on heat pipes as well as the use of a thermoelectric element were presented. When operating BEVs, particular attention should be paid to battery temperature management systems. Battery temperature has a variety of effects on the operation of the electrochemical system, which translates into power and energy efficiency, safety and reliability, cost and lifetime. In order to ensure the long life and optimal performance of lithium-ion batteries, care should be taken to ensure the optimal temperature range and uniform temperature distribution in the battery pack and cells.
Źródło:
Nafta-Gaz; 2022, 78, 3; 240-247
0867-8871
Pojawia się w:
Nafta-Gaz
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zarys bioklimatu Zamościa
The Bioclimate of Zamość
Autorzy:
Samborski, Andrzej
Powiązania:
https://bibliotekanauki.pl/articles/26850527.pdf
Data publikacji:
2023
Wydawca:
Akademia Zamojska
Tematy:
temperatura powietrza
wilgotność względna
prędkość wiatru
suma opadów atmosferycznych
wskaźnik wielkości ochładzającej
temperatura ekwiwalentna
temperatura efektywna
air temperature
relative humidity
wind speed
precipitation
cooling magnitude indicator
equivalent temperature
effective temperature
Opis:
W pracy wykorzystano dane ze stacji meteorologicznych funkcjonujących na terenie Zamościa w okresie od 1976 do 2020 roku. Opisano zmienność wartości wybranych elementów meteorologicznych i charakterystyk klimatycznych w skali czasowej, wykorzystując najczęściej stosowane statystyki rozkładu, tzn. wartości średnie oraz miary zmienności. Wyznaczono kierunek trendu zmian temperatury powietrza. W celu określenia warunków bioklimatycznych obliczono wartości wybranych wskaźników, takich jak: temperatura ekwiwalentna, temperatura efektywna i wielkość ochładzająca powietrza. Przeprowadzone badania wskazują, że w Zamościu optymalne warunki termiczne określane jako przyjemnie chłodno występują w okresie letnim (czerwiec, lipiec, sierpień), przy czym w lipcu są one łagodne. W kwietniu, maju i we wrześniu odczucie cieplne charakteryzowane jest jako chłodne. Generalnie w okresie od listopada do marca jest zimno, a w styczniu i w lutym bardzo zimno.
The paper uses data from meteorological stations operating in Zamość in the period from 1976 to 2020. The variability of the values of selected meteorological elements and climatic characteristics on a time scale was presented using the most commonly used distribution statistics, i.e. average values and variability measures. The direction of the trend of changes in air temperature was determined as well. In order to determine the bioclimatic conditions, the values of selected indicators were calculated, including equivalent temperature, effective temperature, and air cooling quantity. The conducted research indicates that in Zamość optimal thermal conditions described as pleasantly cool occur in the summer ( June, July, August), while in July they are mild. In April, May and September, the thermal sensation is characterized as cool. Generally, it is cold from November to March and very cold in January and February.
Źródło:
Facta Simonidis; 2023, 16, 1; 341-356
1899-3109
Pojawia się w:
Facta Simonidis
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Trendy temperatury powierzchni oceanu w sektorze pacyficznym Oceanu Południowego w ostatnim 25-leciu
Trends in the sea surface temperature in the Pacific sector of the Southern Ocean in the las 25 year period (1980-2004
Autorzy:
Marsz, A. A.
Powiązania:
https://bibliotekanauki.pl/articles/260641.pdf
Data publikacji:
2005
Wydawca:
Stowarzyszenie Klimatologów Polskich
Tematy:
temperatury powierzchni oceanu
ochłodzenie powierzchni oceanu
Ocean Południowy
sektor pacyficzny
Antarktyka
sea surface temperature
sea surface cooling
climatic changes
Southern Ocean
Pacific sector
Antarctic
Opis:
Praca omawia zmiany temperatury powierzchni wody (TPO) sektora pacyficznego Oceanu Południowego w pasach szerokości 60 i 50°S, zachodzące w przekrojach miesięcznych i rocznych. Stwierdzono występowanie ujemnych trendów TPO w całym pasie 60°S, z czego ponad 1/3 współczynników trendu jest istotna i wysoce istotna statystycznie. Obszary silnego ochłodzenia powierzchni oceanu tworzą tam dwa ośrodki: pierwszy w rejonie 170°E - 140°W, drugi - 120-080°W. W obu ośrodkach najsilniejsze spadki TPO następują w miesiącach chłodnej pory roku (maj - sierpień), w drugim - dodatkowo - stosunkowo silne ochłodzenie zaznacza się w miesiącach ciepłej pory roku (styczeń - marzec). Na szerokości 50°S ochłodzenie jest znacznie słabsze - istotne statystycznie zmiany TPO zaznaczają się wyłącznie po wschodniej stronie sektora (100-080°W), gdzie również występują trendy ujemne. Kumulacja istotnych i nieistotnych statystycznie trendów miesięcznych prowadzi do zaznaczania się na obszarze około 54% powierzchni sektora pacyficznego Oceanu Południowego istotnych statystycznie, ujemnych trendów rocznej TPO. Na pozostałym obszarze badanego sektora bądź brak realnych zmian TPO, bądź występuje tendencja do słabego spadku temperatury. Przebiegi temperatury rocznej wskazują, że w ośrodku zachodnim (60°S, 170°E -140°W) TPO konsekwentnie obniża się od początku obserwacji (1980 rok), gdy we wschodniej części sektora pacy-ficznego (120-080°W) cały obserwowany w 25-leciu trend stanowi konsekwencję silnego spadku rocznej TPO w ciągu ostatnich 7 lat (1997-2004).
This work deals with monthly and annual changes in sea surface temperature (SST) of the Pacific sector of the South Ocean observed in 60°- 50°S latitudinal bands. The occurrence of negative trends of SST was noted in the entire 60° band and 1/3 of the trend coefficients is statistically significant and highly significant. The regions marked by strong cooling of ocean surface are formed by two centres - one 170° - 140°W and the other extending from 120° to 080°W. The greatest decrease in sea surface temperature in both centres takes place during cold season (May - August), in the other centre there is also additional quite strong cooling in the months of warm season (January - March). In the latitude 50°S the cooling is much weaker - statistically significant changes in SST are observed only in the eastern part of the Pacific region (100°- 080°W) where negative trends are also noted. Cumulating of statistically significant and non-significant monthly trends leads to statistically significant negative trends in annual SST observed in 54% of the area in the Pacific sector of the South Ocean. In the remaining area of the Pacific sector of the South Ocean there are either no visible changes in the sea surface temperature or there is tendency of weak decrease in temperature. The courses of annual SST indicate that in the western region (60S°, 170° -140°W) the SST has been decreasing constantly since the beginning of the observational period (since the year 1980), whereas in the eastern part of the Pacific sector (120°- 080°W) the whole trend observed over the 25-year period results from strong decrease in annual SST in the period of last 7 years (1997-2004).
Źródło:
Problemy Klimatologii Polarnej; 2005, 15; 17-26
1234-0715
Pojawia się w:
Problemy Klimatologii Polarnej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of the Pouring Temperature on the Structure and Mechanical Properties of High-Chromium Cast Iron
Wpływ temperatury odlewania na strukturę i właściwości mechaniczne żeliwa wysokochromowego
Autorzy:
Kopyciński, D.
Siekaniec, D.
Powiązania:
https://bibliotekanauki.pl/articles/382417.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high chromium cast iron
pouring temperature
bending strength
cooling curves
microstructure
żeliwo wysokochromowe
temperatura odlewania
wytrzymałość
chłodzenie
Opis:
The article presents the results of the influence of pouring temperature on the structure and selected properties of high-chromium cast iron. The study was performed on two different pouring temperatures 1490°C and 1460°C for cast iron of the same chemical composition. Melts were performed in the induction furnace crucible capacity of 15 kg located in the Department of Engineering Alloys and Composites in Foundry Engineering Faculty of AGH. For each temperature cast 2 sets of rollers with dimensions ø30mm, ø20mm, ø15mm x 250mm. During the heats poured cup with installed S type thermocouple to record the cooling curves. Rollers put to the static bending strength test. Samples were cut from the rollers for the test microstructure. The study shown that the pouring temperature has a significant impact on the way of crystallization of high-chromium cast iron and consequently, on the microstructure and mechanical properties. It follows that, by appropriate selection of the pouring temperature can control certain properties of the casting.
W pracy przedstawiono wyniki badań wpływu temperatury odlewania na strukturę i wybrane właściwości wytrzymałościowe żeliwa wysokochromowego. W ramach badań wykonano dwa wytopy z różną wartością temperatury odlewania 1490 °C i 1460 °C, dla żeliwa o tym samym składzie chemicznym. Wytopy wykonano w piecu indukcyjnym o pojemności tygla 15 kg znajdującym się w Katedrze Inżynierii Stopów i Kompozytów Odlewanych na Wydziale Odlewnictwa AGH. Dla każdej temperatury odlano 2 zestawy wałków o wymiarach ø30 mm, ø20 mm, ø15 mm x 250 mm. Podczas wytopów zalano kubki pomiarowe z termoelementem typu S do rejestracji krzywej krystalizacji i stygnięcia. Wałki poddano statycznej próbie wytrzymałości na zginanie. Następnie z wałków wycięto próbki do badania mikrostruktury. Z przeprowadzonych badań wynika, że temperatura odlewania ma istotny wpływ na sposób krystalizacji odlewu z żeliwa wysokochromowego, a w konsekwencji na mikrostrukturę i właściwości wytrzymałościowe. Wynika z tego, że przez odpowiedni dobór temperatury odlewania można sterować niektórymi właściwościami mechanicznymi odlewu.
Źródło:
Archives of Foundry Engineering; 2014, 14, 4 spec.; 63-66
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of diesel engines thermal condition on fuel consumption and smoke of exhaust gases
Autorzy:
Pukalskas, S.
Pikunas, A.
Bureika, G.
Powiązania:
https://bibliotekanauki.pl/articles/245614.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engines fuel consumption
engine's thermal condition
temperature of engine's cooling liquid
smoke in exhaust
Opis:
The number of vehicles in the world is growing rapidly. Therefore, the global consumption of crude oil is increasing and its natural resources are being depleted. It causes the rise of oil fuel cost. Constantly rising energy prices and emironmental concerns have made energy saving the highest priority for transportation operators. The main goal of vehicles' operation is economy. The fuel consumption of the most popular internal combustion engines depends on various factors, and one of the most important of them is thermal condition. Energy or fuel saving is the main way to reduce operational expenses of vehicles. This paper aims to investigate fuel consumption of 1.9 liter volume direct injection diesel engine and to construct a diagram of the dependence of the amount of smoke in exhaust on the temperature of engine's operation. The temperature was fixed in the engine's crankcase, while the temperature of cooling liquid was measured at four points as well as during the engine's bench testing. Unexpected test results are obtained: when the temperature of exhaust gases rises above 70-75 °C, the amount of smoke increases by a few times. Finally, basic conclusions and recommendations are given.
Źródło:
Journal of KONES; 2009, 16, 3; 319-324
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The efficiency of waste hot water utilisation to improve the temperature conditions for growing plants
Autorzy:
Turcheniuk, Vasil
Rokochinskiy, Anatoliy
Kuzmych, Lyudmyla
Volk, Pavlo
Koptyuk, Roman
Romanyuk, Ivan
Voropay, Galyna
Powiązania:
https://bibliotekanauki.pl/articles/2174361.pdf
Data publikacji:
2022
Wydawca:
Instytut Technologiczno-Przyrodniczy
Tematy:
cooling
recycling
soil heating
soil temperature
waste water heat
water regime
Opis:
One of the rational ways of energy saving is to use the heat of wastewater from energy companies for open ground heating and cultivation crops. The most significant sources of heat are thermal and nuclear power plants that produce low-thermal waters of 28-35°C. Heating of the ground with the use of circulating warm water allows to increase temperature at all points of the soil profile. The maximum thermal effect from heating ground is observed at the depth of pipe heaters (7.3- 11.1°C). Ground heating allows to extend the growing season for crops by 3-4 weeks, which can expedite harvesting and thus maximise the harvest. In natural moisture conditions, ground heating does not lead to significant reduction of moisture reserves in the active layer throughout the growing period. There is a redistribution of moisture in a soil profile. It decreases in the zone of pipe heaters and redistributes toward the top. The formation of the nutrient regime changes, the content of mobile phosphorus and potassium, and nitrate nitrogen increases, whereas the content of ammonia nitrogen is reduced. Ground heating is a new special heat reclamation technique. It allows not only to control temperature of the agricultural crop environment, but also to dissipate heat in the ground, and promote the utilisation of waste heat and the stabilisation of the environment.
Źródło:
Journal of Water and Land Development; 2022, 54; 94--100
1429-7426
2083-4535
Pojawia się w:
Journal of Water and Land Development
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of storage time and temperature on the quality of natural yoghurt
Wpływ czasu przechowywania i temperatury na jakość jogurtu naturalnego
Autorzy:
Jakubowska, M.
Karamucki, T.
Powiązania:
https://bibliotekanauki.pl/articles/2615962.pdf
Data publikacji:
2019
Wydawca:
Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Tematy:
yoghourt
natural yoghourt
quality
storage time
storage temperature
cooling
physicochemical evaluation
microbiological analysis
organoleptic evaluation
Źródło:
Acta Scientiarum Polonorum. Zootechnica; 2019, 18, 4; 29-37
1644-0714
Pojawia się w:
Acta Scientiarum Polonorum. Zootechnica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect of Homogenization Conditions on the Structure and Properties of 6082 Alloy Billets
Wpływ warunków homogenizacji na strukturę i własności wlewków ze stopu 6082
Autorzy:
Woźnicki, A.
Leśniak, D.
Włoch, G.
Leszczyńska-Madej, B.
Wojtyna, A.
Powiązania:
https://bibliotekanauki.pl/articles/351632.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
6082 alloy
homogenization temperature
cooling rate after homogenization
stop 6082
temperatura homogenizacji
szybkość chłodzenia po homogenizacji
Opis:
The paper presents the results of laboratory homogenization investigations of the 6082 grade alloys, differing in Mg and Si content. At the first stage, the microstructure of alloys was analysed after homogenization finished with water quenching. SEM/EDS investigations and DSC tests were applied to evaluate the dissolution of the Mg2Si particles and concentration of the main alloying additions in the grains interiors, depending on soaking conditions. In the case of alloy with lower Mg and Si content, homogenization the temperature of 535ºC for 8h is sufficient for significant Mg2Si particles dissolution. For the alloy with higher Mg and Si content, after homogenization the temperature of 550ºC for 8h, the amount of undissolved Mg2Si particles decreases visibly, compared to homogenization at 535ºC for 8h. However, an unfavourable tendency of dispersoids growth is observed and these soaking conditions are not found to be recommended. At the second research stage, the influence of homogenization cooling rate on the size and distribution of the Mg2Si particles observed in the alloys microstructure was analysed. The ability of the Mg2Si particles, precipitated during various homogenization coolings, to rapid dissolution was estimated. For this purpose, the hardness after solution heat treatment with short annealing and ageing was determined and the DSC tests were performed. It was found, that cooling after homogenization at 315ºC/h is sufficient for precipitation of fine Mg2Si particles, which dissolve during subsequent rapid heating. Cooling at 40ºC/h, causes precipitation of Mg2Si phase in the form of large particles, unable for further fast dissolution.
W artykule przedstawiono wyniki laboratoryjnych badań homogenizacji dwóch stopów w gatunku 6082, różniących się zawartością Mg i Si. W pierwszym etapie analizowana była struktura stopów po homogenizacji z chłodzeniem w wodzie. Szczególną uwagę zwrócono na rozpuszczanie cząstek fazy Mg2Si podczas wygrzewania oraz zawartość głównych składników stopowych we wnętrzach ziarn. Oceny parametrów wygrzewania dokonano w oparciu o badania SEM/EDS oraz testy DSC. W przypadku stopu z niższą zawartością Mg i Si, homogenizacja w temperaturze 535ºC przez 8 h jest wystarczająca dla znaczącego rozpuszczenia cząstek fazy Mg2Si. W przypadku stopu z wyższą zawartością Mg i Si, po homogenizacji w temperaturze 550ºC przez 8h, udział nierozpuszczonych cząstek Mg2Si spada wyraźnie, w porównaniu z homogenizacją w temperaturze 535ºC przez 8h. Jednakże, stwierdzono niekorzystną tendencję do rozrostu dyspersoidów, zatem tych warunków wyżarzania nie uznano za rekomendowane. W drugim etapie analizowano wpływ szybkości chłodzenia z temperatury homogenizacji na wielkość i dystrybucję cząstek Mg2Si obserwowanych w strukturze stopów. Wykonano badania SEM oraz dokonano oceny możliwości szybkiego rozpuszczania cząstek Mg2Si wydzielonych podczas chłodzenia z temperatury homogenizacji z różnymi szybkościami. W tym celu wykonano badania twardości stopów po przesycaniu z krótkim wygrzewaniem oraz starzeniu, jak również badania DSC. Stwierdzono, że studzenie z temperatury homogenizacji z szybkością 315ºC/h jest wystarczające dla wydzielenia drobnych cząstek Mg2Si, które ulegają rozpuszczeniu podczas późniejszego gwałtownego nagrzewania. Chłodzenie z temperatury homogenizacji z szybkością 40ºC/h powoduje wydzielanie fazy Mg2Si w postaci dużych cząstek, które nie ulegają pełnemu rozpuszczeniu podczas późniejszego szybkiego nagrzewania.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 3A; 1764-71
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of cooling water temperature on the performance of a BWR nuclear power plant
Autorzy:
Laskowski, Rafał
Theimech, Mohamad
Uzunow, Nikołaj
Powiązania:
https://bibliotekanauki.pl/articles/2195750.pdf
Data publikacji:
2021
Wydawca:
Centrum Rzeczoznawstwa Budowlanego Sp. z o.o.
Tematy:
nuclear power plant
cooling system
cooling water temperature
boiling water reactor
BWR
elektrownia jądrowa
układ chłodzenia
temperatura wody chłodzącej
reaktor wrzący
Opis:
Although PWR reactors make up the large majority of the world's nuclear power plants, BWR reactors also have a share in this industry. It is difficult to find data on the performance of a BWR power plant in off-design and variable load conditions in the literature. Therefore, the paper presents how cooling water temperature affects the efficiency and power output of a BWR unit. The qualitative effect of changes and the trend related to the effect of cooling water temperature on the performance of the power plant are known, but the quantitative effect has to be determined for specific power units. Depending on the location of the nuclear power plant, various temperatures of cooling water for use in condensers and thus various operating conditions of the cooling system can be achieved. To analyze how cooling water temperature affects the performance of the power unit, a model of a BWR power plant was developed using the Ebsilon software. The model was based on data provided in [1] concerning LaSalle County Nuclear Generating Station. Calculations showed that within the examined range of cooling water temperatures at the condenser inlet between 10 and 28oC the gross power output of the unit decreases by 91.405 MW and the gross efficiency drops by 2.773 percentage points.
Źródło:
Modern Engineering; 2021, 3; 5--13
2450-5501
Pojawia się w:
Modern Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Testing of Air-Cooling Efficiency of the Underside of a Turning Tool Carbide Insert in EN-GJL 250 Cast Iron Turning Operations
Autorzy:
Bartoszuk, Marian
Prażmowski, Mariusz
Hurey, Igor
Powiązania:
https://bibliotekanauki.pl/articles/2201829.pdf
Data publikacji:
2022
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
cast-iron machining
air cooling systems
cutting temperature
surface roughness
tool wear
Opis:
This article shows the results of research on the effectiveness of operation of an original tool air cooling system in cutting. A case of turning EN-GJL 250 cast iron with TH10 tungsten carbide cutting inserts without protective coatings was selected for testing. The paper gives constructional details of the tested tool cooling system and discusses the principle of its operation. The research carried out has shown that this way of cooling the cutting insert causes a significant decrease in temperature in all sub-areas of the cutting zone. In addition, air cooling has been proven to significantly reduce cutting tool wear and slightly improve the roughness of the machined surface. The results obtained showed that the proposed method of cooling can be successfully used in the treatment of grey cast iron. In the future, it may serve as a basis for the construction of a professional cooling system for industrial applications.
Źródło:
Advances in Science and Technology. Research Journal; 2022, 16, 4; 1--9
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Symulacja zmian temperatury cieczy w chłodnicy samochodowej
Simulation of the temperature fluid changes in the cooler car
Autorzy:
Szada-Borzyszkowski, W.
Szada-Borzyszkowska, M.
Powiązania:
https://bibliotekanauki.pl/articles/316382.pdf
Data publikacji:
2016
Wydawca:
Instytut Naukowo-Wydawniczy "SPATIUM"
Tematy:
symulacja
chłodnica samochodowa
temperatura cieczy chłodzącej
simulation
car cooler
cooling liquid temperature
Opis:
W artykule przedstawiono analityczny i komputerowy model wymiany ciepła w chłodnicy samochodowej stanowiącej krzyżowo-prądowy lamelowy wymiennik ciepła. Zaprezentowano wyniki zmian temperatury cieczy chłodzącej w zależności od masowego natężenia przepływu cieczy oraz powietrza podczas procesu chłodzenia.
The article provides an analysis and computer model of heat exchange in the cooler car representing a cross-current lamella heat exchanger. The results of temperature changes of the cooling liquid depending on the mass flow rate of the liquid and air during the cooling process.
Źródło:
Autobusy : technika, eksploatacja, systemy transportowe; 2016, 17, 8; 142-145
1509-5878
2450-7725
Pojawia się w:
Autobusy : technika, eksploatacja, systemy transportowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on Effects of Mold Temperature on the Injection Molded Article
Autorzy:
Han, J.-H.
Kim, Y.-C.
Powiązania:
https://bibliotekanauki.pl/articles/351919.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
injection molding
mold temperature
cooling temperature
molded article
Opis:
This is a study of the effects of temperature of injection mold on the injection molded article. By supplying water of the proper temperature in the cooling line of mold in the cooling process, the mold was the appropriate temperature, and the deformation of the injection molded article was examined according to the mold temperature. In this study, we conducted simulation analysis and experiments, and the results were analyzed. The minimum deformation of the injection molded article model obtained by supplying 50°C water in the cooling line is 0.003 mm, and the maximum deformation was 0.813 mm. Injection molded article models obtained by supplying 20°C water were found to be a minimum of 0.002 mm, with deformation of up to 0.761 mm. When comparing both conditions, the error rate of injection molded article obtained by supplying 20°C water in the mold cooling line was lower by about 0.18%.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1271-1274
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Selection and calculation of air cooling solutions in underground coal mines in Vietnam
Dobór i obliczenia rozwiązań chłodzenia powietrza w podziemnych kopalniach węgla w Wietnamie
Autorzy:
Borowski, Marek
Trung Tien, Quan
Łuczak, Rafał
Życzkowski, Piotr
Powiązania:
https://bibliotekanauki.pl/articles/1841452.pdf
Data publikacji:
2020
Wydawca:
Polskie Towarzystwo Przeróbki Kopalin
Tematy:
air temperature
air humidity
air cooling
thermal power of cooler
temperatura powietrza
wilgotność powietrza
chłodzenie powietrza
moc cieplna chłodnicy
Opis:
Currently, Vietnamese underground mines have been exploited down to -500 m and, in the near future, they will be exploited deeper. The exploitation of coal of seams has an negative impact on a workers environment. The increase in the depth of coal seam exploitation causes is the increase of adverse microclimate factors such as temperature, moisture, heat radiation. According to the current Viet¬namese laws, coal deposits can be mined in a condition when air temperature does not exceed 30oC, although this rule is not always observed, especially during summer. The article show how reducing the adverse impact of climate factors in the mines and calculating the parameters which reduce the temperature on an example in one of underground coal mines in Vietnam.
Obecnie wietnamskie kopalnie podziemne zostały wyeksploatowane do -500 m, w najbliższej przyszłości będą eksploatowane głębiej. Eks¬ploatacja ma negatywny wpływ na środowisko. Działalność eksploatacji w wyrobiskach powoduje wzrost niekorzystnych czynników mi-kroklimatycznych, takich jak temperatura, wilgotność, promieniowanie cieplne. Zgodnie z obowiązującym wietnamskim prawem, złoża węgla mogą być eksploatowane w warunkach, gdy temperatura powietrza nie przekracza 30°C, chociaż nie zawsze jest to przestrzegane, zwłaszcza latem. W artykule przedstawiono rozwiązanie ograniczania niekorzystnego wpływu czynników klimatycznych w kopalniach oraz obliczenie parametrów obniżających temperaturę powietrza na przykładzie podziemnych kopalń węgla w Wietnamie.
Źródło:
Inżynieria Mineralna; 2020, 2, 2; 237-244
1640-4920
Pojawia się w:
Inżynieria Mineralna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Rola cyrkulacji atmosferycznej i zmian temperatury powierzchni morza w kształtowaniu zmienności temperatury powietrza na stacjach zachodniego wybrzeża Półwyspu Antarktycznego
Role of the atmospheric circulation and sea surface temperature changes in the formation of air temperature variability at the stations western coast of the Antarctic Peninsula
Autorzy:
Marsz, A. A.
Powiązania:
https://bibliotekanauki.pl/articles/260804.pdf
Data publikacji:
2013
Wydawca:
Stowarzyszenie Klimatologów Polskich
Tematy:
Półwysep Antarktyczny
roczna temperatura powietrza
ochłodzenie
temperatura powierzchni morza
wiatr geostroficzny
Antarctic Peninsula
annual air temperature
cooling
sea surface temperature
geostrophic wind
Opis:
Praca omawia przyczyny spadku temperatury powietrza obserwowanego po roku 2000 na stacjach północnego krańca Półwyspu Antarktycznego oraz osłabienia tempa wzrostu temperatury na stacjach środkowej i południowej części Półwyspu. Analiza przyczyn zachodzących zmian temperatury powietrza wskazuje, że czynnikiem odpowiedzialnym za spadki temperatury jest silny spadek temperatury powierzchni morza (dalej SST – sea surface temperature) na wodach Oceanu Południowego rozpościerających się na NW od Półwyspu Antarktycznego. Zarówno zmiany SST, jak i zmienność południkowych, ujemnych (z sektora północnego) składowych wiatru geostroficznego, które objaśniają łącznie około 60% wariancji rocznej temperatury powietrza na stacjach omawianego obszaru, zachodzą pod wpływem czynników naturalnych.
The paper presents the results of research into the role of changes in SST and atmospheric circulation variability in the formation of annual air temperature at the station the South Shetland Islands and the western coast of the Antarctic Peninsula. Four stations have been chosen for the analysis: Bellingshausen, Esperanza, Faraday / Vernadsky and Rothera. In this region (Fig. 2) these stations have the longest and most complete series of temperature measurements. After an analysis, annual average values of SST anomalies of the sea area extending from the N and NW of the area in question (variable SSTA20; see Fig. 2) and the average annual values of zonal and meridional components of geostrophic wind at the level of 1000 hPa (four points marked in Fig. 2) have been chosen as factors influencing the temperature variations at these stations. Regression analysis showed that SST variability and variability of meridional components of geostrophic wind of the points 60°S, 60°W and 65°S, 70°W have a strong, statistically significant influence on the variability of annual air temperature at the analyzed stations . Variability of zonal components of geostrophic wind does not play a significant role in shaping the temperature variation. The variability of meridional component of geostrophic wind and SST anomalies explain a total of about 60% of the observed variance of annual air temperature at the studied stations throughout the observation period (Table 2). The cause of the collapse of the strong positive trend of temperature after 2000, which occurred at these stations, is the occurrence of a sharp fall in SST in the analyzed sea area (Fig. 5). As a result, the South Shetland Islands and northern edge of the Antarctic Peninsula after 2000 began to cool, and the positive trend at stations in central and southern part of the Antarctic Peninsula became much weaker (Fig. 1). The analysis shows that the variation of meridional components of geostrophic wind and SST variability controlling temperature changes at the stations of west coast of the Antarctic Peninsula are a sign of natural processes. They are directly (SST anomalies) or indirectly (meridional components of geostrophic wind) the result of oceanic processes. This observed variability in temperature in the north of the region and the western coast of the Antarctic Peninsula, including a strong positive trend observed in the years 1951-2000 and its subsequent collapse in the years 2000-2012, must be regarded as a manifestation of natural variability.
Źródło:
Problemy Klimatologii Polarnej; 2013, 23; 21-42
1234-0715
Pojawia się w:
Problemy Klimatologii Polarnej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Regulacja temperatury w procesach fermentacji i dojrzewania piwa w tankofermentorze ®
Temperature control in processes fermentation and maturation of beer in fermentation tank®
Autorzy:
Kucharczyk, K.
Tuszyński, T.
Powiązania:
https://bibliotekanauki.pl/articles/228091.pdf
Data publikacji:
2017
Wydawca:
Wyższa Szkoła Menedżerska w Warszawie
Tematy:
tankofermentor
chłodzenie
proces fermentacji i dojrzewania piwa
fermentation tank
temperature control
cooling
fermentation and maturation process
Opis:
Do produkcji piwa używa się tankofermentory, tzw. tanki cylindryczno-koniczne (CKT) lub unitanki. To nowoczesne zbiorniki o różnorodnej wielkości, dostosowanej do zdolności wytwórczej browaru, które zapewniają ułatwiony przebieg procesu - wytwarzanie piwa w sterylnych warunkach. Uzyskiwanie optymalnych parametrów technologicznych wymaga zastosowania nowoczesnej techniki zwłaszcza w obszarze sterowania temperaturą. Jednym z ważnych elementów wyposażenia tenkofermentorów są instalacje chłodnicze, zapewniające właściwą temperaturę wewnątrz zbiornika. Do regulacji temperatury stosowane są zewnętrzne płaszcze chłodzące z automatycznym sterowaniem. Tankofermentory w zależności od sposobu zabudowy są odpowiednio izolowane w celu eliminacji wpływu czynników zewnętrznych na przebieg procesu technologicznego. Nowoczesna technika w połączeniu z zastosowaniem optymalnych parametrów przebiegu fermentacji i dojrzewania, stwarza możliwość wyprodukowania piwa wysokiej jakości. parametrów przebiegu fermentacji i dojrzewania, stwarza możliwość wyprodukowania piwa wysokiej jakości.
In the most of the breweries to produce beer used tankfermenters, conical-cylindrical tanks (CKT). It is a modern fermentation tank of various sizes, adapted to the capacity of the brewery to facilitate the manufacturing process and to ensure the production of beer in a sterile conditions. Obtaining optimal technological parameters requires the use of modern technology especially in the field of temperature control. One of the important pieces of equipment fermentation tank is refrigeration systems, ensuring the proper conduct of process temperature inside the tank. Adjusting the temperature of the fermenting wort, forced manufacturers to use high-technology cooling and automatic control of the process. For temperature control are used external cooling jackets. Fermentation tank depending on the type of installation is properly insulated in order to eliminate the influence of the external temperature on the course of the process. Modern technology in combination with the use of optimum technological parameters of the processes of fermentation and maturation makes it possible to produce high quality of beer.
Źródło:
Postępy Techniki Przetwórstwa Spożywczego; 2017, 1; 121-127
0867-793X
2719-3691
Pojawia się w:
Postępy Techniki Przetwórstwa Spożywczego
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies