Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "SnO2" wg kryterium: Temat


Wyświetlanie 1-15 z 15
Tytuł:
Structural, Morphological and Optical Characterization of SnO2:F thin films prepared by Chemical spray Pyrolysis
Autorzy:
Yousif, S. A.
Abass, J. M.
Powiązania:
https://bibliotekanauki.pl/articles/412231.pdf
Data publikacji:
2013
Wydawca:
Przedsiębiorstwo Wydawnictw Naukowych Darwin / Scientific Publishing House DARWIN
Tematy:
SnO2
SnO2:F
X-ray diffraction
optical characterization
Opis:
Fluorine doped tin oxide (FTO) films were successfully prepared on glass and quartz substrate at a substrate temperature equal to for different fluorine doping (0, 0.05, 0.1, 0.15) by a homemade spray pyrolysis technique. The spray solution prepared from tin tetrachloride pentahydrate dissolved in distilled water at concentration and ammonium fluoride was added into the solution for fluorine doping. X-ray diffraction patterns of the spray-deposited (SnO2: F) films for different fluorine doping show that all the diffractograms contain the characteristic SnO2 orientations. The matching of the observed and standard d-values confirm that the deposited films are of tin oxide with tetragonal structure and the films are polycrystalline with (110) as a preferred growth orientation. The surface morphology of thin film has been examined by atomic force microscopy (AFM). The average transmittance in the visible region (at 550 nm) has been found (40 %, 47 %, 52 %, 59 %, 61 %) for the fluorine doping (0, 0.05, 0.1, 0.15, 0.2) respectively.
Źródło:
International Letters of Chemistry, Physics and Astronomy; 2013, 13; 90-102
2299-3843
Pojawia się w:
International Letters of Chemistry, Physics and Astronomy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Electrochemical Properties of Flexible Anode with SnO2 Nanopowder for Sodium-Ion Batteries
Autorzy:
Kim, Huihun
Sadan, Milan K.
Kim, Changhyeon
Choi, Ga-In
Seong, Minjun
Cho, Kwon-Koo
Kim, Ki-Won
Ahn, Jou-Hyeon
Ahn, Hyo-Jun
Powiązania:
https://bibliotekanauki.pl/articles/2049149.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
word
sodium-ion batteries
SnO2 anode
flexible electrode
nano SnO2 particles
ether based electrolyte
Opis:
Sodium-ion batteries (SiBs) have attracted substantial interest as an alternative to lithium-ion batteries because of the low cost. There have been many studies on the development of new anode materials that could react with sodium by conversion mechanism. SnO2 is a promising candidate due to its low cost and high theoretical capacity. However, SnO2 has the same problem as other anodes during the conversion reaction, i.e., the volume of the anode repeatedly expands and contracts by cycling. Herein, anode is composed of carbon nanofiber embedded with SnO2 nanopowder. The resultant electrode showed improvement of cyclability. The optimized SnO2 electrode showed high capacity of 1275 mAh g-1 at a current density of 50 mA g-1. The high conductivity of the optimized electrode resulted in superior electrochemical performance.
Źródło:
Archives of Metallurgy and Materials; 2021, 66, 4; 931-934
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Warstwy proszkowe SnO2 nanoszone metodą eksplozji elektrycznej
Autorzy:
Kubicki, J.
Kwaśny, M.
Powiązania:
https://bibliotekanauki.pl/articles/192052.pdf
Data publikacji:
2008
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Technologii Materiałów Elektronicznych
Tematy:
warstwa proszkowa SnO2
metoda eksplozji elektrycznej
materiał proszkowy
Opis:
W artykule przedstawiono oryginalną metodę nanoszenia warstw z materiału proszkowego SnO2 na przygotowaną powierzchnię z wykorzystaniem impulsowego wyładowania elektrycznego wywołującego eksplozję, która powoduje jego rozpylenie, nadtopienie i wyrzucenie w kierunku podstawionej powierzchni. Pokazano schematy układu eksperymentalnego oraz wyniki badań naniesionych warstw SnO2 na płytki kwarcowe i ceramiczne. Zwrócono uwagę na możliwość wykorzystania otrzymanych warstw do wytwarzania elementów aktywnych sensorów chemicznych.
Original method of deposition of SnO2 powder materials onto prepared surface is presented in the paper. The method uses pulsed electrical discharge generating explosion which atomizes, partially melts, and ejects the material towards positioned surface. Experimental arrangement diagrams are presented as well as measurement results of SnO2 layers deposited onto quartz and ceramic plates are shown. An attention was paid to possibility of applying obtained layers as active elements for chemical sensors.
Źródło:
Materiały Elektroniczne; 2008, T. 36, nr 1, 1; 27-37
0209-0058
Pojawia się w:
Materiały Elektroniczne
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on the activity of ZnO-SnO2 nanocomposite against bacteria and fungi
Autorzy:
Omar, K.
Meena, B. I.
Muhammed, S. A.
Powiązania:
https://bibliotekanauki.pl/articles/109343.pdf
Data publikacji:
2016
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
ZnO-SnO2 nanocomposite
bacteria
fungi
sol-gel method
Opis:
ZnO-SnO2 nanocomposite was prepared by the sol-gel method. The as-prepared nanocomposite was characterized by X-ray diffraction (XRD), scanning electron micrograph (SEM-EDX), FTIR and UV-Visible spectrometer analysis techniques. The average particle size of nanocomposite was calculated from the XRD study. The average particle size of the prepared nanocomposite was 22 nm. According to the UV-Visible spectrum, the band gap value of 5.06 eV was obtained for the ZnO-SnO2nanocomposite. From the analysis techniques it was found that the metal oxides of ZnO-SnO2 mainly consist of ZnO and SnO2 metal oxides. The antibacterial and antifungal activities of the ZnO-SnO2nanocomposite were studied against Staphylococcus aureus (ATCC25923), Listeria monocytogenes (ATCC 11994)(Gram-positive), Salmonella typhi (ATCC14028), Escherichia coli (ATCC 25922)Gram-negative), Candida albicans (ATCC10231), and Aspergillus niger (ATCC 16404) (fungi)by two methods through the turbidity method or reading optical density and inhibition zone, which were carried out in the absence of irradiation. We observed an effective antibacterial and antifungal activity of the ZnO-SnO2 nanocomposite against bacteria and fungi.
Źródło:
Physicochemical Problems of Mineral Processing; 2016, 52, 2; 754-766
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characterization of SnO2/TiO2 with the Addition of Polyethylene Glycol via Sol-Gel Method for Self-Cleaning Application
Autorzy:
Halin, Dewi Suriyani Che
Azliza, Azani
Razak, Kamrosni Abdul
Abdullah, Mohd Mustafa Al Bakri
Salleh, Mohd Arif Anuar Mohd
Wahab, Juyana A
Chobpattana, Varistha
Kaczmarek, Łukasz
Nabiałek, Marcin
Jeż, Bartłomiej
Powiązania:
https://bibliotekanauki.pl/articles/2203743.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
TiO2
SnO2
thin film
polyethylene glycol
self-cleaning
Opis:
TiO2 is one of the most widely used metal oxide semiconductors in the field of photocatalysis for the self-cleaning purpose to withdraw pollutants. Polyethylene glycol (PEG) is recommended as a stabilizer and booster during preparation of water-soluble TiO2. Preparation of SnO2/TiO2 thin film deposition on the surface of ceramic tile was carried out by the sol-gel spin coating method by adding different amount of PEG (0g, 0.2g, 0.4g, 0.6g, 0.8g) during the preparation of the sol precursor. The effects of PEG content and the annealing temperature on the phase composition, crystallite size and the hydrophilic properties of SnO2/TiO2 films were studied. The X-ray diffraction (XRD) spectra revealed different phases existed when the films were annealed at different annealing temperatures of 350°C, 550°C and 750°C with 0.4 g of PEG addition. The crystallite sizes of the films were measured using Scherrer equation. It shows crystallite size was dependent on crystal structure existed in the films. The films with mixed phases of brookite and rutile shows the smallest crystallite size. In order to measure the hydrophilicity properties of films, the water contact angles for each film with different content of PEG were measured. It can be observed that the water contact angle decreased with the increasing of the content of PEG. It shows the superhydrophilicity properties for the films with the 0.8 g of PEG annealed at 750°C. This demonstrates that the annealed temperature and the addition of PEG affect the phase composition and the hydrophilicity properties of the films.
Źródło:
Archives of Metallurgy and Materials; 2023, 68, 1; 243--248
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impedance spectroscopy in H2 sensing with TiO2/SnO2 nanomaterials
Autorzy:
Szafraniak, Bartłomiej
Kusior, Anna
Radecka, Marta
Zakrzewska, Katarzyna
Powiązania:
https://bibliotekanauki.pl/articles/221225.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
impedance spectroscopy
TiO2
SnO2
hydrogen detection
resistive-type gas sensors
Opis:
Alternating current a.c. measurements enable to understand the physical and chemical processes occurring in semiconductor materials. Impedance spectroscopy has been successfully applied to study the responses of gas sensors based on metal oxides, such as TiO2, SnO2 and TiO2/SnO2 nanocomposites. This work is devoted to dynamic measurements of hydrogen sensor behaviour over the temperature range of 300-450°C. Frequency dependence of the impedance signal gives evidence that 50 mol% TiO2/50 mol% SnO2 nanocomposites should be treated as resistive-type sensors. Temporal evolution of the response to 500 ppm H2 at 320°C indicates a very short response time and much longer recovery.
Źródło:
Metrology and Measurement Systems; 2020, 27, 3; 417-425
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Enhanced photoelectrical performance of DSSC by Co-doped SnO2 nanoparticles
Autorzy:
Priyadharsini, C. I.
Prakasam, A.
Anbarasan, P. M.
Powiązania:
https://bibliotekanauki.pl/articles/412628.pdf
Data publikacji:
2013
Wydawca:
Przedsiębiorstwo Wydawnictw Naukowych Darwin / Scientific Publishing House DARWIN
Tematy:
co–doped SnO2 nanoparticles
Natural Sensitizer
Structural properties
Absorption spectrum
Opis:
Investigation of the I-V characteristics of the DSSC based on interconnected with cobalt-doped SnO2 nanoparticles covered with a nano-scale thin layer which was absorbed by natural dyes are described. The presence of co-doped SnO2 has been confirmed by its characteristic XRD pattern and the shape of the particle is confirmed by SEM. The thickness of the protective layer can be conveniently controlled by the mole value of co-doped SnO2 used in the preparation of the thin film and the optimum conditions for best performance of the DSSC are presented together with possible explanation for the variations observed. An optimum light-to-electricity conversion efficiency of 0.37 % in the presence of a layer of co-doped SnO2 has been obtained which enhancement over the cell prepared with other natural dyes. The characterization of the sample using different techniques was explained (change the sentence).
Źródło:
International Letters of Chemistry, Physics and Astronomy; 2013, 12; 82-93
2299-3843
Pojawia się w:
International Letters of Chemistry, Physics and Astronomy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Improved Photovoltaic Properties Of Dye-Sensitized Solar Cells Using Laser Patterned F-Doped SnO2 Thin Films
Poprawa właściwości fotowoltaicznych ogniw słonecznych uczulonych barwnikiem przez laserową modyfikację powierzchni cienkich warstw SnO2
Autorzy:
An, H.-R.
An, H.
Riu, D.-H.
Ahn, H. J.
Powiązania:
https://bibliotekanauki.pl/articles/353636.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
dye-sensitized solar cells
F-doped SnO2 thin films
surface morphology
laser patterning
fotowoltaniczne ogniwa słoneczne
cienkie warstwy SnO2
morfologia powierzchni
modyfikacja laserowa
Opis:
We modified the surfaces of F-doped SnO2 thin films using laser patterning to improve the photovoltaic properties of dye-sensitized solar cells. To do so, we varied the laser power density and the distance between laser-patterned lines. First, we investigated three power densities. Higher densities led to higher sheet resistances owing to increases in surface roughnesses. The lowest power density increased surface roughness without electrical degradation. Next, we explored three line spacings at a fixed power density. The films with the narrowest spacing exhibited the highest power conversion efficiency (~7.00%), the highest short-circuit photocurrent density (16.28 mA/cm2), and a good fill factor (58.82%).
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1241-1245
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Studies on spray pyrolised nanostructured SnO2 thin films for H2 gas sensing application
Autorzy:
Bari, R. H.
Patil, S. B.
Powiązania:
https://bibliotekanauki.pl/articles/411918.pdf
Data publikacji:
2014
Wydawca:
Przedsiębiorstwo Wydawnictw Naukowych Darwin / Scientific Publishing House DARWIN
Tematy:
Spray Pyrolysis
Nanostructured SnO2
thin films
H2 gas sensor
Microstrain
Electrical conductivity
Opis:
The objective of this work is to study the influence of pyrolysis temperature on structural, surface morphology and gas sensing properties of the nanostructured SnO2 thin films prepared by spray pyrolysis technique. These films were characterized for the structural, morphological and elemental composition carried by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectrophotometer (EDAX). The information of crystallite size, dislocation density and microstrain is obtained from the full width-at half- maximum (FWHM) of the diffraction peaks. Effect of sprayed deposition temperature on H2 gas sensing performance and electrical properties were studied using static gas sensing system. The sensor (Tpyr. = 350 °C) showed high gas response (S = 1200 at 350 °C) on exposure of 500 ppm of H2 and high selectivity against other gases The results are discussed and interpreted.
Źródło:
International Letters of Chemistry, Physics and Astronomy; 2014, 17, 2; 125-141
2299-3843
Pojawia się w:
International Letters of Chemistry, Physics and Astronomy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Nowy rodzaj bezchromowych, zasadowych wyrobów ogniotrwałych
New types of chrome free basic refractories
Autorzy:
Wojsa, J.
Jedynak, L.
Podwórny, J.
Wala, T.
Powiązania:
https://bibliotekanauki.pl/articles/392428.pdf
Data publikacji:
2008
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Ceramiki i Materiałów Budowlanych
Tematy:
metalurgia miedzi
materiał ogniotrwały
zastąpienie chromu
tworzywo spinelowe
kompozycja MgO-AI2O3-SnO2
copper metallurgy
refractory material
chromium replacement
spinel material
MgO-AI2O3-SnO2 composition
Opis:
Ze względu na szkodliwe działanie na organizm ludzki związków chromu na +6 stopniu utlenienia, od lat prowadzone są badania mające wyeliminować tlenek chromu z technologii zasadowych materiałów ogniotrwałych. Poszukiwanie tworzyw alternatywnych umożliwiło opracowanie materiałów o zbliżonych własnościach i w perspektywie ograniczenie zakresu stosowania wyrobów zawierających chrom. Niemniej w wielu gałęziach przemysłu, a zwłaszcza w metalurgii miedzi i ołowiu, a także w niektórych procesach pozapiecowej obróbki stali, nadal stosowane są niemal wyłącznie tworzywa magnezjowo-chromitowe zawierające do ponad 30% Cr2O3. Celem podjętych badań było opracowanie nowych tworzyw ceramicznych mogących stanowić alternatywę materiałową dla klasycznych wyrobów magnezjowo-chromitowych tam, gdzie odgrywają one role dominującą, a więc w przemyśle miedziowym. W badaniach nad nowego typu tworzywami ogniotrwałymi jako składnik spinelotwórczy zastosowano kasyteryt (SnO2). Wyniki badań zależności fazowych tworzyw z układu MgO-AI2O3-SnO2 oraz podstawowych własności otrzymanych wyrobów próbnych łącznie z rezultatami laboratoryjnych testów odporności korozyjnej prezentowano we wcześniejszych publikacjach. W niniejszej pracy zaprezentowano wybrane wyniki dalszych badań własności nowych tworzyw spinelowo- i magnezjowo-cynianowych. Przedstawione rezultaty potwierdzają prawidłowość wyboru kierunku poszukiwań alternatywnych wyrobów bezchromowych, zwłaszcza do zastosowania w procesach niskotemperaturowych w metalurgii miedzi.
In the last decade one of the most important objectives of many researching attempts in basic refractories was the elimination of chrome oxide due to environmental and human health protection reasons. However, there are still areas where replacement of magnesite-chrome bricks is unattainable. Accordingly attempts were undertaken to develop new materials in which the spinel creating agent was cassiterite (SnO2). Results of investigations into phase compositions of materials from MgO-AI2O3-SnO2 system and analysis of fundamental factors having an effect on its practical application as well as the results of corrosion resistance tests were presented earlier. In this paper further properties of the new, spinel- and magnesia-stannate materials were examined. The results, which have been obtained so far seem to be promising, especially those concerning the application of new refractories in low temperature processes in copper industry.
Źródło:
Prace Instytutu Szkła, Ceramiki, Materiałów Ogniotrwałych i Budowlanych; 2008, R. 1, nr 2, 2; 67-75
1899-3230
Pojawia się w:
Prace Instytutu Szkła, Ceramiki, Materiałów Ogniotrwałych i Budowlanych
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis And Characterization Of SiO2, SnO2 And TiO2 Metal Oxide Shells Covering Cu2O Particles
Synteza i charakterystyka powłok tlenkowych SiO2, SnO2 i TiO2 pokrywających cząstki Cu2O
Autorzy:
Yu, R.
Yun, J.
Kim, Y.
Powiązania:
https://bibliotekanauki.pl/articles/355566.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Cu2O
metal oxide coating
pH value
SiO2
TiO2
SnO2
powłoki tlenkowe
Opis:
In this work is described a means of improving the chemical stability of Cu2O@SiO2, Cu2O@SnO2 and Cu2O@TiO2 materials. The SiO2, SnO2 and TiO2 coated samples were stable from pH 3 to pH 10 for up to seven days. To determine the stability of the coated nanoparticles, and their colloidal solutions under acidic and basic conditions, colloidal nanoparticle solutions with various pH values were prepared and monitored over time. Details of the effect of variations in pH on the phase stability of core-shell type Cu2O were characterized using transmission electron microscopy and X-ray diffraction.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1159-1163
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of fluorine and tungsten co-doping on optical, electrical and structural properties of tin (IV) oxide thin films prepared by sol–gel spin coating method
Autorzy:
Keskenler, E F
Turgut, G
Aydin, S.
Dogan, S
Duzgun, B
Powiązania:
https://bibliotekanauki.pl/articles/175016.pdf
Data publikacji:
2013
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
tin (IV) oxide (SnO2)
fluorine (F) and tungsten (W) co-doping
sol-gel
Opis:
Fluorine and tungsten co-doped tin (IV) oxide (WFTO) thin films have been prepared first time by a sol–gel spin coating method. The effect of F and W co-dopant ratio on optical, electrical and structural properties of SnO2 was investigated. It was found that the optical properties of the films were obviously affected by the co-dopant ratio. When the F:W co-dopant ratio increases from 0.25:0.25 to 0.75:0.50, the transmittance in the short wavelengths slightly increases and transmittance edge shifts towards shorter wavelength. With an increase in the co-dopant ratio, the reduction and red shifts in the optical transmittance edge are very obvious at all wavelengths. Transmittance values at 550 nm for the films have varied between 79.64% and 50.20%. The indirect and direct band gap values for WFTO-1, WFTO-2, WFTO-3 and WFTO-4 samples were calculated to be 3.73, 3.79, 3.48, 3.40 eV and 4.03, 4.04, 3.98, 3.97 eV, respectively. The crystal structure of the films has been investigated by X-ray diffraction patterns. It has been observed that WFTO-1 and WFTO-2 samples have (111) preferential orientation corresponding to SnO2 cubic phase. This orientation almost disappears and changes to tetragonal phase (110) orientation for WFTO-3 and WFTO-4. To the best of our knowledge, this is the first cubic structure observation for SnO2 grown by the sol–gel technique. The electrical properties were also changed with co-doping ratio. The best optical, electrical and structural properties were obtained for mole ratio 0.75:0.50 (F:W).
Źródło:
Optica Applicata; 2013, 43, 4; 663-677
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wykorzystanie mikroskopii AFM do wizualizacji efektów prac nad otrzymaniem tlenków cyny SNO2
The SNO2 formation proces observation and visualisation using AFM
Autorzy:
Lubańska, Z.
Grudniewski, T.
Chodyka, M.
Powiązania:
https://bibliotekanauki.pl/articles/252767.pdf
Data publikacji:
2015
Wydawca:
Instytut Naukowo-Wydawniczy TTS
Tematy:
mikroskopia (AFM)
SnO2
mikroskopia skaningowa
mikroskopia atomowa
STM
AFM
AFM microscopy
scanning microscopy
atomic microscopy
Opis:
W artykule przedstawiono charakterystyki cienkich warstw SnO2 na czystym szkle. Warstwy SnO2 nanoszone były metodą magnetronowego sputteringu (nanoszenie) na podłoże szklane w różnych temperaturach. Wykorzystano do tego urządzenie Magnetron Line 440. Do badania składu i morfologii warstwy użyto mikroskopii skaningowej i atomowej (STM/AFM). Na podstawie badań stwierdzono, że powłoki wykazują dobre połączenie z materiałem podłoża, charakteryzują się zróżnicowaną chropowatością i są jednorodnie chemiczne.
Atomic force microscopy is one of the most popular method used in surface imaging. This method allows to measure the surface topography and determine the dimensions of the structures in the subatomic resolution [1]. Due to its properties, it can be applied to the measurement of conductors and semiconductor surfaces prepared in various processes. The experiment is fo-cused on SnO2 and ITO thin layers which can be used as transparent electrodes [2]. The authors are trying to illustrate the correlation between process parameters - creation of semiconductor in magnetron sputtering by different process conditions (temperature and cooling process, gas pressure and composition), surface of the sample and its other electrooptical parameters.
Źródło:
TTS Technika Transportu Szynowego; 2015, 12; 944-946, CD
1232-3829
2543-5728
Pojawia się w:
TTS Technika Transportu Szynowego
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Al-Sn nanostructured coatings on aluminum surfaces using electrospark alloying and their wear behawior
Autorzy:
Yurchenko, E. V.
Rushika, I. D.
Agafii, V. I.
Dikusar, A. I.
Powiązania:
https://bibliotekanauki.pl/articles/95183.pdf
Data publikacji:
2018
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
Al-Sn alloy
electrospark alloying
nanostructuring
SnO2 nanofibers
wear resistance
stop Al-Sn
stopowanie elektroiskrowe
nanostruktura
nanowłókna
odporność na zużycie
Opis:
At electrspark alloying (ESA) of aluminum surfaces using Al-Sn tool-electrode (TE), nanostructuring of manufactured surfaces take place owing to the formation of SnO2 nanofibers. Examining the tribological properties of these surfaces in a friction couple with a counterbody made of hardened steel showed that the wear of counterbody during the friction in the oil and at dry friction exceeds by an order of magnitude and above it the wear of such surfaces.
Źródło:
Journal of Mechanical and Energy Engineering; 2018, 2, 2; 115-120
2544-0780
2544-1671
Pojawia się w:
Journal of Mechanical and Energy Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Red photonic glasses and confined structures
Autorzy:
Gonçalves, R. R.
Lukowiak, A.
Ristic, D.
Boulard, B.
Chiappini, A.
Chiasera, A.
Dorosz, D.
Marciniak, M.
Righini, G. C.
Ferrari, M.
Powiązania:
https://bibliotekanauki.pl/articles/953055.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
glass photonics
rare earth ions
waveguides
integrated optics
glass-ceramic
microspheres
whispering gallery modes
SiO2-HfO2
SiO2-SnO2
fotonika szkła
jony pierwiastków ziem rzadkich
falowody
optyka zintegrowana
ceramika szklana
mikrokulki
SiO2- HfO2
Opis:
We present some recent results obtained by our team in rare earth doped photonic glasses and confined structures, in order to give some highlights regarding the state of art in glass photonics. To evidence the unique properties of transparent glass ceramics we compare spectroscopic and structural properties between the parent glass and the glass ceramics. Starting from planar waveguides we move to spherical microresonators, a very interesting class of photonic confined structures. We also conclude the short review with some remarks about the perspective for glass photonics.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2014, 62, 4; 647-653
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-15 z 15

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies