Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Diesel engine" wg kryterium: Temat


Tytuł:
Analysis of application of chosen methods for tdc determination in marine diesel engines
Autorzy:
Łutowicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/245396.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
transport
marine diesel engine
indication
TDC
Opis:
In the operating marine diesel engines the indication diagnostics tests are usually performed through a 0.5-1.0 me ter long indication channel which delays and disfigures the pressure signal being measured. the delay depends on the engine 's speed and load. the pressure sensor itself together with an amplifler is an additional source of delay and disfigurements, so the registered pressure curve is displaced even if theTDC piston's position hadbeen estimated with the highest accuracy. when the over exploited engine is being tested the angle of delay can achieve several degrees and differ for each cylinder. in that case cylinders' load is unequal and torsional vibrations occur in the engine operation. in case when some simplifying assumptions have been adopted the part of diagnostic information is lost what could lead to a false diagnosis. in the paper the attention is focused on the mistakes which could be made in the marine diesel engine diagnostics when different TDC assessment methods are used. TDC corrections with compression pressure analysis are possible only in case when crankshaft angle position is precise. in case of measurement with constant frequency such corrections are possible only when the engine is good balanced.
Źródło:
Journal of KONES; 2009, 16, 4; 301-306
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impact analysis of internal catalyst converter on operating parameters of VW 1.9 TDI engine
Autorzy:
Haller, P.
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/242517.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
catalyst
diesel engine
emissions
Opis:
The largest amount of air pollutants is produced by the combustion of fossil fuels (coal, lignite, petroleum, natural gas, etc.). Such combustion releases huge amounts of greenhouse gases into the atmosphere (including carbon oxides (CO, CO2), sulphur oxides (SO2, SO3), nitrogen oxides (NO, NOx)) and dust, ashes and soot. Transportation is a significant share of the air pollution, mainly wheel-based transportation. The combustion process in diesel engine is very complex physico-chemically and varies in time. The process is accompanied by simultaneous exchange of heat and mass and chemical reactions. The development of internal combustion engines is made towards meeting of the increasingly stringent requirements for toxic exhaust emissions, reduction of fuel consumption, and preservation of Earth's natural resources. The problem to solve in modern diesel engines is the emission of toxic compounds. One way to reduce emissions is to use a catalytic converter positioned directly in the combustion chamber of an internal combustion engine. The aim of this analysis is assessment of toxic emissions of a diesel engine with an internal catalyst. Qualitative assessment of engine emissions was determined by comparing test results of an engine with ceramic-ally coated valves against one with just conventional valves (commercial valves - without a ceramic coating). The study utilized a fourcylinder 1.9 TDI VW engine. It was expected that the use of glow plugs with an active coating would reduce the release of toxic compounds.
Źródło:
Journal of KONES; 2014, 21, 1; 99-106
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ozonization influence on energy and ecological characteristics of locomotive diesel engine
Autorzy:
Golubenko, A.
Nozhenko, E.
Mogila, V.
Vasiljev, I.
Ignatiev, O.
Powiązania:
https://bibliotekanauki.pl/articles/375037.pdf
Data publikacji:
2008
Wydawca:
Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:
diesel engine
fuel gas
Opis:
The results of preliminary experimental research of ozonized fuel influence on working characteristics of diesel engine. The decrease of fuel consumption on 1,1% and exhaust opacity lessening of exhaust gases by working on ozonized fuel on 12-17% are discovered.
Źródło:
Transport Problems; 2008, 3, 4; 39-46
1896-0596
2300-861X
Pojawia się w:
Transport Problems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Use of lube oils in terms of the structural composition of marine piston engines
Autorzy:
Łosiewicz, Z.
Kamiński, W.
Powiązania:
https://bibliotekanauki.pl/articles/359391.pdf
Data publikacji:
2013
Wydawca:
Akademia Morska w Szczecinie. Wydawnictwo AMSz
Tematy:
diesel engine
lube oil
diagnostics
Opis:
Lube oil is applied in a number of its functional solutions for modern engines. Therefore, when application changes are implemented, simultaneously, the existing diagnostic methods should be improved. The authors have attempted to analyze the existing trends of lube oil application as a diagnostic tool and have proposed their solution.
Źródło:
Zeszyty Naukowe Akademii Morskiej w Szczecinie; 2013, 36 (108) z. 2; 114-117
1733-8670
2392-0378
Pojawia się w:
Zeszyty Naukowe Akademii Morskiej w Szczecinie
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Thermal loads of engines for different properties of commercial fuels
Autorzy:
Sroka, Z. J.
Reksa, M.
Miksiewicz, K.
Powiązania:
https://bibliotekanauki.pl/articles/243852.pdf
Data publikacji:
2008
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
thermal loads
fuels
Opis:
It is oblivious, various properties of fuels cause different thermal loads of engines. Question is, how big is this effect and what fuel compound and its property play insignificant part. This paper is focused on problem of quality of diesel commercial fuels in Polish market and it is a challenge to find answer for question mentioned above. The academic staff from Wroclaw University of Technology organized tests with different commercial fuels. Chemical and physical properties of these fuels were studied and used for investigation to define relationships between them and thermal load during simulation process. All researches were done in the lab of Division of Motor Vehicles and Internal Combustion Engines at the Wroclaw University of Technology. Tests have showed differences in chemical and physical properties of fuels, but there is no statistics effect on engine parameters. Results have not also pointed any important differences in thermal loads of engine VW1,9 TDI and its components according to different physical and chemical properties of tested fuels. It is probably because there are differences of calorific values from one side but from other hands various density and specific fuel consumption compensated these differences. To burn unit of fuel contains higher level of oxygen, engine needs lower amount of air, so it gives, for the same fuelling system, lean mixture. It causes higher temperature of exhaust gases and a bit higher exhaust losses
Źródło:
Journal of KONES; 2008, 15, 2; 463-467
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wear profile of the cylinder liner in a motor truck diesel engine
Autorzy:
Koszałka, G.
Niewczas, A.
Powiązania:
https://bibliotekanauki.pl/articles/244295.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
wear
cylinder liner
Opis:
The paper presents results of investigation of cylinder liners wear. The investigation was carried out on diesel engines during long lasting operation in 5 motor trucks. Cylinder diameters were measured in two perpendicular planes on four depths using 2-point bore gauge, after removal of the cylinder head. Measurements were made every 50 000 km of vehicle mileage. Such methodology of measurements enabled to determine time course and wear profile of the cylinder liners (wear value in relation to the direction and height of the liner). It was stated that increments of diameter during the first period of operation are several times higher than during the later periods, when the wear intensity is constant. It was also found that wear of the cylinder liner in the plane perpendicular to the engine axis is bigger than in the parallel plane, and that wear in the upper part of the liner is twice as big as in its middle part. Measurement scheme for the cylinder liner; histogram of cylinder liner diameters obtained in measurements after the technological running-in of the engine after mileage of 0, 50,000 km, 150,000 km and 250,000 km, wear profiles of cylinder liners in the two directions at different vehicle mileages are presented in the paper. Estimated profiles of the cylinder liner wear will be used as input data for the calculations of the blowby intensity with the use of mathematical model of PRC set.
Źródło:
Journal of KONES; 2007, 14, 4; 183-190
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Correlation between cylinder pressure and noise emissions from diesel engines
Autorzy:
Narayan, S.
Powiązania:
https://bibliotekanauki.pl/articles/248079.pdf
Data publikacji:
2015
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine noise
acoustics
vibrations
Opis:
The aim of this paper is to study the results obtained from a common rail dual cylinder diesel engine. Modern methodology involves the use of non-intrusive techniques of cylinder pressure measurements using sensors installed in the engine test rig. This work analysis the experiments carried out on a dual cylinder diesel engine .The results obtained are analysed to develop the relationship between the cylinder pressure levels and noise emitted from engine. Multiple injection process in diesel engines; engine test rig setup; cylinder pressure levels, noise levels; PSD plots for cylinder pressure signals, PSD plots for cylinder noise signal, PSD plots for cylinder pressure derivative signals for 1600, 2000 RPM; in cylinder pressure spectrogram at 1600 RPM, 100% load; motored cylinder pressure spectrogram at 1600 RPM; cylinder pressure and noise emission spectrograms; piston slap noise emissions, valve noise emissions and valve noise emissions spectrograms; and correlation between cylinder pressure and radiated noise levels are presented in the paper.
Źródło:
Journal of KONES; 2015, 22, 1; 243-254
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Alternative fuels for diesel engines
Autorzy:
Caban, J.
Gniecka, A
Holeša, L.
Powiązania:
https://bibliotekanauki.pl/articles/103241.pdf
Data publikacji:
2013
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
biofuel
diesel engine
eco-fuels
Opis:
This paper presents the development and genesis of the use of alternative fuels in internal combustion ignition engines. Based on the analysis of the literature, this article shows various alternative fuels used in Poland and all over the world. Furthermore, this article describes the research directions for alternative fuels use in road transport powered by diesel engines.
Źródło:
Advances in Science and Technology. Research Journal; 2013, 7, 20; 70-74
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A comparative assessment of operating characteristics of a diesel engine using 20% proportion of different biodiesel diesel blend
Autorzy:
Ramalingam, Senthil
Rajendran, Silambarasan
Ganesan, Pranesh
Powiązania:
https://bibliotekanauki.pl/articles/243735.pdf
Data publikacji:
2019
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
biodiesel diesel blend
performance
emission
diesel engine
Opis:
The objective of the present work is to find out the viable substitute fuel for diesel and control of pollutants from compression ignition engines. Therefore, in this present investigation an attempt has been made to study the effect of 20% proportion of five different biodiesel diesel blend in diesel engine. The 20% proportion of biodiesel such as Jatropha, Pongamia, Mahua, Annona and Nerium and 80% of diesel and it is denoted as J20, P20, M20, A20 and N20 are used in the present investigation. The experimental results showed that the brake thermal efficiency of the different biodiesel blend is slightly lower when compared to neat diesel fuel. However, N20 blend, have shown improvement in performance and reduction in exhaust emissions than that of other biodiesel diesel blends. From, the experimental work, it is found that biodiesel can be used up to 20% and 80% of diesel engine without any major modification. The conducted experiments were conducted on a four cylinder four stroke DI and turbo charged diesel engine using biodiesel blends of waste oil, rapeseed oil, and corn oil with normal diesel. The peak cylinder pressure of the engine running with bio diesel was slightly higher than that of diesel. The experiments were conducted on a four cylinder four stroke diesel engine using bio diesel made from corn oil.
Źródło:
Journal of KONES; 2019, 26, 1; 127-140
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
An effect of physical and chemical properties of commercial diesel fuels on engine parameters
Autorzy:
Sroka, Z. J.
Reksa, M.
Kułażyński, M.
Powiązania:
https://bibliotekanauki.pl/articles/242752.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
diesel engine
engine fuels engine performances
Opis:
This paper is focused on problem of quality of diesel commercial fuels in Polish market and an effect of their properties as well on engine parameters as environment The academic staff from Wrocław University of Technology put the own experience to the huge discussion by making research in the Wroclaw-city, where some probes of fuels were taken from six different commercial fuel stations. Chemical and physical properties of fuels were checked. A real diesel engine VW 1,9 TDI was investigated in university lab of Division of Motor Vehicles and Internal Combustion Engines. Typical engine performances were built including power, torque, fuel consumption, toxicity levels due to different fuels. The IC engine on the test bench, oxygen content in fuels, example of full load performance of VW1,9 TDI for fuel Bio D20-type, differences of mean effective pressure for different fuels, differences of carbon monoxide in exhaust for different fuels, differences of nitric oxides in exhaust for different fuels, differences of smog level in exhaust for different fuels, differences of heat release for different fuels, relation between engine torque and oxygen content in fuels vs. engine rotation are presented in the paper.
Źródło:
Journal of KONES; 2007, 14, 4; 447-452
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Stan diagnostyki technicznej okrętowych silników tłokowych
The status of the marine diesel engines technical diagnostic
Autorzy:
Witkowski, K.
Powiązania:
https://bibliotekanauki.pl/articles/328463.pdf
Data publikacji:
2005
Wydawca:
Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:
diagnostyka eksploatacyjna
silniki okrętowe
diagnozowanie silników
operation diagnostic
marine diesel engine
diesel engine diagnostic
Opis:
W artykule przedstawiono okrętowy silnik tłokowy jako złożony obiekt diagnostyki. Podzielono go na układy funkcjonalne. Taka dekompozycja obiektu pozwala rozwiązywać zadania diagnostyczne w strukturach zdecentralizowanych. Omówiono możliwości diagnozowania silników okrętowych w warunkach eksploatacyjnych. Przedstawiono szereg przykładów wdrożonych do eksploatacji systemów diagnostycznych.
In his paper a marine diesel engine Has been described as a complex technical object. Divided into functional blocks. Such decomposition allows to solve diagnostic problems in decentralized structures. Also the possibilities of marine engine diagnostic have been described with a series of examples of systems already in use.
Źródło:
Diagnostyka; 2005, 34; 85-92
1641-6414
2449-5220
Pojawia się w:
Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A fatigue testing method of wet cylinder liner of diesel engines
Autorzy:
Kaźmierczak, A.
Kolanek, Cz.
Powiązania:
https://bibliotekanauki.pl/articles/247871.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
diesel engine
cylinder liner
fatigue
Opis:
It has been agreed to call the loads changing with time and acting in most varied constructional arrangements as well as the stresses accompanying them changeable or cyclic. Changeable stresses produce in the material a very complex entanglement of phenomena and changes depending on the value of those stresses and on the number of cycles. These are fatigue phenomena and changes. They develop successively till the element has been destroyed. This is called the element material fatigue. Thus changing loads and stresses are also called fatigue loads and stresses. The purpose of the presented work was to develop a method of comparative investigations for wet replaceable sleeves in direct contact with coolant that have been submitted to technological treatment of sub-edge zone material strengthening. The source of loads is a cyclically occurring normal component of gas and mass forces in the cylinder. The frequency of changes is a derivative of the number of strokes in the engine run and of the rotational speed of the crankshaft. Fatigue loads can be the reason why cylinder liner cracks in the edge zone. The results of the fatigue testing of the technological process of strengthening the cylinder lines sub-edge zone on crack sensitivity shows differences in the behaviour of particular samples, depending on the parameters of strengthening. The fatigue testing method can be used to evaluate the technological process of cylinder liner.
Źródło:
Journal of KONES; 2007, 14, 3; 287-290
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Nowe wyzwanie dla silników Diesla - helikopter!
New challenge for the Diesel engine - the helicopter!
Autorzy:
Pągowski, Z. T.
Powiązania:
https://bibliotekanauki.pl/articles/213755.pdf
Data publikacji:
2008
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
silnik Diesla
helikopter
diesel engine
helicopters
Opis:
Maksimum światowego wydobycia ropy naftowej ocenia się na rok 2020 i nikt nie ma wątpliwości, że tania ropa się skończyła. Dnia 2 stycznia 2008 roku cena baryłki ropy przekroczyła 100 USD! W ślad za wzrostem cen ropy wzrastają ceny paliw lotniczych. Zmienia się także spojrzenie na system transportu gwałtownie oddziaływujący na środowisko naturalne. Dynamicznie rozwijające się lotnictwo potrzebuje paliw o zmodyfikowanych własnościach i stabilnych źródłach. Wzrasta zainteresowanie użyciem General Aviation, zainteresowanie paliwami alternatywnymi i nowymi ekologicznymi i ekonomicznymi sposobami napędu. Na celowniku zastosowania pojawia się ponownie w historii lotnictwa silnik Diesla, który zaczyna być obiektem zainteresowania w lekkich samolotach i helikopterach. Różni się on oczywiście znacznie, w wyniku ewolucji jaką przeszedł na przestrzeni lat w komunikacji samochodowej i znajduje znowu pierwsze zastosowanie w konstrukcjach samolotów, helikopterów od konstrukcji bezpilotowych po lekkie śmigłowce. W artykule omówione zostały silniki aktualnie wkraczajace na ten rynek zastosowaii obejmujące konstrukcje zarówno europejskie jak np. silniki Thielert zbudowane na bazie 4-suwowych silników samochodowych Mercedesa, jak i spoza Europy, jak np. 2-suwowe specjalnie konstruowane jako lotnicze silniki Delta Hawk, z którymi autor publikacji zapoznał się w czasie pobytu w firmie Delta Hawk w USA. Przedstawione zostaną również idee ewolucyjnego rozwoju silników typu "emission close to zero" w oparciu o tzw. jednolite paliwo o nowych zmodyfikowanych własnościach w oparciu tzw. zintegrowany proces termochemiczny oraz najnowsze rewolucyjne rozwiązania.
Maximum of world oil extraction is estimated to be in the year of 2020 and no one can doubt that the cheap oil is over. On 2 January 2008 the price per barrel of oil exceeded $100! In the wake of high fuel prices the aviation fuel prices are rising. Changes will also look at the transport system is rapidly affecting the environment. Dynamically developing aviation needs fuel with modified properties and stable sources. There is an increasing interest in General Aviation in their use, interest in alternative fuels and new environmental and economic means of propulsion. Targeted application appears again in the history of aviation — the diesel engine, which becomes the object of interest in light airplanes and helicopters. It obviously differs considerably as a result of what has evolved over the years in the car and communication is again the first in the construction of airplanes, helicopters, from the pilotless designs to design of the light helicopters. The engines currently being discussed in this paper and entering into aircraft market applications, including both: the European structures such as the Thielert engines built on an automotive engine four stroke Mercedes, as well as outside Europe, such as two-stroke, specially designed as an aircraft Delta Hawk engine, with which the author met during stay at Delta Hawk firm in the US. Presented will be also the ideas about evolutionary development engines such as "emission close to the zero" on the basis of the so-called the new, uniform modified fuel properties on the basis of so-called integrated termochemical process and the latest revolutionary solutions.
Źródło:
Prace Instytutu Lotnictwa; 2008, 3-4 (194-195); 74-82
0509-6669
2300-5408
Pojawia się w:
Prace Instytutu Lotnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Vibro-acoustic methods in marine diesel engines diagnostics
Autorzy:
Lus, T.
Powiązania:
https://bibliotekanauki.pl/articles/245521.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
turbocharger
diagnostics
vibration
Opis:
Vibro-acoustic diagnostic methods which are used on marine high-speed diesel engines with turbochargers are presented in this paper. Vibration and acoustic signals generated by turbochargers need different signal processing methods to be effective and faultless in turbochargers diagnostics. Diagnostic methods which based on vibration and acoustic signals analysis are sensitive on engine load and speed changes. Methods presented in this paper based on vibration and acoustic signals processing in time and frequency domain. Using this methods checking technical condition of the turbochargers and its rotors and bearings without stopping the engine and dismantling it is possible. Examples of radial-flow rotor turbine overgrown by carbon soot and axial-flow rotor turbine without turbine blades, sound intensity level of turbocharger and acoustic spectrum of turbocharger in octave mode acoustic spectrum of turbocharger in octave mode for two different technical conditions, acoustic and vibration signal spectrum of the turbocharger, vibration acceleration amplitude of first harmonic for three turbochargers, values of harmonic vibrations of accelerations equivalent of turbine blades number, amplitude of vibrations accelerations in frequency domain for turbocharger in good and bad technical conditions are presented in the paper.
Źródło:
Journal of KONES; 2011, 18, 3; 203-210
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Engine fuel characterisation through ultraviolet absorption spectra
Autorzy:
Baszanowska, E.
Otremba, Z.
Powiązania:
https://bibliotekanauki.pl/articles/245537.pdf
Data publikacji:
2017
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
fuel
spectroscopy
absorptivity
diesel engine system
Opis:
In the article, light absorption properties of the fuel oil are considered with a view to create basis for establish optical indicator of the type and quality of this kind of crude oil derivative, in this case the Diesel fuel. The organic solvent – n-hexane – was chosen as a solvent to prepare samples of dilutions of Diesel fuel in several oil concentration. Spectrophotometer Aqualog Horiba were applied to record the absorbance spectra in the ultraviolet and visual range of the light (from 240 to 600 nm) for each previously prepared samples. Obtained results allow concluding that the changes of absorbance occur primarily in the wavelength range from 240 nm to 355 nm. Moreover, the absorbance spectra are characterized by the characteristic sharp peak located at 270 nm for excitation wavelength. Spectra of absorbance were converted to spectra of absorption coefficient based on Lambert-Beer law. Due to the independence the absorption coefficient from the fuel concentration, this parameter could be used as a potential indicator to access composition and quality Diesel fuel used in the diesel engine system. Therefore, preliminary tests allow concluding that absorption coefficient for selected wavelength located at 270 nm could be a sensitive indicator for quick access to fuel quality.
Źródło:
Journal of KONES; 2017, 24, 3; 15-19
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies