Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Szymczyk, E." wg kryterium: Autor


Tytuł:
Wpływ zmiany użytkowania gruntu na jakość wód obszaru zdrenowanego w Lidzbarku Warmińskim
Influence of the change of using soil to the water quality on the drainage systems in object Lidzbark Warmiński
Autorzy:
Cymes, I
Szejba, D.
Szymczyk, S
Świtajska, I
Olba-Zięty, E
Powiązania:
https://bibliotekanauki.pl/articles/949961.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
jakość wody
wody gruntowe
odpływy drenarskie
oczka wodne
water quality
groundwater
outflows from drainage system
small ponds
Opis:
Badaniami objęto wody gruntowe, odpływające siecią drenarską oraz zretencjonowane w oczku wodnym zlokalizowanym na obszarze użytkowanym rolniczo, w części działu drenarskiego obiektu Lidzbark Warmiński na Równinie Sępopolskiej. Badania wykonywano w latach 1998–2000 po zdrenowaniu użytków zielonych oraz w latach 2008–2010, po transformacji gruntu obsianego pszenicą ozimą. Celem badań było określenie zmian jakości wód po zmianie sposobu użytkowania terenu. Badania wykazały, że na skutek zmiany sposobu użytkowania ziemi i zaniechaniu nawożenia mineralnego w oczkach wodnych stwierdzono zmniejszenie stężeń większości składników mineralnych, oraz zwiększenie wartości pH, stężeń potasu, magnezu siarczanów i wodorowęglanów. W wodach gruntowych zanotowano wzrost stężeń mineralnych form azotu, fosforu fosforanowego, potasu, magnezu oraz żelaza ogólnego i wodorowęglanów, zaś zmniejszenie stężeń wapnia, sodu, siarczanów i chlorków. W wodzie drenażowej nastąpił wzrost stężeń większości oznaczanych składników, oprócz azotu amonowego i chlorków
The study included groundwater outflow drainage systems and collected in the pond located at the agricultural use area in the portion of the drainage facility Lidzbark Warminski located on the Sępopolska Plain. The study was performed in two periods: the first one was in 1998–2000 (just after was made drainage), in which the discussed area was used as pasture, and the second in 2008–2010, in which after plowed of the soil was cultivated winter wheat. The aim of the study was to determine changes in water quality after the change of the way of land use. Examinations showed that as a result of the change of the way of using the area and ceasing of mineral fertilizing in waters of the pond was a reduction in the concentrations of the most mineral components, but an increase of pH reaction and concentrations of potassium, magnesium of sulfates and bicarbonates. In groundwaters observed increased the content of concentrations of mineral forms of nitrogen, phosphatic phosphorus, potassium, magnesium, general iron and bicarbonates, and a reduction in the concentrations of calcium, sodium, sulfates and chlorides. However in the water which outflow from drainage pipelines system from the research area was an increase of concentrations most of the determined substances, apart from ammonia nitrogen and chlorides.
Źródło:
Inżynieria Ekologiczna; 2014, 37; 80-88
2081-139X
2392-0629
Pojawia się w:
Inżynieria Ekologiczna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numeryczne modelowanie zagadnienia kontaktu w procesie spęczania nitu
Numerical modelling of a contact problem in the rivet upsetting process
Autorzy:
Derewońko, A.
Szymczyk, E.
Jachimowicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/208471.pdf
Data publikacji:
2006
Wydawca:
Wojskowa Akademia Techniczna im. Jarosława Dąbrowskiego
Tematy:
MES (metoda elementów skończonych)
proces nitowania
zagadnienie kontaktu
połączenia nitowe
FEM
riveting process
contact problem
riveted joint
Opis:
Celem pracy jest dobór modelu numerycznego (właściwej siatki elementów skończonych) zapewniającego prawidłowe odwzorowanie współpracy kontaktujących się powierzchni nitu i blachy w procesie spęczania trzpienia nitu. Stanowi ona jeden z etapów badania lokalnych zjawisk fizycznych w połączeniach nitowych lotniczych konstrukcji cienkościennych [1-8]. Analizy z uwzględnieniem zagadnienia kontaktu i dużych odkształceń wykonano metodą elementów skończonych w programie MSC.Marc. Wyniki obliczeń numerycznych porównano z wartościami sił i naprężeń oszacowanymi analitycznie dla spęczanego swobodnego walca. Uzyskane numerycznie rozkłady naprężeń i odkształceń są zgodne z prezentowanymi w literaturze [13], co wskazuje, że proces zakuwania trzpienia nitu został odwzorowany poprawnie. Deformacje powierzchni kontaktu na granicy nitu i blachy wykazują dużą wrażliwość na parametry siatki elementów skończonych. Właściwy sposób podziału współpracujących brył na elementy skończone pozwala uniknąć wzajemnego przenikania węzłów, a tym samym niefizycznych koncentracji naprężeń w obszarze kontaktu.
The paper deals with numerical simulation of rivet upsetting in a hole. The work is aimed at a choice of numerical model (proper finite element mesh) that ensures suitable behaviour of the rivet and sheet hole surfaces during rivet's upsetting process. This is preliminary stage of an analysis of the local physical phenomena in the riveted joints of an aircraft structure. A contact problem and large strains are taken into consideration in FEM analysis performed with MARC code. Numerical results are compared with analytical estimations for upsetting a cylindrical specimen. Numerical stress and strain fields show that squeezing the rivet shank is correctly described. The deformations of contact surface between the rivet and the hole are sensitive on finite element mesh parameters. Due to appropriate meshing of the mating components, mutual node penetration and consequently, non-physical stress concentration on the contact surfaces can be avoided.
Źródło:
Biuletyn Wojskowej Akademii Technicznej; 2006, 55, 4; 89-100
1234-5865
Pojawia się w:
Biuletyn Wojskowej Akademii Technicznej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on Possible Replacement of the Aluminum Spar with a Composite Structure Illustrated with the Case of Agricultural Aircraft
Autorzy:
Fałek, M.
Szymczyk, E.
Jachimowicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/98018.pdf
Data publikacji:
2017
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
composite structure
agricultural aircraft
airplane wing
Opis:
Composite materials are increasingly being used in aviation. Specific stiffness and strength of composite materials (especially CFRP laminate, sandwich structure) are higher compared to metal alloys. They are beneficial features of materials used in aviation. Mass reduction of aircraft structures (e.g. due to the use of composite materials) contributes to an aircraft’s better performance in terms of its range, top speed and ceiling and consequently causes an increase in airplanes capacity. Moreover, the use of high-strength and lightweight materials in aviation contributes to longer life time and lower exploitation costs. The aim of the paper was the study the possibilities of replacing the aluminum spar of an airplane wing with a composite structure. In order to compare the mass and strength of the aluminum with the composite spar, the global shell and local solid models were created and finite elements analysis was performed. The analysis was carried out for the front spar of the wing of the agricultural aircraft PZL-106.
Źródło:
Fatigue of Aircraft Structures; 2017, 9; 85-99
2081-7738
2300-7591
Pojawia się w:
Fatigue of Aircraft Structures
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modele globalne i lokalne MES w analizie struktur lotniczych na przykładzie fragmentu skrzydła samolotu PZL M28 Skytruck
Global and local FE models for aircraft structures analyses based on example of the PLZ M28 Skytruck airplanes wing part
Autorzy:
Jachimowicz, J.
Szymczyk, E.
Sławiński, G.
Derewońko, A.
Wronicz, W.
Powiązania:
https://bibliotekanauki.pl/articles/208840.pdf
Data publikacji:
2010
Wydawca:
Wojskowa Akademia Techniczna im. Jarosława Dąbrowskiego
Tematy:
struktury lotnicze
połączenie nitowe
proces zakuwania
modele MES
pola naprężeń resztkowych
riveted joint
mushroom rivet
FEM local models
stress and strain fields
Opis:
W niniejszym artykule na wstępie przedstawiono globalne analizy statyczne MES struktury fragmentu skrzydła samolotu PZL M28 Skytruck. W dalszej części pracy zamieszczono kolejno modele lokalne o różnym stopniu szczegółowości, umożliwiające analizy MES obszarów konstrukcji skrzydła z uwzględnieniem połączeń nitowych, analizy poszczególnych szwów nitowych, a w końcu analizy pojedynczych nitów. Omawiane modele lokalne poza warunkami brzegowymi wynikającymi z modeli globalnych i obciążeniami ogólnymi samolotu uwzględniają wybrane czynniki materiałowe i technologiczne oraz ich wpływ na stan przemieszczeń i naprężeń wokół nitu. Na końcu artykułu przedstawiono symulację procesu nitowania nitu grzybkowego w wyniku której uzyskano rozkład naprężeń resztkowych wokół nitu.W analizach wykorzystano systemy MSC Nastran, Marc i Ansys, a zakres analiz obejmował materiały sprężysto-plastyczne oraz sformułowania dużych przemieszczeń i odkształceń, a także wielopłaszczyznowy kontakt powierzchniowy.
The paper deals with the analysis of residual stress and strain fields in a riveted joint. This stage of study concerns improving the fatigue performance of riveted joints in an airframe. Riveting, particularly in aviation, is a traditional but still commonly used method of joining sheet metal components. Aircraft structures are thin-walled ones, with coverings made of thin sheets stiffened by stringers, frames or ribs. Sheets are typically assembled by multiple rivet or bolt joints. Rivets and bolts are also used to joint sheets and stiffeners. Therefore fatigue resistance of the aircraft structure depends on tens of thousands or even hundreds of thousands rivet joints, which are used to build it. Global and local numerical models of the joint are considered with regard to the aim introduced in the paper. Numerical FE simulations of upsetting process are carried out using the NASTRAN and MARC code. Three-dimensional numerical models are used to determine the resulting stress and strain fields at the mushroom rivet and around the hole. This type of a problem requires the use of contact between the elements assembled and non-linear geometric and elasto-plastic multilinear material models to simulate behaviour of the rivet and sheets. The influence of the squeezing force on strain and stress states is studied. A certain solution to the problem connected with non-uniform stress distribution in the rivet hole is proposed and analysed.
Źródło:
Biuletyn Wojskowej Akademii Technicznej; 2010, 59, 1; 35-59
1234-5865
Pojawia się w:
Biuletyn Wojskowej Akademii Technicznej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zjawisko frettingu w konstrukcjach lotniczych
Fretting phenomenon in aircraft structure
Autorzy:
Jachimowicz, J.
Kaniowski, J.
Kozłowski, P.
Moneta, G.
Szymczyk, E.
Powiązania:
https://bibliotekanauki.pl/articles/213371.pdf
Data publikacji:
2010
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
konstrukcje lotnicze
zjawisko frettingu
zmęczenie cierne
aircfart structure
fretting phenomenon
friction fatigue
Opis:
Zmęczenie cierne często jest przyczyną przedwczesnego zniszczenia zmęczeniowego konstrukcji. Dla ilustracji tego zjawiska wybrano przykłady obiektów lotniczych, których trwałość została istotnie zmniejszona z powodu wystąpienia tego efektu. Są to między innymi struktura skrzydła samolotu i wirnik silnika lotniczego.
Friction fatigue is often a cause of premature fatigue destruction of a structure. The examples of aviation objects, which fatigue durability was reduced because of this effect, were chosen to illustrate this phenomenon. These include a structure of an aircraft wing and a rotor of an air engine.
Źródło:
Prace Instytutu Lotnictwa; 2010, 4 (206); 36-58
0509-6669
2300-5408
Pojawia się w:
Prace Instytutu Lotnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The chemical digestion of Ti6Al7Nb scaffolds produced by Selective Laser Melting reduces significantly ability of Pseudomonas aeruginosa to form biofilm
Autorzy:
Junka, A. F.
Szymczyk, P.
Secewicz, A.
Pawlak, A.
Smutnicka, D.
Ziółkowski, G.
Bartoszewicz, M.
Chlebus, E.
Powiązania:
https://bibliotekanauki.pl/articles/307092.pdf
Data publikacji:
2016
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
technologia SLM
Pseudomonas aeruginosa
skafoldy
modyfikacja powierzchni
Ti-6Al-7Nb
SLM technology
scaffolds
surface modification
Opis:
In our previous work we reported the impact of hydrofluoric and nitric acid used for chemical polishing of Ti-6Al-7Nb scaffolds on decrease of the number of Staphylococcus aureus biofilm forming cells. Herein, we tested impact of the aforementioned substances on biofilm of Gram-negative microorganism, Pseudomonas aeruginosa, dangerous pathogen responsible for plethora of implant-related infections. The Ti-6Al-7Nb scaffolds were manufactured using Selective Laser Melting method. Scaffolds were subjected to chemical polishing using a mixture of nitric acid and fluoride or left intact (control group). Pseudomonal biofilm was allowed to form on scaffolds for 24 hours and was removed by mechanical vortex shaking. The number of pseudomonal cells was estimated by means of quantitative culture and Scanning Electron Microscopy. The presence of nitric acid and fluoride on scaffold surfaces was assessed by means of IR and rentgen spetorscopy. Quantitative data were analysed using the Mann–Whitney test (P ≤ 0.05). Our results indicate that application of chemical polishing correlates with significant drop of biofilm-forming pseudomonal cells on the manufactured Ti-6Al-7Nb scaffolds ( p = 0.0133, Mann–Whitney test) compared to the number of biofilm-forming cells on non-polished scaffolds. As X-ray photoelectron spectroscopy revealed the presence of fluoride and nitrogen on the surface of scaffold, we speculate that drop of biofilm forming cells may be caused by biofilm-supressing activity of these two elements.
Źródło:
Acta of Bioengineering and Biomechanics; 2016, 18, 1; 115-120
1509-409X
2450-6303
Pojawia się w:
Acta of Bioengineering and Biomechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Eksperymentalna i numeryczna analiza procesu instalacji nitu
Experimental and numerical analysis of a rivet installation process
Autorzy:
Korbel, A.
Szymczyk, E.
Skorupa, A.
Powiązania:
https://bibliotekanauki.pl/articles/211311.pdf
Data publikacji:
2013
Wydawca:
Wojskowa Akademia Techniczna im. Jarosława Dąbrowskiego
Tematy:
połączenia nitowe
nity lotnicze
siła zakuwania nitu
ekspansja otworu nitowego
naprężenia resztkowe
MES (metoda elementów skończonych)
riveted joints
aircraft rivets
squeeze force
hole expansion
residual stresses
FEM
Opis:
W artykule przedstawiono wyniki badań eksperymentalnych oraz analiz numerycznych MES związane z procesem zakuwania nitu. Analizie poddano stosowane w polskim przemyśle lotniczym nity z łbem kulistym z materiału PA24 oraz blachy ze stopu D16CzATW. Zbadano, jak siła nitowania wpływa na charakterystyczne wymiary zakuwki oraz ekspansję otworu nitowego, a następnie uzyskane wyniki porównano z wynikami analiz MES. Ponieważ dotychczas stosowane metody pomiaru ekspansji otworu mogą być obarczone błędem, opracowano własną metodę pomiaru, cechującą się większą dokładnością. Zbadano, jak przyjęty w analizach MES model materiału nitu wpływa na jakość otrzymywanych wyników. Wykazano, że wierne odtworzenie procesu nitowania w MES wymaga odpowiedniego zdefiniowania modeli materiałowych stosowanych w tych analizach. Ponadto określono wpływ siły zakuwania nitu na rozkład oraz wielkość resztkowych naprężeń promieniowych i obwodowych wokół otworu nitowego.
Experimental results and numerical FE analysis related to the riveting process are considered in the paper. The research has focused on the round head rivet and D16CzATW sheet material used by Polish aircraft manufacturers. The effect of rivet squeeze force on the rivet driven head dimensions and rivet hole expansion was experimentally investigated and the results were compared with the FE results. In view of an insufficient accuracy of hole expansion measurement methods used so far, a novel more accurate measurement technique developed by the present authors has been applied. FE results were obtained for various models of the rivet material. It was shown that an adequate numerical modelling of the rivet installation is conditioned by appropriate assumptions about the constitutive characteristics of the rivet material. The impact of the squeeze force on distributions and values of residual stresses generated by riveting was also determined.
Źródło:
Biuletyn Wojskowej Akademii Technicznej; 2013, 62, 2; 181-200
1234-5865
Pojawia się w:
Biuletyn Wojskowej Akademii Technicznej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zastosowanie technologii Rep-Rap do wytwarzania funkcjonalnych struktur z PLA
PLA scaffolds manufactured by Rep-Rap technology
Autorzy:
Mazgajczyk, E.
Szymczyk, P.
Chlebus, E.
Powiązania:
https://bibliotekanauki.pl/articles/99137.pdf
Data publikacji:
2014
Wydawca:
Politechnika Śląska. Katedra Biomechatroniki
Tematy:
RepRap
skafold
PLA
szybkie prototypowanie
scaffold
rapid prototyping
Opis:
W niniejszej pracy skupiono się na omówieniu technologii addytywnej, jaką jest technologia „Rep-Rap”, w kontekście zastosowania jej w inżynierii tkankowej. Określono parametry mające największy wpływ na jakość wytwarzanych elementów. Wykazano wpływ temperatury głowicy na geometrię wytwarzanej struktury. Materiał, który został wykorzystany w procesie to biodegradowalny oraz biokompatybilny polimer (PLA-Polilaktyd), powszechnie stosowany w inżynierii regeneracyjnej.
This study describes one of the additive technology, which is RepRap technique, in the context of its application in tissue engineering. The parameters, which have to greatest impact on the quality of printed structures, were specified. The purpose of present work is showing the influence of temperature of the plotting head on the scaffold geometry. The material that was used in the process are biodegradable and biocompatible polymer (PLA-polylactide), commonly used in tissue engineering.
Źródło:
Aktualne Problemy Biomechaniki; 2014, 8; 109-114
1898-763X
Pojawia się w:
Aktualne Problemy Biomechaniki
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The lichen family Parmeliaceae in Poland. III. Parmelia serrana, new to Poland
Autorzy:
Ossowska, E.
Szymczyk, R.
Bohdan, A.
Kukwa, M.
Powiązania:
https://bibliotekanauki.pl/articles/56830.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Botaniczne
Tematy:
lichen
Parmeliaceae
Polska
Parmelia serrana
new species
parmelioid lichen
chemotaxonomy
distribution
Opis:
Parmelia serrana A. Crespo, M.C. Molina & D. Hawksw. is reported here for the first time from Poland. The species has been recorded from more than 20 localities and exclusively on the bark of trees. Its general distribution, habitat requirements, morphology, secondary chemistry are provided and the differences between this species and similar taxa, especially P. saxatilis and P. ernstiae, are discussed.
Źródło:
Acta Societatis Botanicorum Poloniae; 2014, 83, 1
0001-6977
2083-9480
Pojawia się w:
Acta Societatis Botanicorum Poloniae
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Ability of Leaves and Rhizomes of Aquatic Plants to Accumulate Macro- and Micronutrients
Autorzy:
Parzych, A. E.
Cymer, M.
Jonczak, J.
Szymczyk, S.
Powiązania:
https://bibliotekanauki.pl/articles/123566.pdf
Data publikacji:
2015
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
bottom sediments
Glyceria maxima
Phragmites australis
Phalaris arundinacea
Typha latifolia
accumulation of nutrients
Opis:
The samples of macrophytes and bottom sediments originated from the littoral zone of the Słupia River were collected in summer 2013. The aim of this study was to compare the properties of the accumulation of leaves and rhizomes of Glyceria maxima, Phragmites australis, Typha latifolia and Phalaris arundinacea for macro- and micronutrients. The largest quantities of macroelements were found in the leaves of the examined species, and microelements dominated the rhizomes of most examined macrophytes except for Mn in P.australis and T.latifolia. The obtained results show that N and K dominated in the leaves of P.arundinacea, P and Mg in the leaves of P.australis, and Ca in the leaves of G.maxima. The largest quantities of N, P and K were cumulated in the rhizomes of P.arundinacea, while Mg and Ca in the rhizome of T.latifolia. The leaves of aquatic plants accumulated from 1354.9 mmolc·kg-1 (T.latifolia) to 1844.0 mmolc·kg-1 (P.arundinacea), and rhizomes from 985.8 mmolc·kg-1 (G.maxima) to 1335.2 mmolc·kg-1 (P.arundinacea) of all the analyzed components. In these species of macrophytes lower accumulated value of the sum of macro- and microelements were found in the rhizomes. The share of nitrogen was 42.4–59.8% of this amount, phosphorus 4.3–8.6%, potassium 22.8–35.1%, calcium from 2,6% to 12.4%, magnesium 3.0–7.5%, and heavy metals were from 0.6% (G.maxima) to 1.2% (T.latifolia) in leaves and from 2.2% (T.latifolia) to 8.7% (G.maxima) in rhizomes.
Źródło:
Journal of Ecological Engineering; 2015, 16, 3; 198-205
2299-8993
Pojawia się w:
Journal of Ecological Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Improvement of barrier properties of glycol modified poly(ethylene terephthalate) based nanocomposites containing graphene derivatives forms
Poprawa właściwości barierowych nanokompozytów polimerowych opartych na modyfikowanym poli(tereftalanie etylenu) z dodatkiem pochodnych grafenu
Autorzy:
Paszkiewicz, S.
Szymczyk, A.
Pawlikowska, D.
Irska, I.
Piesowicz, E.
Jotko, M.
Lisiecki, S.
Bartkowiak, A.
Sieradzka, M.
Fryczkowski, R.
Kochmańska, A.
Kochmański, P.
Rosłaniec, Z.
Powiązania:
https://bibliotekanauki.pl/articles/946934.pdf
Data publikacji:
2017
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Chemii Przemysłowej
Tematy:
graphene derivatives forms
glycol-modified poly(ethylene terephthalate)
in situ polymerization
barrier properties
pochodne grafenu
poli(tereftalan etylenu) modyfikowany glikolem cykloalifatycznym
polimeryzacja in situ
właściwości barierowe
Opis:
The development and further studies on several types of graphene nanoplatelets (GNP) have enabled manufacture of electrically conductive and reinforced polymer nanocomposites with enhanced gas barrier performance at extremely low loading. Herein, we present the synthesis process, morphology and gas barrier properties of the glycol modified poly(ethylene terephthalate) (PETG) based nanocomposites. For the first time, we compared how different types of GNPs, at the same nanofiller's content of 0.5 wt %, affect the properties of polymer matrix obtained by in situ polymerization.
Opracowano nanokompozyty polimerowe (PETG) na bazie poli(tereftalanu etylenu) (PET) modyfikowanego glikolem cykloalifatycznym z niewielkim dodatkiem wybranych typów płytek grafenowych (GNP). Zbadano morfologię PETG oraz ich właściwości barierowe. Oceniono wpływ dodatku różnego typu nanopłytek grafenowych na właściwości osnowy polimerowej w nanokompozytach otrzymanych metodą polimeryzacji in situ. Stwierdzono, że otrzymane, wzmocnione nanocząstkami grafenu i elektrycznie przewodzące kompozyty PETG odznaczały się zwiększoną barierowością w stosunku do par i gazów.
Źródło:
Polimery; 2017, 62, 11-12; 868-874
0032-2725
Pojawia się w:
Polimery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis and characterization of new poly(ethylene terephthalate)/poly(phenylene oxide) blends
Otrzymywanie i charakterystyka nowych mieszanin poli(tereftalan etylenu)/poli(tlenek fenylenu)
Autorzy:
Paszkiewicz, S.
Irska, I.
Piesowicz, E.
Pilawka, R.
Pawelec, I.
Szymczyk, A.
Gorący, K.
Wielgosz, Z.
Rosłaniec, Z.
Powiązania:
https://bibliotekanauki.pl/articles/946996.pdf
Data publikacji:
2017
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Chemii Przemysłowej
Tematy:
poly(ethylene terephthalate)
poly(phenylene oxide) (PPO)
in situ polymerization
melt blending
phase structure
water absorption
poli(tereftalan etylenu)
poli(tlenek fenylenu)
polimeryzacja in situ
bezpośrednie mieszanie w stanie stopionym
struktura fazowa
chłonność wody
Opis:
Several compositions of poly(ethylene terephthalate) (PET) and poly(phenylene oxide) (PPO) were prepared by two different methods: in situ polymerization (IS-P) and direct mixing in the melt (DM). The existence of phase separation in the obtained PET/PPO systems has been confirmed by calculating the solubility parameter of compounds using Hoy's method. The combination of results obtained with DSC and DMTA points toward a complex morphology of PET/PPO systems.
Z zastosowaniem polimeryzacji in situ (IS-P) i mieszania w stanie stopionym (DM) wytworzono dwie serie mieszanin na bazie poli(tereftalanu etylenu) (PET) oraz poli(tlenku fenylenu) (PPO). Na podstawie obliczonych metodą Hoya współczynników rozpuszczalności poszczególnych składników potwierdzono występowanie separacji fazowej w otrzymanych układach PET/PPO. Technikami różnicowej kalorymetrii skaningowej (DSC) i dynamicznej analizy mechaniczno-termicznej (DMTA) potwierdzono złożoność struktury fazowej uzyskanych układów PET/PPO.
Źródło:
Polimery; 2017, 62, 2; 93-100
0032-2725
Pojawia się w:
Polimery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis and characterization of new reactive polymer blends based on post-consumer glycol-modified poly(ethylene terephthalate) foils and poly(tetramethyleneoxide)
Synteza i charakterystyka nowych reaktywnych mieszanin polimerowych opartych na poużytkowych foliach z poli(tereftalanu etylenu) oraz poli(tlenku tetrametylenu)
Autorzy:
Paszkiewicz, S.
Szymczyk, A.
Irska, I.
Pawlikowska, D.
Piesowicz, E.
Powiązania:
https://bibliotekanauki.pl/articles/947294.pdf
Data publikacji:
2018
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Chemii Przemysłowej
Tematy:
reactive blend
post-consumer glycol-modified poly(ethylene terephthalate) foil
glass transition temperature
thermal stability
mieszanina reaktywna
poużytkowa folia z poli(tereftalanu etylenu) modyfikowanego glikolem
temperatura zeszklenia
stabilność termiczna
Opis:
Two series of reactive polymer blends based on post-consumer glycol-modified poly(ethylene terephthalate) (PETG) and poly(tetramethylene oxide) (PTMO) were prepared in order to investigate the possibility of utilization of waste PETG foils from the packaging industry. The resulting copolymer consisted of hard segments based on PETG and soft segments of PTMO, the latter accounted for 25, 35 or 50 percent of the total mass. The effects of the content and length of the soft segments derived from poly(oxybutylene) glycol, with molecular weights of 1000 or 2000, on the structure and thermal properties of the resulting materials were investigated.
Przygotowano dwie serie reaktywnych mieszanin polimerowych na bazie poużytkowej folii z poli(tereftalanu etylenu) modyfikowanego glikolem (PETG) oraz poli(tlenku tetrametylenu) (PTMO) w celu zbadania możliwości zagospodarowania odpadowych folii PETG z przemysłu opakowaniowego. PETG stanowił w kopolimerze segmenty sztywne, a PTMO segmenty giętkie, których udział wynosił 25, 35 lub 50 % mas. Zbadano wpływ udziału segmentów giętkich oraz długości ich łańcuchów, pochodzących z glikolu polioksybutylenowego o masie molowej odpowiednio 1000 g/mol lub 2000 g/mol, na strukturę oraz właściwości termiczne otrzymanych materiałów.
Źródło:
Polimery; 2018, 63, 1; 45-48
0032-2725
Pojawia się w:
Polimery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena zdolności tworzenia biofilmu P. Aeruginosa na próbkach stopu AZ31 uzyskanego w technologii SLM
Ability of clinical P. Aeruginosa strains to form biofilm on the SLM-produced AZ31 specimens
Autorzy:
Pawlak, A.
Szymczyk, P.
Chlebus, E.
Junka, A.
Secewicz, A.
Powiązania:
https://bibliotekanauki.pl/articles/99015.pdf
Data publikacji:
2015
Wydawca:
Politechnika Śląska. Katedra Biomechatroniki
Tematy:
selective laser melting
AZ31
P.aeruginosa
technologie przyrostowe
Opis:
W pracy przedstawiono wyniki badań nad oceną zdolności tworzenia biofilmu szczepu bakterii P. Aeruginosa, na powierzchni próbek wyprodukowanych z lekkiego stopu magnezu - AZ31 w technologii SLM. Ilość kolonii bakteryjnych wyhodowanych w biofilnie, jest nawet 700x wyższa, w odniesieniu do skafoldów ze stopu Ti-6Al-7Nb, wyprodukowanych w tej samej technologii.
In this work, results of research on ability to form biofilm by P. Aeruginosa strains on AZ31 specimens manufactured in SLM technology are reported. The number of cells forming biofilm on specimens is even 700 times higher than on scaffolds manufactured from Ti-6Al-7Nb alloy by SLM technique.
Źródło:
Aktualne Problemy Biomechaniki; 2015, 9; 89-92
1898-763X
Pojawia się w:
Aktualne Problemy Biomechaniki
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ion Implantation and Transient Melting: A New Approach to Formation of Superconducting MgB$\text{}_{2}$ Phases
Autorzy:
Piekoszewski, J.
Kempiński, W.
Stankowski, J.
Prokert, F.
Richter, E.
Stanisławski, J.
Werner, Z.
Szymczyk, W.
Powiązania:
https://bibliotekanauki.pl/articles/2041609.pdf
Data publikacji:
2004-12
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
74.70.-b
74.78.-w
Opis:
An attempt to synthesize superconducting MgB$\text{}_{2}$ inter-metallic compound from the liquid state is presented. The process consists of two steps. In the first one, boron ions are implanted into a magnesium substrate. In the second one, the near-surface region of such system is melted by short, intense hydrogen plasma pulses without necessity of annealing in Mg vapor. A magnetically modulated microwave absorption method was used to detect superconducting regions in the obtained MgB$\text{}_{2}$ layer. Percolation between nano-regions (islands) of MgB$\text{}_{2}$ has not been observed. However, a superconducting state of the insulated islands has been experimentally proven with transition temperatures T$\text{}_{C}$ as high as 31 K.
Źródło:
Acta Physica Polonica A; 2004, 106, 6; 861-868
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies