Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Lee, B." wg kryterium: Autor


Tytuł:
Performance analysis of doppler aided GPS/QZSS precise positioning for land vehicles
Autorzy:
Lee, B. H.
Jee, G. I.
Powiązania:
https://bibliotekanauki.pl/articles/320665.pdf
Data publikacji:
2013
Wydawca:
Polskie Forum Nawigacyjne
Tematy:
QZSS
land navigation
intelligent transport systems
Opis:
For ITS (Intelligent Transport Systems), especially for land vehicles, precise position is the prime information. GNSS is the most popular navigation system. Generally, ITS demands lane distinguishable positioning accuracy. However urban area is most environments of land vehicles and the signal blocks of satellite with low elevation angle, multipath error and etc. make unreliable positioning results. Especially, lack of number of visible satellites (fewer than 4 satellites) cannot provide positioning results. QZSS (Quasi-Zenith Satellite System) which operated by Japan has high interoperability. In addition, its elevation angle is very high in long time in Korea. It means QZSS signal can be received in urban area and it can be great advantage for land vehicles. The most positioning errors are occurred by multipath, cycle slip, and etc. For example, multipath error is unexpected momentary error. In order to reduce position error, smoothing technique in position domain is needed. In this paper, precise positioning for land vehicles was evaluated. First, by using QZSS, probability of navigation solution was enhanced. Second, the reliability is improved by smoothing positioning result using Doppler measurement. The analysis was performed by trajectory analysis using precise map data.
Dla inteligentnych systemów transportowych, zwłaszcza w odniesieniu do pojazdów lądowych, dokładna informacja o pozycji jest pierwszorzędna. Systemy satelitarne (GNSS) to obecnie najbardziej popularne systemy nawigacyjne. Zasadniczo inteligentne systemy transportowe wymagają znajomości pozycji determinowanej warunkami drogowymi, a obszary miejskie stanowią środowisko, w którym porusza się największa liczba pojazdów lądowych. Takie ograniczenia, jak przesłanianie niskich satelitów, błąd wielodrożności i tym podobne powodują, że pozycje wyznaczane metodami satelitarnymi stają się mało wiarygodne. Brak wyznaczeń może być spowodowany zwłaszcza brakiem dostatecznej liczby widocznych satelitów (mniej niż cztery). QZSS (Quasi-Zenitalny System Satelitarny), uruchomiony w Japonii, cechuje się w tym względzie niezwykle korzystnymi cechami. W dodatku jego wysokość topocentryczna przez długi czas jest bardzo duża dla obserwatora znajdującego się w Korei. Oznacza to, że sygnał tego systemu może być odbierany w obszarze miejskim, co stanowi bardzo korzystną cechę dla pojazdów lądowych. Większość błędów pozycji wynika w tym wypadku z błędu wielodrogowości, przeskoków fazy i tym podobnych. Na przykład, wielodrogowość obrazuje się jako chwilowe, niespodziewane odchylenie pozycji. Dla zmniejszenia tego rodzaju błędów niezbędna jest technika wygładzania pozycji. W artykule ocenie poddano dokładność pozycjonowania pojazdów lądowych. Po pierwsze poprzez zastosowanie QZSS poprawiono prawdopodobieństwo poprawnego rozwiązania, po drugie poprzez zastosowanie technik wygładzania z użyciem pomiarów dopplerowskich poprawiono wiarygodność wyznaczeń. Analizy wyników dokonano przez analizę trajektorii, odnosząc ją do dokładnych danych mapy.
Źródło:
Annual of Navigation; 2013, 20; 85-96
1640-8632
Pojawia się w:
Annual of Navigation
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Jankesi na Okinawie : obrońcy czy chuligani
Autorzy:
Beals, Gregory.
Lee, B. J.
Takayama, Hideko.
Hirsh, Michael.
Vistica, Gregory.
Powiązania:
Forum 2000, nr 32, s. 12-13
Współwytwórcy:
(jr). Tłumaczenie
Data publikacji:
2000
Tematy:
Stacjonowanie wojsk poza granicami państwa Stany Zjednoczone
Bezpieczeństwo międzynarodowe Azja
Polityka międzynarodowa
Polityka zagraniczna
Opis:
Tł. art. zamieszcz. w "Newsweek". --- 2000, 24 VII.
Dostawca treści:
Bibliografia CBW
Artykuł
Tytuł:
Atomistic Analysis Of Radiation-Induced Segregation In Ion-Irradiated Stainless Steel 316
Analiza w skali atomowej indukowanej promieniowaniem segregacji w stali nierdzewnej 316
Autorzy:
Lee, G.-G.
Jin, H.-H.
Chang, K.
Lee, B. H.
Kwon, J.
Powiązania:
https://bibliotekanauki.pl/articles/354713.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
atom probe tomography (APT)
radiation-induced segregation (RIS)
ion irradiation
irradiation defects
stainless steel
APT
RIS
stal nierdzewna
segregacja
Opis:
Stainless steel (SS) is a well-known material for the internal parts of nuclear power plants. It is known that these alloys exhibit radiation-induced segregation (RIS) at point defect sinks at moderate temperature, while in service. The RIS behavior of SS can be a potential problem by increasing the susceptibility to irradiation-assisted stress corrosion cracking. In this work, the RIS behavior of solute atoms at sinks in SS 316 irradiated with Fe4+ ions were characterized by atom probe tomography (APT). There were torus-shaped defects along with a depletion of Cr and enrichment of Ni and Si. These clusters are believed to be dislocation loops resulting from irradiation. The segregation of solutes was also observed for various defect shapes. These observations are consistent with other APT results from the literature. The composition of the clusters was analyzed quantitatively almost at the atomic scale. Despite the limitations of the experiments, the APT analysis was well suited for discovering the structure of irradiation defects and performing a quantitative analysis of RIS in irradiated specimens.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1179-1184
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure Development of Spark Plasma Sintered Ti-Nb Alloy by Heat Treatment
Autorzy:
Haq, M. A.
Abbas, S. F.
Eom, N. S. A.
Kim, T. S.
Lee, B.
Park, K.-T.
Kim, B. S.
Powiązania:
https://bibliotekanauki.pl/articles/355593.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
TiNb alloy
Spark plasma sintering
Heat treatment
Microstructure
β-phase titanium
Opis:
The β-phase Titanium (β-Ti) alloys have been under the spotlight in the recent past for their use as biomedical prosthetic materials owing to their excellent properties such as low elastic modulus, high corrosion resistance and tensile strength. Recently, Niobium (Nb) has gained a lot of attention as a β-phase stabilizing element in Ti alloys to replace Vanadium (V) due to its excellent solubility in Ti, low elastic modulus and biocompatibility. In this work, low cost Ti-20Nb binary alloy has been fabricated via powder metallurgy procedures. The blended powder mixtures of Ti and Nb were sintered at 900°C for 20 mins by the Spark Plasma Sintering (SPS) with an applied uniaxial pressure of 40 MPa. The heating rate was fixed at 50°C/min. The sintered alloy was subject to heat treatments at 1200°C in vacuum condition for various time durations. The characterizations of microstructure obtained during this process were done using FE-SEM, EDS and XRD. By increasing heat treatment time, as understood, the volume of residual Nb particles was decreased resulting in accelerated diffusion of Nb into Ti. Micro hardness of the alloy increased from 340 to 355 HV with the increase in β phase content from 30 to 45%. The resultant alloys had relatively high densities and homogenized microstructures of dispersed lamellar β grains in α matrix.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1429-1432
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication and Characterization of CoCrFeNiMn High Entropy Alloy Powder Processed by Gas Atomization
Autorzy:
Park, T. G.
Lee, S. H.
Lee, B.
Cho, H. M.
Choi, W. J.
Kim, B. S.
Shin, K. S.
Kim, T.-S.
Powiązania:
https://bibliotekanauki.pl/articles/353649.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high entropy alloy
gas atomization
spark plasma sintering
CoCrFeNiMn
Opis:
In this study, precisely controlled large scale gas atomization process was applied to produce spherical and uniform shaped high entropy alloy powder. The gas atomization process was carried out to fabricate CoCrFeNiMn alloy, which was studied for high ductility and mechanical properties at low temperatures. It was confirmed that the mass scale, single phase, equiatomic, and high purity spherical high entropy alloy powder was produced by gas atomization process. The powder was sintered by spark plasma sintering process with various sintering conditions, and mechanical properties were characterized. Through this research, we have developed a mass production process of high quality and spherical high entropy alloy powder, and it is expected to expand applications of this high entropy alloy into fields such as powder injection molding and 3D printing for complex shaped components.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1055-1059
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Multistep Heat-Treatment Effects on Electrospun Nd-Fe-B-O Nanofibers
Autorzy:
Jeon, E. J.
Eom, N. S. A.
Lee, J.
Lee, B.
Cho, H. M.
On, J. S.
Choa, Y.-H
Kim, B. S.
Powiązania:
https://bibliotekanauki.pl/articles/354311.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Nd-Fe-B
nanofibers
electrospinning
heat treatment
Opis:
Neodymium-Iron-Boron (Nd-Fe-B) magnets are considered to have the highest energy density, and their applications include electric motors, generators, hard disc drives, and MRI. It is well known that a fiber structure with a high aspect ratio and the large specific surface area has the potential to overcome the limitations, such as inhomogeneous structures and the difficulty in alignment of easy axis, associated with such magnets obtained by conventional methods. I n this work, a suitable heat-treatment procedure based on single-step and multistep treatments to synthesize sound electrospun Nd-Fe-B-O nanofibers of Φ572 nm was investigated. The single-step heat-treated (directly heat-treated at 800°C for 2 h in air) samples disintegrated along with the residual organic compounds, whereas the multistep heat-treated (sequential three-step heat-treated including three steps;: dehydration (250°C for 30 min in an inert atmosphere), debinding (650°C for 30 min in air), and calcination (800°C for 1 h in air)) fibers maintained sound fibrous morphology without any organic impurities. They could maintain such fibrous morphologies during the dehydration and debinding steps because of the relatively low internal pressures of water vapor and polymer, respectively. In addition, the NdFeO3 alloying phase was dominant in the multistep heat-treated fibers due to the removal of barriers to mass transfer in the interparticles.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1433-1437
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Warm Tensile Deformation Behavior and Constitutive Equation of Supersaturated Solid-Solutionized Al-9Mg Extruded Alloy
Autorzy:
Yang, Seung Y.
Kim, Bong H.
Lee, Da B.
Choi, Kweon H.
Kim, Nam S.
Ha, Seong H.
Yoon, Young O.
Lim, Hyun K.
Kim, Shae
Kim, Young J.
Powiązania:
https://bibliotekanauki.pl/articles/2048882.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminum alloy
Al-9Mg alloy
tensile test
constitutive equation
Opis:
In this paper, as a purpose to apply the supersaturated solid-solutionized Al-9Mg alloy to the structural sheet parts of automotive, tensile tests were conducted under the various conditions and a constitutive equation was derived from the tensile test results. Al-9Mg alloy was produced using a special Mg master alloy containing Al2Ca during the casting process and extruded into the sheet. In order to study the deformation behavior of Al-9Mg alloy in warm temperature forming environments, tensile tests were conducted under the temperature of 373 K-573 K and the strain rate of 0.001/s~0.1/s. in addition, by using the raw data obtained from tensile tests, a constitutive equation of the Al-9Mg alloy was derived for predicting the optimized condition of the hot stamping process. Al-9Mg alloy showed uncommon deformation behavior at the 373 K and 473 K temperature conditions. The calculated curves from the constitutive equation well-matched with the measured curves from the experiments particularly under the low temperature and high strain rate conditions.
Źródło:
Archives of Metallurgy and Materials; 2021, 66, 4; 1013-1018
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and Mechanical Properties of Hot-deformed AlMg4 Alloys with the Variations of Mn, Fe, and Si Contents
Autorzy:
Lee, Da B.
Kim, Bong H.
Choi, Kweon H.
Yang, Seung Y.
Kim, Nam S.
Ha, Seong H.
Yoon, Young O.
Lim, Hyun K.
Kim, Shae
Hyun, Soong K..
Powiązania:
https://bibliotekanauki.pl/articles/351603.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Al-Mg alloy
intermetallic compounds
homogenization
hot-rolling
microstructure
Opis:
This paper aims to investigate the microstructural evolution and mechanical properties of hot-deformed AlMg4 alloys with Mn, Fe, and Si as the main impurities. For this purpose, solidification behavior and microstructural evolution during hot-rolling and heat-treatment processes are investigated by using theoretical calculations and experimental characterization. The crystallization and morphological transformation of intermetallic Al3 Fe, Al6 Mn, and Mg2 Si phases are revealed and discussed in terms of the variation in chemical composition. Following a homogenization heat-treatment, the effect of heat treatment on the intermetallic compounds is also investigated after hot-rolling. It was revealed that the Mg2 Si phase can be broken into small particles and spherodized more easily than the Al3 Fe intermetallic phase during the hot-rolling process. For the Mn containing alloys, both yield and ultimate tensile strength of the hot-rolled alloys increased from 270 to 296 MPa while elongation decreased from 17 to 13%, which can be attributed to Mn-containing intermetallic as well as dispersoid.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 4; 1255-1259
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Valorization of Cobalt from Waste LIB Cathode through Cobalt Oxalate and Cobalt Oxide Synthesis by Leaching-Solvent Extract-Precipitation Stripping
Autorzy:
Swain, B.
Lee, J.-C.
Lee, C.-G.
Powiązania:
https://bibliotekanauki.pl/articles/352333.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
valorization of cobalt
cobalt oxide powder
rod-shaped cobalt oxalate
precipitation stripping
Opis:
An ecoefficient, economical and sustainable valorization process for the synthesis of Co3O4 from waste lithium-ion battery (LIB) by leaching-solvent extract-scrubbing-precipitation stripping route has been developed. Through an optimization, the waste LIB cathode was leached using 2000 mole/m3 of H2SO4 and 5 Vol. % of the H2O2 at a pulp density of 100 kg/m3 under leaching time 60 minutes and temperature 75°C. From the separated leach liquor, cobalt was purified by saponified Cyanex 272. From cobalt, loaded Cyanex 272 impurities were scrubbed and the CoC2O4·2H2O was recovered through precipitation stripping. Finally, the precipitate was calcined to synthesize Co3O4, which is a precursor for LIB cathode materials manufacturing. From TGA-DTA, followed by XRD analysis it was confirmed that at 200°C the CoC2O4·2H2O can be converted to anhydrous CoC2O4 and at 350°C the anhydrous can be converted to Co3O4 and at 1100°C the Co3O4 can be converted to CoO. Through reported route waste LIB can back to LIB manufacturing process through a versatile and flexible industrial approach.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1037-1042
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics Of The Porous Body Sintered By Nano-Sized Fe-Cr-Al Alloy Powder
Charakterystyka porowatego korpusu spiekanego z nanometrycznego proszku stopu Fe-Cr-Al
Autorzy:
Lee, S.-I.
Lee, S.-H.
Gu, B.-U.
Lee, D.-W.
Kim, B.-K.
Powiązania:
https://bibliotekanauki.pl/articles/356635.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Fe-Cr-Al powder
metallic sponges
sintering temperature
oxidation resistance
proszek Fe-Cr-Al
proszek nanometryczny
temperatura spiekania
odporność na utlenianie
Opis:
Porous metal with uniform honeycomb structure was successfully produced by sintering using Fe-Cr-Al nano powder, which was prepared by the pulsed wire evaporation (PWE) in ethanol. Its process consisted of the several steps; 1) coating on the surface of polyurethane sponge with the liquid droplets generated from the ethanol-based slurry where the Fe-Cr-Al nano powders were uniformly dispersed, 2) heat treatment of debinding to remove the polyurethane sponge and 3) sintering of the porous green body formed by Fe-Cr-Al nano powders. The strut thickness of porous Fe-Cr-Al was increased by the increase of spraying times in ESP step. Also, The shrinkages and the oxidation resistance of the sintered porous body was increased with increase of sintering temperature. The optimal sintering temperature was shown to 1450°C in views to maximize the oxidation resistance and sinterability.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1275-1279
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect Of Compaction Pressure And Sintering Temperature On The Liquid Phase Sintering Behavior Of Al-Cu-Zn Alloy
Wpływ ciśnienia prasowania i temperatury spiekania na spiekanie stopu Al-Cu-Zn z udziałem fazy ciekłej
Autorzy:
Lee, S. H.
Ahn, B.
Powiązania:
https://bibliotekanauki.pl/articles/351836.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
powder metallurgy
liquid phase sintering
compaction pressure
Al-Cu-Zn alloy
metalurgia proszków
spiekanie w fazie ciekłej
ciśnienie prasowania
stop Al-Cu-Zn
Opis:
The liquid phase sintering characteristics of Al-Cu-Zn alloy were investigated with respect to various powder metallurgy processing conditions. Powders of each alloying elements were blended to form Al-6Cu-5Zn composition and compacted with pressures of 200, 400, and 600 MPa. The sintering process was performed at various temperatures of 410, 560, and 615°C in N2 gas atmosphere. Density and micro-Vickers hardness measurements were conducted at different processing stages, and transverse rupture strength of sintered materials was examined for each condition, respectively. The microstructure was characterized using optical microscope and scanning electron microscopy. The effect of Zn addition on the liquid phase sintering behavior during P/M process of the Al-Cu-Zn alloy was also discussed in detail.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1485-1489
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Preparation of Submicroscale Ag-Coated Cu Particles by Multi-Step Addition of Ag Plating Solution and Antioxidation Properties for Different Ag Shell Thicknesses
Autorzy:
Choi, E. B.
Lee, J.-H.
Powiązania:
https://bibliotekanauki.pl/articles/351202.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ag-coated Cu particle
submicrometer
Glycol-based Ag plating solution
mult-step addition
antioxidation
Opis:
For application as a low-cost conductive filler material, submicroscale Cu@Ag particles were fabricated at room temperature without any reductants by a multi-step addition method using an ethylene glycol-based Ag plating solution. Scanning electron microscopy images of the Ag-coated Cu particles demonstrated the formation of discrete Ag particles less than 100 nm in size as well as a thin Ag coating on Cu particles, during the early addition steps. However, as the thickness of the Ag coating increased, the small Ag particles agglomerated into Ag coatings with an increase in the number of Ag plating steps. Owing to the absence of additives such as surfactants, a comparison between the microstructural images and calculations indicated increased agglomeration between fabricated Ag-coated Cu particles with an increase in the number of Ag plating steps. However, thermogravimetric-differential scanning calorimetry of the agglomerated Ag-coated Cu particles after the fifth addition of the Ag plating solution demonstrated their antioxidation behavior even after 70 min in air at 150°C.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1137-1142
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Design of simultaneous input-shaping-based SIRMs fuzzy control for double-pendulum-type overhead cranes
Autorzy:
Qian, D.
Tong, S.
Yang, B.
Lee, S.
Powiązania:
https://bibliotekanauki.pl/articles/953059.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
SIRMs fuzzy control
double-pendulum-type overhead cranes
sterowanie rozmyte
SIRM
suwnica wahadłowa
Opis:
Overhead cranes are extensively employed but their performance suffers from the natural sway of payloads. Sometime, the sway exhibits double-pendulum motions. To suppress the motions, this paper investigates the design of simultaneous input-shaping-based fuzzy control for double-pendulum-type overhead cranes. The fuzzy control method is based on the single input-rule modules (SIRMs). Provided the all the system variables are measurable, the SIRMs fuzzy controller is designed at first. To improve the performance of the fuzzy controller, the simultaneous input shaper is adopted to shape the control command generated by the fuzzy controller. Compared with other two control methods, i.e., the SIRMs fuzzy control and the convolved input-shaping-based SIRMs fuzzy control, simulation results illustrate the feasibility, validity and robustness of the presented control method for the anti-swing control problem of double-pendulum-type overhead cranes.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2015, 63, 4; 887-896
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Strut Thickness on Room and High Temperature Compressive Properties of Block-Type Ni-Cr-Al Powder Porous Metals
Autorzy:
Kang, B.-H.
Park, M.-H.
Lee, K.-A.
Powiązania:
https://bibliotekanauki.pl/articles/355591.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ni-Cr-Al
powder porous metal
strut thickness
high temperature
compressive behavior
Opis:
This study investigated the effect of strut thickness on the room and high temperature compressive properties of block-type Ni-Cr-Al powder porous metals with ~3000 μm pore size manufactured using a new powder process. Two block-type Ni-Cr-Al porous metals with different strut thicknesses were manufactured. The strut thicknesses of two block foams were 340 μm (A) and 383 μm (B), respectively. Room temperature, 500°C, 650°C and 800°C compressive tests were performed. The compressive results identified typical elastic, plateau and densification regions of foam material in all temperature conditions. Regardless of the strut thickness, compressive strength (maximum peak stress) decreased as deformation temperature increased. In all deformation temperature ranges, the compressive strength measured higher in the porous metal with greater strut thickness (B). The high temperature deformation behavior of powder porous metal was confirmed to be affected by the structural factor and microstructural factor of the porous metal. With the findings described above, this study also discussed the high temperature deformation mechanism of the Ni-Cr-Al metal foam based on fracture surfaces after the high temperature compressions.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1329-1334
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies