Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "fuel-water microemulsion" wg kryterium: Wszystkie pola


Wyświetlanie 1-7 z 7
Tytuł:
Selected physicochemical properties of water-fuel microemulsion as an alternative fuel for diesel engine
Autorzy:
Górska, Milena
Bukrejewski, Paweł
Stobiecki, Jerzy
Powiązania:
https://bibliotekanauki.pl/articles/262891.pdf
Data publikacji:
2019
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
microemulsion
alternative fuel
diesel engine
environmental protection
Opis:
The paper focuses on the assessment of selected physicochemical properties of microemulsion containing 5% by mass (m/m) of surface active compounds (SAC), i.e. Span20 and Crilet4 as well as 10% (m/m) of distilled water dispersed in diesel fuel (DF). In particular temperature dependent properties such as: flash point (FP) and cold filter plugging point (CFPP) as well as lubricity, friction coefficient, corrosiveness and kinematic viscosity of tested fuels were examined. It was found that the tested surfactants and water added to DF increase microemulsion FP by 13ºC. For this reason, it can be stated that tested microemulsion is safer than typical DF. On the other hand it was found that the CFPP of the tested microemulsion is also adequately higher. It means less usefulness of such fuel during winter periods. Based on the research results it can be stated that addition of tested surfactants slightly worsens the lubricity of DF. However, the same surfactants in the presence of dispersed water reduce the friction in the tribological node and improve the lubricity of the tested microemulsion. Research showed that tested microemulsion system is not corrosive as well as its kinematic viscosity meet requirements of EN590 standard. Based on all these findings, microemulsion is considered as safe and such fuel can be recommended for engine tests without the risk of its damage.
Źródło:
Archiwum Motoryzacji; 2019, 84, 2; 45-56
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Researches of a combustion engine fuelled with a fuel-water microemulsion
Autorzy:
Kowalski, M.
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/244980.pdf
Data publikacji:
2018
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
combustion processes
ecology
fuel-water microemulsion
Opis:
The emulsion is a mixture of two or more insoluble liquids. Microemulsion is the emulsion with particles dimension in a range of one micrometre and smaller. Such a microemulsion of water and diesel fuel will create a novel quality and allows one to simultaneously achieve environmental and economic effects, as well as eliminate the ad-verse impact of normal emulsions, or adverse effects of water injection into the engine intake system or directly into the combustion chamber, as well as the sequential injection of water directly into the combustion chamber. Application of microemulsion of water and diesel to fuel diesel engine positively affects the combustion process through the catalytic impact of microparticles of water, and improves the process of preparation of the microemulsion injection into the combustion chamber as a result of water microparticles’ microexplosions. This article presents the investigation results of an internal combustion engine fuelled by an emulsion of water and diesel fuel and fuelled by emulsion of FAME and water. It therefore seems appropriate to a strong increase in the degree of dispersion of water droplets in the emulsion by applying the methods to obtain the size of water droplets on nanometric range. This should dramatically improve both the stability of emulsion and its influence on the chemical effects of combustion in diesel engine.
Źródło:
Journal of KONES; 2018, 25, 4; 187-196
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania wybranych właściwości fizykochemicznych mikroemulsji wodno-paliwowej
Research of the selected physicochemical properties of the water in diesel oil microemulsion
Autorzy:
Górski, K.
Czerwonka, D.
Bocho-Janiszewska, A.
Wasilewski, T.
Longwic, R.
Powiązania:
https://bibliotekanauki.pl/articles/310232.pdf
Data publikacji:
2017
Wydawca:
Instytut Naukowo-Wydawniczy "SPATIUM"
Tematy:
silnik o zapłonie samoczynnym
olej napędowy
mikroemulsja paliwowa
diesel engine
diesel oil
fuel microemulsion
Opis:
W artykuleopisano wyniki badań wybranych właściwości fizykochemicznych mikroemulsji wodno–paliwowych, które można zastosować do zasilania silników o zapłonie samoczynnym. Badania dotyczyły oleju napędowego, do którego wprowadzono odpowiednie surfaktanty oraz wodę w ilości 4 i 8% wagowo (m/m). W celu uzyskania mikroemulsji zastosowano dwa rodzaje niejonowych związków powierzchniowo czynnych tj. alkohol laurylowy oksyetylenowany 3 molami tlenku etylenu (Laureth – 3) oraz alkohol laurylowy oksyetylenowany 7 molami tlenku etylenu (Laureth – 7). Wprowadzenie tych związków chemicznych oraz wody do oleju napędowego pozwoliło uzyskać mikroemulsje paliwowe, które w niniejszej pracy oznaczono kodem L4 i L8. Średnica cząstek fazy rozproszonej w oleju napędowym zawiera się w zakresie 4–100 nm. Z tego powodu obydwie badane mikroemulsje są transparentne i stabilne termodynamicznie. Ich gęstość jest nieznacznie większa (o ok. 1%) w stosunku do oleju napędowego. Zauważono wyraźny wpływ wody oraz zastosowanych surfaktantów na wzrost lepkości mikroemulsji oraz jej temperatury zapłonu w stosunku do oleju napędowego. Jednocześnie badane mikroemulsje charakteryzowały się mniej korzystnymi właściwościami niskotemperaturowymi, co może utrudnić ich zastosowanie w warunkach zimowych.
Paper presents research results of selected physicochemical properties of water – fuel microemulsion, which can be used as a fuel for a diesel engines. Researches were carried out for a diesel oil blended with selected surfactants and water at 4 and 8 % by weight. Tested microemulsions contained a two kinds of nonionic surfactants, ie., lauryl alcohol ethoxylates with 3 moles of ethylene oxide (Laureth - 3) and a lauryl alcohol ethoxylates with 7 moles of ethylene oxide (Laureth - 7). The addition of these chemicals and water to the diesel oil allows to formulate a fuel microemulsions marked by a code L4 and L8. The particle diameter of the dispersed phase in the diesel oil is in the range of 4-100 nm. For this reason, both tested microemulsions are thermodynamically stable and transparent. Their density is slightly greater (approx. 1%) compared to diesel oil. It was observed an impact of water and surfactants on increasing the microemulsions viscosity and the ignition temperature compared to diesel oil. At the same time the low temperature properties of tested microemulsions wereless favorable, which may hinder their use in winter conditions.
Źródło:
Autobusy : technika, eksploatacja, systemy transportowe; 2017, 18, 6; 705-709, CD
1509-5878
2450-7725
Pojawia się w:
Autobusy : technika, eksploatacja, systemy transportowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Emisja spalin silnika o zapłonie samoczynnym zasilanego mikroemulsją wodno-paliwową
Exhaust gases emission of the diesel engine fuelled with water-fuel microemulsion
Autorzy:
Górski, K.
Czerwonka, D.
Bocho-Janiszewska, A.
Wasilewski, T.
Lotko, W.
Longwic, R.
Hernik, A.
Powiązania:
https://bibliotekanauki.pl/articles/316026.pdf
Data publikacji:
2017
Wydawca:
Instytut Naukowo-Wydawniczy "SPATIUM"
Tematy:
silnik o zapłonie samoczynnym
olej napędowy
mikroemulsja paliwowa
emisja spalin
diesel engine
diesel oil
fuel microemulsion
exhaust emission
Opis:
W artykule przedstawiono wyniki badań dotyczące oceny emisji wybranych składników spalin z silnika AD3.152 zasilanego mikroemulsją wodno – paliwową. Badania przeprowadzono dla oleju oraz mikroemulsji woda – olej napędowy, zawierającej 4 i 8 % (m/m) wody. Testy silnikowe wykonano w warunkach ustalonych dla średnich obciążeń silnika tj. 80, 100 i 120 Nm i prędkości wału korbowego 1600 obr/min. Uzyskane wyniki wskazują, że dla przyjętych warunków testu nie stwierdzono istotnego wpływu wody zawartej w mikroemulsji paliwowej na zmianę stężenia badanych składników spalin silnika.
Paper presents research results of selected exhaust gases from the AD3.152 diesel engine fuelled with water-diesel oil microemulsion. Tests were carried out for a diesel oil as well as for its microemulsion containing 4 and 8 % of water by weight. Engine research were done for a stationary condition at a middle load of 80, 100 and 120 Nm and for the crankshaft rotational speed of 1600 rpm. Results of these preliminary research suggest that content of water in tested microemulsions has not of any significant impact on emissions from tested engine.
Źródło:
Autobusy : technika, eksploatacja, systemy transportowe; 2017, 18, 6; 710-713, CD
1509-5878
2450-7725
Pojawia się w:
Autobusy : technika, eksploatacja, systemy transportowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ mikroemulsji wodno-paliwowej na opóźnienie samozapłonu w silniku o zapłonie samoczynnym
Impact of the water-fuel microemulsion on the self-ignition delay in a diesel engine
Autorzy:
Górski, K.
Wasilewski, T.
Czerwonka, D.
Bocho-Janiszewska, A.
Longwic, R.
Powiązania:
https://bibliotekanauki.pl/articles/310265.pdf
Data publikacji:
2017
Wydawca:
Instytut Naukowo-Wydawniczy "SPATIUM"
Tematy:
silnik o zapłonie samoczynnym
mikroemulsja paliwowa
olej napędowy
diesel engine
diesel oil
fuel microemulsion
Opis:
W artykule przedstawiono wyniki badań z zakresu oceny wpływu składu mikroemulsji wodno-paliwowej na opóźnienie jej samozapłonu w silniku o zapłonie samoczynnym. W celu przygotowania mikroemulsji wykorzystano standardowy olej napędowy oraz surfaktanty/ko-surfaktanty na bazie alkoholu laurylowego. Do takiej mieszaniny wprowadzono wodę destylowaną w ilości 4 i 8 % (m/m). Uzyskane w ten sposób mikroemulsje L-4 i L-8 wykorzystano do przeprowadzenia badań silnikowych. Wyniki tych badań wskazują, że zastosowanie wody w testowanych paliwach mikroemulsyjnych nie spowodowało zwiększenia wartości kąta opóźnienia samozapłonu w stosunku do silnika zasilanego olejem napędowym.
Paper presents an impact of the water-fuel microemulsion composition on self-ignition delay angle in the diesel engine. Tested microemulsions were prepared by blending of regular diesel oil and surfactant/co-surfactant based on the lauryl alcohol. Then to the mixture a distilled water was added in ratio of 4 and 8 % by mass. These microemulsion fuels were used for the engine research. Their results indicate that the value of selfignition delay angle calculated for microemulsions is comparable or slightly lower when compare to the diesel oil.
Źródło:
Autobusy : technika, eksploatacja, systemy transportowe; 2017, 18, 6; 714-717, CD
1509-5878
2450-7725
Pojawia się w:
Autobusy : technika, eksploatacja, systemy transportowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Water - fuel microemulsions influence on fuel consumption and exhaust gas emissions
Autorzy:
Cienciała, M.
Haller, P.
Jankowski, A.
Kardasz, P.
Powiązania:
https://bibliotekanauki.pl/articles/244361.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
diesel engine
microemulsion
fuel consumption
emissions
Opis:
Combustion in a diesel engine is a complex physicochemical process, changing the time at which the events take place simultaneously heat and mass transfer and chemical reactions. The development of internal combustion engines goes towards meeting the increasingly stringent requirements for toxic exhaust emissions, reducing fuel consumption and therefore reduce carbon emissions and protect the Earth's natural resources. The problem to solve in modern combustion engines is the emission of NOx. One way to reduce the emission of toxic NOx combustion engine power is water-hydrocarbon emulsions [1]. Research combustion engines water-hydrocarbon emulsions has been its tradition. So far, attempts were carried out using an emulsion obtained by a chemical. Emulsions of oil and water can be obtained by adding various detergents to prevent delamination of the oil and water. In this article, we consider the possibility of applying a mixture of water and oil as an alternative fuel used to power internal combustion engines used in heavy road transport. This work is preliminary work, also having to check whether this is the future direction of the work. The measurements of emissions of exhaust gases and fuel consumption. After analysing the test results confirmed that the improvement of the economic and environmental performance of modern diesel engines, it can be achieved by supplying synthetic diesel or gas oil water emulsions. It was found that the use of emulsion leads to a reduction of fuel consumption and NOx emissions.
Źródło:
Journal of KONES; 2013, 20, 3; 111-116
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of chosen parameters of water fuel microemulsion on combustion processes, emission level of nitrogen oxides and fuel consumption of CI engine
Autorzy:
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/247478.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engines
combustion process
ecology
emulsion
microemulsions
Opis:
The microemulsion is the emulsion with dimension of molecules approx. micrometre and smaller. Such microemulsion of water and diesel oil creates new quality and lets on obtainment ecological and economic of effects, as well as eliminates the disadvantageous influence common emulsions, or unprofitable effects of the injection of water to inlet system of the engine, direct to combustion chambers, as well as the sequential injection of water direct to combustion chambers. The essence of apply of the microemulsion is also improve catalytic influence of small molecules of water on combustion process, what, beside decreasing temperature combustion gases, influences both emission level components of toxic combustion gases, as and the level of the specific fuel consumption. The paper presents different ways of microemulsion production, novel way of microemulsion production, which does not demand apply of mixers and suffers obtainment of microemulsion with the volumetric content of water in diesel oil do 40% under conditions of laboratory and stabile the microemulsion with content of water in diesel oil to 25%. Results of laboratory research involving basic parameters of the microemulsion and engine researches with measurements emission ingredients of toxic exhaust gases and fuel consumptions are presented involving basic parameters of the microemulsion and engine researches with measurements emission ingredients (NOx, soot, fuel consumption) of toxic exhaust gases and fuel consumptions are presented in the paper.
Źródło:
Journal of KONES; 2011, 18, 4; 593-600
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-7 z 7

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies