Temat: shot peening - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: The numerical fem model of the kinematics of the vibratory shot peening process
Autorzy:: Bławucki, S.
Zaleski, K.
Powiązania:: https://bibliotekanauki.pl/articles/102472.pdf
Data publikacji:: 2017
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:: vibratory shot peening
FEM
vibratory shot peening kinematics
efficiency of vibratory shot peening
Opis:: The paper presents the results of numerical calculations, with the finite element method in the ABAQUS program environment, of the vibratory shot peening process with loose peening elements. The behaviour of shot peening elements was analysed in the kinematic aspect. The impact of the initial deployment of vibratory shot peening elements on their behaviour during processing was investigated, including the displacement, velocity, acceleration and the number of collisions. The way of determining the effectiveness of the processing with the vibratory shot peening was illustrated.
Źródło:: Advances in Science and Technology. Research Journal; 2017, 11, 4; 260-269
2299-8624
Pojawia się w:: Advances in Science and Technology. Research Journal
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: Influence of Single-Stage and Duplex Shot Peening on Surface Roughness and Residual Stresses in Al Mg5 Mn1 Sc0,8 Zr0,4 Alloy
Autorzy:: Byczkowska, P.
Sawicki, J.
Januszewicz, B.
Stegliński, M.
Powiązania:: https://bibliotekanauki.pl/articles/353741.pdf
Data publikacji:: 2018
Wydawca:: Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:: shot peening
double shot peening
residual stresses
roughness
Opis:: Conventional shot peening (SP) is cheap surface treatment widely used to enhance fatigue life of mechanical components [3,4]. Basically, it is shooting small particles (shots) on the surface of the sample. However, the process itself is so complex that a lot of companies are not able to optimally employ it due to the amount of parameters that must be controlled all at the same time. The duplex process consists in two stages of shot-peening treatment. The first one consist of shot-peening with spherical cast steel shots or cut wire shots. During the second stage the samples processed in stage one were subject to shot-peening with glass beads. In this work, RSA-501 aluminium alloy was shot peened using shots of different material and diameter and tested using a measurement of residual stresses and surface roughness. Tests and studies conducted so far on RSA-501 aluminium alloy demonstrate that bombardment by a treatment medium in the form of glass beads or shots of various shapes and diameters induces permanent plastic deformation of the surface layer. The roughness achieved after the shot-peening process was determined for each treatment medium. The largest value of Ra parameter was achieved for cut wire shots and this result is consistent with the above-mentioned theoretical knowledge. This medium is the most aggressive one to the surface being treated primarily due to the sharp edges of shots. The duplex process was successful in obtaining higher values of compressive stresses in surface layer than values achievable in conventional single-stage shot peening process.
Źródło:: Archives of Metallurgy and Materials; 2018, 63, 1; 505-511
1733-3490
Pojawia się w:: Archives of Metallurgy and Materials
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Analysis of the impact of double shot peening on the value of roughness parameter and distribution of stresses in the RSA 501 alloy
Autorzy:: Byczkowska, P.
Sawicki, J.
Januszewicz, B.
Stegliński, M.
Powiązania:: https://bibliotekanauki.pl/articles/957816.pdf
Data publikacji:: 2017
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:: shot peening
double shot peening
surface treatment
residual stresses
roughness
Opis:: The bead blasting process is widespread in both the automotive and aerospace industry and is performed in order to improve the fatigue strength of various components. Bead blasting is a cold plastic forming process during which the surface of the material processed is hit by small, hard particles consisting of steel pellets, bearing balls or glass beads. It increases the hardness of the outer layer and establishes compression stresses inside it, which is why this processing is often used to improve fatigue strength. Contrary to other peening methods, bead blasting does not result in a reduction in the height of the processed surface’s unevenness in most cases. Shot peening changes the residual tensile stresses into residual compression stresses, thanks to which, the lifetime of the parts processed is extended and their carrying capacity is increased. The double shot peening process proposed by the authors consists in a two-stage bead blasting process. The first stage consists in blasting with round cast steel pellets, pellets cut from wire or cast iron pellets. During the second stage the same samples underwent glass bead blasting. The tests conducted on the RSA-501 aluminum alloy indicate that as a result of the processing medium’s impact in the form of glass beads or pellets of different diameter and shape, a permanent plastic deformation of the material surface occurs. On the basis of the obtained results it is possible to infer that the choice of parameters of both conventional shot peening and the double shot peening determine the impact thereof on the material’s mechanical properties. Thanks to the application of the double shot peening process there is a noticeable decrease in value of the Ra parameter, by about 40% on average. When analyzing the compressive stress results it is possible to state that after the first blasting process the value of stress was increasing when moving deeply into the sample from its surface, while after the glass bead blasting the value of compressive stress was significantly higher already near the surface. Double shot peening results in an increase in the value of compressive stresses by 40-50% when compared to conventional blasting.
Źródło:: Advances in Science and Technology. Research Journal; 2017, 11, 3; 1-9
2299-8624
Pojawia się w:: Advances in Science and Technology. Research Journal
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: Influence of Shot Peening on Abrasion Wear in Real Conditions of Ni-Cu-Ausferritic Ductile Iron
Autorzy:: Wieczorek, A. N.
Powiązania:: https://bibliotekanauki.pl/articles/350866.pdf
Data publikacji:: 2016
Wydawca:: Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:: ADI
shot peening
wear
abrasion
Opis:: The paper presents results of the wear tests of chain wheels made of austempered ductile iron with various content of residual austenite. The aim of this study was to demonstrate the impact of the dynamic surface treatment (shot peening) on wear properties of surface layers of the chain wheels tested that were subjected to the action of quartz abrasive. Apart from determining the value of the abrasive wear, examinations of the magnetic phase content in the microstructure were carried out and plots of hardness of the surface layer as a function of the distance from the surface and microstructure of the materials were prepared. Based on the results, the following was found: an increase in the abrasive wear and a reduction in the hardness of the surface layer of chain wheels subjected to shot peening, as well as reduction of susceptibility to negative action of the shot for cast irons with the structure of upper ausferrite.
Źródło:: Archives of Metallurgy and Materials; 2016, 61, 4; 1985-1990
1733-3490
Pojawia się w:: Archives of Metallurgy and Materials
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: Parameters selection of shot peening gears of carburized and hardened steel 21NiCrMo2
Autorzy:: Tchórz, T.
Śnieżek, L.
Grzelak, K.
Mierzyński, J.
Powiązania:: https://bibliotekanauki.pl/articles/245218.pdf
Data publikacji:: 2016
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: materials engineering
shot peening
vehicles
gears
Opis:: This article presents the methodology of shot peening gears’ parameters selection used in agricultural tractor transmission. The gears made of steel have been treated with 21NiCrMo2 thermal-chemical consisting of carburization to the depth of 0.8 mm and subsequently hardened. The hardness of the side teeth surface after hardening was 58 HRC. The same process of thermo chemical was used for flat samples with dimensions 120×12×5 mm. Prepared samples were divided into two series. First shot peening was treated with spherical pellet with a varied diameter from 0.4 mm to 2.5 mm. For second series samples additional treatment of shot peening was not carried out. Then micro-hardness, roughness and longitudinal and transverse residual stresses were measured. As a result of the studies, there were selected parameters of shot peening, exerting the greatest influence on favourable residual stresses distribution in the surface layer of material and an increase in microhardness. At the same time, particular attention was paid to the morphology of samples surfaces after shot peening. There were rejected the parameters of shot peening, which caused damage to the surface in the form of visible cracks and craters. Based on the analysis presented in this article there were selected shot peening parameters, which will be applied during the additional dynamic surface processing of gears, used in the tractor’s drive system.
Źródło:: Journal of KONES; 2016, 23, 2; 389-395
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 6.

Tytuł:: The effect of the conditions of shot peening the Inconel 718 nickel alloy on the geometrical structure of the surface
Autorzy:: Zaleski, K.
Skoczylas, A.
Brzozowska, M.
Powiązania:: https://bibliotekanauki.pl/articles/102751.pdf
Data publikacji:: 2017
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:: surface roughness
shot peening
Inconel 718
Opis:: This article presents the research results of roughness and topography of the surface of Inconel 718 nickel alloy after shot peening. The evaluation of stereometric properties of the surface layer of the examined material was performed based on the amplitude, height and Abbott-Firestone curve parameters. The shot peening was carried out on the impulse shot peening stand. The impact energy Ez, distance between the traces xs and the ball diameter dk were changed in the range: Ez = 60 ÷ 240 mJ, xs = 0,15 ÷ 0,5 mm, dk = 3,95 ÷ 12,45 mm. The T8000 RC 120-140 device of the Hommel-Etamic company, along with the software, was used for measuring the surface roughness and for determining the material bearing curve. As a result of the machining, the surface roughness was reduced and the selected functional parameters were improved.
Źródło:: Advances in Science and Technology. Research Journal; 2017, 11, 2; 205-211
2299-8624
Pojawia się w:: Advances in Science and Technology. Research Journal
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 7.

Tytuł:: Shot Peening of a Mg-Al-Zn-Mn Alloy Surface
Autorzy:: Kottfer, D.
Mrva, P.
Powiązania:: https://bibliotekanauki.pl/articles/403372.pdf
Data publikacji:: 2010
Wydawca:: Wojskowa Akademia Techniczna im. Jarosława Dąbrowskiego
Tematy:: materials technology
shot peening
functional surface
roughness
Opis:: The paper describes the influence of shot peening on Mg-Al-Zn-Mn alloy surface. There are estimates focusing on the roughness of the shot peened surfaces and size of the selected shot peened material - corund. Based on the results of measurements, the evaluation was oriented on the curve of roughness, functionality of surface roughness Ra and the necessary quantity of shot peening material qnR of estimated material depending on the grain size dz.
Źródło:: Problemy Mechatroniki : uzbrojenie, lotnictwo, inżynieria bezpieczeństwa; 2010, 1, 1 (1); 21-29
2081-5891
Pojawia się w:: Problemy Mechatroniki : uzbrojenie, lotnictwo, inżynieria bezpieczeństwa
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 8.

Tytuł:: Effect of vibration shot peening parameters upon shapes of bearing curves of alloy steel surface
Autorzy:: Zaleski, K.
Skoczylas, A.
Powiązania:: https://bibliotekanauki.pl/articles/102198.pdf
Data publikacji:: 2015
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:: vibration shot peening
bearing curve
surface roughness
Opis:: The article presents the results of studies on the effect of technological parameters of vibration shot peening upon the shape of bearing curves and the parameters of that curve. The topography of surface formed in result of vibration shot peening and pre-machining, which was grinding, were analyzed. The material used in the studies was alloy steel 30HGSA. The shot peening process was performed on an appliance equipped with a kinematic vibrator. Shot peening time t, vibrator oscillations (vibrations) frequency ν, as well as vibrator oscillations amplitude A were changed within: t = 1–15 min, ν = 17,5–35 Hz, A = 10,3–17,3 mm. For measuring surface roughness and determining the bearing curve the appliance T8000 RC120-400 by Hommel- Etamic was used together with the software. In result of the machining performed surface roughness decreased, and the parameters of bearing curve improved.
Źródło:: Advances in Science and Technology. Research Journal; 2015, 9, 25; 20-26
2299-8624
Pojawia się w:: Advances in Science and Technology. Research Journal
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 9.

Tytuł:: Evaluation of the effectiveness of the shot peening process for thin-walled parts based on the diameter of impressions produced by the impact of shot media
Autorzy:: Zaleski, K.
Bławucki, S.
Powiązania:: https://bibliotekanauki.pl/articles/103268.pdf
Data publikacji:: 2015
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:: shot peening
thin walled parts
metal treatment
Opis:: The paper presents the results of studies on the effectiveness of the shot peening process for thin-walled parts based on the diameter of impressions produced by the impact of shot media. It is also described the current applications of this treatment for the thin-walled parts. The authors described an innovative measuring device which was used in the research. The material used in the studies was non-alloy steel C45. The relationships between beads diameter and thickness of workpieces on diameter of impression were presented.
Źródło:: Advances in Science and Technology. Research Journal; 2015, 9, 26; 77-82
2299-8624
Pojawia się w:: Advances in Science and Technology. Research Journal
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 10.

Tytuł:: Effect of the Shot Peening on Surface Properties and Tribological Performance of Ti-6Al-4V Alloy Produced by Means of DMLS Technology
Autorzy:: Żebrowski, R.
Walczak, M.
Powiązania:: https://bibliotekanauki.pl/articles/351652.pdf
Data publikacji:: 2019
Wydawca:: Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:: additive manufacturing
shot peening
titanium alloys
wear
tribology
Opis:: The purpose of the present paper was to investigate the effect of shot peening on the condition of the surface layer and abrasion resistance of specimens made of Ti-6Al-4V titanium alloy produced by Direct Metal Laser Sintering (DMLS) process. The specimens have been produced by means of EOSINT M280 system dedicated for laser sintering of metal powders and their surfaces have been subjected to the shot peening process under three different working pressures (0.2, 0.3 and 0.4 MPa) and by means of three different media i.e. CrNi steel shot, crushed nut shells and ceramic balls. The specimens have been subjected to profilometric analysis, to SEM examinations, microhardness tests and to tribological tests on ball-on-disc stand in Ringer fluid environment. The general results of all tests indicate to favourable effect of shot peening process on the hardness and tribological performance of titanium alloy.
Źródło:: Archives of Metallurgy and Materials; 2019, 64, 1; 377-386
1733-3490
Pojawia się w:: Archives of Metallurgy and Materials
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "shot peening" wg kryterium: Temat

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język