Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "particulate matter emission" wg kryterium: Temat


Tytuł:
Future needs for ship emission abatement and technical measures
Przyszłe potrzeby ograniczania emisji ze statków i techniczne środki ich realizacji
Autorzy:
Antes, T.
Szudyga, M.
Śliwiński, Ł.
Jaworek, A.
Krupa, A.
Balachandran, W.
Di Natale, F.
Gregory, D.
Jackson, M.
Powiązania:
https://bibliotekanauki.pl/articles/374561.pdf
Data publikacji:
2013
Wydawca:
Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:
diesel engine
exhaust gas
diesel particulate matter
electrostatic scrubber
emission control
silnik Diesla
gaz wylotowy
ograniczenie emisji
Opis:
The International Maritime Organization (IMO) has revised air pollution regulations in MARPOL Annex VI. In 2012 Emission Control Areas (ECA) will limit fuel sulphur content to 1% and from 2015 to 0.1%). NOx emissions based on ships engine speed are also reduced for new vessels (2012 & 2016). Facing this legislation, ship owners have the alternative either to operate ships with costly low-sulphur fuels, or to keep using HFO but together with a gas cleaning equipment at the ship stack in order to reduce the rejected amount of SO2 gas in the atmosphere. To achieve this requirement, research and development organizations came out with proposing a solution that uses a device for cleaning exhaust gas of marine diesel engines. The paper presents a short communication about the DEECON project, which aim is to create a novel on-board after-treatment unit more advanced than any currently available. Each sub-unit of the system will be optimized to remove a specific primary pollutant. In particular, the technology within the DEECON system is based on novel or improved abatement techniques for reducing SOx, NOx, Particulate Matter (PM), CO and Volatile Organic Compounds (VOC). Some of these technologies are completely new for the maritime sector and they will represent a breakthrough in the reduction of the atmospheric emissions of ships, moving forward the performance of exhaust gas cleaning systems and fostering and anticipating the adoption of future and tighter regulatory requirements. In addition, an after-treatment strategy enables the possible adoption of alternative fuels, which often have their own emissions characteristics.
Na właścicieli statków i przewoźników morskich spadł obowiązek redukcji zanieczyszczeń pochodzących z ich działalności. Aby spełnić rygorystyczne wytyczne: dyrektyw Wspólnoty europejskiej, międzynarodowej organizacji morskiej (aneks VI, konwencji) MARPOL oraz praw wewnętrznych innych państw należałoby, w obszarach kontroli emisji, używać jako paliwa oleju napędowego o zmniejszonej zawartości siarki. Obszar kontroli emisji jest to obszar obejmujący Morze Bałtyckie, Morze Północne wraz z jego podejściami pod Kanał La-Manche oraz obszar wokół USA. Ze względu na wysokie ceny paliwa niskosiarkowego, duże koszty ewentualnych zmian technicznych przejścia na paliwo o niższej zawartości siarki spowoduje kilkakrotne zwiększenie opłat i zmniejszy atrakcyjność transportu morskiego. Naprzeciw tym wymaganiom wyszły jednostki badawczo rozwojowe, proponując rozwiązania polegające na zastosowaniu nowych, bardziej skutecznych urządzeń do końcowego oczyszczania spalin z okrętowych silników diesla. Artykuł jest komunikatem projektu o akronimie DEECON, którego głównym celem jest opracowanie innowacyjnego pokładowego urządzenia do oczyszczania spalin z okrętowych silników diesla składającego się z różnych modułów. Urządzenie to będzie optymalizowane w celu usunięcia najważniejszych zanieczyszczeń tj. SOx, NOx, PM, Lotnych Związków Organicznych (VOC) oraz tlenku węgla (CO). Niektóre z tych technologii są całkowicie nowe w przemyśle morskim i stanowią przełom w redukcji emisji zanieczyszczeń do atmosfery. Ponadto, takie rozwiązanie jest uniwersalne, umożliwia zastosowanie alternatywnych paliw do zasilania silników okrętowych, które często mają własne cechy emisji.
Źródło:
Transport Problems; 2013, 8, 3; 101-107
1896-0596
2300-861X
Pojawia się w:
Transport Problems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
An overview of particulate matter emissions from modern light duty vehicles
O emisji cząstek stałych z nowoczesnych samochodowych silników spalinowych
Autorzy:
Bielaczyc, P.
Szczotka, A.
Woodburn, J.
Powiązania:
https://bibliotekanauki.pl/articles/133985.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
engine
particulate matter emission
vehicle
silnik
emisja cząstek stałych
pojazd
Opis:
This paper presents a comparison of particle mass and number emissions from different types of vehicles with spark-ignition (SI) engines, with MPI and DI fuelling systems and compression-ignition (CI) engines with DI fuelling system with/without Diesel particles filters (DPF). The methodology of particulate mass and particle number emissions measurement with a full flow dilution tunnel for LDD engines and particulate sampling system is described. The results of measurements performed according to Euro 5/Euro 6 requirements for PC and LDV vehicles are presented, as performed on the chassis dynamometer in the Exhaust Emission Laboratory of BOSMAL Automotive Research and Development Institute (in Bielsko-Biala), Poland.
W artykule przedstawiono porównanie emisji cząstek stałych (masy i liczby) z różnych samochodów z silnikami o zapłonie iskrowym (ZI) z wielopunktowym (MPI) i bezpośrednim wtryskiem paliwa (DI), jak również z silnikami o zapłonie samoczynnym (ZS) z bezpośrednim wtryskiem paliwa oraz bez/z filtrem cząstek stałych (DPF). Opisano metodykę pomiaru masy i liczby cząstek stałych z wykorzystaniem pełno-przepływowego tunelu rozcieńczającego dla samochodów z silnikami diesla i układu pobierania próbki spalin. W artykule przedstawiono wyniki pomiarów wykonanych na hamowni podwoziowej w Laboratorium Badania Emisji Spalin w Instytucie Badań i Rozwoju Motoryzacji BOSMAL, zgodnie z wymaganiami przepisów Euro 5/Euro 6 dla samochodów osobowych i lekkich samochodów użytkowych.
Źródło:
Combustion Engines; 2013, 52, 2; 101-108
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of catalysts on emissions of pollutants from combustion processes of liquid fuels
Wpływ katalizatorów na emisję zanieczyszczeń z procesów spalania paliw ciekłych
Autorzy:
Bok, A.
Guziałowska-Tic, J.
Tic, W. J.
Powiązania:
https://bibliotekanauki.pl/articles/396265.pdf
Data publikacji:
2014
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
air pollution
environmental protection
emission of pollutants
metallic catalyst
particulate matter
soot
zanieczyszczenia powietrza
ochrona środowiska
emisja zanieczyszczeń
katalizator
pyły
sadza
Opis:
The dynamic growth of the use of non-renewable fuels for energy purposes results in demand for catalysts to improve their combustion process. The paper describes catalysts used mainly in the processes of combustion of motor fuels and fuel oils. These catalysts make it possible to raise the efficiency of oxidation processes simultanously reducing the emission of pollutants. The key to success is the selection of catalyst compounds that will reduce harmful emissions of combustion products into the atmosphere. Catalysts are introduced into the combustion zone in form of solutions miscible with fuel or with air supplied to the combustion process. The following compounds soluble in fuel are inclused in the composition of the described catalysts: organometallic complexes, manganese compounds, salts originated from organic acids, ferrocen and its derivatives and sodium chloride and magnesium chloride responsible for burning the soot (chlorides). The priority is to minimize emissions of volatile organic compounds, nitrogen oxides, sulphur oxides, and carbon monoxide, as well as particulate matter.
Dynamiczny wzrost stosowania paliw nieodnawialnych dla celów energetycznych powoduje zapotrzebowanie na katalizatory poprawiające proces ich spalania. W pracy omówiono katalizatory stosowane głównie w procesach spalania paliw silnikowych i olejów opałowych. Katalizatory te pozwalają na podniesienie efektywności procesów utleniania powodując tym samym redukcję emisji zanieczyszczeń. Kluczem do sukcesu jest taki dobór składników katalizatora, który zapewni ograniczenie emisji szkodliwych produktów spalania do atmosfery. Katalizatory wprowadzane są do strefy spalania jako roztwory mieszające się z paliwem, lub do powietrza dostarczanego do procesu spalania. W skład omawianych katalizatorów wchodzą rozpuszczalne w paliwie: kompleksy metaloorganiczne, związki manganu, sole kwasów organicznych, ferrocen i jego pochodne oraz chlorek sodu i chlorek magnezu odpowiedzialne za spalanie sadzy. Priorytetem jest minimalizacja emisji lotnych związków organicznych, tlenków azotu, tlenków siarki i tlenku węgla oraz cząstek stałych.
Źródło:
Civil and Environmental Engineering Reports; 2014, 13; 5-17
2080-5187
2450-8594
Pojawia się w:
Civil and Environmental Engineering Reports
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania emisji cząstek stałych z układu hamulcowego pojazdu samochodowego
A study of the particulate matter emission from the braking systems of motor vehicles
Autorzy:
Chłopek, Z.
Jakubowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/301425.pdf
Data publikacji:
2009
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
pojazdy samochodowe
układ hamulcowy
emisja cząstek stałych
motor vehicles
braking systems
emission of particulate matter
Opis:
W pracy przedstawiono problem emisji cząstek stałych, związanej z ruchem pojazdów samochodowych. Zwrócono uwagę na szczególne zagrożenie przez pyły emitowane z par trybologicznych pojazdu, przede wszystkim z układu hamulcowego. W celu zbadania zjawiska emisji cząstek stałych z układu hamulcowego opracowano i wykonano specjalne stanowisko badawcze, umożliwiające pomiar emisji cząstek stałych dla różnych warunków pracy par trybologicznych. Opracowano układ do zmniejszania emisji cząstek stałych z układu hamulcowego w postaci specjalnej ssawki, umieszczonej za zaciskiem tarczy hamulcowej. W wyniku przeprowadzonych badań wstępnych stwierdzono możliwość zmniejszenia emisji cząstek stałych z układu hamulcowego nawet więcej niż o 70% dzięki zastosowaniu opracowanego układu.
This paper looks at the question of particulate matter emission in connection with motor vehicle traffic. Attention is called to the special threat posed by particulate matter emitted from a vehicle's tribological vapors, primarily as stemming from the braking system. A special test stand allowing the measurement of particulate matter emission subject to various modes of tribological vapor activity was designed and built in order to examine the phenomenon of the emission of particulate matter by braking systems. A system for decreasing the emission of particulate matter from braking systems has been developed in the form of special suction nozzles placed behind the disc brake caliper. Preliminary tests as conducted show that it is possible to decrease the emission of particulate matter from braking systems by even more than 70% thanks to the application of the developed system.
Źródło:
Eksploatacja i Niezawodność; 2009, 4; 45-52
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania modelu ograniczania emisji cząstek stałych z układu hamulcowego pojazdu samochodowego
The examination of the reduction of particulate matter emission from motor vehicle braking systems
Autorzy:
Chłopek, Z.
Jakubowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/300913.pdf
Data publikacji:
2010
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
pojazdy samochodowe
układ hamulcowy
emisja cząstek stałych
modelowanie
motor vehicles
braking system
particulate matter emission
modeling
Opis:
W pracy przedstawiono badania modelu ograniczania emisji cząstek stałych z układu hamulcowego pojazdu samochodowego. Modelowano zjawiska zachodzące w opracowanym przez autorów układzie do podciśnieniowego ograniczania emisji cząstek stałych z układu hamulcowego pojazdu samochodowego. Do opisu zjawisk zastosowano model behawiorystyczny w postaci funkcji stopnia drugiego zmiennych niezależnych: podciśnienia w układzie ssącym oraz temperatur tarczy hamulcowej dla włączania i wyłączania wyciągu. Do celów identyfikacji modelu przeprowadzono badania empiryczne na zmodyfikowanym stanowisku Kraussa. Na podstawie badań zidentyfikowanego modelu oceniono wpływ zmiennych niezależnych na skuteczność zmniejszania emisji cząstek stałych z układu hamulcowego. Przeprowadzono również analizę korelacyjną zmiennych niezależnych i skuteczności zmniejszania emisji cząstek stałych. Oceniono, że największy wpływ na skuteczność zmniejszania emisji cząstek stałych ma podciśnienie w układzie ssącym. Wyniki badań upoważniają do zastosowania opracowanej metody badań do prac nad ograniczaniem emisji cząstek stałych z układu hamulcowego w warunkach eksploatacji pojazdu.
This work presents the testing of a model for reducing particulate matter emission from the braking systems of motor vehicles. The model describes the phenomena taking place in the negative pressure system - as developed by the authors - for reducing the emission of particulate matter from motor vehicle braking systems. A behaviorist model in the form of a quadratic function with independent variables - the negative pressure in the suction system and the temperature of the brake discs for engaging and disengaging the extraction - was used to describe the phenomena. Empirical tests were conducted on a modified Krauss test machine in order to identify the model. It is on the basis of tests on the identified model that the impact of independent variables on the effectiveness of the reduction in emission of particulate matter from the braking system was evaluated. A correlation analysis of the independent variables and of the effectiveness of the reduction in particulate matter was also conducted. It was assessed that the greatest influence on the effectiveness of the reduction in particulate matter is affected by the negative pressure in the suction system. Test results justify the application of the developed method of testing for work on reducing the emission of particulate matter from braking systems subject to conditions of vehicle operation.
Źródło:
Eksploatacja i Niezawodność; 2010, 4; 29-36
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Spatial analysis of air masses backward trajectories in order to identify distant sources of fine particulate matter emission
Analiza przestrzenna wstecznych trajektorii mas powietrza w celu rozpoznania odległych źródeł emisji pyłu drobnego
Autorzy:
Godłowska, J.
Hajto, M. J.
Tomaszewska, A. M.
Powiązania:
https://bibliotekanauki.pl/articles/204690.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
backward trajectories
air masses
emission sources
particulate matter
PM2.5
trajektoria wsteczna
masy powietrza
źródła emisji
pył zawieszony
Opis:
The paper presents a method of identifying distant emission sources of fine particulate matter PM2.5 affecting significantly PM2.5 concentrations at a given location. The method involves spatial analysis of aggregate information about PM2.5 concentrations measured at the location and air masses backward trajectories calculated by HYSPLIT model. The method was examined for three locations of PM2.5 measurement stations (Diabla Góra, Gdańsk, and Katowice) which represented different environmental conditions. The backward trajectories were calculated starting from different heights (30, 50, 100 and 150 m a. g. l.). All points of a single backward trajectory were assigned to the PM2.5 concentration corresponding to the date and the site of the beginning of trajectory calculation. Daily average concentrations of PM2.5 were used, and in the case of Gdańsk also hourly ones. It enabled to assess the effectiveness of the presented method using daily averages if hourly ones were not available. Locations of distant sources of fine particulate matter emission were determined by assigning to each grid node a mean value of PM2.5 concentrations associated with the trajectories points located within the so-called search ellipse. Nearby sources of fine particulate matter emission were eliminated by filtering the trajectories points located close to each other (so-called duplicates). The analyses covered the period of January-March 2010. The results indicated the different origin of air masses in the northern and southern Poland. In Diabla Góra and Gdańsk the distant sources of fine particulate matter emission are identified in Belarus and Russia. In Katowice the impact of the Belarusian PM2.5 emission sources was also noted but as the most important fine particulate matter emission sources were considered those located in the area of Romania, Hungary, Slovakia and Ukraine.
W pracy zaprezentowano metodę rozpoznawania odległych źródeł emisji pyłu drobnego PM2.5, polegającą na przestrzennej analizie łącznej informacji o imisji PM2.5 oraz o wstecznych trajektoriach mas powietrza, obliczonych za pomocą modelu HYSPLIT. Trajektorie wsteczne obliczono startując z wysokości 30, 50, 100 i 150 m n.p.g., dla trzech lokalizacji stacji pomiarowych stężeń PM2.5 (Diabla Góra, Gdańsk, Katowice), reprezentujących różne warunki środowiskowe. Wszystkim punktom pojedynczej trajektorii wstecznej przyporządkowano stężenie PM2.5 odpowiadające dacie startu obliczeń tej trajektorii. Użyto dobowych średnich stężeń PM2.5, a w przypadku Gdańska dodatkowo także godzinnych średnich, co umożliwiło ocenę skuteczności przedstawionej metody. Położenie odległych źródeł emisji pyłu drobnego zostało określone poprzez interpolację danych punktowych trajektorii do regularnej siatki przy zastosowaniu metody metryki danych. Każdemu węzłowi siatki przypisano wartość średnią obliczoną ze stężeń PM2.5 przyporządkowanych punktom trajektorii znajdujących się w obrębie tzw. elipsy wyszukiwania. Przed obliczeniem wartości średniej ukryto część danych, eliminując w ten sposób bliskie źródła emisji pyłu drobnego. Analizy objęły okres styczeń-marzec 2010 roku. Wyniki wskazały na odmienne pochodzenie mas powietrza w północnej i południowej Polsce. W Diablej Górze i Gdańsku odległe źródła emisji pyłu drobnego rozpoznano głównie w Białorusi i Rosji. W Katowicach również zaznaczył się wpływ źródeł białoruskich, ale jako najbardziej istotne odległe źródła emisji PM2.5 uznano te zlokalizowane na obszarze Rumunii, Węgier, Słowacji i Ukrainy.
Źródło:
Archives of Environmental Protection; 2015, 41, 2; 28-35
2083-4772
2083-4810
Pojawia się w:
Archives of Environmental Protection
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Particulate matter emission from diesel engine fuelled with blends of diesel oil and ethyl tert-butyl ether
Emisja cząstek stałych z silnika o zapłonie samoczynnym zasilanego mieszaninami oleju napędowego z eterem etylo-tert-butylowym
Autorzy:
Górski, K.
Lotko, W.
Swat, M.
Powiązania:
https://bibliotekanauki.pl/articles/263295.pdf
Data publikacji:
2010
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
emisja cząsteczek stałych
ETBE
olej napędowy
silnik o zapłonie samoczynnym
diesel engine
diesel oil
particulate matter emission
Opis:
The article presents the results of research on particulate matter (PM) emission from ADCR diesel engine fuelled with blends of diesel oil and ethyl tert-butyl ether (ETBE). Measurements were done in conditions of 13-phase, stationary ECE R49 test. Results show, that PM emission was reduced with the use of all tested ETBE/diesel blends with respect to those of the neat diesel fuel. In case of tested engine fuelled with mixture ETBE20 its PM emission was decreased by a half when compared to diesel oil.
Artykuł przedstawia wyniki badań w zakresie oceny emisji cząstek stałych z silnika ADCR zasilanego mieszaninami oleju napędowego z eterem etylo-tert-butylowym (EETB). Pomiary wykonano w warunkach 13-fazowego testu stacjonarnego ECE R49. Wyniki wskazują, że emisja cząstek stałych była obniżona dla wszystkich badanych mieszanin w porównaniu do tej, którą uzyskano dla oleju napędowego. W przypadku badanego silnika zasilanego mieszaniną ETBE20 jego emisja cząstek stałych była obniżona o połowę w stosunku do zasilania olejem napędowym.
Źródło:
Archiwum Motoryzacji; 2010, 2; 119-126
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the effectiveness of operation of a system to reduce particulate matter emission from the motor vehicle braking system in the conditions of special driving tests
Ocena skuteczności układu do ograniczania emisji cząstek stałych z układu hamulcowego samochodu w warunkach specjalnych testów jezdnych
Autorzy:
Kieracińska, A.
Chłopek, Z.
Biedrzycki, J.
Jakubowski, A.
Lasocki, J.
Wójcik, P.
Powiązania:
https://bibliotekanauki.pl/articles/133883.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
particulate matter emission
braking systems
motor vehicles
emisja cząstek stałych
układy hamulcowe
pojazdy samochodowe
Opis:
Particulate matter is counted among the air pollutants that are particularly harmful to human health. An important source of the emission of this substance is motor traffic. A significant part of the particulate matter emission from the motorization–related sources comes from the tribological pairs existing in motor vehicles, chiefly from their braking systems. This paper presents results of empirical tests of a system to reduce the emission of particulate matter from the braking system. The tests were carried out on a vehicle chassis dynamometer in the conditions of special driving tests. The effectiveness of operation of the system under tests was found to be good: the particulate matter emission was reduced by about 50 to 75%.
Cząstki stałe należą do zanieczyszczeń powietrza szczególnie szkodliwych dla zdrowia ludzi. Istotnym źródłem ich emisji są pojazdy samochodowe. Znaczna część emisji cząstek stałych ze źródeł motoryzacyjnych pochodzi z par trybologicznych pojazdów, przede wszystkim z układu hamulcowego. W pracy przedstawiono wyniki badań empirycznych urządzenia do ograniczania emisji cząstek stałych z układu hamulcowego. Badania przeprowadzono na stanowisku hamowni podwoziowej w warunkach specjalnych testów jezdnych. Stwierdzono dobrą skuteczność urządzenia – zmniejszenie emisji cząstek stałych o około (50 ÷ 75)%.
Źródło:
Combustion Engines; 2013, 52, 3; 208-213
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Examing of the effectiveness of operation of a system to reduce particulate matter emission from motor vehicle brake mechanisms in conditions simulating the real vehicle use
Badania skuteczności urządzeń do zmniejszania emisji cząstek stałych z układu hamulcowego samochodu w warunkach symulujących rzeczywiste użytkowanie pojazdu
Autorzy:
Kieracińska, A.
Biedrzycki, J.
Chłopek, Z.
Jakubowski, A.
Lasocki, J.
Wójcik, P.
Powiązania:
https://bibliotekanauki.pl/articles/1364500.pdf
Data publikacji:
2014
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
exhaust emissions
particulate matter emission
braking systems
motor vehicles
emisja spalin
emisja cząstek stałych
układy hamulcowe
pojazdy samochodowe
Opis:
The devices to reduce particulate matter emission from disc brake and drum brake mechanisms of motor vehicles successfully passed rig tests carried out on laboratory test stands. In this paper results of testing the devices installed in a passenger car have been presented. The tests were carried out on a vehicle chassis dynamometer in the conditions of special driving tests. The effectiveness of operation of the system under consideration was found to be good: the particulate matter emission was reduced by about 50 to 70%. The examinations have revealed that the brake dusts comprise particles of very small dimensions and that heavy metals are among the major particle components. Results of test carried out when the test vehicle was driven in real urban traffic confirmed high effectiveness of operation of the system developed. However, the road test results were not as good as the results obtained from the chassis dynamometer tests because of some design problems that emerged at the installation of an autonomous system version in the test vehicle. The experience gained at the road tests is now used for modifying the system to reduce dust emission from motor vehicle brake mechanisms.
Urządzenia do zmniejszania emisji cząstek stałych z tarczowych i bębnowych układów hamulcowych samochodu zostały pozytywnie przebadane na stanowiskach laboratoryjnych. W niniejszej pracy przedstawiono wyniki badań opracowanych urządzeń zamontowanych w samochodzie osobowym. Badania przeprowadzano na stanowisku hamowni podwoziowej w warunkach specjalnych testów jezdnych. Stwierdzono dobrą skuteczność urządzenia - zmniejszenie emisji cząstek stałych o około (50 ÷ 70) %. Stwierdzono, że pyły z układu hamulcowego zawierają ziarna o bardzo małych wymiarach, a w skład cząstek wchodzą m.in. metale ciężkie. W wyniku badań w czasie użytkowania pojazdu w ruchu w miejskim uzyskano potwierdzenie skuteczności opracowanych urządzeń, jednak ze względu na problemy konstrukcyjne zabudowy urządzeń w wersji autonomicznej wyniki nie były tak pozytywne jak w przypadku wyników z hamowni podwoziowej. Wnioski z badań trakcyjnych są wykorzystywane do modyfikacji urządzeń do zmniejszania emisji cząstek stałych z układu hamulcowego samochodu.
Źródło:
Archiwum Motoryzacji; 2014, 63, 1; 35-50
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Estimating shipping emissions – A case study for cargo Port of Zadar, Croatia
Autorzy:
Knezević, V.
Pavin, Z.
Čulin, J.
Powiązania:
https://bibliotekanauki.pl/articles/2063981.pdf
Data publikacji:
2021
Wydawca:
Uniwersytet Morski w Gdyni. Wydział Nawigacyjny
Tematy:
Port of Zadar
air pollutant emission
estimating shipping emissions
nitrogen oxides
particulate matter
volatile organic compounds
carbon dioxide
green port
Opis:
Reducing air pollutant emissions and energy consumption, as a necessary step to make ports more sustainable, is one of the crucial tasks and challenges of port management. Some of the port strategies to meet the term “green port” usually include reducing fuel consumption from vessels and vehicles in ports. This paper estimates the emission inventory of maritime traffic for the cargo Port of Zadar. For this research, emissions from cargo ships are estimated in the period from January 01. 2018 until October 01. 2019. The “bottom-up” methodology has been applied for estimating emissions, which includes detailed data on the ship’s characteristics (engine power, the load factor, fuel type, the emission factor) and time spent cruising and hotelling. The emissions from cargo ships have been estimated for three ship’s activities: cruising in the reduced speed zone, hotelling (time spent at berth), and maneuvering. The emission results (tons/year) refer to the pollutants such as nitrogen oxides (NOx), sulphur oxides (SOx), particulate matter (PM), volatile organic compounds (VOC), and carbon dioxide (CO2) which represents greenhouse gases. Estimating emission inventory is the first step for planning effective port air quality control. Some recommendations for reducing emissions in port areas are emphasized in this paper.
Źródło:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation; 2021, 15, 3; 615--620
2083-6473
2083-6481
Pojawia się w:
TransNav : International Journal on Marine Navigation and Safety of Sea Transportation
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analiza rozkładu stężeń pyłu zawieszonego frakcji PM10, PM2,5 i PM1,0 na różnych wysokościach Mostu Gdańskiego
Analysis of Concentrations of Particulate Matter PM10, PM2,5 and PM1,0 at Different Heights of the Gdański Bridge
Autorzy:
Kuskowska, K.
Dmochowski, D.
Powiązania:
https://bibliotekanauki.pl/articles/137094.pdf
Data publikacji:
2016
Wydawca:
Szkoła Główna Służby Pożarniczej
Tematy:
pył zawieszony
liniowa emisja zanieczyszczeń
particulate matter
linear emission of pollution
Opis:
W artykule przedstawiono wyniki badań pyłów zawieszonych w miejskim powietrzu atmosferycznym, przeprowadzonych w obrębie Mostu Gdańskiego – jednego z ciągów komunikacyjnych łączących prawo- i lewobrzeżną Warszawę. Celem badań było dokonanie analizy wpływu wytypowanych liniowych źródeł zanieczyszczenia na jakość powietrza w tym rejonie Warszawy. Badania przeprowadzono na trzech wysokościach: na Wisłostradzie, przy torach tramwajowych Mostu Gdańskiego, około 4 m od jezdni Wisłostrady, oraz przy jezdni Mostu Gdańskiego, tj. na wysokości około 9 m od jezdni Wisłostrady. Otrzymane wyniki zaprezentowano w postaci wykresów i tabel, w których przedstawiono oddziaływanie transportu na jakość powietrza, a tym samym na poziom bezpieczeństwa ekologicznego w rejonie Mostu Gdańskiego.
The paper presents the results of the research concerning the dust from the linear sources of pollution emitted on the Gdanski Bridge – one of the bridges of Warsaw agglomeration. It is a route often frequented by drivers and place enjoyed by the citizens of Warsaw for recreational purposes. The aim of the study was to analyze the influence of linear sources of pollution on quality of air in the region. The study was performed in 3 heights: the Wislostrada, the tram tracks of the Gdanski bridge and the road of the Gdanski bridge. The results are presented in the graphs and tables showing the impact of transport on air quality and thereby on the level of ecological safety in this region.
Źródło:
Zeszyty Naukowe SGSP / Szkoła Główna Służby Pożarniczej; 2016, 3, 59; 101-119
0239-5223
Pojawia się w:
Zeszyty Naukowe SGSP / Szkoła Główna Służby Pożarniczej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena redukcji niskiej emisji po modernizacji budynku przy różnych wariantach nośników energii
Assessment of low emission reduction after modernization of building by different variants of fuel type selecting
Autorzy:
Lis, A.
Ujma, A.
Powiązania:
https://bibliotekanauki.pl/articles/2065426.pdf
Data publikacji:
2017
Wydawca:
Politechnika Częstochowska
Tematy:
nośniki energii
niska emisja
benzo(a)piren
pyły zawieszone
termomodernizacja budynków
fuel combustion
low emission
benzo(a)pyrene
particulate matter
thermal modernization of the building
Opis:
W artykule przedstawiono problem występowania niskiej emisji związanej z ogrzewaniem i przygotowaniem ciepłej wody użytkowej oraz jej wpływu na kształ- towanie się jakości powietrza w Polsce. Wyszczególniono produkty spalania wchodzące w skład niskiej emisji. Podano najwyższe średnie roczne wartości stężeń B(a)P w 2015 roku oraz średnie roczne i średnie dobowe wartości stężeń PM10 i PM2.5. Omówiono działania termomodernizacyjne zrealizowane w budynku szkoły. Dokonano oceny możliwości redukcji niskiej emisji w przypadku zastosowania nowego kotła na węgiel kamienny, drewno, gaz ziemny oraz olej opałowy.
The article presents the problem of low emissions associated with heating and hot water preparation and its influence on the air quality in Poland. The low emission combustion products are listed. The highest average annual concentrations of B(a)P in 2015 and average annual and average daily concentrations of PM10 and PM2.5 are given. The thermal modernization activities implemented in school buildings are discussed. The assessment of potential for low emission reductions in the case of a coal, wood, gas and oil using are performed.
Źródło:
Budownictwo o Zoptymalizowanym Potencjale Energetycznym; 2017, 1 (19); 121--128
2299-8535
2544-963X
Pojawia się w:
Budownictwo o Zoptymalizowanym Potencjale Energetycznym
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Direct application of non-thermal plasma to PM reduction from marine diesel engines
Autorzy:
Myśków, J.
Borkowski, T.
Powiązania:
https://bibliotekanauki.pl/articles/242305.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
exhaust emission
particulate matter
non-thermal plasma reactor
Opis:
This paper describes the experimental method - using non-thermal plasma reactor to cleaning exhaust gases - focused on PM compound. The demonstrator NTP reactor assembly was built as the by-pass in the real exhaust gas after-treatment system, in marine diesel engine. The reactor used to experiment is called - DBD (dielectric barrier discharge) type, The main aim of investigation was to analyze exhaust gas PM compounds under steady load of the engine. Test bench construction enables direct exhaust stream (main exhaust duet by-pass) to plasma reactor exposure with no additional components (coolers, orifices) that can change the exhaust gas properties. A new monitoring PM analyzing system, which can measure soot and SOF in low mass level, has been engaged. It consist of a diffusion charging (DC) detector with a dilution device for soot measurement, and two differential flame ionization detection (FID) method, which uses two FID detectors with separate sample lines. Exhaust emission reduction strategy for ships, Particulate Matters - PM in exhaust gas, non-thermal plasma reactor, experimental test bed and procedure, an example of reactor power measurement, test results provided into seven stages are presented in the paper.
Źródło:
Journal of KONES; 2009, 16, 2; 361-367
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Marine engine exhaust gas emission aftertreatment system concept
Autorzy:
Myśków, J.
Borkowski, T.
Bludszuweit, M.
Frohlingsdorf, W.
Powiązania:
https://bibliotekanauki.pl/articles/247178.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
exhaust emission
particulate matter
non-thermal plasma reactor
Opis:
In 2008 the International Maritime Organization - IMO decided to strengthen the requirements for new ships from 2011 - Tier II. However, for Emission Control Areas (ECAs), such as the Baltic Sea, stringent rules will apply from 1 January 2016 for new ships - Tier III. The new standards introduce restrictions on exhaust emissions from diesel engines - NOx and SOx. The paper presents proposal of new design an existing exhaust gas system of experimental marine diesel engine, which is situated in the Laboratory of Maritime Academy in Szczecin. The conception is due to meet to new environmental regulations. Arrangements of exhaust line, CFD model of the SCR reference plant, CFD model - inlet and outlet boundary conditions, pressure loss model for the catalytic elements, simulation results - streamlines, velocity distribution, reaction progress distribution ate presented in the paper as well design description of system of laboratory- 4-stroke and turbocharged engine. . The means of the reduction systems are based on conventional marine exhaust gas installation that includes noise silencer and soot-catcher. The after-treatment methods do not introduce significant changes in engine arrangement and operation. A new gas purifying system should be installed in the engine exhaust gas system.
Źródło:
Journal of KONES; 2011, 18, 4; 307-315
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Air quality assessment in the municipality of Wadowice
Autorzy:
Petryk, A.
Powiązania:
https://bibliotekanauki.pl/articles/101257.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Stowarzyszenie Infrastruktura i Ekologia Terenów Wiejskich PAN
Tematy:
low emission
boilers
pollution
PM10 particulate matter
Opis:
The article presents an analysis of pro-ecological activities in the municipality of Wadowice in the field of air quality protection against the effects of low emission. Research conducted by the Provincial Inspectorate for Environmental Protection in Krakow indicated that in the town of Wadowice, the capital of the municipality, in the period from October till March, the permissible level of particulate matter (PM10) was exceeded on average approximately 16 times within one month. The municipality of Wadowice is one of the most polluted municipalities of the Małopolska voivodeship. The elaborated municipal Low-Emission Economy Plan, updated in 2017, is coherent with the climate and energy package and implements the guidelines of the new European Union 2020 strategy for economic and social development. Until 2015, the municipality had implemented the KAWKA program, which led to liquidation of 11 coal-fired boiler rooms and installation of 11 new boiler rooms. The continuation of the system in 2016 enabled the closure of further 31 coal-fired boiler rooms and the assembly of new boiler rooms and 10 solar panel installations in order to reduce emissions in the local fuel-fired heat source.
Źródło:
Infrastruktura i Ekologia Terenów Wiejskich; 2018, IV/1; 909-921
1732-5587
Pojawia się w:
Infrastruktura i Ekologia Terenów Wiejskich
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies