Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "mechanical load" wg kryterium: Temat


Tytuł:
Applicability of notch stress-strain correction methods to low-cycle fatigue life prediction of turbine rotors subjected to thermomechanical loads
Autorzy:
Banaszkiewicz, M.
Dudda, W.
Powiązania:
https://bibliotekanauki.pl/articles/386989.pdf
Data publikacji:
2018
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
low-cycle fatigue
turbine rotors
thermo-mechanical load
Opis:
The paper analyses the possibility of using analytical methods of notch stress-strain correction in low-cycle fatigue life predictions of steam turbine rotors operating under non-isothermal conditions. The assessment was performed by comparing strain amplitudes calculated using the Neuber and Glinka-Molski methods and those predicted by the finite element analysis (FEA) employing elastic-plastic material model. The results of investigations reveal that the Neuber method provides an upper bound limit, while the GlinkaMolski method results in a lower bound limit of strain amplitude. In the case of rotor heat grooves, both methods provide equally accurate results of notch strain amplitude and are suited to estimating lower and upper bound limits of low-cycle fatigue life under non-isothermal conditions.
Źródło:
Acta Mechanica et Automatica; 2018, 12, 3; 179-185
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Określenie obciążenia mechanicznego i cieplnego silnika okrętowego pracującego z wybranymi niesprawnościami, w stosunku do poziomu tych obciążeń dla silnika technicznie sprawnego
Definition of the mechanical and thermal loads on the marine engine working with selected technical failures in comparison to the loads level of the engine working with the proper technical condition
Autorzy:
Turzyńska, K.
Powiązania:
https://bibliotekanauki.pl/articles/250146.pdf
Data publikacji:
2016
Wydawca:
Instytut Naukowo-Wydawniczy TTS
Tematy:
silnik okrętowy
obciążenie mechaniczne
obciążenie cieplne
motor ship
mechanical load
thermal load
Opis:
W artykule omówione zostały sposoby określenia obciążenia cieplnego i mechanicznego silnika okrętowego pracującego w normalnych warunkach oraz z wybranymi niesprawnościami. Badanie polegało na pomiarze parametrów pracy silnika z symulowaną uszkodzoną turbosprężarką oraz symulowaną nieszczelną pompą wtryskową i porównanie ich do parametrów pracy silnika technicznie sprawnego. Badania zostały przeprowadzone w warunkach laboratoryjnych na silniku SULZER 3AL25/30.
The article explains how to determine the thermal and mechanical loads on the marine engine working with normal operating conditions and with selected technical failures. The survey has been based on comparison between the parameters of the engine operating with simulated damaged turbocharger and leaking simulated injection pump, and the engine working in a proper technical condition. The research has been conducted SULZER 3AL25/30 engine, under laboratory conditions
Źródło:
TTS Technika Transportu Szynowego; 2016, 12; 255-259
1232-3829
2543-5728
Pojawia się w:
TTS Technika Transportu Szynowego
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelling the effects of repeated wheel loads on soil profiles
Autorzy:
Richards, B.G.
Baumgartl, T.
Horn, R.
Grasle, W.
Powiązania:
https://bibliotekanauki.pl/articles/25769.pdf
Data publikacji:
1997
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
soil profile
porosity measurement
mechanical load
soil productivity
aggregate degradation
root penetration
soil compaction
wheel load
Źródło:
International Agrophysics; 1997, 11, 3
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Geometric properties of grasspea seeds and their mechanical loads
Autorzy:
Rybinski, W.
Szot, B.
Bocianowski, J.
Rusinek, R.
Powiązania:
https://bibliotekanauki.pl/articles/25034.pdf
Data publikacji:
2011
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
geometrical property
grass pea
mechanical load
multivariate statistical analysis
seed
seed geometry
plant cultivar
Źródło:
International Agrophysics; 2011, 25, 3
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Research on Characterization of Crushability for Foundry Sand Particles
Autorzy:
Dai, Y.
Ma, Q. Y.
Li, X. H.
Zhang, X.
Hu, F. P.
Zhang, Y.
Xie, W. D.
Powiązania:
https://bibliotekanauki.pl/articles/379689.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
foundry sand particle
mechanical load
AFS grain fineness
crushability
piasek odlewniczy
obciążenie mechaniczne
rozdrobnienie ziarna
Opis:
In this paper, crushability of foundry sand particles was studied. Three kinds of in-service silica sands in foundry enterprises selected as the study object, and foundry sand particles were subjected to mechanical load and thermal load during service were analyzed. A set of methods for simulating mechanical load and thermal load by milling and thermal-cold cycling were designed and researched, which were used to characterize the crushability for silica sand particles, the microstructure was observed by SEM. According to the user’s experience in actual application, the crushability of Sand C was the best and then Sand B, the last Sand A. The results indicated that mechanical load, thermal load and thermal-mechanical load can all be used to characterize the crushability of foundry sand particles. Microscopic appearances can qualitatively characterize the crushability of foundry sand particles to a certain extent, combining with the additions and cracks which are observed on the surface.
Źródło:
Archives of Foundry Engineering; 2017, 17, 4; 231-235
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Basic Principles and Mechanical Considerations of Satellites: A Short Review
Autorzy:
Reda, Reham
Ahmed, Yasmeen
Magdy, Islam
Nabil, Hossam
Khamis, Mennatullah
Refaey, Ahmed
Eldabaa, Nada
Abo Elmagd, Manar
Abo Lila, Mohamed
Ergawy, Hady
Elgarf, Alhussein
Abed, Gerges
Powiązania:
https://bibliotekanauki.pl/articles/36827035.pdf
Data publikacji:
2023
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
principles of satellites
primary structure
isogrid structure
honeycomb structure
mechanical load analysis
assembly
integration
testing
Opis:
Satellites are used for navigation, communication, oceanography, astronomy, etc.. Satellites come in a diversity of sizes and forms. Depending on the satellite’s mission, different subsystems are used. These subsystems are installed inside a housing to protect them from the space environment. This housing, which is also known as the satellite primary structure or mechanical structure, is made of durable materials that can endure severe conditions during launch and in the orbit. The optimisation of satellite mass is crucial right now since satellites are losing mass every day to reduce the cost of manufacturing and launching. This review first introduces an overview of the satellite classifications and subsystems. Then, the different types of mechanical load analysis the satellite subjects itself to are demonstrated. The advanced approaches for promoting the performance of the mechanical structures of satellites are explored, with a spotlight on the effect of the optimisation parameters of isogrid and honeycomb sandwich structures on the mechanical performance of the satellite primary structure. The assembly, integration and testing (AIT) of the small satellite are briefly presented. Finally, the important potential designs to improve the mechanical performance of the satellite primary structure and the challenges of further research are summarised.
Źródło:
Transactions on Aerospace Research; 2023, 3 (272); 40-54
0509-6669
2545-2835
Pojawia się w:
Transactions on Aerospace Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
State of strength in massive concrete structure subjected to non-mechanical loads
Autorzy:
Łydżba, D.
Sobótka, M.
Powiązania:
https://bibliotekanauki.pl/articles/178618.pdf
Data publikacji:
2014
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
non-mechanical load
massive concrete structure
hydro power plant
temperature impact
obciążenia niemechaniczne
beton masywny
elektrownia wodna
wpływ temperatury
Opis:
The paper deals with an impact of non-mechanical loads on the state of strength in massive concrete hydraulic structures. An example of hydroelectric plant subjected to the effect of water temperature annual fluctuation is considered. Numerical analysis of transient thermal-elasticity problem was performed. After determining the temperature distributions within the domain, the Duhamel–Neumann set of constitutive equations was employed to evaluate fields of mechanical quantities: displacement, strain and stress. The failure criterion proposed by Pietruszczak was adopted in assessing whether the load induces exceeding of strength of concrete within the structure volume. The primary finding is that the temperature effect can lead to damage of concrete in draft tubes and spirals, especially in winter months.
Źródło:
Studia Geotechnica et Mechanica; 2014, 36, 2; 37-43
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Obciążenia podłóg przemysłowych
Loads of industrial floors
Autorzy:
Hajduk, P.
Powiązania:
https://bibliotekanauki.pl/articles/161017.pdf
Data publikacji:
2017
Wydawca:
Polski Związek Inżynierów i Techników Budownictwa
Tematy:
podłoga przemysłowa
obciążenie
obciążenie statyczne
obciążenie dynamiczne
obciążenie montażowe
obciążenie mechaniczne
oddziaływanie chemiczne
obciążenie cieplne
obciążenie skurczowe
industrial floor
load
static load
dynamic load
assembly load
mechanical load
chemical impact
thermal load
shrinkage load
Opis:
Podłogi przemysłowe mają bardzo różne przeznaczenie, dlatego powinny spełniać specjalne wymagania. Płyta nośna musi przenosić duże obciążenia skupione i powierzchniowe pochodzące od ciężkich maszyn, składowanych produktów i poruszających się po niej pojazdów. Oprócz tych obciążeń, w trakcie produkcji, na posadzkę mogą oddziaływać maszyny pracujące dynamicznie, obciążenia od temperatury i skurczu betonu. Wszystkie te obciążenia muszą zostać przejęte bez deformacji, osiadań i zarysowania.
Industrial floors are intended for many different uses, therefore they should meet special requirements. The load plate must carry significant concentrated and surface loads deriving from heavy machinery, stored products and moving vehicles. Apart from these loads, during manufacturing, the flooring may be affected by dynamically working machines, loads resulting from temperature and concrete shrinkage. All these loads need to be carried without deformations, sinking and scratches.
Źródło:
Przegląd Budowlany; 2017, 88, 7-8; 67-76
0033-2038
Pojawia się w:
Przegląd Budowlany
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
PV installations and the safety of residential buildings
Autorzy:
Litzbarski, Leszek S.
Seklecki, Konrad
Adamowicz, Marek
Grochowski, Jacek
Powiązania:
https://bibliotekanauki.pl/articles/27323685.pdf
Data publikacji:
2023
Wydawca:
Centrum Rzeczoznawstwa Budowlanego Sp. z o.o.
Tematy:
safety of construction
mechanical load calculation
thermal impact simulation
PV installation
photovoltaic
PV
fotowoltaika
Instalacje fotowoltaiczne
bezpieczeństwo konstrukcji
symulacja wpływu termicznego
obliczanie obciążenia mechanicznego
Opis:
The dynamic development of the photovoltaic industry entails threats that have a direct impact on the safety of residential buildings. Appropriate design of a PV installation can be a challenge due to the multifaceted nature of this issue. The designer should take into account issues related to the selection of electrical parameters of the installation, adapting lightning and surge protection in accordance with applicable standards, ensure the optimization of the system in terms of efficiency and fire safety and calculate the mechanical stress on the rooftop. Unfortunately, most PV installations in Poland are built without any engineering project, which is allowed by the current law. In this article, we describe the results of simulations of real mechanical loads inflicted from the installation of PV panels on flat roofs for various regions of Poland. We also present the results of the simulation of the thermal impact of hot-spots on the roof surface, which can be a potential source of fire. In addition, we propose changes to the regulations that may increase the safety of PV installations mounted on the roofs of residential buildings.
Źródło:
Inżynieria Bezpieczeństwa Obiektów Antropogenicznych; 2023, 4; 1--10
2450-1859
2450-8721
Pojawia się w:
Inżynieria Bezpieczeństwa Obiektów Antropogenicznych
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics of stress distribution of a multi layered cylindrical pressure vessel
Autorzy:
Somadder, Somnath
Das, Palash
Islam, Md. Ashraful
Powiązania:
https://bibliotekanauki.pl/articles/2201648.pdf
Data publikacji:
2022
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
stress distribution
thermo-mechanical load
multi-layer pressure vessels
centripetal
centrifugal
analytical analysis
numerical analysis
rozkład naprężeń
obciążenie termomechaniczne
wielowarstwowe naczynia ciśnieniowe
analiza analityczna
analiza numeryczna
Opis:
The operation of a multilayer pressure vessel subjected to thermomechanical loads is very significant. The cylindrical pressure vessel is widely used in industrial engineering: for example, to hold a variety of different types of liquid. On thick-walled cylinders, various loading circumstances such as internal overpressure, external overpressure, heat, bending, twisting, and combinations of these load characteristics are applied. Researchers have developed a number of strategies for enhancing the strength of cylinders, including the use of multilayer cylinders and increasing the thickness of the walls. This paper presents the results of an analytical and numerical analysis of a three-layer cylinder. The Abaqus FEA software is used to determine temperature, displacement, and stress distribution of a multilayer cylinder considering the effect of centripetal and centrifugal heat flow. From the numerical analysis, it is observed that centrifugal heat flux is more hazardous than centripetal heat flux for a multi-layered cylinder under thermo-mechanical loading.
Źródło:
Journal of Mechanical and Energy Engineering; 2022, 6, 2; 1--6
2544-0780
2544-1671
Pojawia się w:
Journal of Mechanical and Energy Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of operation in piston–con–rod system of ship propulsion engine on the basis of harmonic torque
Autorzy:
Rosłanowski, J.
Charchalis, A.
Powiązania:
https://bibliotekanauki.pl/articles/247247.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
criteria of mechanical and thermal load of the engine
tribological criteria of piston-crank combustion
engine system
Opis:
The following article includes the analysis of mechanical and thermal load criteria of combustion engine. Those criteria have been divided into tribological, technical in detail and technical in general. The above criteria have been related to piston-con-rod system, in which, two tribological centres were specified. One centre included, piston-piston rings and cylinder, in which, piston rings serve as labyrinth seal and the cylinder constitutes piston guides. Crank bearings and main bearings of engine crankshaft constitute the second centre. From the point of tribological view, piston-piston rings and cylinder constitute slide and thrust bearing lubricated hydrodynamically, while crankshaft bearings a-c-t as slide and journal bearings also lubricated hydrodynamically. In the description of thermal load of the above-mentioned tribological centres, special attention was paid to criteria that ensure their motion reliability and durability of engine operation. Whereas in the description of mechanical load of elements constituting investigated centres, some criteria were determined resulting from their functionality and fatigue strength of the material they were made of. Criteria of thermal loads were based on mean density flux of heat conducted through the walls of engine elements, paying attention to their low precision of evaluation. It has been emphasized that synthetic criteria indicators are the most precise. They are determined on the basis of engine load measurements during its operation. Those criteria allow us to describe the operating process of con-rod-piston diesel engines and at the same time it is possible to expose their technical condition which is of essential practical meaning. The wear process of tribological centres that takes place during operating in piston-con-rod system, affects the course of engine working process and its techno-economic indicators.
Źródło:
Journal of KONES; 2013, 20, 4; 390-395
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Material consumption criteria of piston – con – rod elements system of combustion engine
Autorzy:
Rosłanowski, J.
Charchalis, A.
Powiązania:
https://bibliotekanauki.pl/articles/246321.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
criteria of mechanical and thermal load of the engine
tribological criteria of piston-crank combustion
engine system
Opis:
The following article includes the analysis of mechanical and thermal load criteria of combustion engine. Those criteria have been divided into tribological, technical in detail and technical in general. The above criteria have been related to piston-con-rod system, in which, two tribological centres were specified. One centre included, piston-piston rings and cylinder, in which, piston rings serve as labyrinth seal and the cylinder constitutes piston guides. Crank bearings and main bearings of engine crankshaft constitute the second centre. From the point of tribological view, piston-piston rings and cylinder constitute slide and thrust bearing lubricated hydrodynamically, while crankshaft bearings a-c-t as slide and journal bearings also lubricated hydrodynamically. In the description of thermal load of the above-mentioned tribological centres, special attention was paid to criteria that ensure their motion reliability and durability of engine operation. Whereas in the description of mechanical load of elements constituting investigated centres, some criteria were determined resulting from their functionality and fatigue strength of the material they were made of. Criteria of thermal loads were based on mean density flux of heat conducted through the walls of engine elements, paying attention to their low precision of evaluation. It has been emphasized that synthetic criteria indicators are the most precise. They are determined on the basis of engine load measurements during its operation. Those criteria allow us to describe the operating process of con-rod-piston diesel engines and at the same time it is possible to expose their technical condition which is of essential practical meaning. The wear process of tribological centres that takes place during operating in piston-con-rod system, affects the course of engine working process and its techno-economic indicators.
Źródło:
Journal of KONES; 2013, 20, 4; 397-403
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zastosowanie mikroskopu skaningowego do analizy uszkodzeń wewnątrzmateriałowych w betonach konstrukcyjnych
Using methods of scanning microscopy to analyse images of the internal structure of damaged concretes
Autorzy:
Golewski, G. L.
Powiązania:
https://bibliotekanauki.pl/articles/162579.pdf
Data publikacji:
2009
Wydawca:
Polski Związek Inżynierów i Techników Budownictwa
Tematy:
beton konstrukcyjny
uszkodzenie materiałowe
obciążenie mechaniczne
rysa
metoda badań
mikroskop skaningowy
zasada działania
analiza obrazu
structural concrete
material damage
mechanical load
crack
test method
scanning electron microscopy
principle of operation
image analysis
Opis:
Prezentowany artykuł dotyczy możliwości wykorzystania metod mikroskopii skaningowej do analizy obrazów wewnętrznej struktury betonów po ich zniszczeniu. W części teoretycznej przedstawiono budowę mikroskopu skaningowego wraz z jego schematem blokowym, oraz opisano specyfikę zastosowania podstawowych detektorów elektronowych. Szczególną uwagę zwrócono na wymagania, jakie muszą spełniać próbki wykorzystywane do takich badań. Część praktyczna dysertacji przedstawia analizę podstawowych uszkodzeń w betonie, tj. szczelin prostych i skrzydłowych. Pokazano zdjęcia skaningowe takich defektów wraz z ich schematami i opisem teoretycznym. Jako możliwości modyfikacji struktury kompozytów betonowych, pod kątem ograniczenia powstawania w nich defektów, przytoczono nowoczesne metody nanotechnologii.
This paper concerns the possibility of using methods of scanning microscopy to analyse images of the internal structure of damaged concretes. A theoretical section concerns the structure and functional scheme of the scanning microscope, and describes the specifics of the use of basic electron detectors. Particular attention is paid to the requirements which need to be met by the samples used in such investigations. The practical section of the paper contains an analysis of the principal types of damage to concrete, namely simple cracks and wing cracks. Scanning photographs of such defects are shown, together with diagrams and a theoretical description. Modern methods of nanotechnology are proposed as ways of modifying the structure of concrete composites to limit the occurrence of defects.
Źródło:
Przegląd Budowlany; 2009, R. 80, nr 7-8, 7-8; 64-68
0033-2038
Pojawia się w:
Przegląd Budowlany
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of grain properties on loads in model silo
Autorzy:
Molenda, M.
Horabik, J.
Thompson, S.A.
Ross, I.J.
Powiązania:
https://bibliotekanauki.pl/articles/24062.pdf
Data publikacji:
2004
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
silo
grain property
grain
mechanical property
load
Źródło:
International Agrophysics; 2004, 18, 4
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of load transfer into composite structure
Autorzy:
Szymczyk, E.
Jachimowicz, J.
Puchała, K.
Powiązania:
https://bibliotekanauki.pl/articles/118025.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Promocji Wiedzy
Tematy:
mechanical joint
adhesive joint
composite material
load transfer
FEA
Opis:
The paper presents advantages and disadvantages of metal foils insertion between composite layers. Composites are complex materials of aniso-tropic structure leading to various failure mechanisms. Mechanism of compressive load transfer into composite laminates by shear of the matrix is analysed. The method of improvement compressive strength of laminates is presented according to literature and analysed for a sele-cted case. Simplified models of a laminate structure modified using various metal foils configurations are analysed with MSC.Marc code. Axial stress in prepreg layers and shear stress in adhesive layers are studied.
Źródło:
Applied Computer Science; 2014, 10, 3; 86-94
1895-3735
Pojawia się w:
Applied Computer Science
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies