Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "coating deposition" wg kryterium: Temat


Tytuł:
Application of Al2O3, ZnO, and TiO2 ALD thin films as antireflection coating in the silicon solar cells
Autorzy:
Szindler, Marek
Szindler, Magdalena
Powiązania:
https://bibliotekanauki.pl/articles/27315697.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Stowarzyszenie Elektryków Polskich
Tematy:
optical thin film
antireflection coating
atomic layer deposition
solar cells
Opis:
The article describes the results of a research on the surface morphology and optical properties of Al₂O₃, ZnO, and TiO₂ thin films deposited by atomic layer deposition (ALD) for applications in silicon solar cells. The surface topography and elemental composition were characterised using a scanning electron microscope, and thickness was determined using an optical reflectometer. The samples were structurally examined using a Raman spectrometer. The structural variant was identified: for Al₂O₃ it is sapphire, for TiO₂ it is anatase, and for ZnO it is wurtzite. Possibilities of minimising light reflection using single and double thin film systems below 5% were presented. For the first time, the effectiveness of these thin films on the current-voltage characteristics and electrical parameters of manufactured silicon solar cells was examined and compared. The solar cell with the highest efficiency of converting solar radiation into electricity was obtained for Al₂O₃/TiO₂ and the efficiency of such a photovoltaic device was 18.74%.
Źródło:
Opto-Electronics Review; 2023, 31, 4; art. no. e148223
1230-3402
Pojawia się w:
Opto-Electronics Review
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Cavitation erosion resistance of Ni-Co based coatings
Autorzy:
Szala, M.
Hejwowski, T.
Lenart, I
Powiązania:
https://bibliotekanauki.pl/articles/101864.pdf
Data publikacji:
2014
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
cavitation erosion
Ni-Co based coating
PTA deposition
Opis:
The Ni-Co based coatings were performed by means of PTA method from Ni-based and Co-based powders. The cavitation erosion resistance of Ni-Co specimens and reference sample in deionized water was determined by the ultrasonic vibration system. The microstructure, as well as mechanism of cavitation erosion of coating was examined by using SEM and LOM. The main mechanism of erosion is cracking and spalling at the boundary of dendrites and eutectics. Coatings exhibit higher cavitation erosion resistance than the reference sample. Therefore, they could be applied to repair and protect pump elements from cavitation wear.
Źródło:
Advances in Science and Technology. Research Journal; 2014, 8, 21; 36-42
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Cermet ESD coatings modified by laser treatment
Powłoki cermetalowe naniesione elektroiskrowo i modyfikowane obróbka laserowa
Autorzy:
Radek, N.
Konstanty, J.
Powiązania:
https://bibliotekanauki.pl/articles/354248.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
powłoki cermetalowe
obróbka laserowa
właściwości tribologiczne powłok
trybologia
korozja
electro-spark deposition
laser treatment
coating
roughness
tribology
microstructure
corrosion resistance
microhardness
adhesion
Opis:
The main objective of the present work was to determine the influence of laser treatment on microstructure, microhardness, roughness, bonding strength, corrosion resistance and tribological properties of wear resistant coatings produced on C45 carbon steel by the electro-spark deposition (ESD) process. Consumable WC-Co-Al2O3 electrodes were prepared by the powder metallurgy route and transferred to the substrate surface using the EIL-8A apparatus. The cermet layers were subsequently melted by means of the BLS 720 Nd:YAG laser. The coating characterisation studies showed marked improvements in the bonding between the steel substrate and the cermet coating, and in corrosion resistance at the expense of higher surface roughness and minor drop in the Vickers microhardness.
Głównym celem pracy było określenie wpływu obróbki laserowej na mikrostrukturę, mikrotwardość, chropowatość, przyczepność, odporność na korozję i właściwości tribologiczne powłok odpornych na ścieranie naniesionych na stal węglową C45 w wyniku procesu obróbki elektroiskrowej (ESD). Zużywalne elektrody WC-Co-Al2O3 wykonano metodą metalurgii proszków, a materiał nanoszono na powierzchnie podłoża używając urządzenia EIL-8A. Powłoki cermetalowe były następnie przetapiane laserem BLS 720 Nd:YAG. Badania powłok wykazały znaczna poprawę w wiązaniu miedzy stalą a pokryciem cermetalowym, a także poprawę odporności na korozje, ale za cenę wyższej chropowatości powierzchni i niewielkiego zmniejszenia mikrotwardości Vickersa.
Źródło:
Archives of Metallurgy and Materials; 2012, 57, 3; 665-670
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Design concepts of gaseous detonation guns for thermal spraying
Principy konstruirovanija detonacionno-gazovykh ustanovok dlja napylenija pokrytijj
Autorzy:
Kharlamov, Y.
Kharlamov, M.
Powiązania:
https://bibliotekanauki.pl/articles/792142.pdf
Data publikacji:
2013
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
gaseous detonation
structural analysis
coating deposition
thermal spraying
conventional coating techniqu
energy source
oscillatory system
dynamic characteristics
Źródło:
Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2013, 13, 4
1641-7739
Pojawia się w:
Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of heat treatment on the surface morphology and optical properties of the Al2O3 thin film for use in solar cells
Autorzy:
Szindler, Marek
Szindler, Magdalena M.
Powiązania:
https://bibliotekanauki.pl/articles/2063888.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Stowarzyszenie Elektryków Polskich
Tematy:
antireflection coating
atomic layer deposition method
solar cells
Opis:
The technology of manufacturing silicon solar cells is complex and consists of several stages. The final steps in succession are the deposition of antireflection layer and discharge contacts. Metallic contacts are usually deposited by the screen printing method and then, fired at high temperature. Therefore, this article presents the results of a research on the effect of heat treatment on the properties of the Al2O3 thin film previously deposited by the atomic layer deposition method. It works well as both passivating and antireflection coating. Moreover, heat treatment affects the value of the cell short-circuit current and, thus, its efficiency. The surface morphology, optical and electrical properties were investigated, describing the influence of heat treatment on the properties of the deposited layers and the manufactured solar cells.
Źródło:
Opto-Electronics Review; 2021, 29, 4; 181--186
1230-3402
Pojawia się w:
Opto-Electronics Review
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of impulse bias potential to formation of wear-proof coating deposited from plasma fluxes
Autorzy:
Breus, A.
Pavlenko, V.
Powiązania:
https://bibliotekanauki.pl/articles/197392.pdf
Data publikacji:
2016
Wydawca:
Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:
plasma deposition
nanostructured coating
impulse bias
pokrycie plazmowe
powłoka nanostrukturalna
Opis:
Plasma-based technology is used to deposit a wear-proof nanostructured coating on plunger tappets of pump of aviation oil system block, which allows increasing the life of the parts up to 3–5 times. For the nanostructured coatings, which are formed at the impulse bias supply, the electric field strength is 103 -104 times greater than for the microstructured coatings. It results in significant change of activation energy of the process of strong bond formation in the growing coating, which makes it possible to obtain high qualitative characteristics of the coating.
Źródło:
Zeszyty Naukowe. Transport / Politechnika Śląska; 2016, 92; 17-22
0209-3324
2450-1549
Pojawia się w:
Zeszyty Naukowe. Transport / Politechnika Śląska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Electrophoretic Deposition and Characterisation of Chitosan Coatings on Near-Β Titanium Alloy
Autorzy:
Jugowiec, D.
Kot, M.
Moskalewicz, T.
Powiązania:
https://bibliotekanauki.pl/articles/355398.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
chitosan
Ti13Nb13Zr alloy
electrophoretic deposition
coating
Opis:
In this study, chitosan coatings were electrophoretically deposited (EPD) on near-β Ti-13Nb-13Zr alloy. The influence of colloidal solution composition and EPD parameters on the quality of chitosan coatings was investigated. It was established that the uniformity of as-deposited chitosan coatings is highly dependent on the chemical composition of the solution used for EPD, the pH, electrophoretic mobility and zeta potential of chitosan colloidal molecules, as well as EPD parameters, such as potential difference value and deposition time. The microstructure of the coatings was investigated using electron microscopy and X-ray diffractometry. The coatings 350 nm thick were homogeneous and exhibited an amorphous structure. The coatings had low hardness and Young’s modulus. The effect of surface of the substrate preparation prior to coating deposition on the adhesion of chitosan coatings to the Ti-13Nb-13Zr alloy was also investigated. The coatings exhibited good adhesion to the non-acid-etched surface of the titanium alloy.
Źródło:
Archives of Metallurgy and Materials; 2016, 61, 2A; 657-664
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluating the Durability of SiC-Coated Carbon Composites Under Thermal Shock Conditions
Autorzy:
Lee, Ji Eun
Bae, Soo Bin
Cho, Nam Choon
Lee, Hyung Ik
Meng, Zicheng
Lee, Kee Sung
Powiązania:
https://bibliotekanauki.pl/articles/2049309.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
durability
carbon composites
silicon carbide coating
chemical vapor deposition
chemical vapor reaction
Opis:
Oxidation and indentation properties of silicon carbide-coated carbon composites were investigated to analyze its durability under atmospheric thermal shock conditions. The silicon carbide-coated samples were prepared either with chemical vapor deposition or chemical vapor reaction/chemical vapor deposition hybrid coating. The remnant weight of uncoated and coated samples was investigated after each thermal shock cycle. The surface and cross-section of coated samples were then analyzed to confirm morphological changes of the coating layers. The spherical indentation test for uncoated and coated samples were also performed. As a result, silicon carbide coating improved the oxidation resistance, elastic modulus, and hardness of carbon composites. Hybrid coating drastically enhanced the durability of samples at high temperature in atmospheric conditions.
Źródło:
Archives of Metallurgy and Materials; 2021, 66, 3; 777-782
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of TiN Coating Properties Deposited on HS6-5-2C Steel
Ocena właściwości powłoki TiN osadzonej na stali HS6-5-2C
Autorzy:
Kowalczyk, Joanna
Powiązania:
https://bibliotekanauki.pl/articles/1857779.pdf
Data publikacji:
2020
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
TiN coating
DLC coating
Al2O3
physical vapour deposition
PVD
powłoka TiN
powłoka a-C:H
fizyczne osadzanie z fazy gazowej
Opis:
The article presents selected properties of TiN coating on HS6-5-2C steel by Physical Vapour Deposition (PVD). The coating thickness was measured with a Calotest, and its hardness was measured with a nanohardness tester. Tribological parameters were determined, namely, the coefficient of friction and linear wear on the TRB3 tester operating in a ball-on-disk sliding friction pair. The disc was made of HS6-5-2C steel with a TiN coating and the ball of 100Cr6 steel without coating and with a-C:H coating, with Al2O3. The tests were performed under technically dry friction conditions. The coating structure observations were made using a scanning microscope, and the analysis of the geometric structure of samples, before and after tribological tests, were performed with an optical profile measurement gauge. The test results showed that the lowest linear wear was obtained for friction pairs with an Al2O3 ball and a steel ball with a-C:H coating applied.
W artykule przedstawiono wybrane właściwości powłoki TiN osadzonej na stali HS6-5-2C techniką fizycznego osadzania z fazy gazowej PVD. Zmierzono grubość powłoki przy użyciu Calotestera oraz jej twardość za pomocą nanotwardościomierza. Określono parametry tribologiczne, a mianowicie współczynnik tarcia i zużycie liniowe na testerze TRB3 pracującym w skojarzeniu trącym kula–tarcza w ruchu ślizgowym. Tarcza wykonana była ze stali HS6-5-2C z powłoką TiN, a kula ze stali 100Cr6 bez i z naniesioną powłoką a-C:H, z Al2O3. Badania wykonano w warunkach tarcia technicznie suchego. Obserwacje struktury powłoki zrealizowano przy użyciu mikroskopu skaningowego, a analizę struktury geometrycznej powierzchni próbek przed i po testach tribologicznych wykonano profilometrem optycznym. Wyniki badań wskazały, że najmniejsze zużycie liniowe uzyskano dla par trących z kulą wykonaną z Al2O3 oraz stalową z naniesioną powłoką a-C:H.
Źródło:
Tribologia; 2020, 291, 3; 23-31
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of YSZ coatings on nickel-based alloys by anodic electrophoretic deposition
Autorzy:
Binxia, Yuan
Tianzhong, Chen
Yongzhi, Shang
Haibo, Xue
Min, Li
Powiązania:
https://bibliotekanauki.pl/articles/2204142.pdf
Data publikacji:
2023
Wydawca:
Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Tematy:
YSZ coating
anodic electrophoretic deposition
suspension solution
nickel-based alloys
Opis:
In the paper, YSZ coatings were prepared on nickel-based alloy substrates by anodic electrophoretic deposition. The YSZ suspension solution was obtained under stirring and ultrasonic treatment, in which the anhydrous ethanol and acetylacetone were used as the dispersion medium and ammonium polyacrylate was used as the dispersant of the suspension. The effects of different deposition voltage and deposition time on YSZ coating were investigated. Meantime, the microstructure of the coating surface was observed by metallographic microscope. It was found that the high-quality YSZ coating could be obtained by deposition at 60 V for 2–3 min. Finally, the effect of sintering temperature on coating quality was investigated by X-ray diffractometer and scanning electron microscopy. The results showed that the YSZ coating bonded closely with the substrate after sintering at 1200 °C, and the porosity of the YSZ coating increased after sintering.
Źródło:
Polish Journal of Chemical Technology; 2023, 25, 1; 8--11
1509-8117
1899-4741
Pojawia się w:
Polish Journal of Chemical Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Formation of coatings with technologies using concentrated energy stream
Autorzy:
Radek, Norbert
Kalinowski, Artur
Pietraszek, Jacek
Orman, Łukasz J.
Szczepaniak, Marcin
Januszko, Adam
Kamiński, Janusz
Bronček, Jozef
Paraska, Olga
Powiązania:
https://bibliotekanauki.pl/articles/26079553.pdf
Data publikacji:
2022
Wydawca:
Stowarzyszenie Menedżerów Jakości i Produkcji
Tematy:
powłoka elektroiskrowa
obróbka wiązką laserową
powłoka
powierzchnia niejednorodna
lectro-spark deposition
laser beam processing
coating
heterogeneous surface
Opis:
A number of modern surface processing methods use an energy flux. The examples include electro-spark deposition (ESD) and laser beam processing (LBP). The work concerns the study of Cu-Mo coatings deposited on C45 carbon steel, which were then eroded with a laser beam. The analysis included the analysis of the microstructure, measurements of macrogeometry and microhardness, corrosion resistance tests of selected areas after laser treatment. The coatings were applied with ELFA-541 and subjected to Nd:YAG laser treatment with variable laser parameters. The problem presented in the work can be used to extend the knowledge of the areas of application of ESD coatings, especially in sliding friction pairs.
Źródło:
Production Engineering Archives; 2022, 28, 2; 117--122
2353-5156
2353-7779
Pojawia się w:
Production Engineering Archives
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Formation of Cu-Mo anti-wear coatings and their tribological properties before and after laser treatment
Formowanie i właściwości tribologiczne przeciwzużyciowych powłok kompozytowych Cu-Mo przed i po obróbce laserowej
Autorzy:
Radek, N.
Kamiński, J.
Powiązania:
https://bibliotekanauki.pl/articles/188870.pdf
Data publikacji:
2010
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
obróbka elektroiskrowa
obróbka laserowa
powłoka
tribologia
electro-spark deposition
laser treatment
coating
tribology
Opis:
The paper is concered with determining the influence of the laser treatment process on the exploitation properties of electro spark coatings. The properties were assessed after laser treatment by analysising microstructure, measuring the microhardness, friction coefficient and corrosion resistance. The tests were carried out for Mo and Cu coatings (the anode) electro-spark deposited over the C45 steel substrate (the cathode)and molten with a laser beam. The coatings were deposited by means of an ELFA-541. The laser treatment was performed with an Nd:YAG, BLS 720 laser. The coatings, whether laser-treated or not, exhibit very good performance properties and high reliability, and this makes them suitable for use in sliding friction pairs.
W pracy badano wpływ obróbki laserowej na właściwości powłok nanoszonych elektroiskrowo. Ocenę właściwości powłok po obróbce laserowej przeprowadzono na podstawie obserwacji mikrostruktury, pomiarów mikrotwardości i współczynnika tarcia oraz badań odporności korozyjnej. Badania przeprowadzono, wykorzystując Mo oraz Cu jako materiały powłokowe (anody) nakładane elektroiskrowo na próbki ze stali C45 (katody), a następnie przetapiane wiązką laserową. Do nanoszenia powłok elektroiskrowych użyto urządzenia produkcji bułgarskiej, model ELFA-541. Obróbkę laserową nałożonych powłok elektroiskrowych wykonano laserem Nd:YAG, model BLS 720. Powłoki tego typu zarówno przed, jak i po obróbce laserowej mają dobre własności i mogą znaleźć zastosowanie w ślizgowych węzłach tarcia.
Źródło:
Tribologia; 2010, 5; 191-200
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Functional plasma-deposited coatings
Autorzy:
Pashechko, M.
Kindrachuk, M.
Gumeniuk, I.
Tisov, O.
Zahrebelniy, V.
Powiązania:
https://bibliotekanauki.pl/articles/957956.pdf
Data publikacji:
2017
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
plasma deposition
coating
laser treatment
thermal cycling
mass transfer
adhesion
wear resistance
Opis:
The paper focuses on the problem of low adhesion of plasma sprayed coatings to the substrate. The subsequent laser treatment modes and their influence on the coating-substrate interface were studied. This allows to decrease the level of met-stability of the coating, thus decreasing its hardness down to 11–12 GPa on the surface and to about 9 GPa on depth of 400 μm. The redistribution of alloying elements through solid and liquid diffusion improves mechanical properties and rises the adhesion up to 450 MPa after remelting and up to 90–110 MPa after laser-aided thermal cycling. At the same time, remelting of coating helps to decrease its porosity down to 1%. The obtained complex of properties also allows to improve wear resistance of coatings and to decrease friction factor.
Źródło:
Advances in Science and Technology. Research Journal; 2017, 11, 4; 301-304
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High Temperature Oxidation Property of SiC Coating Layer Fabricated by Aerosol Deposition Process
Autorzy:
Ham, G.-S.
Kim, S.-H.
Park, J.-Y.
Lee, K.-A.
Powiązania:
https://bibliotekanauki.pl/articles/352142.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
silicon carbide
aerosol deposition
coating
high temperature oxidation
Opis:
This study investigated the high temperature oxidation property of SiC coated layer fabricated by aerosol deposition process. SiC coated layer could be successfully manufactured by using pure SiC powders and aerosol deposition on the Zr based alloy in an optimal process condition. The thickness of manufactured SiC coated layer was measured about 5 μm, and coating layer represented high density structure. SiC coated layer consisted of α-SiC and β-SiC phases, the same as the initial powder. The initial powder was shown to have been crushed to the extent and was deposited in the form of extremely fine particles. To examine the high temperature oxidation properties, oxidized weight gain was obtained for one hour at 1000°C by using TGA. The SiC coated layer showed superior oxidation resistance property than that of Zr alloy (substrate). The high temperature oxidation mechanism of SiC coated layer on Zr alloy was suggested. And then, the application of aerosol deposited SiC coated layer was also discussed.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1347-1351
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of a Steel Substrate Surface Roughness on the Mechanical Properties of a Peek Coating Deposited with the Electrophoretic Method
Wpływ chropowatości powierzchni podłoża ze stali konstrukcyjnej na właściwości mechaniczne powłoki PEEK osadzonej elektroforetycznie
Autorzy:
Otto, Mateusz
Fiołek, Aleksandra
Zimowski, Sławomir
Powiązania:
https://bibliotekanauki.pl/articles/2134820.pdf
Data publikacji:
2022
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
powłoka
PEEK
właściwości mechaniczne
chropowatość powierzchni podłoża
metoda elektroforezy
coating
mechanical properties
surface roughness of substrate
electrophoretic deposition method
Opis:
The mechanical properties, adhesion and roughness of polymer coatings depend on many factors, including the unevenness of the substrate surface. Nevertheless, the influence of the substrate surface roughness is related to the coating type and substrate material and the used deposition method. Therefore, the effect of the surface roughness of a structural steel substrate on the mechanical properties of a PEEK coating is ambiguous. The indentation tests conducted show that, at a specific load of the indenter, the roughness of the steel substrate surface does not significantly affect the Vicker’s hardness of the tested PEEK coatings. The average Vicker’s hardness and elastic modulus are approximately 300 MPa and 5.6 Gpa, respectively, at the lowest of the applied loads, regardless of the surface roughness level of the steel substrate. Nevertheless, the surface roughness of the steel substrate after fine grinding of Ra = 0.21 μm, compared to the polished one with Ra = 0.005 μm, meant that adhesion improved, and the scratch hardness increased by approximately 130 to 370 [MPa] of the PEEK coating.
Właściwości mechaniczne, przyczepność oraz chropowatość powłok polimerowych zależą od wielu czynników, a w tym od nierówności powierzchni podłoża. Niemniej jednak wpływ wielkości chropowatości powierzchni podłoża okazuje się być związany z rodzajem materiału powłokowego i podłoża oraz zastosowaną metodą osadzania. Wobec tego oddziaływanie chropowatości powierzchni podłoża ze stali konstrukcyjnej na właściwości mechaniczne powłoki PEEK osadzanej elektroforetycznie nie jest jednoznaczny. Przeprowadzone badania indentacyjne wskazują, że przy określonym obciążeniu wgłębnika chropowatość powierzchni stalowego podłoża nie wpływa znacząco na twardość Vickers’a badanych powłok PEEK. Średnia twardość Vickers’a i modułu sprężystości wynosi odpowiednio ok. 300 MPa i 5.6 GPa przy najmniejszym z zastosowanych obciążeń, niezależnie od mikronierówności powierzchni stalowego podłoża. Nie mniej jednak większa chropowatość powierzchni stalowego podłoża po szlifowaniu dokładnym rzędu Ra = 0.21 μm, względem polerowanego o Ra = 0.005 μm, przełożyła się na polepszanie adhezji i spowodowała wzrost twardości zarysowania powłoki PEEK z ok. 130 do 370 [MPa].
Źródło:
Tribologia; 2022, 2; 33--44
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies