Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Si-Al alloy" wg kryterium: Temat


Tytuł:
The Continuous Growth of Bulk Si by Temperature Gradient Zone Melting Method
Autorzy:
Li, Jiayan
Wang, Liang
Hao, Jianjie
Ni, Ping
Tan, Yi
Powiązania:
https://bibliotekanauki.pl/articles/356541.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
bulk Si
TGZM
Si-Al alloy
growth rate
impurities
Opis:
Temperature gradient zone melting (TGZM) method was used to obtain bulk Si continuously for the efficient separation and purification of primary Si from the Si-Al alloy in this work. The effects of alloy thickness, temperature gradient and holding time in TGZM purification technology were investigated. Finally, the continuous growth of bulk Si without eutectic inclusions was obtained. The results showed that the growth rate of bulk Si was independent of the liquid zone thickness. When the temperature gradient was changed from 2.48 K/mm to 3.97 K/mm, the growth rate of bulk Si was enhanced from 7.9×10-5 mm/s to 2.47×10-4 mm/s, which was increased by about 3 times. The bulk Si could grow continuously and the growth rate was decreased with the increase of holding time from 1 h to 5 h. Meanwhile, low refining temperature was beneficial to the removal of impurities. With a precipitation temperature of 1460 K and a temperature gradient of 2.48 K/mm, the removal rates of Fe, P and B were 99.8%, 94.0% and 63.6%, respectively.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 1; 271-278
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Correlation of Hardness and Silicon Morphology for Al-Si-Sb Alloy
Autorzy:
Uzun, O.
Yilmaz, F.
Emeksiz, C.
Ergen, S.
Kolemen, U.
Powiązania:
https://bibliotekanauki.pl/articles/356738.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Al-Si alloy
casting
Vickers
finite element analysis
Opis:
In this study, we have focused on the role of silicon morphology on the hardness of eutectic Al–12 wt.% Si–0.5 wt.% Sb alloy solidified at different cooling rates. The alloys were produced by using induction melting, arc-remelting and melt-spinning techniques. The cooling rates of the alloys were determined as 0.5, 60 and ~105°C.s-1 for induction-melted, arc-remelted and meltspun alloy. The experimental results show that as the cooling rate increased the coarse silicon phase was substantially refined and its morphology altered from sharp need-like to round shape. Two exothermic peaks, attributed to precipitation and coarsening of silicon from supersaturated α-Al, were observed in the DSC curve of MS alloy. Vicker’s hardness of melt-spun alloy was found two times higher than those of IMed and ARed alloys. The lowest hardness of induction-melted alloy was ascribed to the lamellar morphology of silicon, yielding decohesive rupture. This result was confirmed by finite element analyzing.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 1; 467-472
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect of Modifier on the Microstructure of the AlSi10CuNiMn Alloy
Autorzy:
Cais, Jaromir
Heinrich, Jiri
Jirounkova, Klara
Powiązania:
https://bibliotekanauki.pl/articles/103309.pdf
Data publikacji:
2020
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
Al-Si alloy
microstructure
modification
microscopy
stop Al-Si
mikrostruktura
modyfikacja
mikroskopia
Opis:
This paper deals with different types of modifiers and their effect on the microstructure of the Al-Si alloy. For the purposes of this research, strontium, antimony and calcium were used as the modifiers of the AlSi10CuNiMn alloy. Unmodified alloy was cast in order to be compared with the alloy modified by different modifiers in various concentrations. The results of this research were analysed via light and electron microscopy.
Źródło:
Advances in Science and Technology. Research Journal; 2020, 14, 2; 13-18
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Metallurgical Processing of Al-Si Alloys with Increased Iron Content Using Sodium, Strontium, and Tellurium
Autorzy:
Pokusová, M.
Berta, I.
Murgašová, M.
Powiązania:
https://bibliotekanauki.pl/articles/106931.pdf
Data publikacji:
2018
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
Al-Si alloy
iron
metallurgical processing
sodium
tellurium
strontium
Opis:
This paper presents the results of research focused on the processing of the hypoeutectic Al-Si alloy with an increased iron content of 1.75 wt.%. The physical-metallurgical method was used to eliminate the undesirable effect of the iron rich b-phase on the mechanical properties of the casting material using liquid metal modification by strontium, sodium, and tellurium. The chemical composition of an experimental material didn’t contain any elements for the solid-solution strengthening of a matrix; therefore, the presented results can document the capabilities of modifying the b-phase under a minimum influence on the properties of the basic Al-Si system.
Źródło:
Journal of Casting & Materials Engineering; 2018, 2, 1; 9-13
2543-9901
Pojawia się w:
Journal of Casting & Materials Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Crystallization of the AlSi9 Alloy Designed for the Alfin Processing of Ring Supports in Engine Pistons
Autorzy:
Piatkowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/947636.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Al-Si cast alloy
alfin processing
crystallization
microstructure alloys
Opis:
This article presents a study of the crystallization and microstructure of the AlSi9 alloy (EN AC-AlSi9) used for the alfin processing of iron ring supports in castings of silumin pistons. Alfin processing in brief is based on submerging an iron casting in an Al-Si bath, maintaining it there for a defined time period, placing it in a chill mould casting machine and immersing it in the alloy. This technology is used for iron ring supports in the pistons of internal combustion engines, among others. Thermal analysis shows that when the AlSi9 alloy contains a minimal content of iron, nucleation and increase in the triple α (Al)+Fe+(Si) eutectic containing the α -Al8Fe2Si phase takes place at the end of the crystallization of the double α (Al)+ß(Si) eutectic. Due to the morphology of the ”Chinese script” the -Al8Fe2Si phase is beneficial and does not reduce the alloy’s brittleness. After approx. 5 hours of alfin processing, the -Al5FeSi phase crystallizes as a component of the α+Al5FeSi+(Si) eutectic. Its disadvantageous morphology is ”platelike” with sharp corners, and in a microsection of the surface, ”needles” with pointed corners are visible, with increases the fragility of the AlSi9 alloys.
Źródło:
Archives of Foundry Engineering; 2020, 20, 2; 65-70
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modeling of Eutectic Formation in Al-Si Alloy Using A Phase-Field Method
Autorzy:
Ebrahimi, Z.
Powiązania:
https://bibliotekanauki.pl/articles/353792.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
phase-field model
Al-Si alloy
eutectic growth
fluctuations
Opis:
We have utilized a phase-field model to investigate the evolution of eutectic silicon in Al-Si alloy. The interfacial fluctuations are included into a phase-field model of two-phase solidification, as stochastic noise terms and their dominant role in eutectic silicon formation is discussed. We have observed that silicon spherical particles nucleate on the foundation of primary aluminum phase and their nucleation continues on concentric rings, through the Al matrix. The nucleation of silicon particles is attributed to the inclusion of fluctuations into the phase-field equations. The simulation results have shown needle-like, fish-bone like and flakes of silicon phase by adjusting the noise coefficients to larger values. Moreover, the role of primary Al phase on nucleation of silicon particles in Al-Si alloy is elaborated. We have found that the addition of fluctuations plays the role of modifiers in our simulations and is essential for phase-field modeling of eutectic growth in Al-Si system. The simulated finger-like Al phases and spherical Si particles are very similar to those of experimental eutectic growth in modified Al-Si alloy.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 4; 1969-1981
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Semisolid and Strontium Addition on Dry Sliding Wear Behavior of Hypoeutectic Al-Si Alloy
Autorzy:
Anas, Noraz Man
Zakaria, S. A.
Anasyida, A. S.
Mohamad, Hasmaliza
Dhindaw, Brij Kumar
Powiązania:
https://bibliotekanauki.pl/articles/2203750.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hypoeutectic Al-Si alloy
semisolid
cooling slope
Sr
wear resistance
Opis:
The study aims to investigate the effect of semisolid structure and strontium (Sr) addition on the wear behavior of hypoeutectic Al-Si alloy. Semisolid hypoeutectic Al-Si alloy was prepared using cooling slope casting with addition of 0 to 0.93 wt.% Sr. Microstructural study was done using an optical microscope. Vicker microhardness and pin on disc tribometer were used for microhardness and wear testing. When compared to conventional casting, the microhardness of the semisolid hypoeutectic Al-Si alloy improved by 9.8%. Sr addition at 0.43 wt.% resulted in a refined eutectic structure with a 17% increase in hardness over conventional casting. The globular structure α-Al formed during semisolid casting reduced porosity, and the addition of Sr refined the eutectic silicon into a fine fibrous structure that is tightly bound with the Al matrix. These are the primary factors that contribute to the high wear resistance in modified-Sr semisolid alloys.
Źródło:
Archives of Metallurgy and Materials; 2023, 68, 1; 307--317
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Computer-aided analysis of a new process for flanging hollow parts
Autorzy:
Winiarski, G.
Powiązania:
https://bibliotekanauki.pl/articles/118231.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Promocji Wiedzy
Tematy:
flanging
hollow parts
Al-Mg-Si alloy
FEM
Opis:
The paper presents a new process for flanging hollow parts. This process is performed using a specially designed set of tools with movable sleeves. The principle of operation of the tool set is described and examples of the numerical analysis results are given. The FEM simulation was performed on the assumption that the hot-formed hollow workpiece (tube) is made of AlMgSi aluminum alloy. The obtained FEM results show changes in the workpiece shape during flanging, variations in the forming force and the damage function distribution computed according to the C-L failure criterion. The theoretical results of the new flanging method provided basis for experimental tests.
Źródło:
Applied Computer Science; 2014, 10, 1; 19-29
1895-3735
Pojawia się w:
Applied Computer Science
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modifications ALSI7MG0.3 alloys trough CA, SR and SB
Autorzy:
Cais, Jaromír
Lysoňková, Irena
Kraus, Pavel
Powiązania:
https://bibliotekanauki.pl/articles/102369.pdf
Data publikacji:
2018
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
Al-Si alloy
modifier
microstructure
EDX analysis
stop Al-Si
modyfikator
mikrostruktura
analiza EDX
Opis:
This article deals with examing the effect of modifier on changes in microstructure of the alloy AlSi7Mg0.3. The content of the experiment was to examine the effect of addition of calcium, stroncium, and antimony to change the morphology of the eutectic silicon in the alloy type of Al-Si (namely AlSi7Mg0.3). Besides changes in the morphology of eutectic silicon was explored focused on character exlusion modifiers within microstructure of the modified alloy. Examination of the microstructure was realized by scanning electron microscopy and complemented by EDX analysis of the examined samples.
Źródło:
Advances in Science and Technology. Research Journal; 2018, 12, 2; 180-187
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study of Bending Fatigue Properties of Al-Si Cast Alloy
Autorzy:
Tillová, E.
Závodská, D.
Kuchariková, L.
Chalupová, M.
Belan, J.
Powiązania:
https://bibliotekanauki.pl/articles/355910.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
secondary Al-Si cast alloy
fatigue properties
fracture
cast defects
Opis:
Fatigue properties of casting Al-alloys are very sensitive to the microstructural features of the alloy (e.g. size and morphology of the eutectic Si, secondary dendrite arm spacing – SDAS, intermetallics, grain size) and casting defects (porosity and oxides). Experimental study of bending fatigue properties of secondary cast alloys have shown that: fatigue tests up to 106-107cycles show mean fatigue limits of approx. 30-49 MPa (AlSi9Cu3 alloy – as cast state), approx. 65-76 MPa (AlSi9Cu3 alloy after solution treatment) and 60-70 MPa (self-hardened AlZn10Si8Mg alloy) in the tested casting condition; whenever large pore is present at or near the specimen’s surface, it will be the dominant cause of fatigue crack initiation; in the absence of large casting defects, the influence of microstructural features (Si morphology; Fe-rich phases) on the fatigue performance becomes more pronounced.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 3; 1591-1596
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies