Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Buck-Converter" wg kryterium: Temat


Tytuł:
The DC-side active filter with dual-buck full-bridge inverter for wind generators
Autorzy:
Chen, X-Q.
Zhao, S-W.
Wang, Y.
Powiązania:
https://bibliotekanauki.pl/articles/141358.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
multi-pulse ac-dc converter
auto-transformer
harmonic suppression
DC-side active filter
dual-buck full-bridge inverter
Opis:
This paper proposes a new dc-side active filter for wind generators that combines 12-pulse polygon auto-transformer rectifier with dc-side current injection method and dual-buck full-bridge inverter having not the “shoot-through” problem in conventional bridge-type inverters, and therefore this system with the character low harmonic distortion and high reliability. The proposed dc-side active filter is realized by using dual-buck full bridge converter, which directly injects compensation current at dc-side of two six-pulse diode bridges rectifiers. Compared with the conventional three-phase active power filter at ac-side, the system with the dc-side active filter draws nearly sinusoidal current by shaping the diode bridges output current to be triangular without using the instantaneous reactive power compensation technology, only using simple hysteretic current control, even though under load variation and unbalanced voltage disturbances, and while an acceptable linear approximation to the accurate waveform of injection current is recommended. The performance of the system was simulated using MATLAB/Simulink, and the possibility of the dc-side active filter eliminating current harmonics was confirmed in steady and transient states. The simulation results indicate, the system has a total harmonic distortion of current reduced closely to 1%, and a high power factor on the wind generator side.
Źródło:
Archives of Electrical Engineering; 2018, 67, 2; 263--277
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study of Single Sensor Based Maximum Power Point Tracking Techniques for Solar Water Pumping System
Autorzy:
Daoud, A.
Midoun, A.
Powiązania:
https://bibliotekanauki.pl/articles/262773.pdf
Data publikacji:
2009
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie
Tematy:
MPP
buck converter
microcontroller
motor-pump
tachometer
pressure sensor
Opis:
This paper describes new techniques of maximum power point (MPP) tracking for solar water pumping system. The latter system consists of a PV array, a DC/DC buck converter and a universal motor coupled to a centrifugal pump. A conventional hill climbing method is employed to seek the MPP using the motor-pump rotation speed or the pump outlet pressure information. Experimental results are presented and a comparison with conventional algorithm which requires both voltage and current sensors is provided.
Źródło:
Electrical Power Quality and Utilisation. Journal; 2009, 15, 2; 23-27
1896-4672
Pojawia się w:
Electrical Power Quality and Utilisation. Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Small-signal transmittances of DC-DC step-down PWM converter in various operation modes
Autorzy:
Janke, W.
Powiązania:
https://bibliotekanauki.pl/articles/141483.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
step-down converter
BUCK
CCM
DCM
averaged model
small-signal
transmittance
switch-averaging
separation of variables
Opis:
Small-signal transmittances: input-to-output and control-to-output of BUCK converter power stage working in CCM or DCM mode are discussed. Ideal converter case and converter with parasitic resistances are considered separately. Derivations of small-signal transmittances, based on different approaches to finding the converter averaged models, are presented and the results are compared. Apart from theoretical considerations, some results of numerical calculations are presented.
Źródło:
Archives of Electrical Engineering; 2015, 64, 3; 505-529
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Small-signal input characteristics of step-down and step-up converters in various conduction modes
Autorzy:
Janke, W.
Walczak, M.
Powiązania:
https://bibliotekanauki.pl/articles/200514.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
pulse converter
BUCK
BOOST
small-signal models
input characteristics
przetwornica impulsowa
charakterystyki wejściowe
Opis:
Small-signal input characteristics of BUCK and BOOST DC-DC power converters in continuous conduction and discontinuous conduction mode have been presented. Special attention is paid to characteristics in discontinuous conduction mode. The input characteristics are derived from the general form of averaged models of converters. The frequency dependence of input admittance and other input characteristics has been observed in a relatively low-frequency range. The analytical formulas derived in the paper are illustrated by numerical calculations and verified by experiments with a laboratory model of BOOST converter. A satisfying level of conformity of calculations and measurements has been obtained.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2016, 64, 2; 265-270
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Robust Back-stepping Based Higher Order Sliding Mode Control of Non-Inverted Buck-Boost Converter for a Photovoltaic System
Autorzy:
Ullah, Shaukat
Powiązania:
https://bibliotekanauki.pl/articles/1955975.pdf
Data publikacji:
2021
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
MPPT
buck-boost converter
non-linear control
backstepping
higher order sliding
photovoltaic PV
Opis:
Photovoltaic (PV) system generates renewable energy from sunlight, which has low efficiency due to the variance in nature of temperature and irradiance in a fast changing environment condition. Different researchers have proposed different maximum power point tracking MPPT techniques to improve the efficiency. However, still there are many open issues. Thus, to address this, a non-linear back-stepping-based higher order sliding mode controller (BHOSMC) is proposed to harvest maximum power from PV system. The PV module and load is interfaced by a non-inverted buck-boost converter (NIBBC). A linear interpolation method is used for voltage generation and Lyapunov stability is used to verify the control system equation. MATLAB/Simulink software is used for testing the proposed controller performance. The experimental result verified that the proposed BHOSMC is robust, accurate and fast tracking, faultless and less chattering as compared to perturb and observe (P&O), back-stepping control (BSC) and back-stepping-based sliding mode control under rapidly varying meteorological condition.
Źródło:
Power Electronics and Drives; 2021, 6, 41; 113-127
2451-0262
2543-4292
Pojawia się w:
Power Electronics and Drives
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Przetwornica Buck sterowana metodą napięciową - dobór transmitancji analogowego układu sterowania
Autorzy:
Kaczmarek, J.
Powiązania:
https://bibliotekanauki.pl/articles/118572.pdf
Data publikacji:
2016
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
Buck
metoda napięciowa
obciążenie przetwornicy
analogowy układ sterowania
sprzężenie zwrotne
voltage mode
load converter
analog control circuit
feedback
Opis:
W pracy przedstawiono sposób kształtowania analogowej transmitancji układu sterowania HS dla przetwornicy Buck sterowanej metodą napięciową w trybie CCM (Continuous Conduction Mode). Proponowany sposób kształtowania transmitancji HS zapewnia skuteczne tłumienie wpływu zmiany obciążenia przetwornicy na napięcie wyjściowe przetwornicy. Dobór parametrów transmitancji HS oraz badanie stabilności układu z zamkniętą pętlą sprzężenia zwrotnego przeprowadzono w dziedzinie częstotliwości za pomocą wykresów Bodego. Na wybranych przykładach pokazano wpływ rozmieszczenia zer i biegunów funkcji transmitancji HS na pracę przetwornicy.
The article presents a method of shaping the transfer function HS of the analog control circuit for Buck converter in voltage control mode. Buck converter is operating in continuous conduction mode. The proposed method of shaping HS provides an effective damping of load changes to the output voltage of the Buck converter. Parameters of HS transmittance were chosen in frequency domain using Bode diagrams. Stability of close loop system was tested by using Bode diagrams of open loop transmittance.
Źródło:
Zeszyty Naukowe Wydziału Elektroniki i Informatyki Politechniki Koszalińskiej; 2016, 10; 95-118
1897-7421
Pojawia się w:
Zeszyty Naukowe Wydziału Elektroniki i Informatyki Politechniki Koszalińskiej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impact of inductor current ringing in DCM on output voltage of DC-DC buck power converters
Autorzy:
Walczak, M.
Powiązania:
https://bibliotekanauki.pl/articles/141175.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
inductor current ringing
DCM
BUCK converter
parasitic capacitance
electromagnetic compatibility in DC-DC converters
Opis:
Ringing of an inductor current occurs in a DC-DC BUCK converter working in DCM when current falls to zero. The oscillations are the source of interferences and can have a significant influence on output voltage. This paper discusses the influence of the inductor current ringing on output voltage. It is proved through examples that the oscillations can change actual value of duty a cycle in a way that makes the output voltage difficult to predict.
Źródło:
Archives of Electrical Engineering; 2017, 66, 2; 313-323
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Extended Feedback Linearisation Control of Non-ideal DCDC Buck Converter in Continuous-conduction Mode
Autorzy:
Csizmadia, Miklos
Kuczmann, Miklos
Powiązania:
https://bibliotekanauki.pl/articles/2175943.pdf
Data publikacji:
2022
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
DC-DC buck converter
feedback linearisation
inrush current
parasitics
Ackermann
Opis:
This paper presents an extended form of Feedback Linearisation Control (FBLC), which is tested in a non-ideal buck converter in Continuous-conduction Mode (CCM). The FBLC is often used in power electronics to control a non-linear system, due to its advantageous properties. The application of the error integrator shows better steady-state and transient properties, such as a decrease of inrush current. The linearised system has been controlled by the pole placement and the technique is illustrated through an example and simulated via Matlab. The results have been compared by using a classical PID controller, allowing the benefits of FBLC to be highlighted.
Źródło:
Power Electronics and Drives; 2022, 7, 42; 1--8
2451-0262
2543-4292
Pojawia się w:
Power Electronics and Drives
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of gate drive circuit effect in cascode GaN-based applications
Autorzy:
Tan, Q. Y.
Narayanan, E. M. S.
Powiązania:
https://bibliotekanauki.pl/articles/2173545.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
cascode GaNFETs
parasitics
buck converter
gate drive design
kaskoda GaNFETs
przetwornica
pasożytnictwo
projekt napędu bramy
Opis:
This work evaluates the influence of gate drive circuitry to cascode GaN device’s switching waveforms. This is done by comparing three PCBs using three double-pulse-test (DPT) with different gate driving loop design. Among important parasitic elements, source-side inductance shows a significant impact to gate-source voltage waveform. A simulation model based on experimental measurement of the cascode GaNFET used in this work is modified by author. The simulation model is implemented in a synchronous buck converter topology and hereby to assess the impact of gate driving loop of cascode GaN device in both continuous conduction mode (CCM) and critical conduction mode (CRM). Apart from simulation, a synchronous buck converter prototype is presented for experimental evaluation, which shows a 99.15% efficiency at 5A under soft-switching operation (CRM) with a 59ns dead-time.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2021, 69, 2; art. no. e136742
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of gate drive circuit effect in cascode GaN-based applications
Autorzy:
Tan, Q. Y.
Narayanan, E. M. S.
Powiązania:
https://bibliotekanauki.pl/articles/2128152.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
cascode GaNFETs
parasitics
buck converter
gate drive design
kaskoda GaNFETs
przetwornica
pasożytnictwo
projekt napędu bramy
Opis:
This work evaluates the influence of gate drive circuitry to cascode GaN device’s switching waveforms. This is done by comparing three PCBs using three double-pulse-test (DPT) with different gate driving loop design. Among important parasitic elements, source-side inductance shows a significant impact to gate-source voltage waveform. A simulation model based on experimental measurement of the cascode GaNFET used in this work is modified by author. The simulation model is implemented in a synchronous buck converter topology and hereby to assess the impact of gate driving loop of cascode GaN device in both continuous conduction mode (CCM) and critical conduction mode (CRM). Apart from simulation, a synchronous buck converter prototype is presented for experimental evaluation, which shows a 99.15% efficiency at 5A under soft-switching operation (CRM) with a 59ns dead-time.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2021, 69, 2; e136742, 1--7
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Equivalent circuits for averaged description of DC-DC switch-mode power converters based on separation of variables approach
Autorzy:
Janke, W.
Powiązania:
https://bibliotekanauki.pl/articles/200524.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
switch-mode power converter
BUCK
BOOST
averaged models
equivalent circuits
Opis:
Large-signal and small-signal averaged models of basic switch-mode DC-DC power converters: BUCK (step-down) and BOOST (step-up) are presented. Models are derived with the separation of variables approach and have the form of equivalent circuits, suitable for a circuit simulation. Apart from equivalent circuits, small-signal transmittances of converters for CCM and DCM modes are discussed. Parasitic resistances of all components of converters are taken into account. A few examples of simulations and measurement results of selected converter characteristics are also presented. It is shown, that neglecting parasitic resistances (often met in works of other authors) may lead to serious errors in an averaged description of converters.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2013, 61, 3; 711-723
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Designing optimal solar water pumping stations for irrigation of agricultural lands
Autorzy:
Haase, Gundolf
Kirakossian, Gagik T.
Kirakossyan, Gagik H.
Mkrtchyan, Vazgen A.
Powiązania:
https://bibliotekanauki.pl/articles/36071332.pdf
Data publikacji:
2023
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
solar panel
optimization system
buck converter
FLC
engineering model
fill factor
Opis:
An investigation into the design of a stand-alone solar water pumping station for supplying rural areas is presented. It includes a study of system components and their modeling. The solar water pumping station comprises a solar panel, DC/DC buck converter, DC motor driving a centrifugal pump, and a reservoir. The fuzzy-based maximum power point tracker is developed to optimize the drive speed and the water discharge rate of the coupled centrifugal pump. These use dN/I, d(dN/dI) use parameters, and a variation of the fill factor∆α as input variables. The proposed solution is based on a judicious fuzzy adjustment of a converter fill factor, which adapts online the load impedance to the solar panel. The simulation results show the effectiveness of the drive system for both transient and steady-state operations. Hence, it is suitable to use this fuzzy logic procedure as a standard optimization algorithm for such solar water pumping stations. The modeling is carried out in MATLAB/Simulink.
Źródło:
Scientific Review Engineering and Environmental Sciences; 2023, 32, 3; 270-283
1732-9353
Pojawia się w:
Scientific Review Engineering and Environmental Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison of transient states in step-down power converter (BUCK) in continuous and discontinuous conduction mode
Autorzy:
Janke, W.
Walczak, M.
Powiązania:
https://bibliotekanauki.pl/articles/200450.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
step-down converter
BUCK
transient states
CCM
DCM
step-down konwerter
stany przejściowe
Opis:
The object of this paper is a step-down (BUCK) power converter working in the continuous conduction mode (CCM) or discontinuous conduction mode (DCM). Two types of transient states in a converter have been analyzed and observed experimentally: slow transients, described by averaged models of a converter and fast transients, in the course of a single switching period. The averaged models of converter working in CCM, presented in various sources are similar, with some differences concerning only the description of parasitic effects. The averaged models for DCM depend on the adopted modeling method. Models obtained by the switch averaging approach are second-order models (containing two reactive elements in equivalent circuit representation). Models obtained by the separation of variables approach are first-order models. The experimental results given in this paper show the first-order type of transients. Another group of experiments concern fast transients in the course of a single switching period. The oscillations of inductor voltage in the part of a switching period are observed for DCM.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2014, 62, 4; 773-778
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison between thermal simulation results generated by PLECS software and laboratory measurements
Autorzy:
Mysiński, Wojciech
Sysło, Bartłomiej
Powiązania:
https://bibliotekanauki.pl/articles/377458.pdf
Data publikacji:
2019
Wydawca:
Politechnika Poznańska. Wydawnictwo Politechniki Poznańskiej
Tematy:
thermal simulation
PLECS
buck converter
thermal time constant
IGBT
diode
power losses
Opis:
This article deals with the subject of simulation of power losses and thermal processes occurring in semiconductors, as illustrated by an example of a DC/DC buck converter. The simulations were performed in PLECS software. The results obtained from the program were compared with measurement results of a laboratory converter model. The physical model is based on the same components as assumed in the simulation. Similarly, the parameters of the transistor control signal were the same. During operation of the converter, the temperature changes were analyzed using a K-type thermocouple. Based on the obtained results of the temperature measurement in the steady state of the converter operation, the correctness of the simulation carried out in the PLECS program was verified and confirmed.
Źródło:
Poznan University of Technology Academic Journals. Electrical Engineering; 2019, 99; 29-40
1897-0737
Pojawia się w:
Poznan University of Technology Academic Journals. Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparision of Buck-Converter parameters quality depending on coil selection
Autorzy:
Pragłowska-Ryłko, N.
Powiązania:
https://bibliotekanauki.pl/articles/105698.pdf
Data publikacji:
2015
Wydawca:
Centrum Badań i Innowacji Pro-Akademia
Tematy:
Buck-Converter
step-down converter
DC-DC power converter
overvoltage
coil selection
przetwornica Buck
step-down konwerter
przekształtniki DC/DC
przepięcie
Opis:
Buck-Converters belong to DC/DC converters group. One of the main problems during the design stage of DC/DC converter is the proper component selection. The aim of this article is to describe selection of the optimal inductor for the Buck-Converter, enabling to minimize the device output overvoltage, while getting possibly high device efficiency. In order to verify the quality parameters, author made an efficiency comparison of the buck converter, depending on used inductor. Conclusions from this paper allow for optimal selection of coils for the Buck-Converter depending on given criteria.
Źródło:
Acta Innovations; 2015, 17; 22-29
2300-5599
Pojawia się w:
Acta Innovations
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies