Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Manić, G." wg kryterium: Autor


Wyświetlanie 1-2 z 2
Tytuł:
The dose of gamma radiation from building materials and soil
Autorzy:
Manić, G.
Manić, V.
Nikezić, D.
Krstić, D.
Powiązania:
https://bibliotekanauki.pl/articles/147824.pdf
Data publikacji:
2015
Wydawca:
Instytut Chemii i Techniki Jądrowej
Tematy:
natural radioactivity
building materials
soil
dose
Opis:
The radioactivity of some structural building materials, rows, binders, and final construction products, originating from Serbia or imported from other countries, was investigated in the current study by using the standard HPGe gamma spectrometry. The absorbed dose in the air was computed by the method of buildup factors for models of the room with the walls of concrete, gas-concrete, brick and stone. Using the conversion coefficients obtained by interpolation of the International Commission on Radiobiological Protection (ICRP) equivalent doses for isotropic irradiation, the corresponding average indoor effective dose from the radiation of building materials of 0.24 mSv·y−1 was determined. The outdoor dose of 0.047 mSv·y−1 was estimated on the basis of values of the specific absorbed dose rates calculated for the radiation of the series of 238U, 232Th and 40K from the ground and covering materials. The literature values of the effective dose conversion coefficients for ground geometry were applied as well as the published data for content of the radionuclides in the soil.
Źródło:
Nukleonika; 2015, 60, No. 4, part 2; 951-958
0029-5922
1508-5791
Pojawia się w:
Nukleonika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of response surface methodology and fuzzy logic based system for determining metal cutting temperature
Autorzy:
Tanikić, D.
Marinković, V.
Manić, M.
Devedžić, G.
Ranđelović, S.
Powiązania:
https://bibliotekanauki.pl/articles/199818.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
machining
cutting temperature
infrared thermography
response surface methodology
fuzzy logic
obróbka
temperatura cięcia
termografia w podczerwieni
metodologia odpowiedzi powierzchni
logika rozmyta
Opis:
The heat produced in metal cutting process has negative influence on the cutting tool and the machined part in many aspects. This paper deals with measurement of cutting temperature during single-point dry machining of the AISI 4140 steel, using an infrared camera. Various combinations of cutting parameters, i.e. cutting speed, feed rate and depth of cut lead to different values of the measured cutting temperature. Analysis of the measured data should explain the trends in temperature changes depending on changes in the cutting regimes. Furthermore, the temperature data is modelled using response surface methodology and fuzzy logic. The models obtained should determine the influence of cutting regimes on cutting temperature. The main objective is the reduction of cutting temperature, i.e. enabling metal cutting process in optimum conditions.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2016, 64, 2; 435-445
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies