Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

English (EN)·Polski (PL)·Yкраїнський (UK)
Przejdź do strony domowej biblioteki Centralna Biblioteka Wojskowa Link otwiera się w nowym oknie Logo biblioteki Prolib Integro - strona głównaCentralna Biblioteka Wojskowa

Wyszukujesz frazę "Kvapilova, M." wg kryterium: Autor

  Lista filtrów
Wyrównaj
    Wyświetlanie 1-4 z 4
    Tytuł:
    Creep Behavior of a Zirconium Alloy Processed by Equal-Channel Angular Pressing
    Autorzy:
    Sklenicka, V.
    Dvorak, J.
    Kral, P.
    Svoboda, M.
    Kvapilova, M.
    Kopylov, V.
    Nikulin, S.
    Dobatkin, S.
    Powiązania:
    https://bibliotekanauki.pl/articles/1418491.pdf
    Data publikacji:
    2012-09
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    81.40.Lm
    62.20.Hg
    81.05.-t
    81.07.Bc
    81.70.Bt
    Opis:
    A Zr-2.5 wt%Nb alloy was processed by equal-channel angular pressing and then tested under creep conditions at 623 K using a tensile stress within the range from 120 to 300 MPa. The results show conventional power-law creep with a stress exponent of n > 3 which is consistent with an intragranular dislocation process involving the glide and climb of dislocations. It is demonstrated that diffusion creep is not important in these tests. For comparison purposes, the experiments were conducted using both the unprocessed alloy and after processing by equal-channel angular pressing. It was found that under same testing conditions the measured minimum creep rates in the pressed alloy with ultrafine grain sizes were faster than in the same alloy in a coarse-grained unprocessed condition.
    Źródło:
    Acta Physica Polonica A; 2012, 122, 3; 485-489
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Creep Behaviour of a Zr-1 wt% Nb Alloy at Elevated Temperatures
    Autorzy:
    Kvapilová, M.
    Kuchařová, K.
    Kloc, L.
    Sklenička, V.
    Powiązania:
    https://bibliotekanauki.pl/articles/1402075.pdf
    Data publikacji:
    2015-10
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    81.40.Lm
    62.20.Hg
    81.05.-t
    81.70.Bt
    Opis:
    This paper presents experimental data regarding creep behaviour of a Zr-1 wt% Nb alloy at elevated (623 K) and at high temperatures (873-1123 K) corresponding to loss-of-cooling situation of fuel cladding tubes for nuclear reactors. For an elaboration of methodological procedure and comparison purposes, the tensile creep tests were conducted using both constant stress and constant load over a wide range of applied stress. The substantial differences in the acquired creep data between constant stress and constant load creep testing were found especially at high stresses and large creep strain levels.
    Źródło:
    Acta Physica Polonica A; 2015, 128, 4; 548-551
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Influence of Long-term Annealing and Hot Bending on Creep of P92 Pipe
    Autorzy:
    Kral, P.
    Dvorak, J.
    Kvapilova, M.
    Kucharova, K.
    Sklenicka, V.
    Svobodova, M.
    Cmakal, J.
    Powiązania:
    https://bibliotekanauki.pl/articles/1402074.pdf
    Data publikacji:
    2015-10
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    81.05.-t
    81.40.-z
    62.20.Hg
    68.37.Hk
    Opis:
    This work is focused on the creep behaviour of the thick-walled hot bended P92 pipe, with an outer diameter of 350 mm and wall thickness of 39 mm, in its different parts, namely in straight parts and bends. Selected creep specimens machined from axial section of pipe were thermally aged at 650°C to simulate microstructure degradation typical for long-term service conditions. Subsequent tensile creep tests at constant load were performed at 600°C under 140 MPa and creep behaviour of various structure states was compared. Microstructure was investigated by scanning electron microscopy equipped with electron backscatter diffraction. It was found that ageing at 650°C for 10⁴ h caused the significant reduction of creep resistance down to about 10% of initial state and an additional slight reduction of creep resistance after longer ageing for 2×10⁴ h. Further, creep behaviour was significantly influenced by specimen position in the extrados and intrados parts of bends. Microstructure investigation revealed that long-term annealing has negligible effect on high-angle grain boundary spacing and misorientation. By contrast, creep deformation of long-term annealed specimens led to significant decreasing in high-angle grain boundary spacing and caused a change in the misorientation distribution of boundaries.
    Źródło:
    Acta Physica Polonica A; 2015, 128, 4; 543-547
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
    Tytuł:
    Microstructure Mechanisms Governing the Creep Life of Ultrafine-Grained Cu-0.2 wt%Zr Alloy
    Autorzy:
    Kral, P.
    Svoboda, M.
    Dvorak, J.
    Kvapilova, M.
    Sklenicka, V.
    Powiązania:
    https://bibliotekanauki.pl/articles/1418438.pdf
    Data publikacji:
    2012-09
    Wydawca:
    Polska Akademia Nauk. Instytut Fizyki PAN
    Tematy:
    81.05.-t
    61.66.Dk
    62.20.Hg
    68.37.Lp
    Opis:
    Equal-channel angular pressing was conducted at room temperature and extrusion was performed up to 12 passes using route where the billets were rotated by 90° in the same sense between consecutive passes. Tensile creep tests were performed at 473, 573 and 673 K at different constant applied stresses. It was observed that the original coarse grain size of unprocessed alloy was reduced to 0.3 μm after 8 equal-channel angular pressing passes and the grain growth during creep was restricted by precipitates with the mean diameter ≈ 4.0 nm. No significant effect on creep resistance was found after one equal-channel angular pressing pass at 473 and 573 K. However, the longest time to fracture was exhibited by alloy after 2 equal-channel angular pressing passes at 573 and 673 K but with further increasing number of equal-channel angular pressing passes a decrease in the time to fracture was observed. Nevertheless, the beneficial effect of equal-channel angular pressing on creep resistance was still documented after 8 passes for temperatures of 473 and 573 K. By contrast, creep tests performed at 673 K showed that the time to fracture of ultrafine-grained material is shorter as compared with that for as-received state. The 3D laser measurement of surface showed that the creep fracture process is accelerated by formation of vertical surface step relief and cavitation at the intersection of the shear bands during creep.
    Źródło:
    Acta Physica Polonica A; 2012, 122, 3; 457-460
    0587-4246
    1898-794X
    Pojawia się w:
    Acta Physica Polonica A
    Dostawca treści:
    Biblioteka Nauki
    Artykuł
      Wyświetlanie 1-4 z 4

      Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies