Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Kim, H." wg kryterium: Autor


Tytuł:
Fabrication and Raman Studies οf MgO/$SnO_2$ Core-Shell Heteronanowires
Autorzy:
Kim, H.
Powiązania:
https://bibliotekanauki.pl/articles/1807812.pdf
Data publikacji:
2009-07
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.07.-b
78.30.-j
61.05.cp
Opis:
We have reported the fabrication of MgO core/$SnO_2$ shell nanowires, by a two-step evaporation process. Thermal annealing induced changes in morphology, in which the nanowire surface became rough by the agglomeration of $SnO_2$ shell layers and its crystallinity was enhanced. It was found that three fundamental modes (475, 634, 772 $cm^{-1}$) and an infrared (IR)-active mode (682 $cm^{-1}$) of rutile $SnO_2$ appeared in the Raman spectrum of MgO core/$SnO_2$ shell nanowires. By thermal annealing, the relative intensity of the $A_{2u}$ to the $A_{1g}$ line was reduced, presumably due to the disorder or size effects.
Źródło:
Acta Physica Polonica A; 2009, 116, 1; 58-61
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis and Characterization of Si Oxide Coated Nano Ceria by Hydrolysis, and Hydrothermal Treatment at Low Temperature
Autorzy:
Kong, M.
Kim, H. W.
Powiązania:
https://bibliotekanauki.pl/articles/354290.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
nano-particle
water glass
hydro-reaction
coating method
Opis:
The purpose of this work was to the application of Si oxide coatings. This study deals with the preparation of ceria (CeO2) nanoparticles coating with SiO2 by water glass and hydrolysis reaction. First, the low temperature hydro-reactions were carried out at 30~100°C. Second, Silicon oxide-coated Nano compounds were obtained by the catalyzing synthesis. CeO2 Nano-powders have been successfully synthesized by means of the hydrothermal method, in a low temperature range of 100~200°C. In order to investigate the structure and morphology of the Nano-powders, scanning electron microscopy (SEM) and X-ray diffraction (XRD) were employed. The XRD results revealed the amorphous nature of silica nanoparticles. To analyze the quantity and properties of the compounds coated with Si oxide, transmission electron microscopy (TEM) in conjunction with electron dispersive spectroscopy was used. Finally, it is suggested that the simple growth process is more favorable mechanism than the solution/aggregation process.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1125-1129
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and Mechanical Properties of Al-3 Vol% CNT Nanocomposites Processed by High-Pressure Torsion
Autorzy:
Asgharzadeh, H.
Kim, H. S.
Powiązania:
https://bibliotekanauki.pl/articles/354004.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high-pressure torsion
aluminum
CNT
microstructure
mechanical properties
Opis:
Al-3 vol% CNT nanocomposites were processed by high-pressure torsion (HPT) at room temperature under the pressure in the range of 2.5-10 GPa for up to 10 turns. Optical microscopy, scanning electron microscopy, and transmission electron microscopy (TEM) were used to investigate the microstructural evolutions upon HPT. Mechanical properties of the HPT-processed disks were studied using tensile tests and microhardness measurements. The results show gradual evolutions in the density, microstructure, and hardness with increasing the number of turns and applied presure. Nanostructured and elongated Al grains with an average grain thickness of ~40 nm perpendicular to the compression axis of HPT and an aspect ratio of ~3 are formed after 10 turns under 6 GPa. Evaluating the mechanical properties of the 10-turn processed Al/CNT nanocomposites indicates a tensile strength of 321 MPa and a hardness of 122 Hv. The tensile fracture surface of the Al/CNT nanocomposite mostly demonstrates a smooth fracture manner with fine dimples resulting in a low tensile ductility of ~1.5%.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1109-1112
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Molding Condition on Waviness Profile of GFRP Composites in Compression Molding
Autorzy:
Kim, J.
Kim, H.
Lee, D.
Powiązania:
https://bibliotekanauki.pl/articles/1399878.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Lg
81.05.Qk
88.30.mj
Opis:
During compression molding of glass fiber reinforced plastic composites, annealing and quenching experiment is conducted by changing pre-heating and cooling method. As results, major cause of unevenness that affects waviness profile (winding) is the shrinkage of matrix during holding and cooling process. Waviness profile of the surface on molding in glass fiber reinforced plastic composites will be lower when holding pressure load is higher, mold temperature is lower during demolding, and cooling rate is slower. In addition, surface roughness of moldings is depending on holding pressure load compared with mold temperature. According to molding condition of glass fiber reinforced plastic composites, waviness profile of surface can be quantitatively estimated using the proposed equation.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 337-340
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
$SiO_x$ Nanowires Produced on Molybdenum-Coated Si Substrates
Autorzy:
Kim, H.
Lee, J.
Yang, J.
Powiązania:
https://bibliotekanauki.pl/articles/1813396.pdf
Data publikacji:
2008-03
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.07.-b
78.55.-m
Opis:
We synthesized $SiO_x$ nanowires with diameters of 30-140 nm, for the first time by the simple heating of the Mo-coated Si substrates. X-ray diffraction, selected area electron diffraction, and energy-dispersive X-ray spectroscopy indicated that the nanowires were in an amorphous state, comprising Si and O only. Fitting the photoluminescence spectrum with Gaussian functions revealed that the nanowires exhibited significant photoluminescence intensities near blue and green light regions. We extensively discussed the possible growth mechanism of $SiO_x$ nanowires.
Źródło:
Acta Physica Polonica A; 2008, 113, 3; 1017-1020
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Catalyst-Free Growth of Magnesium Oxide Whiskers and Their Characteristics
Autorzy:
Kim, H.
Kong, M.
Yang, J.
Powiązania:
https://bibliotekanauki.pl/articles/1813397.pdf
Data publikacji:
2008-03
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.07.-b
78.55.-m
Opis:
This study reports the production of magnesium oxide (MgO) whiskers on silicon (Si) substrates by the thermal heating of $MgB_2$ powders. We investigated the structural properties of the as-synthesized whiskers by using X-ray diffraction, transmission electron microscopy, selected area electron diffraction, and scanning electron microscopy. The product consisted of one-dimensional whiskers with a square cross-section. The whiskers had a single-crystalline cubic structure of MgO. The photoluminescence measurement with the Gaussian fitting exhibited visible light emission bands centered at 2.39 eV and 2.91 eV. We proposed the growth of MgO whiskers to follow the vapor-solid mechanism.
Źródło:
Acta Physica Polonica A; 2008, 113, 3; 1021-1024
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Study on Discharge Characteristics by Using MF and RF Power in Remote Dielectric Barrier Discharge
Autorzy:
Kim, D.
Shim, Y.
Kim, H.
Han, J.
Powiązania:
https://bibliotekanauki.pl/articles/1398758.pdf
Data publikacji:
2016-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
52.77.Bn
Opis:
We have developed an atmospheric pressure plasma apparatus of remote dielectric barrier discharge (RDBD) applicable for a large area. We have systematically studied the characteristics of medium frequency (MF, 40 kHz) and radio frequency (RF, 13.56 MHz) discharge using an optical emission spectroscope. Nitrogen (N₂) and argon (Ar) gases were used in the MF and RF discharge excitation, respectively, in a mixture with clean dry air (CDA). The peak of oxygen radical (O*₂) appears at 259.3 nm when the RDBD is employed. Furthermore, intensive peaks are observed at gas ratios of N₂:CDA=100:1 in MF excitation and at gas ratios of Ar:CDA=70:0.5 in RF discharge excitation. On the other hand, the contact angle shows about 5° in PET samples after the RDBD treatment using the RF and MF discharge excitation. Surface analyses of polyethylene terephthalate (PET) samples were carried out using an atomic force microscope and X-ray photoelectron spectroscope.
Źródło:
Acta Physica Polonica A; 2016, 129, 4; 707-710
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of natural organic matter on adsorption of ionic and non-ionic pharmaceuticals to granular activated carbon
Autorzy:
Oh, H.
Urase, T.
Simazaki, D.
Kim, H.
Powiązania:
https://bibliotekanauki.pl/articles/208222.pdf
Data publikacji:
2013
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
adsorpcja
grupa karboksylowa
kwas klofibrowy
granulowany węgiel aktywny
węgiel aktywny
naturalne substancje organiczne
farmaceutyki
adsorption
carboxylic group
clofibric acid
granular activated carbons
natural organic matters
pharmaceuticals
Opis:
Adsorption of clofibric acid (CA) and propyphenazone (PPZ) to virgin granular activated carbon (GAC) and preloaded GAC was evaluated in the absence or presence of natural organic matter (NOM). In spite of lower log K ow, PPZ showed higher selectivity to GAC than CA, which has a carboxylic group. Adsorption competition between CA and PPZ in binary solutes system decreased the amount of individual compound adsorbed to GAC. Adsorption isotherm data obtained in the presence of NOM showed that NOM in bulk solution or preloaded on GAC could significantly reduce the amounts of CA and PPZ adsorbed to GAC.
Źródło:
Environment Protection Engineering; 2013, 39, 4; 15-28
0324-8828
Pojawia się w:
Environment Protection Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of checklists for agricultural safety management
Autorzy:
Kim, H.
Rasanen, K.
Chae, H.
Lee, K.
Powiązania:
https://bibliotekanauki.pl/articles/2081898.pdf
Data publikacji:
2018
Wydawca:
Instytut Medycyny Wsi
Tematy:
checklist
agriculture
safety
management
Opis:
Introduction. The current health and safety management system under the Occupational Health and Safety Act has avoided agriculture in Korea. It is important to consider the various safety systems used in agricultural health and safety to develop effective regulations. Objective. The aims were to classify and review the items from various checklists using safety systems, such as design, training, etc., ultimately aimed at proposing directions for improving the health and safety of farmers. Materials and method. Among the retrieved checklists with Google, four were chosen for this study, based on criteria such as the Checklist developed by an international organization, as well as others. Each item on the checklist was categorized using criteria concerning safety systems, developed based on previous studies. Results. The total number of analyzed items was 573, which is 36 more than the actual number of checklist items (537). The proportion of items belonging to the training/procedures system was the highest (32.5%); the second-highest was for the mitigation system – 18.2%.; the third-largest proportion of items was maintenance/inspection – with 14.3%. Items related to the design and human factor systems were 8.2% and 5.6%, respectively. The safety system with the lowest proportion was the warning/notification system – 4.2% of the total items. The proportion of items that could not be classified into safety systems was found to be 16.1%. Conclusions. A large number of items belonging to the training/procedures system reported as occasionally not effective in prevention of injury were found in the checklists. It appears important to develop checklist items proposing the supplementation of various safety systems, rather than presenting items that are biased towards certain safety systems.
Źródło:
Annals of Agricultural and Environmental Medicine; 2018, 25, 3; 494-499
1232-1966
Pojawia się w:
Annals of Agricultural and Environmental Medicine
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure And Thermoelectric Properties Of TAGS-90 Compounds Fabricated By Mechanical Milling Process
Mikrostruktura i właściwości termoelektryczne związków TAGS-90 wytworzonych przez mielenie
Autorzy:
Kim, H.-S.
Babu, M.
Hong, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/353404.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
TAGS-90
thermoelectric properties
high-energy milling
SPS
właściwości termoelektryczne
mielenie wysokoenergetyczne
Opis:
TAGS-90 compound powder was directly prepared from the elements by high-energy ball milling (HEBM) and subsequently consolidated by a spark plasma sintering (SPS). Effect of milling time on the microstructure and thermoelectric properties of the samples were investigated. The particle size of fabricated powders were decreased with increasing milling time, finally fine particles with ~1μm size was obtained at 90 min. The SPS samples exhibited higher relative densities (>99%) with fine grain size. X-ray diffraction analysis (XRD) and energy dispersion analysis (EDS) results revealed that all the samples were single phase of GeTe with exact composition. The electrical conductivity of samples were decreased with milling time, whereas Seebeck coefficient increased over the temperature range of RT~450°C. The highest power factor was 1.12×10-3 W/mK2 obtained for the sample with 90 min milling at 450°C.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1231-1234
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies