Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "braking power" wg kryterium: Wszystkie pola


Tytuł:
Examining the braking energy recovery in a vehicle with a hybrid drive system
Badania odzysku energii hamowania pojazdu o napędzie hybrydowym
Autorzy:
Gajek, A.
Strzępek, P.
Powiązania:
https://bibliotekanauki.pl/articles/1364003.pdf
Data publikacji:
2015
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
vehicle with a hybrid drive system
regenerative braking
braking energy
braking power
pojazd o napędzie hybrydowym
hamowanie odzyskowe
energia hamowania
moc hamowania
Opis:
Results of examining the braking energy recovery in a passenger car with a hybrid system driving the front wheels have been presented. The tests were carried out on a vehicle with a series-parallel system, which combined an internal combustion engine with an electric motor. Such a system makes it possible to change the electric motor operation mode so that it becomes a generator, which charges a high-voltage battery with the use of the vehicle braking energy. The battery charging current was measured at braking with various vehicle deceleration values. The algorithm of controlling the battery charging current, the share of the energy recovered in the total braking energy, and the power of the regenerative braking in relation to the total braking power demand were analysed. The instantaneous power demand at braking on a horizontal road with a low rolling resistance coefficient was determined. The share of the electric power in the energy balance of the braking process as well as the demand and recovery of energy during this process were examined.
W artykule przedstawiono wyniki badań odzysku energii hamowania osobowego samochodu o napędzie hybrydowym kół przednich. Badaniom poddano pojazd z szeregowo równoległym, spalinowo-elektrycznym, hybrydowym układem napędowym. Układ ten umożliwia zamianę rodzaju pracy silnika elektrycznego na pracę prądnicową i ładowanie baterii wysokonapięciowej z wykorzystaniem energii hamowania. Wykonano pomiary prądu ładowania baterii podczas hamowania przy różnych opóźnieniach ruchu pojazdu. Przeanalizowano algorytm sterowania prądem ładowania, udział energii odzyskanej w stosunku do całkowitej energii hamowania oraz moc hamowania odzyskowego w stosunku do całkowitego zapotrzebowania mocy hamowania. Przedstawiono chwilowe zapotrzebowanie mocy przy hamowaniu na jezdni poziomej o niewielkim współczynniku oporów toczenia. Przebadano udział mocy elektrycznej w bilansie energetycznym hamowania oraz zapotrzebowanie i odzysk energii podczas procesu hamowania.
Źródło:
Archiwum Motoryzacji; 2015, 68, 2; 49-60
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena rozkładu średniej temperatury pary ciernej tarcza hamulcowa-okładzina wraz z obsadą hamulcową w czasie hamowania ze stałą mocą
Evaluation of the average temperature distribution of a disc brake-brake pad with caliper during braking with constant braking power
Autorzy:
Sawczuk, W.
Tomaszewski, F.
Powiązania:
https://bibliotekanauki.pl/articles/155026.pdf
Data publikacji:
2013
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
kolejowy hamulec tarczowy
okładzina cierna
obsada hamulcowa
rozkład średniej temperatury
badania termowizyjne
railway disc brake
friction pad
caliper brake
distribution of average temperature
thermal research
Opis:
: Jednym z badań prowadzonych na bezwładnościowym stanowisku hamulcowym jest pomiar temperatury tarczy dla hamulca tarczowego lub temperatury obręczy dla hamulca klockowego przy różnych symulacjach hamowań pociągu. Celem artykułu jest ocena wyników badań rozkładu średniej temperatury tarczowego układu hamulcowego, w szczególności tarcza hamulcowa-okładzina cierna wraz z obsadą hamulcową uzyskanych z pomiaru przy użyciu kamery termowizyjnej w warunkach stanowiskowych. Przeprowadzone badania termowizyjne pozwalają na ocenę zarówno jakościową jak i ilościową zmiany rozkładu średniej temperatury elementów pary ciernej hamulca spowodowaną zużyciem okładzin ciernych.
Measurement of the disc temperature of a disc brake or the rim temperature of a block brake at various simulated train brakings is one of the tests carried out at an inertia brake station. In case of temperature tests of a railway disc brake, in accordance with the guidelines presented in [1], thermocouples installed on the friction surface of the brake disc are used. Behaviour of the average temperature is defined on the basis of six thermocouples mounted in threes on each side of the friction collar. The thermocouples on each side of the disc are placed every 120 ° on three different radii of the disc. During simulated braking tests of the disc, in accordance with a test programme provided for a railway disc brake [2], the waveforms of the average temperature of the disc as a function of the braking time are recorded. This is especially important during trials of brakings from high speeds: 200 and 300 km/h with high pressures of pads to the disc and large braking masses in case of brakings of trains with goods carriages. Then the heat load limit of the brake is checked. The purpose of this paper is to analyse the results of research on behaviour of the average temperature obtained from the measurement of the railway disc brake system, in particular the disc brake, the friction pads brake and caliper (Figs. 6 and 7) using a thermographic camera in station tests. The research show that the measurements using a thermal imaging camera can substantially extend the scope of bench research on the brake disk. It is possible to determine the temperature average increment on the components of the braking system as a result of changes in the thickness of the friction pads.
Źródło:
Pomiary Automatyka Kontrola; 2013, R. 59, nr 9, 9; 938-941
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of FFT Fast Fourier Transform to the vibration signal generated by the disc brake to assess the wear of friction pads during braking with the constant braking power
Zastosowanie szybkiej transformaty Fouriera FFT do sygnału drganiowego generowanego przez hamulec tarczowy do oceny zużycia okładzin ciernych w czasie hamowania na spadku
Autorzy:
Sawczuk, W.
Tomaszewski, F.
Powiązania:
https://bibliotekanauki.pl/articles/263326.pdf
Data publikacji:
2013
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
railway disc brake
diagnostics of brake
frequency analysis
kolejowy hamulec tarczowy
diagnostyka hamulca
analiza widmowa
Opis:
Attempt to raise train speed involves application of greater braking power i.e. braking systems rapidly absorbing and dispersing stored heat energy. To maintain high efficiency of braking system in the whole operational process. it is necessary to control the friction set: brake and pad before reaching limit wear particularly of friction pads. The purpose of this article is to present possibility to diagnose the friction set of disc brake by using selected frequency characteristics of vibration signal generated by brake caliper with friction pads. The purpose of this research is to apply vibration signal of pad calipers to assess the wear of friction pads of disc brake during braking with the constant braking power.
W pojazdach szynowych, ze względu na coraz to większe prędkości jazdy, prowadzi się prace nad udoskonalaniem układów hamulcowych tak, aby zatrzymanie pojazdu odbyło się na możliwie najkrótszej drodze hamowania. Również szereg zalet tego rodzaju hamulca, jak np. stały przebieg współczynnika tarcia w funkcji prędkości w stosunku do tradycyjnego hamulca klockowego, uzasadnia jego stosowanie i to zarówno w pojazdach kolejowych, jak i w pojazdach szynowych komunikacji miejskiej. Mimo wielu zalet układu hamulcowego, zamocowanie tarcz hamulcowych na osi pomiędzy kołami zestawu kołowego znacznie utrudnia kontrolę zużycia pary ciernej tarcza-okładzina. Wymusza ono na obsłudze i pracownikach zakładów naprawczych wchodzenie pod wagon w celu zdiagnozowania układu hamulcowego, sprawdzenia poprawności jego działania, kontroli zużycia oraz przeprowadzenia niektórych napraw bieżących. Brak stałego monitorowania zużycia elementów ciernych hamulca powoduje, że w niektórych przypadkach dochodzi do całkowitego zużycia okładzin ciernych i tarcia obsad hamulcowych o tarczę hamulcową. Celem artykułu jest wykorzystanie sygnału drganiowego obsad z okładzinami do oceny zużycia okładzin ciernych hamulca tarczowego, wyznaczając charakterystyki w dziedzinie częstotliwości, podczas badań na bezwładnościowym stanowisku hamulcowym.
Źródło:
Archiwum Motoryzacji; 2013, 3; 43-52, 127-136
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental method of determining characteristics of power and torque engine for low-power unmanned aerial vehicles
Autorzy:
Jastrzębski, G.
Ułanowicz, L.
Powiązania:
https://bibliotekanauki.pl/articles/245545.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
transport
internal combustion engines
motor test
motor braking
Opis:
The article presents an analytical determination of power and torque of internal combustion engines of small power. It measured actual power and torque characteristics of internal combustion engines of small power. Three types (methods), braking (receiving power via a hydraulic pump, generator and a package of propellers with variable angle of attack. For each method of receiving power (braking) determined the characteristics of torque and power. There is the summary of results for one engine with different ways of braking. There have been evaluation of the presented methods inhibit combustion piston engines of small power as methods for determining power internal combustion engines. The analysis methods presented in the perspective of the braking engine selection for light unmanned aircraft, and the use of parameters derived from research into engine control. Subject to the evaluation method of adjustment (increase) charged, increasing the load on a liquid or ankle. The criterion for comparing methods for inhibition of internal combustion engines of small power load assumed dependence on the rotational speed n, and obtain maximum power on the motor shaft when the throttle, a reflection of the actual engine operating parameters in its target applications.
Źródło:
Journal of KONES; 2011, 18, 3; 135-142
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Improvement of transient stability by means of a series braking resistor
Poprawa stabilności kątowej przejściowej poprzez załączanie szeregowego rezystora hamującego
Autorzy:
Robak, S.
Gryszpanowicz, K.
Powiązania:
https://bibliotekanauki.pl/articles/396926.pdf
Data publikacji:
2017
Wydawca:
ENERGA
Tematy:
power system
transient stability
series braking resistor
system elektroenergetyczny
stabilność kątowa przejściowa
szeregowy rezystor hamujący
Opis:
The article discusses the use of a series braking resistor to improve the transient stability of a power system. In the case under consideration, a series braking resistor is used to keep the synchronism of synchronous generators after a three-phase short-circuit in a transmission line nearby of power plant. Braking resistors have recently been increasingly used in power engineering. This focus of this paper is on how the resistor is incorporated into the generator unit and on the generator braking intensity during a fault. Theoretical considerations were confirmed by simulation tests in a test system.
Artykuł dotyczy zastosowania szeregowego rezystora hamującego do poprawy stabilności kątowej przejściowej systemu elektroenergetycznego. W rozpatrywanym przypadku szeregowy rezystor hamujący wykorzystywany jest do ratowania synchronizmu generatorów synchronicznych po wystąpieniu bliskiego elektrowni 3-fazowego zwarcia w linii przesyłowej. W ostatnim okresie można zauważyć wzrost zastosowań rezystorów hamujących w elektroenergetyce. W tym artykule uwaga została skupiona na sposobie włączenia rezystora w układ blokowy generatora oraz na intensywności hamowania generatora w trakcie trwania zwarcia. Rozważania teoretyczne potwierdzono za pomocą badań symulacyjnych dla systemu testowego.
Źródło:
Acta Energetica; 2017, 4; 111-115
2300-3022
Pojawia się w:
Acta Energetica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A layered compensation optimization strategy of energy storage type railway power conditioner
Autorzy:
Wang, Ying
He, Yianqiang
Chen, Xiaoqiang
Zhao, Miaomiao
Xie, Jing
Powiązania:
https://bibliotekanauki.pl/articles/2042792.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
electrified railway
energy storage system
negative sequential governance
railway power conditioner
regenerative braking energy
Opis:
Aiming at the problems of the negative sequence governance and regenerative braking energy utilization of electrified railways a layered compensation optimization strategy considering the power flow of energy storage systems was proposed based on the railway power conditioner. The paper introduces the topology of the energy storage type railway power conditioner and analyzes its negative sequence compensation and regenerative braking energy utilization mechanism considering the influence of equipment capacity and power flow of the energy storage system on railway power conditioner compensation effect, the objective function and constraint conditions of the layered compensation optimization of the energy storage type railway power conditioner were constructed and the sequential quadratic programming method was used to solve the problem. The feasibility of the proposed strategy is verified by a multicondition simulation test. The results show that the proposed optimization compensation strategy can realize negative sequence compensation and regenerative braking energy utilization, improve the power factor of traction substations when the system equipment capacity is limited and it also has good realtime performance.
Źródło:
Archives of Electrical Engineering; 2022, 71, 1; 5-20
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Passenger cars in the 21st century. Some engineering design problems
Samochody osobowe w XXI wieku. Pewne problemy konstrukcyjne
Autorzy:
Szczepaniak, C.
Powiązania:
https://bibliotekanauki.pl/articles/1364752.pdf
Data publikacji:
2012
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
hamulce
kierowanie
napęd
samochód
silniki
zawieszenie
braking systems
engines
motor-car
power transmission systems
suspension systems
vehicle steering
Opis:
The paper deals with some engineering design problems related to the motor cars that are to be manufactured in the early decades of the 21st century. The general construction concept of these "cars of the future" will not significantly differ from that followed at present. Instead, the vehicle development will be focused on the introduction of improvements and new engineering solutions to basic vehicle motion systems, such as power transmission, braking, steering, and suspension systems with running gear, and to the auxiliary vehicle equipment that is to ensure the highest possible standard of active and passive safety of vehicle operation, e.g. automatic systems to control the vehicle motion or additional systems intended to improve the ride comfort and, directly, safety of vehicle occupants. Attention has been separately paid to vehicle engines that may be used in the future and to the construction of vehicle bodies. The possibilities that might be offered thanks to the availability of new technologies have also been taken into account at the discussion of the engineering design solutions of the future.
W artykule zostały przedstawione pewne problemy konstrukcyjne samochodów osobowych, które mają być produkowane w pierwszych dekadach XXI wieku. Samochody te będą budowane stosownie do obowiązującej dzisiaj ogólnej zasady konstrukcyjnej. Ich rozwój będzie się realizował w nowych rozwiązaniach podstawowych układów ruchu oraz w wyposażeniu, które ma zapewnić wysoki stopień bezpieczeństwa ruchu w wymiarze bezpieczeństwa aktywnego i pasywnego. Podstawowe układy ruchu stanowią: układ napędowy, hamulcowy, kierowniczy, zawieszenia, jezdny. Wyposażenie zwiększające stopień bezpieczeństwa biernego i czynnego to automatyczne sterowanie układami ruchu oraz dodatkowe systemy zwiększające komfort jazdy i bezpośrednio bezpieczeństwo pasażerów. Oddzielna uwaga jest zwrócona na silniki napędowe, które mogą być wykorzystywane w przyszłości oraz na budowę nadwozi. W omawianiu przyszłych rozwiązań konstrukcyjnych wzięto pod uwagę możliwości, jakie zapewni pojawianie się nowych technologii.
Źródło:
Archiwum Motoryzacji; 2012, 4; 47-56
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Power flows in a hydrostatic-mechanical transmission of a mining locomotive during the braking process
Autorzy:
Samorodov, Vadym
Bondarenko, Anatoliy
Taran, Igor
Klymenko, Iryna
Powiązania:
https://bibliotekanauki.pl/articles/1841202.pdf
Data publikacji:
2020
Wydawca:
Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:
transmission
mine diesel locomotive
power flows
braking process
transmisja
górnicza lokomotywa spalinowa
przepływy mocy
proces hamowania
Opis:
This paper considers the braking process of a mine diesel locomotive with hydrostatic mechanical transmission (HSMT) operating according to the “input differential” scheme. Braking process modeling involves four implementation methods. Identification and systematization of basic regularities in the distribution of power flows within a closed transmission contour in the process of braking have been performed with the help of software support developed by means of MatLab/Simulink. The simulation results of braking due to the hydrostatic transmission and the braking system during the movement of a diesel locomotive in the transport and traction ranges are presented in the form of graphical correlations. The process of theoretical studies of the braking process of a diesel locomotive with HSMT operating according to the “input differential” scheme has helped determine that, in terms of deceleration at the expense of a hydrostatic drive (HSD) and braking system while preserving kinematic engine-wheels connection, it is not permitted to implement this method of braking process as it is followed by excess of the allowable value of working pressure differential within HSD up to 2.8 times.
Źródło:
Transport Problems; 2020, 15, 3; 17-28
1896-0596
2300-861X
Pojawia się w:
Transport Problems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Recovery braking of variable-structure electronic commutator for BLDC motor
Autorzy:
Biskup, T.
Powiązania:
https://bibliotekanauki.pl/articles/140812.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
power electronics
BLDC motor
electronic commutator
electric vehicle
Opis:
Permanent magnet motors are more and more frequently used in various applications. In this group motors with a trapezoidal EMF deserve a special attention. They are characterized by a simple construction, high efficiency and high torque overload. A certain drawback of BLDC motors are difficulties with an operation at a speed above the nominal value. The article presents the results of investigations into the variablestructure electronic commutator designed for the drive of a small electric vehicle equipped with BLDC motors. Such a solution allows extending the standard range of the drive's speed. The considerations contained in the article focus on the possibilities and effects of regeneration mode in the proposed topology of converter. A theoretical analysis has been presented as well as computer simulations carried out by means of Matlab- Simulink, which were then verified at a laboratory. The tests were finished with trias conducted using a small electric vehicle Elipsa.
Źródło:
Archives of Electrical Engineering; 2012, 61, 4; 579-596
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analytical model for investigation of the effect of friction power on thermal stresses in friction elements of brakes
Autorzy:
Topczewska, K.
Powiązania:
https://bibliotekanauki.pl/articles/281308.pdf
Data publikacji:
2018
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
frictional heating
temperature
specific power of friction
braking
thermal stresses
Opis:
The influence of the change with time of friction power on thermal stresses in a friction element of a brake system is investigated. For this purpose, a list of ten different temporal profiles of specific friction power is used, which has been experimentally established for a single braking process. The corresponding profiles of transient temperature fields in the considered element are applied as input parameters to find quasi-static thermal stresses. Numerical analysis concerned with spatio-temporal distributions of the stresses and their evolutions on the heated surface is presented.
Źródło:
Journal of Theoretical and Applied Mechanics; 2018, 56, 4; 1017-1027
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies