Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "vehicle fuel" wg kryterium: Temat


Tytuł:
Some aspect of theory of cumulated fuel consumption
Autorzy:
Sitnik, L. J.
Powiązania:
https://bibliotekanauki.pl/articles/247685.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
vehicle
engine
fuel consumption
Opis:
A theory of cumulated fuel consumption in process ofvehicle operation is described. The method of creation the mathematical model and procedure of determination of model variables is shown. The mainfeatures of cumulated fuel consumption are painted attention. li is shown that the theory of cumulated fuel consumption can be use to description of the fuel consumption from beginning the exploitation of vehicles and also for the situation when the vehicle are in exploitation from any time and further fuel consumption are unknown. An example of utilisation of elaborated theory for assessment of operation of passenger car is also presented. It has been shown that applying the theory of cumulated fuel consumption, the course of such consumption can be accurately described also in this case. This proposal can be formulated in spite of making some simplifications. This is because the unknown value of the accumulated fuel before start the time of observation operation will be determined using the average (from the average) fuel consumption. This simplification greatly facilitates the flow of the calculations and it seems does not offend errors in the calculations. Method of determining the average is discussed in the article. It appears that such treatment may be justified by the fact that the mistake is, in principle, systematic error. Very high coefficients of mathematical model to fit the measured data are very interesting. Such regularity was observed during researches in buses transport [l], intercity buses, and the fleets of various vehicles (the results of researches are not yet published).The introduction of the theory of cumulated fuel consumption as one of the important parameters to assess the operation of the vehicle or vehicles may also be useful in exploitation researches. At present times the researches in which the vehicles are already in service and the engine control mops are tuned (chip tuning), are made. A good performance of these changes is often observed on chassis dyno but that is not properly sanctioned in natural exploitation. Experimentation with such issue is underway and will be the subject of future analysis (and publications).
Źródło:
Journal of KONES; 2010, 17, 4; 447-453
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Projections of the fuel consumption by the road transport in Poland
Autorzy:
Chłopek, Z
Waśkiewicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/245285.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
transport
motor transport
vehicle
annual mileage
fuel consumption
Opis:
The article presents expert estimates for 2010 and a forecast up to year 2030 regarding the number of passenger cars as well as trucks and special vehicles and buses according to the maximum weight group. In case of trucks and special vehicles, included were vehicles with maximum weight of less than 3.5 Mg and maximum weight of more than 3.5 Mg. As regards buses – the condition and forecast number of buses with maximum weight of less than 5.0 Mg and more than 5.0 Mg was presented. The forecast concerning passenger cars and other types of vehicles with maximum weight of less than 3.5 Mg (5.0 Mg in case of buses) focused on the number of vehicles by type of energy. The following types of energy were included: petrol, diesel oil, LPG, NG and electrical energy in case of passenger cars and light duty trucks. Estimates also included the average annual statistical mileage of a vehicle registered in Poland according to the specified category and type of energy. Based on the assumed assumptions in the 2030 perspective – the average fuel consumption was determined per 100 km of statistical mileage in every specified category. The predicted consumption of respective types of energy by the overall Polish car fleet was calculated and according to the specified category in years 2015, 2020, 2025 and 2030.
Źródło:
Journal of KONES; 2013, 20, 2; 33-39
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Conditions for optimizing powertrain performance in a vehicle with an internal combustion engine
Autorzy:
Janulin, Michał
Powiązania:
https://bibliotekanauki.pl/articles/1835548.pdf
Data publikacji:
2020
Wydawca:
Uniwersytet Warmińsko-Mazurski w Olsztynie
Tematy:
optimization
powertrain
gear ratio
vehicle energy efficiency
fuel consumption
Opis:
The paper presents optimization of the drive system in terms of adapting it to the characteristics of another engine. Powertrain parameters in a vehicle with an internal combustion engine were selected based on the following criteria: fuel consumption, engine dynamics, and emission standards for harmful substances. A light-duty passenger vehicle with gross vehicle weight rating (GVWR) of 3.5 tons was modified by replacing a spark-ignition engine with a diesel engine. The gear ratio in the powertrain had to be modified accordingly to optimize the engine’s performance, enhance engine dynamics, minimize fuel consumption and toxic emissions. The optimization of selected parameters of the vehicle driveline was performed based on the requirements of the standard NEDC and WLTC cycles.
Źródło:
Technical Sciences / University of Warmia and Mazury in Olsztyn; 2020, nr 23(4); 291-307
1505-4675
2083-4527
Pojawia się w:
Technical Sciences / University of Warmia and Mazury in Olsztyn
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Determination of the deviation of the on-board computer in the vehicle when determining the average fuel consumption
Autorzy:
Loman, Michal
Šarkan, Branislav
Powiązania:
https://bibliotekanauki.pl/articles/1838343.pdf
Data publikacji:
2021
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
fuel consumption
vehicle
onboard computer
service station
measurement uncertainty
Opis:
Fuel consumption measurement itself is a demanding process and it is difficult to determine the exact consumption of a vehicle. Fuel consumption can be determined in various ways. One way to determine consumption is through driving tests. We know several types of driving tests. Nowadays, most vehicles and all new vehicles can provide a wealth of data to the driver directly during vehicle operation. One of them is the data on the consumption of the vehicle also through the on-board computer located in the vehicle. The information provided to the driver may not reflect reality. In most cases, they are inaccurate and do not correspond to reality. Therefore, the subject of the research will be to verify the accuracy of the provided data on vehicle consumption by the on-board computer. The aim of the research will be to determine the extent to which consumption data are true. Vehicle consumption, as well as measurements are performed on one vehicle in every day traffic. This will ensure that it is possible to compare the measured data with each other.
Źródło:
Archiwum Motoryzacji; 2021, 91, 1; 25-35
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of energy efficiency and dynamics during car acceleration
Autorzy:
Graba, Mariusz
Bieniek, Andrzej
Prażnowski, Krzysztof
Hennek, Krystian
Mamala, Jarosław
Burdzik, Rafał
Śmieja, Michał
Powiązania:
https://bibliotekanauki.pl/articles/24200840.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
acceleration
fuel consumption
energy consumption
vehicle dynamics
acceleration dynamic index
Opis:
In this work, the authors focused on analyzing the energy efficiency and dynamics during car acceleration, featuring investigation of acceleration dynamics under various acceleration intensities. The tests were performed in the speed range between 45 km/h and 120 km/h, at a constant gear ratio. This enabled obtaining variable dynamic parameters of the acceleration process, ranging from about 0.1 to 1.4 m/s2, and recording variation in fuel consumption from 6.28 to 27.03 dm3/100km. The study focused on determining the relation between fuel consumption, energy efficiency and vehicle acceleration depending on the available drivetrain power. The relation between fuel consumption and vehicle acceleration was described by using the dynamic index. The proposed dynamic index takes into account the energy (from burned fuel) and vehicle acceleration intensity to obtain an objective metric for characterizing the acceleration process. The aforementioned index takes the form of the passenger car movement energy quality index and can be related to widely known physical properties, thus ensuring its universality. The index expresses the energy expenditure within the time needed to accelerate a vehicle weighing 1kg by a 1m distance. As opposed to other criteria that are applied to the assessment of passenger cars dynamics, the index shows a high determination coefficient R2 in excess of 0.99, and can be used as a universal metric to test other vehicle types.
Źródło:
Eksploatacja i Niezawodność; 2023, 25, 1; art. no. 17
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison of mileage fuel consumption with the natural operation of the three different cycles
Autorzy:
Sitnik, L. J.
Magdziarz-Tokłowicz, M.
Walkowiak, Wł.
Wróbel, R.
Włostowski, R.
Powiązania:
https://bibliotekanauki.pl/articles/243579.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
fuel consumption
mileage fuel consumption
resistance to motion
energy consumption of traffic
vehicle operation
SI engine
Opis:
In the automotive industry in the world continuously being sought universal driving cycle. The test should closely match the fuel consumption and emissions of toxins in the fumes of the test vehicle in its real operating conditions [4]. However, in the previously developed solid driving tests established velocity profiles differ significantly from actual driving conditions. The difference in fuel consumption, comparing the natural operation of the NEDC test reaches an average of 18%. The new version of the driving cycle should be more realistic to the everyday use of additional equipment and gadgets that are installed in modern vehicles [1]. The impact on fuel consumption by vehicles may be conditioned not only by its size and weight, but also by the geometry of the track motion, forces causing the motion and the forces acting on the car when driving on curved tracks. The vehicle encounters and overcomes all the forces that act on it while driving-resistance movement. In the energy intake through the vehicle runs in the motor changes at the expense of the energy of fuel consumed. The driving force performs work on a given stretch of road balancing (predominant) friction. On the basis of the calculated resistance movement and the energy consumption of the movement in the selected object was a comparison of the actual consumption of fuel in the vehicle with the ignition spark. Analysis was performed and found differences in three cycles: urban, extra-urban and combined.
Źródło:
Journal of KONES; 2014, 21, 4; 439-444
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The emission factor and a vehicle run-in period
Autorzy:
Hlavńa, V.
Krakovsky, T.
Powiązania:
https://bibliotekanauki.pl/articles/242358.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
vehicle run-in period
emission factor
fuel consumption
testing
European legislation
Opis:
During operation on road and due to gradual ageing ofa vehicle, the formation of gaseous pollutants undergoes certain evolution. At the start of the vehicle life the evolution is influenced mostly by the run-in period of the driving mechanism. Motor vehicle manufacturers state that the vehicle run-in period ends after the vehicle has run from 3,000-15,000 kilometers depending on the engine type and transmission mechanism. During the run-in period the fuel consumption decreases and the production of emissions slightly changes, which consequently influences the emission factor. (The emission factor is understood as the ratio between the pollutant produced and the amount of consumed fuel). A theoretical value of the difference in the fuel consumption between the new and run-in vehicle is about 8% in favor of the run-in vehicle. The European legislation does not specify after how many kilometers the vehicle stops to be considered new. This can lead to disputes when testing emissions from the new vehicle and those from the vehicle having the control software already installed. The contribution outlines apossibility of determining the coefficient for calculation of emissions and fuel consumption for the first tested vehicle and for the one that has coveredfrom 60 to 300 kilometres. It may contribute to the optimization of the control software installed in the vehicle.
Źródło:
Journal of KONES; 2009, 16, 2; 175-181
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the reference fuel consumption and CO2 emission of vehicle with using of the map of operating conditions for selected agglomeration
Autorzy:
Kropiwnicki, J.
Powiązania:
https://bibliotekanauki.pl/articles/244045.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
road transport
simulation
vehicle operating conditions
fuel consumption
CO2 emission
Opis:
Vehicle operating fuel consumption estimation has a measurable significance for both individual users as well as transport and Communications companies. Complex analysis of the results may cause reduction of power (fuel) consumption, CO2 and toxic compounds emissions in exhaust gases. Operating fuel consumption estimation carried out by drivers' encounters basic difficulties connected with the lach of reliable reference standard for comparison of measured fuel consumption during car usage. Therefore it is necessary to identify vehicle operating conditions and ascribe them reference fuel consumption according to the accepted reference standard. A method of description ofreal vehicle operating conditions has been presented in this paper. Presented examples show that vehicle operating conditions may be unambiguously described with the use of proposed indicators. They can be also used to forecast the fuel consumption with high accuracy. Exclusive use of certification tests as model of operating conditions for this purpose does not allow keeping high conformity of assumptions with usage practice. Creation ofan individual map of operating conditions for a chosen agglomeration would enable to optimize choice of vehicle or fleet for an intended place of operation. Utilization of such operating conditions map may be: to determine reference fuel consumption for assumed operation area or optimal route of drive from the point of view of minimizing fuel consumption, energy or CO2 emission to the atmosphere. Selected examples of Utilization of such operating conditions map have been presented.
Źródło:
Journal of KONES; 2010, 17, 3; 239-246
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of high-speed traction gearbox ratio on vehicle fuel consumption
Wplyw przelozenia szybkobieznosci na zuzycie paliwa pojazdu
Autorzy:
Golebiewski, W.
Stoeck, T.
Powiązania:
https://bibliotekanauki.pl/articles/792794.pdf
Data publikacji:
2012
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
high-speed traction
gearbox
fuel consumption
mileage fuel consumption
energy consumption
vehicle
engine torque
ecology
economy
linear velocity
Źródło:
Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2012, 12, 1
1641-7739
Pojawia się w:
Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelling of motor vehicle operation for the evaluation of pollutant emission and fuel consumption
Autorzy:
Chłopek, Z.
Biedrzycki, J.
Lasocki, J.
Wójcik, P.
Samson-Bręk, I.
Powiązania:
https://bibliotekanauki.pl/articles/134075.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
vehicle driving test cycles
pollutant emission
fuel consumption
emisja zanieczyszczeń
zużycie paliwa
Opis:
A novel approach to modelling of motor vehicle operation by employing special test cycles threated as realizations of the stochastic process of vehicle velocity is presented. The families of test cycles were designed to simulate driving conditions in street congestion, urban, extra-urban, and high-speed traffic. The data necessary for the development of test cycles was obtained in the empirical investigations conducted in real road traffic. The recorded velocity time-histories were analysed in the time, frequency, and process value domains. Fragments of the velocity vs. time curves, representative for the considered driving conditions, were selected to design test cycles. The statistical examination of those test cycles demonstrated that individual process realizations are similar to each other and to all the process realizations recorded during the empirical tests.
Źródło:
Combustion Engines; 2017, 56, 4; 156-163
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Symulacyjna ocena wpływu wartości przełożenia na właściwości trakcyjne samochodu i zużycie paliwa
Simulation of impact assessment ratios on the properties of traction vehicle and fuel consumption
Autorzy:
Lisowski, M.
Powiązania:
https://bibliotekanauki.pl/articles/314334.pdf
Data publikacji:
2011
Wydawca:
Instytut Naukowo-Wydawniczy "SPATIUM"
Tematy:
właściwości trakcyjne
samochód ciężarowy
zużycie paliwa
traction properties
truck vehicle
fuel consumption
Opis:
W artykule przedstawiono wyniki symulacji właściwości trakcyjnych samochodu ciężarowego dla różnych wartości przełożenia całkowitego w układzie napędowym. Symulacji dokonano na przykładzie samochodu ciężarowego Jelcz 317 z silnikiem SW-680. Przedstawiono również charakterystyki zużycia paliwa przez samochód dla pełnego i częściowego obciążenia.
The paper presents results of simulations of traction properties of truck for different values of the ratio of the total propulsion system. Simulation was done on the example of a truck engine Jelcz 317 SW-680. Also presents the characteristics of a car's fuel consumption for the full and partial load.
Źródło:
Autobusy : technika, eksploatacja, systemy transportowe; 2011, 12, 5; 270-275
1509-5878
2450-7725
Pojawia się w:
Autobusy : technika, eksploatacja, systemy transportowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Possibilities for decreasing fuel consumption of rail vehicle of independent traction
Autorzy:
Mikolajčík, M.
Kalinčák, D.
Powiązania:
https://bibliotekanauki.pl/articles/251491.pdf
Data publikacji:
2015
Wydawca:
Instytut Naukowo-Wydawniczy TTS
Tematy:
rail vehicle
fuel consumption
independent traction
pojazd szynowy
zużycie paliwa
przyczepa niezależna
Opis:
Article deals with issue of fuel consumption reduction of rail vehicle of independent traction. It's necessary to make analysis of operating conditions of rail vehicles for proper solution of this problems and therefrom of result choose the best solution contributing to fuel consumption reduction. It's necessary take into account economical aspect too. Some trends, which are using for design of rail vehicles in present and have effect to fuel consumption reduction and better fuel utilization (dual engine, using of waste heat of ICE, hybrid and etc.) will be also mentioned in this article.
Źródło:
TTS Technika Transportu Szynowego; 2015, 12; 1071-1076, CD
1232-3829
2543-5728
Pojawia się w:
TTS Technika Transportu Szynowego
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Determination of specific fuel consumption of IC engine in transient conditions
Wyznaczanie jednostkowego zuzycia paliwa silnika spalinowego w warunkach nieustalonych
Autorzy:
Grzelka, J.
Powiązania:
https://bibliotekanauki.pl/articles/792124.pdf
Data publikacji:
2012
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
combustion engine
spark ignition engine
fuel consumption
transient condition
motor vehicle
satellite navigation system
fuel injection system
vertical profile
route
telecommunication
Źródło:
Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2012, 12, 1
1641-7739
Pojawia się w:
Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigations of the influence of engine thermal state on the fuel consumption of passenger vehicles
Autorzy:
Adamski, W.
Polak, S.
Powiązania:
https://bibliotekanauki.pl/articles/133704.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
passenger vehicle
fuel consumption
engine thermal state
samochód osobowy
zużycie paliwa
stan cieplny silnika
Opis:
The paper presents the results of investigations of the fuel consumption of two vehicles performed for non-stabilized engine temperature in the start and warm up phases. The measurements were performed in a wide range of ambient temperatures from –18°C to +25°C. In order to obtain such conditions the tests were carried out in a climate chamber.
Źródło:
Combustion Engines; 2017, 56, 2; 49-52
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of steering course of CVT to diesel fuel consumption an exhaust emission at ECE cycle
Autorzy:
Pawelski, Z.
Pałczyński, T.
Powiązania:
https://bibliotekanauki.pl/articles/242790.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
engine steering
continuous variable transmission
fuel consumption
exhaust emission
modelling and simulation of vehicle drivetrain
Opis:
Present article shows the influence of steering course of CVT-Continuous Variable Transmission to engine load trajectory at established vehicle speed profile by engine throttle. In this aim, at the first part is shown vehicle and their driveline model. There was described simulating model and the main subsystem having major influence to analyzed problem, made near help of MatLab Simulink R2007a software. There was shown one and multi objective optimal lines conception. At the second part, there was presented proposition of CVT steering course at four Variants, and also shown results of simulating investigation for proposed Variants. At final part, there was analyzed results of simulating investigations and future work according to presented problems. Results of work showed the influence control graph of drive on the trajectory of an engine load. The control graph of stepless drive is relative to the profile of the speed and the universal engine performance. It is possible to change work range by graph choice of system, wherethrough one can exclude programmatically unfavorable areas on work of the combustion engine.
Źródło:
Journal of KONES; 2007, 14, 4; 335-342
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies