Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

English (EN)·Polski (PL)·Yкраїнський (UK)
Przejdź do strony domowej biblioteki Centralna Biblioteka Wojskowa Link otwiera się w nowym oknie Logo biblioteki Prolib Integro - strona głównaCentralna Biblioteka Wojskowa

Wyszukujesz frazę "Lee, S.-H." wg kryterium: Autor

  Lista filtrów
Wyrównaj
Wyświetlanie 1-15 z 47
Tytuł:
Microstructure and Mechanical Properties of AA1050/ AA6061/AA1050 Multi-Layer Sheet Fabricated by Cold Roll Bonding Process
Autorzy:
Lee, S.-H.
Powiązania:
https://bibliotekanauki.pl/articles/353150.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
cold roll bonding process
AA1050/AA6061/AA1050 complex sheet
mechanical properties
electron backscatter diffraction
microstructure
Opis:
A cold roll-bonding process was applied to fabricate an AA1050/AA6061/AA1050 multi-layer sheet. Three Al sheets in which an AA6061 sheet is inserted inside two AA1050 sheets of 2 mm thickness, 40 mm width and 300 mm length were stacked up after surface treatment, and the material was then reduced to a thickness of 1.0 mm by multi-pass cold rolling. The AA1050/AA6061/AA1050 laminate complex sheet fabricated by roll bonding was then hardened by a natural aging (T4) and an artificial aging (T6) treatments. The microstructures of the as-roll bonded and the age-hardened Al complex sheets were revealed by optical microscope and electron back scatter diffraction analysis, and the mechanical properties were investigated by tensile and hardness testing. The strength of the as-roll bonded complex sheet was found to increase by 2.6 times, compared to that value of the starting material. Both AA1050 and AA6061 showed a typical recrystallization structure in which the grains were equiaxed after heat treatment. However, the grain size was smaller in AA6061 than in AA1050.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1489-1492
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect Of Compaction Pressure And Sintering Temperature On The Liquid Phase Sintering Behavior Of Al-Cu-Zn Alloy
Wpływ ciśnienia prasowania i temperatury spiekania na spiekanie stopu Al-Cu-Zn z udziałem fazy ciekłej
Autorzy:
Lee, S. H.
Ahn, B.
Powiązania:
https://bibliotekanauki.pl/articles/351836.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
powder metallurgy
liquid phase sintering
compaction pressure
Al-Cu-Zn alloy
metalurgia proszków
spiekanie w fazie ciekłej
ciśnienie prasowania
stop Al-Cu-Zn
Opis:
The liquid phase sintering characteristics of Al-Cu-Zn alloy were investigated with respect to various powder metallurgy processing conditions. Powders of each alloying elements were blended to form Al-6Cu-5Zn composition and compacted with pressures of 200, 400, and 600 MPa. The sintering process was performed at various temperatures of 410, 560, and 615°C in N2 gas atmosphere. Density and micro-Vickers hardness measurements were conducted at different processing stages, and transverse rupture strength of sintered materials was examined for each condition, respectively. The microstructure was characterized using optical microscope and scanning electron microscopy. The effect of Zn addition on the liquid phase sintering behavior during P/M process of the Al-Cu-Zn alloy was also discussed in detail.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1485-1489
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication And Mechanical Properties Of A Nanostructured Complex Aluminum Alloy By Three-Layer Stack Accumulative Roll-Bonding
Wytwarzanie i właściwości mechaniczne nanostrukturalnego złożonego stopu aluminium wytworzonego przez walcowanie pakietowe trzech warstw
Autorzy:
Lee, S. H.
Lee, S. R.
Powiązania:
https://bibliotekanauki.pl/articles/351499.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
accumulative roll-bonding (ARB)
aluminum alloy
microstructre
mechanical properties
akumulacyjne walcowanie pakietowe
stop aluminium
mikrostruktura
właściwości mechaniczne
Opis:
A multi-layered complex aluminum alloy was successfully fabricated by three-layer stack accumulative roll bonding(ARB) process. The ARB using AA1050 and AA5052 alloy sheets was performed up to 7 cycles at ambient temperature without lubrication. The specimen processed by the ARB showed a multi-layer aluminum alloy sheet in which two aluminum alloys are alternately stacked. The grain size of the specimen decreased with the number of ARB cycles, became about 350nm in diameter after 7cycles. The tensile strength increased with the number of ARB cycles, after 6c it reached 281MPa which is about twice higher than that of the starting material. The microstructures and mechanical properties of a three-layer AA1050/AA5052 alloy fabricated by the ARB were compared to those of the conventional ARB-processed material.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1195-1198
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of Mo-Si-B Intermetallic Compound Powders Under Different Heat Treatment Conditions
Autorzy:
Park, J. H.
Lee, S.
Kim, D.
Kim, Y.
Yang, S. H.
Lee, S. H.
Powiązania:
https://bibliotekanauki.pl/articles/353369.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Mo-Si-B alloys
intermetallic compounds
reitveld refinement
T2 phase
A15 phase
Opis:
In this research, we investigated the effects of reduction atmospheres on the creation of the Mo-Si-B intermetallic compounds (IMC) during the heat treatments. For outstanding anti-oxidation and elevated mechanical strength at the ultrahigh temperature, we fabricated the uniformly dispersed IMC powders such as Mo5SiB2 (T2) and Mo3Si (A15) phases using the two steps of chemical reactions. Especially, in the second procedure, we studied the influence of the atmospheres (e.g. vacuum, argon, and hydrogen) on the synthesis of IMCs during the reduction. Furthermore, the newly produced IMCs were observed by SEM, XRD, and EDS to identify the phase of the compounds. We also calculated an amount of IMCs in the reduced powders depending on the atmosphere using the Reitveld refinement method. Consequently, it is found that hydrogen atmosphere was suitable for fabrication of IMC without other IMC phases.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1509-1512
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics Of The Porous Body Sintered By Nano-Sized Fe-Cr-Al Alloy Powder
Charakterystyka porowatego korpusu spiekanego z nanometrycznego proszku stopu Fe-Cr-Al
Autorzy:
Lee, S.-I.
Lee, S.-H.
Gu, B.-U.
Lee, D.-W.
Kim, B.-K.
Powiązania:
https://bibliotekanauki.pl/articles/356635.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Fe-Cr-Al powder
metallic sponges
sintering temperature
oxidation resistance
proszek Fe-Cr-Al
proszek nanometryczny
temperatura spiekania
odporność na utlenianie
Opis:
Porous metal with uniform honeycomb structure was successfully produced by sintering using Fe-Cr-Al nano powder, which was prepared by the pulsed wire evaporation (PWE) in ethanol. Its process consisted of the several steps; 1) coating on the surface of polyurethane sponge with the liquid droplets generated from the ethanol-based slurry where the Fe-Cr-Al nano powders were uniformly dispersed, 2) heat treatment of debinding to remove the polyurethane sponge and 3) sintering of the porous green body formed by Fe-Cr-Al nano powders. The strut thickness of porous Fe-Cr-Al was increased by the increase of spraying times in ESP step. Also, The shrinkages and the oxidation resistance of the sintered porous body was increased with increase of sintering temperature. The optimal sintering temperature was shown to 1450°C in views to maximize the oxidation resistance and sinterability.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1275-1279
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication and Characterization of CoCrFeNiMn High Entropy Alloy Powder Processed by Gas Atomization
Autorzy:
Park, T. G.
Lee, S. H.
Lee, B.
Cho, H. M.
Choi, W. J.
Kim, B. S.
Shin, K. S.
Kim, T.-S.
Powiązania:
https://bibliotekanauki.pl/articles/353649.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high entropy alloy
gas atomization
spark plasma sintering
CoCrFeNiMn
Opis:
In this study, precisely controlled large scale gas atomization process was applied to produce spherical and uniform shaped high entropy alloy powder. The gas atomization process was carried out to fabricate CoCrFeNiMn alloy, which was studied for high ductility and mechanical properties at low temperatures. It was confirmed that the mass scale, single phase, equiatomic, and high purity spherical high entropy alloy powder was produced by gas atomization process. The powder was sintered by spark plasma sintering process with various sintering conditions, and mechanical properties were characterized. Through this research, we have developed a mass production process of high quality and spherical high entropy alloy powder, and it is expected to expand applications of this high entropy alloy into fields such as powder injection molding and 3D printing for complex shaped components.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1055-1059
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of Porous Silica Fibers by Electrospinning for Sound Absorbing Materials
Autorzy:
Cho, Y.-S.
Lee, H. J.
Powiązania:
https://bibliotekanauki.pl/articles/353561.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
electrospinning
porous silica fiber
thermal insulator
sound absorption
Opis:
Macroporous silica fibers having spherical cavities were fabricated by electrospinning using the spinning solution prepared from the mixed dispersion of tetraethylorthosilicate (TEOS) and polystyrene nanospheres as precursor and sacrificial templates, respectively, by injection through metallic nozzle. By applying electric field, the electro-spun fibers obtained by evaporation-driven self-assembly were collected on flat substrate or rotating drum, followed by the removal of the templates by calcination. The sound absorption coefficient of the porous fibers was measured by impedance tube, and the measured value was larger than 0.9 at high frequency region of incident waves. The surface of the resulting fibers was modified using fluorine-containing silane coupling agent to produce superhydrophobic fibrous materials to prevent the infiltration of humidity.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1497-1502
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Morphology Change Of Si Deposit In Molten Salt Electrorefining
Zmiana morfologii osadu Si podczas elektrorafinacji w stopionych solach
Autorzy:
Ryu, H. Y.
Kwon, S. C.
Han, M. H.
An, Y. S.
Lee, J. S.
Lee, J. H.
Powiązania:
https://bibliotekanauki.pl/articles/354346.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
molten salt
silicon
morphology
electrorefining
current density
sól stopiona
krzem
morfologia
elektrorafinacja
gęstość prądu
Opis:
The effects of processing parameters on the morphology change in a Si deposit recovered by means of molten salt electrorefining are evaluated using electrochemical techniques such as cyclic voltammetry and chronopotentiometry at 800°C. It was found that concentration of K2SiF6 and current density were important parameters in determining deposit size. Higher concentrations of K2SiF6 were effective in coarsening the silicon deposit and decreasing the cell potential. Silicon nanofiber was recovered at 5 wt% of K2SiF6 whereas dense particles were prepared at 30 and 50 wt% of K2SiF6. The morphology of the Si deposit was determined by the concentration of Si in the electrolyte which is related to the formation of crystal and growth of Si. The formation mechanism of the Si deposit was interpreted by using high resolution TEM as well as electrochemical properties.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1491-1497
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and Magnetic Properties of NdFeB Sintered Magnets Diffusion-Treated with Cu/Al Mixed Dyco Alloy-Powder
Autorzy:
Lee, M.-W.
Bae, K.-H.
Lee, S.-R.
Kim, H.-J.
Jang, T.-S.
Powiązania:
https://bibliotekanauki.pl/articles/353351.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Nd-Fe-B sintered magnets
grain boundary diffusion process
low melting point element
DyCo alloy-powder diffusion
Opis:
We investigated the microstructural and magnetic property changes of DyCo, Cu + DyCo, and Al + DyCo diffusion-treated NdFeB sintered magnets. The coercivity of all diffusion treated magnet was increased at 880ºC of 1st post annealing(PA), by 6.1 kOe in Cu and 7.0 kOe in Al mixed DyCo coated magnets, whereas this increment was found to be relatively low (3.9 kOe) in the magnet coated with DyCo only. The diffusivity and diffusion depth of Dy were increased in those magnets which were treated with Cu or Al mixed DyCo, mainly due to comparatively easy diffusion path provided by Cu and Al because of their solubility with Ndrich grain boundary phase. The formation of Cu/Al-rich grain boundary phase might have enhanced the diffusivity of Dy-atoms. Moreover, relatively a large number of Dy atoms reached into the magnet and mostly segregated at the interface of Nd2 Fe14 B and grain boundary phases covering Nd2 Fe14 B grains so that the core-shell type structures were developed. The formation of highly anisotropic (Nd, Dy)2Fe14B phase layer, which acted as the shell in the core-shell type structure so as to prevent the reverse domain movement, was the cause of enhancing the coercivity of diffusion treated NdFeB magnets. Segregation of cobalt in Nd-rich TJP followed by the formation of Co-rich phase was beneficial for the coercivity enhancement, resulting in the stabilization of the metastable c-Nd2O3 phase.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1263-1266
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Enhancement of Life Time of the Dimensionally Stable Anode for Copper Electroplating Applications
Autorzy:
Son, S. H.
Park, S. C.
Lee, M. S.
Powiązania:
https://bibliotekanauki.pl/articles/356684.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
dimensionally stable anode
surface treatment
life time
copper
electrodeposition
Opis:
In order to enhance the long-term stability of DSA for copper electroplating process, in the present study, noble metal oxides with excellent electrochemical properties was used and optimum condition was determined the ratio of noble metal oxides, surface pre-treatment of titanium substrate and heat treatment. The effect of the surface pretreatment of titanium substrate and ratio of noble metal oxides were estimated by accelerated test at the highly current density conditions. The lifetime of DSA increase six-fold higher as the oxide thickness of Ta 7 : Ir 3 composition ratio. Under the optimal condition, surface pretreatment led to dramatic increase in the lifetime of DSA.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1019-1022
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication Of Zn4Sb3 Alloys By A Combination Of Gas-Atomization And Spark Plasma Sintering Processes
Wytwarzanie i konsolidacja proszków stopowych zn4sb3 przez kombinację procesów atomizacji gazowej i spiekania
Autorzy:
Dharmaiah, P.
Kim, H.-S.
Lee, L. H.
Hong, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/355894.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
gas atomization
microstructure
spark plasma sintering (SPS)
X-ray diffraction
atomizacja gazowa
mikrostruktura
SPS
spiekanie plazmowe
analiza rentgenowska (XRD)
Opis:
In this study, single phase polycrystalline Zn4Sb3 as well as 11 at.% Zn-rich Zn4Sb3 alloy having ε-Zn4Sb3 (majority phase) and Zn (minority phase) phases bulk samples produced by gas-atomization and subsequently consolidated by spark plasma sintering (SPS) process. The crystal structures were analyzed by X-ray diffraction (XRD) and cross-sectional microstructure were observed by the scanning electron microscopy (SEM). The internal grain microstructure of 11at.% Zn-rich Zn4Sb3 powders shows lamellar structure. Relative density, Vickers hardness and crack lengths were measured to investigate the effect of sintering temperature of Zn4Sb3 samples which are sintered at 653, 673 and 693 K. Relative density of the single phase bulk Zn4Sb3 sample reached to 99.2% of its theoretical density. The micro Vickers hardness of three different sintering temperatures were found around 2.17 – 2.236 GPa.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1417-1421
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Aluminum Oxide Formation On Fecral Catalyst Support By Electro-Chemical Coating
Powstawanie tlenku glinu na nośniku katalizatora FeCrAl przez osadzanie elektrochemiczne
Autorzy:
Yang, H. S.
Jang, D. H.
Lee, K. J.
Powiązania:
https://bibliotekanauki.pl/articles/355942.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
FeCrAl
catalyst support
aluminum oxide formation
PEO
plasma electrolytic oxidation
electrochemical coating
nośnik katalizatora
tlenek glinu
plazmowe utlenianie elektrolityczne
elektrochemiczne osadzanie
Opis:
FeCrAl is comprised essentially of Fe, Cr, Al and generally considered as metallic substrates for catalyst support because of its advantage in the high-temperature corrosion resistance, high mechanical strength, and ductility. Oxidation film and its adhesion on FeCrAl surface with aluminum are important for catalyst life. Therefore various appropriate surface treatments such as thermal oxidation, Sol, PVD, CVD has studied. In this research, PEO (plasma electrolytic oxidation) process was applied to form the aluminum oxide on FeCrAl surface, and the formed oxide particle according to process conditions such as electric energy and oxidation time were investigated. Microstructure and aluminum oxide particle on FeCrAl surface after PEO process was observed by FE-SEM and EDS with element mapping analysis. The study presents possibility of aluminum oxide formation by electro-chemical coating process without any pretreatment of FeCrAl.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1503-1506
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characterization of Cu and Ni Nano-Fluids Synthesized by Pulsed Wire Evaporation Method
Autorzy:
Kim, H.-S.
Yilmaz, F.
Dharmaiah, P.
Lee, D.-J
Lee, T.-H.
Hong, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/356475.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
pulsed wire evaporation
nanofluid
Cu
Ni
suspension stability
dispersibility
Opis:
In the present work, Cu and Ni nanofluids were synthesized using the pulsed wire evaporation (PWE) method in the different aqueous medias, namely (ethanol and ethylene glycol), and the effects of the aqueous media on the dispersion state, stability, and particle size of nanoparticles were studied. The size and morphology of synthesized nano-particles were investigated by transmission electron microscopy (TEM). Also, the dispersion stability of the nanofluids was evaluated by turbiscan analysis. The TEM results showed that the nano-particles were spherical in shape, and the average particle size was below 100 nm. The average particle size of the Cu nano-particles was smaller than that of Ni, which was attributed to a difference in the specific sublimation energy of the elements. Moreover, ethylene glycol (EG) exhibited higher suspension stability than ethanol. Finally, the dispersion stability of Cu@EG displayed the highest value due to lower particle size and greater viscosity.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 999-1004
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect Of Heat-Treatment On Microstructure And Magnetic Properties Of Nanocrystallized Mn-Zn Ferrite Powders
Wpływ obróbki cieplnej na mikrostrukturę i właściwości magnetyczne nanokrystalicznych proszków ferrytu Mn-Zn
Autorzy:
Lee, W. H.
Hong, C. S.
Chang, S. Y.
Powiązania:
https://bibliotekanauki.pl/articles/351552.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high energy ball milling
nanosized particles
crystallite size
magnetic properties
frezowanie kulowe
nanocząstki
wielkości krystalitów
właściwości magnetyczne
Opis:
The initial ferrite powders were subjected to high energy ball milling at 300rpm for 3h, and subsequently heat-treated at 573-1273K for 1h. Based on the observation of microstructure and measurement of magnetic properties, the heat-treatment effect was investigated. The size of initial powders was approximately 70μm. After milling, the powders with approximately 230nm in size were obtained, which were composed of the nano-sized particles of approximately 15nm in size. The milled powders became larger to approximately 550nm after heat-treatment at 973K. In addition, the size of particles increased to approximately 120nm with increasing temperature up to 973K. The coercivity of initial powders was almost unchanged after milling, whereas the saturation magnetization increased. As the heat-treatment temperature increased, the saturation magnetization gradually increased and the maximum coercivity was obtained at 773K.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1347-1350
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Self-Consolidation and Surface Modification of Mechanical Alloyed Ti-25.0 at.% Al Powder Mixture by Using an Electro-Discharge Technique
Autorzy:
Chang, S. Y.
Jang, H. S.
Yoon, Y. H.
Kim, Y. H.
Kim, J. Y.
Lee, Y. K.
Lee, W. H.
Powiązania:
https://bibliotekanauki.pl/articles/354212.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
sintering
mechanical alloying
powder consolidation
intermetallic compounds
titanium aluminides
Opis:
Electrical discharges using a capacitance of 450 μF at 0.5, 1.0, and 1.5 kJ input energies were applied in a N2 atmosphere to obtain the mechanical alloyed Ti3Al powder without applying any external pressure. A solid bulk of nanostructured Ti3Al was obtained as short as 160 μsec by the Electrical discharge. At the same time, the surface has been modified into the form of Ti and Al nitrides due to the diffusion process of nitrogen to the surface. The input energy was found to be the most important parameter to affect the formation of a solid core and surface chemistry of the compact.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1293-1297
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Wyświetlanie 1-15 z 47

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies