Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "wirnik" wg kryterium: Temat


Tytuł:
Interferencja wirnik nośny - wirnik ogonowy
Interference between the main and tail rotors
Autorzy:
Łusiak, T.
Powiązania:
https://bibliotekanauki.pl/articles/212441.pdf
Data publikacji:
2006
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
interferencja
wirnik nośny
wirnik ogonowy
interference
main rotor
tail rotor
Opis:
W artykule przedstawiono modele zaburzeń opływu śmigłowca w płaszczyźnie wirnika ogonowego wywołanych bliskością wirnika nośnego. Przedstawiono model śladu zawirnikowego w oparciu o zasadę Biota i Savarta w celu określenia zaburzeń pola prędkości indukowanej przez wirnik nośny w płaszczyźnie wirnika ogonowego [4].
The influence of disturbances to the flow around a helicopter resulting from a resultant reaction of the wake from the main rotor on the tail rotor, on the loading as well as control and noise of the helicopter was presented. The analysis was based on a rotational model of the system. The basis of the model of the interference is the replacement of wake generated by rotors and fixed lifting surfaces by a uniform rotational model in the form of discrete rotational grids. This allows for the integration of fields induced through all rotational elements of the system, in accordance with the Biot-Savart law. This law was accepted in view of the fact that, as the only law included in the flow model, it enables a constant processing of load calculations in an undefined flight, with the retention of a reasonable calculation time. The undertaking of this subject should help explain phenomena not completely recognized and which exert a significant influence on safety when operating helicopters certain states of flight. The results of modeling, carried out for the SW4 helicopter, contain an evaluation of disturbances of the field of flow around the tail rotor in given states of flight, in which the case of take-off in a sidewind and with the carrying out of a directional maneuver is of primary significance. In other cases, when the tail rotor does not enter into intensive disturbances of the velocity field by the main rotor, the interference phenomena are of lesser importance. The numerical program used allows for information about flow around and loads on the taił rotor in flow disturbed by the (main) rotor to be obtained. Resultant loads on the tail rotor can be evaluated, along with its chosen elements.
Źródło:
Prace Instytutu Lotnictwa; 2006, 1-2 (184-185); 198-202
0509-6669
2300-5408
Pojawia się w:
Prace Instytutu Lotnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Silnik asynchroniczny z wirnikiem z płynnej stali
Asynchronous motor with rotor of liquid steel
Autorzy:
Graczyk, M.
Powiązania:
https://bibliotekanauki.pl/articles/1374884.pdf
Data publikacji:
2005
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
silniki asynchroniczne
wirnik
stal
Opis:
To achieve high quality and homogeneity of steel, in technology - continuous casting technology stirring and mixing of melt should be done. The paper describes equipment for stirring provided by rotating magnetic field. The magnetic field is generated by two-pole copper coils placed on the core made of electrotechnical laminations. The winding is supplied from low-frequency converter. In Research and Development Centre of Electrical Machines KOMEL two types of stirrer were designed and manufactured for "Huta Zawiercie" steelworks. First stirrers work over 6 years without damage, the second part of larger stirrers were implemented in 2004.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2005, 71; 47-50
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Szanse dalszego rozwoju sprężarek wirnikowych
Autorzy:
Kawalec, K.
Powiązania:
https://bibliotekanauki.pl/articles/212302.pdf
Data publikacji:
2009
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
wirnik
dyfuzor
birotacyjność
trójkąty prędkości
Opis:
Na tle obecnego stopnia rozwoju sprężarek wirnikowych w lotniczych silnikach turbinowych i tłokowych przedstawiono możliwości radykalnego wzrostu ich osiągów przez zastosowanie nowatorskiego pomysłu birotacyjności wirników tych maszyn i ich dyfuzorów. W Instytucie Lotnictwa powstał pomysł, którego efekty potwierdzono badaniami przepływowymi, a nowatorstwo patentami uzyskanymi w Polsce, ZSRR, USA i Kanadzie. Realizacja pomysłu dotyczy w równym stopniu sprężarek promieniowych, diagonalnych oraz osiowych.
Źródło:
Prace Instytutu Lotnictwa; 2009, 4 (199); 91-94
0509-6669
2300-5408
Pojawia się w:
Prace Instytutu Lotnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Silniki klatkowe dużej mocy do często powtarzanych lub długo trwających rozruchów
Big capacity squirrel cage motors for frequently repeated or long lasting starts
Autorzy:
Bernatt, J.
Bernatt, M.
Powiązania:
https://bibliotekanauki.pl/articles/1369373.pdf
Data publikacji:
2012
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
silniki klatkowe
rozruch
wirnik silnika
Opis:
High capacity induction squirrel cage motors used at different industrial driver are usually started by switching direct on line. Starting current, several times higher than nominal load current, causes thermal and mechanical, dynamic stresses dangerous for motor's structure. Both, stator and rotor windings are endangered at starting period, but stresses in rotor cages are usually considerable higher, therefore rotor design (and its manufacturing process) is of high importance for motor's durability.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2012, 4, 97; 43-47
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Solid rotor induction machine optimisation by using analytical and finite element techniques
Optymalizacja maszyny indukcyjnej z wirnikiem litym przy użyciu metod analitycznych i metody elementów skończonych
Autorzy:
Theodoropoulos, I.
Tatis, K.
Kladas, A.
Tegopoulos, J.
Powiązania:
https://bibliotekanauki.pl/articles/159273.pdf
Data publikacji:
2003
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Elektrotechniki
Tematy:
maszyny indukcyjne
maszyny asynchroniczne
wirnik
Opis:
An optimisation procedure for solid rotor induction machines, exhibiting important advantages for micro-machine production due to the simplicity of their construction, is presented. Both non-salient and salient rotor structures have been considered and compared. Design optimisation has been performed based on the finite element method and analytical solutions in case of regular geometries combined with sensitivity analysis techniques. The developed models precision has been checked by comparing their results for the same machine configuration.
Przedstawiono procedurę optymalizacji maszyn indukcyjnych z wirnikiem litym, wykazujących ważne zalety dla produkcji mikromaszyn ze względu na prostotę ich budowy. Uwzględniono i porównano zarówno wirniki z biegunami utajonymi jak i wydatnymi. Optymalizację budowy przeprowadzono w oparciu o metodę elementów skończonych i o rozwiązania analityczne w przypadku regularnych geometrii wirnika w połączeniu z metodami analizy wrażliwości. Dokładność opracowanych modeli sprawdzono przez porównanie ich wyników dla tej samej konfiguracji maszyny.
Źródło:
Prace Instytutu Elektrotechniki; 2003, 216; 7-16
0032-6216
Pojawia się w:
Prace Instytutu Elektrotechniki
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Silnik reluktancyjny z toczącym się wirnikiem dyskowym
Rolling disc - shape rotor switched reluctance motor
Autorzy:
Kamiński, G.
Herbst, A.
Powiązania:
https://bibliotekanauki.pl/articles/1373447.pdf
Data publikacji:
2009
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
maszyna elektryczna
silnik reluktancyjny
wirnik
Opis:
The article describes construction and operational principles of rolling disc – shape rotor switched reluctance motor. In first part of the article, rotor kinematics and special mechanical properties are described. Few methods of control are also presented. The second part of article consist magnetic calculations (which were done with Vector FieldsŽ Opera 3D software) as a way to find the optimal construction parameters and control algorithm. In the third part of the article author describes results of tests of drive system with prototype motor.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2009, 83; 135-138
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Pradnice synchroniczne z magnesami trwałymi umieszczonymi wewnątrz wirnika
Interior premanent magnet synchronous generators
Autorzy:
Król, E.
Rossa, R.
Powiązania:
https://bibliotekanauki.pl/articles/1374058.pdf
Data publikacji:
2008
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
prądnica synchroniczna
magnes trwały
wirnik
Opis:
In the paper two kinds of permanent magnet synchronous generator constructions are compared. The first one is generator with the arc-segment permanent magnets mounted on the rotor surface (Surface Permanent Magnet - SPM construction). The second one is generator with the block-segment permanent magnets mounted inside the rotor's laminated core (Interior Permanent Magnet - IPM construction). The results of laboratory tests for both kinds of generators operating stand-alone are presented and discussed. It can be concluded from these test results and discussions, that IPM generator is characterized by a lower voltage variations and higher efficiency in the entire range of loads. It is also characterized by higher mechanical strength and higher reliability comparing to the SPM construction.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2008, 80; 159-162
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Silniki indukcyjne z miedzianą odlewaną klatką wirnika - nowe problemy i nowe perspektywy
Induction motors with die - casting cooper rotors new problems and new prospects
Autorzy:
Zapaśnik, R.
Powiązania:
https://bibliotekanauki.pl/articles/1374359.pdf
Data publikacji:
2007
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
silnik indukcyjny
klatka wirnika
wirnik
Opis:
Inclusion in the last time the research centers and the great manufacturers to topic of the motors with die - casting copper rotors has caused that on the one hand the new technological and material problems have been elicited and on the other hand the new fields of the application of the such motors have been discovered.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2007, 76; 1-4
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Silniki elektryczne z magnesami trwałymi umieszczonymi na wirniku
Electric motors with permanent magnets placed in the rotor
Autorzy:
Glinka, T.
Jakubiec, M.
Powiązania:
https://bibliotekanauki.pl/articles/1374813.pdf
Data publikacji:
2005
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
silniki elektryczne
magnesy trwałe
wirnik
Opis:
Electric motors with permanent magnets placed along rotor's circumference may operate as: -synchronous motors with permanent magnets (PM SM) -sinusoidally controlled brushless dc motors with permanent magnets (PMDC BMSC) -trapezoidally controlled brushless dc motors with permanent magnets (PMDC BMTC). In each case the electromechanical properties of the drive are different, this is influenced by the control method and electromagnetic field distribution in the armature slot. The induction distribution should induce sinusoidal rotation voltage in the armature winding of PMSM and PMDCBMSC and trapezoidal rotation voltage in PMDCBMTC, respectively. Synchronous motors are supplied with voltage of set (forced) frequency. The rotational speed is controlled by changing the supply voltage frequency. The mathematical model of synchronous motors in steady and quasi-steady states is given in Equations (2-10). The electronic commutator in brushless pm motor is built into the motor, same as mechanical commutator in dc motors. The electronic commutator is supplied with dc voltage. The windings' current is of variable character, but its frequency depends on the rotational speed of the motor. This speed is controlled and set by changing the electronic commutator supply voltage. If the current waveforms generated by electronic commutator in A, B, C phases windings are trapezoidal, then the motor is denoted as trapezoidally controlled. The mathematical model of this motor is given in Equations (11-14). If the current waveforms generated by electronic commutator in A, B, C phases windings are sinusoidal, then the motor is denoted as sinusoidally controlled. The mathematical model of the motor is given in Equations (15-20).
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2005, 71; 103-111
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Silniki indukcyjne z miedzianą odlewaną klatką wirnika
Induction motors with die-casting cooper rotors
Autorzy:
Zapaśnik, R.
Powiązania:
https://bibliotekanauki.pl/articles/1374882.pdf
Data publikacji:
2005
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
silniki indukcyjne
klatka wirnika
wirnik
Opis:
Die-cast copper rotor motors as the new kind of the squirrel cage induction motors. Main performance of the motors where copper has been substituted for aluminum in the rotor squirrel cage. Today's word-wide situation in the field of the production of the die-cast copper rotor induction motors. Perspectives of the industrial expansion of this kind of motors as the profitable alternative to ordinary motors with aluminum squirrel cage.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2005, 71; 1-6
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelowanie utraty stabilności układu wirnik-łożyska przy stochastycznej zmienności danych wejściowych
Modelling of stability loss of rotor-bearings system with stochastic variation of the input data
Autorzy:
Pietkiewicz, P.
Powiązania:
https://bibliotekanauki.pl/articles/209108.pdf
Data publikacji:
2008
Wydawca:
Wojskowa Akademia Techniczna im. Jarosława Dąbrowskiego
Tematy:
wirnik
niepewność danych
trajektoria
drgania
układ wirnik-łożyska
rotor
data uncertainty
vibrations
rotor-bearings system
Opis:
Artykuł zawiera wybrane wyniki obliczeń potwierdzających możliwość symulacji utraty stabilności przez układ wirnik-łożyska obciążonego siłą poprzeczną zmienną w czasie. Opracowane dotąd modele nie były wykorzystywane do tego typu prób. Przedstawione wyniki obliczeń dotyczą dwóch wariantów obciążenia wirnika.
The chosen calculation results, confirming the possibility of simulation of the stability loss by the rotor-bearings system, subjected to a time-warying shearing force are presented. Models formulated so far were not applied for such kind of tests. The presented results concern two variants of the rotor loading.
Źródło:
Biuletyn Wojskowej Akademii Technicznej; 2008, 57, 2; 15-22
1234-5865
Pojawia się w:
Biuletyn Wojskowej Akademii Technicznej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ szerokości otwarcia żłobków na parametry eksploatacyjne silnika indukcyjnego małej mocy
Influence of slots width opening on the operating parameters of a small power induction motor
Autorzy:
Antal, L.
Antal, M.
Zawilak, J.
Powiązania:
https://bibliotekanauki.pl/articles/2076289.pdf
Data publikacji:
2005
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
silniki indukcyjne
silniki elektryczne
stojan
wirnik
Opis:
The work presents calculation results of a small (1.5 kW) squirrel cage induction motor. The influence of slots width opening on efficiency and other operating characteristics of the motor was examined. The efficiency calculations were realized by finding distribution of time-harmonic magnetic field in a two-dimensional field-circuit motor model. Calculations for different combination of stator and rotor slot width openings showed influence of these geometric parameters on shape of magnetic field in motor air-gap. Field harmonic analysis shows that there is a possibility to decrease slot harmonics and in consequence, increase motor efficiency and other parameters.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2005, 73; 125-130
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Kontrola jakości blach stojanów i wirników maszyn elektrycznych pod kątem przydatności ich do dalszej eksploatacji
Testing of electrical machines stators and rotors core sheets with regard to his future utilisation
Autorzy:
Rad, M.
Rams, W.
Powiązania:
https://bibliotekanauki.pl/articles/1372414.pdf
Data publikacji:
2011
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
maszyna elektryczna
stojan
wirnik
diagnostyka
stratność
Opis:
Conception and realization of core loss measuring is shown in this article. Stators and rotors core sheets are tested during repair, with core windings or when they are removed. Proposed special coefficient kz is a quality measure of isolation between core sheets, and therefore basing on this, it is possible to decide if further repair of machine is advisable or not. System was tested in the laboratory as well as on the real machines with different conditions and constructions. Included results, indicates not only total condition of cores, but also local defects in the examined cases.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2011, 2, 90; 135-139
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Designing and building heavy lifting modification of a radio controlled helicopter
Projekt i budowa udźwigowej wersji śmigłowca zdalnie sterowanego
Autorzy:
Górzyński, M.
Bibik, P.
Powiązania:
https://bibliotekanauki.pl/articles/212375.pdf
Data publikacji:
2017
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
helicopter
rotor
modification
śmigłowiec
wirnik
modyfikacja
Opis:
The paper presents the heavy lifting modification of radio controlled T-Rex 700 DFC PRO helicopter which was originally designed as acrobatic machine. The purpose of designing machine like this is a need for a cheap and reliable machine specifically designed to carry weights for research and development purposes. Thanks to its design there is a possibility to attach to it a measuring apparatus, modules like auto-pilot, and weights. It can be also used to test wide range of rotors and other components which makes it very universal research tool. To achieve those goals the whole frame and landing gear has been redesigned using NX 11 CAD/CAM/CAE to achieve desired cargo space and weight distribution. Additionally the tail has been lengthened to allow use of the rotors with bigger diagonal. All the applied changes has been made to increase the machine payload. The designed elements were fabricated and the helicopter has been tested in flight. During the test flights several performance parameters were measured.
Artykuł niniejszy prezentuje modyfikację do wersji udźwigowej zdalnie sterowanego śmigłowca T-REX 700 PRO DFC, oryginalnie zbudowanego do akrobacji lotniczych. Celem powstania modyfikacji jest zapotrzebowanie na tanie i niezawodne maszyny bezzałogowe do przenoszenia ładunków zarówno dla celów badawczych jak i komercyjnych. Konstrukcja zmodyfikowanego śmigłowca umożliwia przenoszenie aparatury pomiarowej, modułów dodatkowych (np. autopilota) i ładunków. Maszyna ta może być również użyta jako stanowisko testowe dla wirników nośnych i innych podzespołów. Aby spełnić te wymagania rama nośna śmigłowca oraz podwozie zostały przeprojektowane z wykorzystaniem technik CAD/CAM/CAE aby zapewnić uzyskanie odpowiednich przestrzeni ładunkowych oraz właściwe rozmieszczenie wyposażenia. Dodatkowo belka ogonowa została wydłużona, co pozwala na zastosowanie dłuższych łopat wirnika nośnego. Wykonane zmiany doprowadziły do znacznego powiększenia przenoszonego ładunku użytecznego. Zaprojektowane elementy zostały wykonane i przebudowany śmigłowiec został przetestowany w locie. Podczas prób mierzone były podstawowe parametry osiągowe śmigłowca.
Źródło:
Prace Instytutu Lotnictwa; 2017, 4 (249); 35-36
0509-6669
2300-5408
Pojawia się w:
Prace Instytutu Lotnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Pattern of helicopter rotor loads and blade deformations in some states of flight envelope
Obraz obciążeń i odkształceń łopaty wirnika nośnego smigłowca w wybranych stanach lotu
Autorzy:
Stanisławski, J.
Powiązania:
https://bibliotekanauki.pl/articles/213247.pdf
Data publikacji:
2015
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
helicopter
rotor
blade
śmigłowiec
wirnik
łopata
Opis:
Paper contains a calculated range of helicopter rotor loads and deformations of the rotor blades which can occur within the flight envelope in different states: hover, level flight, autorotation, pull-up. The rotor loads were determined by using a computer simulating program including the model of the deformable rotor blade. The equations of motion of the rotor blade were solved by applying Galerkin's method. The results of calculations were presented in the form of plots showing time-run of the loads and the distributions of deformations due to the blade azimuth position on the rotor disk.
Praca obejmuje określenie poziomu zmian obciążeń wirnika nośnego i odkształceń łopat występujących w różnych warunkach lotu możliwych do wystąpienia w granicach obwiedni stanów lotu śmigłowca: zawis, lot poziomy, autorotacja, wyrwanie. Wartości obciążeń elementów wirnika wyznaczono symulacyjnie z zastosowaniem programu komputerowego uwzględniającego model odkształcalnej łopaty. Do rozwiązania równań ruchu łopat wykorzystano metodę Galerkina. Wyniki obliczeń przedstawiono w formie wykresów pokazujących rozkłady obciążeń i odkształceń.
Źródło:
Prace Instytutu Lotnictwa; 2015, 1 (238); 70-90
0509-6669
2300-5408
Pojawia się w:
Prace Instytutu Lotnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies