Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "water tank" wg kryterium: Temat


Tytuł:
Structural damage detection of elevated circular water tank and its supporting system using geodetic techniques
Autorzy:
Zeidan, Zaki
Beshr, Ashraf A. A.
Sameh, Sara
Powiązania:
https://bibliotekanauki.pl/articles/145428.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
zbiornik na wodę
deformacja
nachylenie
dokładność
tachimetr
water tank
deformation
inclination
accuracy
total station
Opis:
Water is the main source of daily life for everyone and everywhere in the world. Sufficient water distribution depends on the place and design of water tank in certain areas. Water storage tanks are relatively flexible structures and they can tolerate greater settlements than other engineering structures. Deformation of tanks may cause severe damages to tank or even loss of life and injury to people, so monitoring the structural deformation and dynamic response of water tank and its supporting system to the large variety of external loadings has a great importance for maintaining tank safety and economical design of manmade structures. This paper presents an accurate geodetic observations technique to investigate the inclination of an elevated circular water tank and the deformation of its supporting structural system (supporting columns and circular horizontal beams) using reflector-less total station. The studied water tank was designed to deliver water to around 55000 person and has a storage capacity about 750 m3. Due to the studied water tank age, a non-uniform settlement of tank foundation and movement of pumps and electric machines under tank’s body will cause stress and strain for tanks membrane and settlement of sediments. So the studied water tank can tend to experience movement vertically, horizontally or both. Three epochs of observations were done (July 2014, September 2014 and December 2014). The results of the practical measurements, calculations and analysis of the interesting deformation of the studied elevated tanks and its supporting system using least squares theory and computer programs are presented. As a results of monitoring the water storage tank, circular reinforced concrete beams and columns at three monitoring epochs. The body of water storage tank has an inclination to the east direction and the value of inclination is increased with the time.
Źródło:
Geodesy and Cartography; 2020, 69, 1; 117-140
2080-6736
2300-2581
Pojawia się w:
Geodesy and Cartography
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wirtualny model zbiorników z wodą w sterowniku PLC
Virtual model of water tanks in the PLC
Autorzy:
Zawalich, J.
Powiązania:
https://bibliotekanauki.pl/articles/269190.pdf
Data publikacji:
2013
Wydawca:
Politechnika Gdańska. Wydział Elektrotechniki i Automatyki
Tematy:
model
zbiorniki z wodą
PLC
water tank
Opis:
Modele obiektów rzeczywistych otrzymuje się na różnorodne sposoby i wykorzystuje w różnorodnych celach. Do badania obiektów automatyki stosuje się najczęściej programy komputerowe, np.: Matlab-Simulink, Scilab, GNU Octave, itp. Można również stosować pamięć operacyjną sterowników [1, 2]. W referacie przedstawiono opis wirtualnego modelu dwóch połączonych zbiorników z wodą w sterowniku PLC. Proste przekształcenia matematyczne pozwalają na zbudowanie algorytmu w języku drabinkowym. Proponowany model w sterowniku PLC może być wykorzystany między innymi do weryfikacji głównego programu sterującego z jednoczesnym śledzeniem przebiegu pracy modelu zbiornika. Sygnały generowane przez główny algorytm sterujący mogą bezpośrednio wpływać na wirtualny model obiektu, a ten z kolei będzie odpowiadał i uruchamiał kolejne sekwencje głównego programu sterującego.
Models of real objects are obtained in a variety of ways and for a variety of uses. To test automation objects are most commonly used computer programs such as Matlab-Simulink, Scilab, GNU Octave, etc. Can be also use the main memory of PLC. This paper describes the virtual model of two connected tanks with water in the PLC. Simple mathematical transformations allow to build a ladder algorithm for PLC. The proposed model in the PLC can be used, among other things, to review the main control program of the tank with water. At the same time can check the work process in virtual model. The signals generated by the main control algorithm can directly influence virtual model of the object. The model are responding and starts the next sequence of the main program.
Źródło:
Zeszyty Naukowe Wydziału Elektrotechniki i Automatyki Politechniki Gdańskiej; 2013, 36; 179-182
1425-5766
2353-1290
Pojawia się w:
Zeszyty Naukowe Wydziału Elektrotechniki i Automatyki Politechniki Gdańskiej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of nodalization effects on the prediction error of generalized finite element method used for dynamic modeling of hot water storage tank
Autorzy:
Wołowicz, M.
Kupecki, J.
Wawryniuk, K.
Milewski, J.
Motyliński, K.
Powiązania:
https://bibliotekanauki.pl/articles/239932.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
dynamic modeling
hot water storage tank
modelowanie dynamiczne
zasobnik gorącej wody sieciowej
Opis:
The paper presents dynamic model of hot water storage tank. The literature review has been made. Analysis of effects of nodalization on the prediction error of generalized finite element method (GFEM) is provided. The model takes into account eleven various parameters, such as: flue gases volumetric flow rate to the spiral, inlet water temperature, outlet water flow rate, etc. Boiler is also described by sizing parameters, nozzle parameters and heat loss including ambient temperature. The model has been validated on existing data. Adequate laboratory experiments were provided. The comparison between 1-, 5-, 10- and 50-zone boiler is presented. Comparison between experiment and simulations for different zone numbers of the boiler model is presented on the plots. The reason of differences between experiment and simulation is explained.
Źródło:
Archives of Thermodynamics; 2015, 36, 3; 123-138
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Determination of reasons of the water contamination on the intake in Wolin including the recovery measures preventing the similar contamination
Ustalenie przyczyn skażenia wody na ujęciu w Wolinie wraz z podaniem środków zaradczych zapobiegających podobnemu skażeniu
Autorzy:
Wira, J.
Wira, D.
Powiązania:
https://bibliotekanauki.pl/articles/84919.pdf
Data publikacji:
2005
Wydawca:
Akademia Pomorska w Słupsku
Tematy:
determination
reason
water contamination
Rybacka Street
20th century
prevention
Wolin town
water intake
water supply station
pumping unit
hydrophore tank
building
household building
water sample
testing
water analysis
chloride concentration
Opis:
The water intake situated at Rybacka Street in Wolin was established in the beginning of the 20th century. It is situated in the close vicinity of the existing apartment and business buildings and the water and sewage systems as well. On the fenced parcel ca 50x80 m besides the objects of: – building of the water-supply station, – warehouse – workshop building with sanitary facilities, – household building, – building of the current generating plant, are situated the deep-water wells No. 6 and No. 9 now in the operational use. The other deep-water wells being now in the operational use are the well No. 10 situated at Rybacka Street in the distance ~ 90 m from the intake parcel border as well as the well No. 5 situated in the distance ~ 220 m from the parcel border.
Zasadniczym czynnikiem, który był powodem zanieczyszczenia wody na ujęciu w Wolinie było skażenie warstwy wodonośnej prowadzonymi w roku 2003 robotami hydrotechnicznymi na nabrzeżu Dziwnej. Biorąc pod uwagę fakt ustania przyczyny skażenia ujęcia, potwierdzony uzyskiwanymi badaniami wody surowej uważamy, że dalsze stałe prowadzenie dezynfekcji wody jest bezzasadne. Zakładając, że zjawisko skażenia warstwy wodonośnej może w przyszłości wystąpić (powtórzyć się), uważamy za zasadne ciągle monitorowanie jakości wody ujmowanej (surowej).
Źródło:
Baltic Coastal Zone. Journal of Ecology and Protection of the Coastline; 2005, 09
1643-0115
Pojawia się w:
Baltic Coastal Zone. Journal of Ecology and Protection of the Coastline
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Charakterystyka stanu użytkowania małego zbiornika zaporowego Nowaki na Korzkwi
Characteristics of the operational stage of a small dam reservoir Nowaki on the Korzkiew brook
Autorzy:
Wiatkowski, M.
Rosik-Dulewska, C.
Wiatkowska, B.
Powiązania:
https://bibliotekanauki.pl/articles/1819679.pdf
Data publikacji:
2010
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
zbiornik wodny
użytkowanie
piętrzenie wody
zbiornik zaporowy
water tank
Opis:
Zbiorniki wodne, do których należy zbiornik Nowaki, spełniająwiele funkcji ale zawsze poprawiają bilans wodny i mogą być wykorzystywane do różnych celów. Często jednak możliwość wykorzystania retencjonowanej w nich wody zależy od jej jakości [17]. Główną funkcjązbiornika Nowaki jest gromadzenie wody do celów rolniczych (nawodnienia w dolinie rzeki Korzkwi). Ponadto obiekt przeznaczony jest do celów rybackich i rekreacji [10, 19]. Zbiornik Nowaki ze względu na swoje położenie na Przedgórzu Sudeckim, niedaleko od miasta Nysa, jest miejscem atrakcyjnym turystycznie. W związku z tym należy badać stan czystości wody cieku zasilającego zbiornik i wody retencjonowanej w zbiorniku. Zła jakość wody dopływającej do zbiornika może spowodować eutrofizację wody zbiornika i tym samym zmniejszyć walory turystyczne i gospodarcze tego akwenu [21]. W pracy przedstawiono charakterystykę zbiornika zaporowego małej retencji Nowaki na potoku Korzkiew zlokalizowanego w województwie opolskim. Podano i omówiono funkcje zbiornika i spostrzeżenia dotyczące problemów eksploatacyjnych zbiornika. Ponadto przedstawiono wstępne wyniki badań jakości wody dopływającej do zbiornika i z niego odpływającej oraz wody retencjonowanej w zbiorniku. Badania przeprowadzono w 2008 roku. Pracę zakończono wnioskami o potrzebie kontynuowania badań jakości wody i hydrologicznych na terenie zlewni i zbiornika Nowaki.
The paper presents characteristics of a small retention dam reservoir Nowaki on the Korzkiew River, in Opolskie Voivodeship. The Nowaki reservoir is one of 9 small retention dam reservoirs operating in the Opolskie Voivodeship. The reservoir functions were described and some remarks concerning operational problems were presented. Particular attention was paid to the quality of water in the reservoir. Preliminary results of the analyses of the quality of water flowing into the reservoir, outflowing and water stored in the reservoir were discussed. The measurements were carried out in 2008. The performed water quality analyses showed that due to N-NO3 -, N-NH4 +, water temperature, pH, electrolytic conductivity the waters did not exceed the limit values defined for class I. As far as total suspended solids are concerned the exceedence of limit values defined for class II was recorded. It was also observed that the water from the Nowaki reservoir was not euthrophic and sensitive to such pollutants as nitrogen compounds from agricultural sources. The analyses of water from the reservoir showed that among the investigated water quality indicators the most unfavorable conditions for the existence of fish were caused by nitrites and total suspended solids, the values of which exceeded the values defined for fish. Due to the values of total suspended solids the quality of the analyzed water does not meet the requirements defined for water used in inland water basins, either. It was concluded that for the efficient use of the Nowaki reservoir proper agricultural and water-sewage management in the reservoir catchment should be ensured. The paper shows that the present technical state of the reservoir is faultless. The final conclusion is that water quality analyses and hydrological and meteorological measurements in the Korzkiew catchment and the Nowaki reservoir should be continued. This could contribute to the improvement of water management and reduction of unfavorable effects of hydro-meteorological phenomena and potential water pollution.
Źródło:
Rocznik Ochrona Środowiska; 2010, Tom 12; 351-364
1506-218X
Pojawia się w:
Rocznik Ochrona Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena sanitarna wody do picia ze zbiorników okrętowych
Sanitarnaja ocenka pit'evojj vody iz korabel'nyjj bassejjnov
Sanitary evaluation of drinking water in tanks on ships
Autorzy:
Ulewicz, K.
Doboszynski, T.
Powiązania:
https://bibliotekanauki.pl/articles/872041.pdf
Data publikacji:
1958
Wydawca:
Narodowy Instytut Zdrowia Publicznego. Państwowy Zakład Higieny
Tematy:
woda pitna
zbiorniki wodne
okrety
magazynowanie wody
ocena sanitarna
zanieczyszczenia
jakosc wody
drinking water
water tank
ship
water storage
sanitary evaluation
pollution
water quality
Źródło:
Roczniki Państwowego Zakładu Higieny; 1958, 09, 4
0035-7715
Pojawia się w:
Roczniki Państwowego Zakładu Higieny
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of Heavy Metal Content of Pb in Ballast Water Tank of Commercial Vessels in Port of Tanjung Emas Semarang, Central Java Province
Autorzy:
Tjahjono, A.
Bambang, A. N.
Anggoro, S.
Powiązania:
https://bibliotekanauki.pl/articles/123593.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
commercial vessels
ballast water tank
heavy metal content of Pb
Opis:
Heavy metal pollution in the port area had affected aquatic organisms. The research about the heavy metal content of ballast water of commercial vessels, both passenger or cargo vessels, berthing in Port of Tanjung Emas Semarang (PTES), has been conducted by using a method of AAS (Atomic Absorption Spectroscopy). Sample was gathered from vessels berthed in PTES, dated on December 18th 2014 to October 21st 2015. The results of the research show that the mean content of Pb in ballast water tank is 0.37192 mg·l-1. Based on the Decree of Minister of Environment number 51/2004, heavy metal content of Pb in ballast water tank has exceeded the quality standards of port waters.
Źródło:
Journal of Ecological Engineering; 2017, 18, 2; 7-11
2299-8993
Pojawia się w:
Journal of Ecological Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Energy analysis of an air heat pump for hot water
Analiza energetyczna powietrznej pompy ciepla dla CWU
Autorzy:
Szreder, M.
Powiązania:
https://bibliotekanauki.pl/articles/792485.pdf
Data publikacji:
2016
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
energy
heat pump
hot water
operational parameter
condenser
rotary compressor
storage tank
experimental study
Źródło:
Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2016, 16, 1
1641-7739
Pojawia się w:
Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Proposal for water supply systems evaluation due to diversification of water intakes and water tanks
Autorzy:
Rak, J.
Boryczko, K.
Powiązania:
https://bibliotekanauki.pl/articles/95916.pdf
Data publikacji:
2018
Wydawca:
Fundacja Ekonomistów Środowiska i Zasobów Naturalnych
Tematy:
water supply
diversification
water intake
water tank
allocation
zaopatrzenie w wodę
dywersyfikacja
pobór wody
zbiornik wodny
przydział
Opis:
The aim of the study was to compare the various water supply systems – from rural to agglomerations, in terms of continuity of water supply to the inhabitants in a crisis situation. The work included the diversification of water intakes with their number and the maximum daily production capacity and the diversification of water in the water tanks, knowing their number and volume. RB1 and RB2 diversification indexes have been proposed. Assessment criteria were included with comment. The research component is a two-parameter assessment of diversification for selected water supply systems using the indicators proposed by the authors. The use of proprietary indicators to assess the diversification of water supply using preference functions gives the ability to perform calculations easily and accurately.
Źródło:
Ekonomia i Środowisko; 2018, 3; 63-70
0867-8898
Pojawia się w:
Ekonomia i Środowisko
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analiza statyczna cylindrycznego zbiornika żelbetowego na wodę
Autorzy:
Prusiel, Jolanta Anna
Szczech, Marcin
Powiązania:
https://bibliotekanauki.pl/articles/129310.pdf
Data publikacji:
2020
Wydawca:
PWB MEDIA Zdziebłowski
Tematy:
analiza statyczna
zbiornik żelbetowy
zbiornik cylindryczny
zbiornik na wodę
teoria powłok
teoria sprężystości
metoda elementów skończonych
static analysis
reinforced concrete tank
cylindrical tank
water tank
shell theory
elasticity theory
finite element method
Opis:
W artykule przedstawiono wyniki analizy statycznej wpływu przyjętego modelu obliczeniowego na wartości sił wewnętrznych w konstrukcji zbiornika. Do analizy przyjęto monolityczny żelbetowy zbiornik cylindryczny na wodę o średnicy D=6,6 m i wysokości H=6,0 m. Obliczenia statyczne wykonano metodą analityczną (wg teorii powłok i teorii sprężystości) oraz dla trzech modeli obliczeniowych zbiornika z zastosowaniem metody elementów skończonych. Analizowano wpływ podatnego styku w połączeniu ściany z płytą denną i uwzględnienie współpracy konstrukcji zbiornika z podłożem gruntowym. Przeprowadzono analizę porównawczą uzyskanych wartości momentów zginających w płycie dennej oraz momentów południkowych, sił południkowych i równoleżnikowych w cylindrycznej ścianie.
The paper presents results of static analysis of the impact of the adopted computational model on the values of internal forces in a tank structure. A monolithic cylindrical RC water tank of 6.6 m in diameter and 6.0 m in height was used for analysis. Static computations are made using analytical method (according to shell theory and theory of elasticity) and for three tank models the finite element method is used. The impact of elastic contact zone in the connection of the wall with the bottom plate is analysed. Additionally, the model accounts for the interaction of the tank structure with the ground substrate. A comparative analysis of the resulting values of bending moments in the bottom plate as well as vertical moments, vertical and circumferential forces in the cylindrical wall is carried out.
Źródło:
Builder; 2020, 24, 4; 76-79
1896-0642
Pojawia się w:
Builder
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Poziom ogólnej radioaktywności beta i gamma sestonu i perifitonu wybranych zbiorników wodnych
Uroven obshhejj radioaktivnosti beta i gamma sestona i perifitona v izbrannykh vodojomakh
Total beta and gamma radioactivity of seston and perifiton in some water reservoirs
Autorzy:
Pietrzak-Flis, Z.
Powiązania:
https://bibliotekanauki.pl/articles/875554.pdf
Data publikacji:
1963
Wydawca:
Narodowy Instytut Zdrowia Publicznego. Państwowy Zakład Higieny
Tematy:
radioaktywnosc
seston
perifiton
radioizotopy
kumulacja
organizmy wodne
przenikanie
zbiorniki wodne
kontaminacja
pomiary radiometryczne
radioactivity
periphyton
radioisotope
cumulation
aquatic organism
penetration
water tank
contamination
radiometric measurement
Źródło:
Roczniki Państwowego Zakładu Higieny; 1963, 14, 6
0035-7715
Pojawia się w:
Roczniki Państwowego Zakładu Higieny
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wastewater Treatment Methods and Sewage Treatment Facilities in Almaty, Kazakhstan
Autorzy:
Ospanov, Kairat
Kuldeyev, Erzhan
Kenzhaliyev, Bagdaulet
Korotunov, Anatoly
Powiązania:
https://bibliotekanauki.pl/articles/2025747.pdf
Data publikacji:
2021
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
wastewater
sedimentation tank
aeration tank
water quality
wastewater storage
Opis:
The results of comprehensive research on the status of sewage treatment in Almaty are presented in this article. The results of the reconstruction and modernization of treatment facilities intended to improve the sewage treatment efficiency, including the results of pretreatment of wastewater with excess sludge in the primary clarification tank, and the results of hydrobiological and microbiological analysis of activated sludge in the aeration tank are presented. The analysis of the study results of the chemical composition of incoming, clarified and treated wastewater is presented. Besides, the results of the analysis of the water balance of wastewater are presented.
Źródło:
Journal of Ecological Engineering; 2022, 23, 1; 240-251
2299-8993
Pojawia się w:
Journal of Ecological Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experience of Suckling Perfection of Secondary Clarifier of Aeration Station in Almaty, Kazakhstan
Autorzy:
Ospanov, K. T.
Demchenko, A. V.
Kudaiberdi, Z.
Powiązania:
https://bibliotekanauki.pl/articles/123839.pdf
Data publikacji:
2018
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
water disposal
waste water
secondary sedimentation tank
activated sludge
cesspool emptier
sucker
Opis:
This article presents the results of experimental studies pertaining to the suckling improvement of secondary clarifier in an aeration station in Almaty. According to the obtained research results, the work of secondary clarifiers was evaluated for the removal of suspended solids, concentration of returned sludge and sediment moisture. The technical specifications of aerations, secondary settling tanks and cesspool emptier in the aeration station of Almaty were defined. Additionally, it was shown that the use of the articulated sucker with movable scrapers can increase the efficiency of cleaning the bottom of the circular tanks. In this practical test, the proposed suckling radial settler in aeration station of Almaty during the year showed that the sucker reduces the costs for the installation and maintenance of cesspool emptier and has no damaging effects on the bottom of the sump.
Źródło:
Journal of Ecological Engineering; 2018, 19, 5; 210-218
2299-8993
Pojawia się w:
Journal of Ecological Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of excessive solar heat gains on heat loss in the hot water tank – case study
Wpływ nadmiernych uzysków solarnych na straty ciepła z zasobnika cwu – studium przypadku
Autorzy:
Olczak, Piotr
Powiązania:
https://bibliotekanauki.pl/articles/282991.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Instytut Gospodarki Surowcami Mineralnymi i Energią PAN
Tematy:
renewable energy
solar energy
flat plate collector
hot water tank
tank loss coefficient
energia słoneczna
energia odnawialna
płaski kolektor słoneczny
zasobnik ciepłej wody
współczynnik strat ciepła z zasobnika
Opis:
The analysis of a solar installation operation was conducted on the example of a detached house in the Lesser Poland province in Poland. A gas boiler and three flat-plate collectors are located inside the house, which are used for heating water in the hot water tank with a volume of 220 dm3. The installation was established in 2012. The heat measured system (for solar gains) was added in 2014. In 2015–2019 solar heat gains measured per area of absorber were higher than 340 kWh/m2. During a two-week period in June 2015, the insolation on the horizontal plane and the temperature were measured in 4 different points of the hot water tank. On this basis, heat losses from the storage tank were determined, i.e. a decrease in temperature during periods with and without the consumption of hot water by the residents. During this period, a temperature higher than 80°C was observed several times in the hot water tank. In two parts of the hot water tank, rhe determined temperature decreases were used to obtain the heat loss amount. In the analyzed period (2 weeks), 9 days were observed with solar heat gains higher than 9 kWh/day. For these days, the value of heat loss from the solar hot water tank was estimated at over 6 kWh/day. This data corresponds to the actual heat demand for hot water preparation in the building at 7.3 kWh/day. The correlation between daily solar heat gains and solar hot water tank heat losses were also determined. In addition, based on the amount of heat losses, the value of the tank loss coefficient was estimated. The obtained value was compared with the manufacturer’s data and reference data.
Analiza aspektów pracy instalacji solarnej została przeprowadzona na przykładzie domu jednorodzinnego w województwie małopolskim w Polsce. W analizowanym budynku jednorodzinnym znajduje się kocioł gazowy i instalacja solarna złożona z trzech płaskich kolektorów słonecznych. Urządzenia te odpowiadają za przygotowanie ciepłej wody użytkowej magazynowanej w zasobniku o pojemności 210 dm3. Instalacja powstała w 2012 roku, w 2014 roku została opomiarowana pod kątem uzysków solarnych. W latach 2015–2019 mierzono uzyski solarne, były one wyższe niż 340 kWh/m2 powierzchni absorbera. Podczas dwutygodniowego okresu w czerwcu 2015 roku mierzono także natężenie promieniowania słonecznego na płaszczyźnie poziomej i temperaturę w 4 różnych punktach zasobnika ciepłej wody. Na tej podstawie określono straty ciepła z zasobnika, tj. spadek temperatury w zasobniku w okresach z i bez poboru ciepłej wody użytkowej przez mieszkańców. W tym okresie zanotowano temperaturę wyższą niż 80°C w zasobniku tylko przez kilka stosunkowo krótkich okresów. Wyznaczone spadki temperatury w dwóch częściach zasobnika ciepłej wody użytkowej użyto do określenia ilościowych strat ciepła. W analizowanym okresie (2 tygodnie) zaobserwowano 9 dni z uzyskami solarnymi wyższymi niż 9 kWh/dzień. Dla tych dni oszacowano wartości strat ciepła z zasobnika na poziomie powyżej 6 kWh/dzień. Dane te korespondują z rzeczywistym zapotrzebowaniem na ciepło do przygotowania ciepłej wody użytkowej w budynku na poziomie 7,3 kWh/dzień. Określono także zależności między dziennymi uzyskami solarnymi a stratami ciepła z zasobnika (korelacja). Ponadto bazując na wielkościowych stratach ciepła, oszacowano wielkość współczynnika strat ciepła z zasobnika. Uzyskaną wartość porównano z danymi producenta i danymi referencyjnymi.
Źródło:
Polityka Energetyczna; 2020, 23, 2; 91-103
1429-6675
Pojawia się w:
Polityka Energetyczna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Perspektivnye tekhnologicheskie skhemy ochistnykh sooruzhenijj avtomoek
Perspective flowsheets of cleansing buildings of autowashings
Autorzy:
Nikolenko, I.
Demkov, A.
Manujjlov, M.
Powiązania:
https://bibliotekanauki.pl/articles/76833.pdf
Data publikacji:
2013
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
circulation system
filter
pressure flotation
sewage water
contamination
cleaning
horizontal tank
polypropylene
waste water treatment
motor car washing
Opis:
In the article the problems of cleaning of sewages are considered on cleansing buildings of the motor-car washings. The constructions of the known flowsheets of cleaning of sewages of autowashings are analysed. The on principle new flowsheet of cleaning of sewages of autowashings is offered, which leans against financial viability with the maximal diminishing of capital costs and maximal carrying capacity.
Źródło:
Motrol. Motoryzacja i Energetyka Rolnictwa; 2013, 15, 5
1730-8658
Pojawia się w:
Motrol. Motoryzacja i Energetyka Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies