Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "vehicle road tests" wg kryterium: Temat


Tytuł:
Badania przyspieszenia poprzecznego samochodu specjalnego pod kątem wykorzystania w sygnalizatorze niebezpieczeństwa bocznego wywrotu
Lateral acceleration research of special vehicle in terms of application in signaling device of side tipping hazard
Autorzy:
Dzida, J.
Powiązania:
https://bibliotekanauki.pl/articles/157158.pdf
Data publikacji:
2010
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
pomiary przyspieszeń
czujniki przyspieszeń
stateczność poprzeczna pojazdów
acceleration measurements
acceleration sensors
lateral stability of a vehicle
road tests
Opis:
W artykule opisano badania przyspieszeń poprzecznych w różnych punktach pojazdu specjalnego, których celem było wytypowanie miejsc najkorzystniejszych z punktu widzenia działania sygnalizatora niebezpieczeństwa bocznego wywrotu. Skrótowo opisano ideę działania sygnalizatora i zastosowany czujnik przyspieszeń poprzecznych. Przedstawiono przykładowe wyniki badań w postaci przebiegów przyspieszeń poprzecznych z sześciu czujników i wygenerowane wartości sygnałów alarmowych oraz sformułowano wnioski.
Lateral acceleration research in various points of special vehicle, which objective was to designate the most advantageous points in terms of function of signaling device of side tipping hazard is presented in the paper. It briefly presents the idea of function of the signaling device and describes applied lateral acceleration sensor. The examined vehicle features with complex constructional structure with separated detached segments. Under such circumstances it is particularly justified to research lateral acceleration in various vehicle's points. Figure 1 shows chosen placing points of six sensors, three of which are situated in lower part of a frame and the remaining three in upper part of a cabin and body. Figures 2 and 3 present view of a sensor, acquisition and visualization apparatus of measured parameter. The road test during which lateral acceleration was measured is shown in Figures 4 and 5. The results example of lateral acceleration research are shown in Figure 6a and generated values of alarm signals are shown in Figure 6b. The ending part formulates recommendation in regard of choosing lateral acceleration sensors location on the vehicle, with taking into account the criteria of best functionality of signaling device of side tipping hazard.
Źródło:
Pomiary Automatyka Kontrola; 2010, R. 56, nr 3, 3; 233-235
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of the influence of the speed of impact against an obstacle on the dynamic loads acting on occupants of an automotive vehicle with body-on-frame design of the load-bearing structure
Analiza wpływu prędkości uderzenia w przeszkodę na obciążenia dynamiczne osób w samochodzie z ramową konstrukcją nośną
Autorzy:
Prochowski, L.
Żuchowski, A.
Zielonka, K.
Powiązania:
https://bibliotekanauki.pl/articles/1365059.pdf
Data publikacji:
2011
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
bezpieczeństwo transportu
obciążenia dynamiczne pasażerów
samochody osobowo-terenowe
testy zderzeniowe
crash tests
dynamic loads of vehicle occupants
off-road passenger cars
transport safety
Opis:
The dynamic loads acting on a human body during a road accident may cause bodily injuries. The values of such loads measured on test dummies make it possible to predict the effects of the loads on vehicle occupants, with the prediction being based on biomechanical modelling. The dynamic loads were analysed with making use of experimental results of tests where an automotive vehicle came into a head-on collision with an obstacle. In the test vehicle, a Hybrid III test dummy provided with a set of sensors was held with seat belts in the driver's position. By using the experimental results and the determined extreme values of dynamic loads, the dependence of the dynamic loads on the speed of vehicle impact against an obstacle is searched. The knowledge of this dependence will facilitate the prediction of values of dynamic loads and the resulting dangers to the human body that would arise from road accidents. The tests were carried out on an off-road passenger car, where a frame makes a basis of the entire loadbearing structure, i.e. connects all the vehicle components and systems into a self-contained whole and supports the vehicle body. Vehicles with load-bearing structures of this type predominate among those used for military applications. Results of crash tests of such vehicles are rarely published.
Obciążenia dynamiczne, działające na ciało człowieka podczas wypadku drogowego, są źródłem obrażeń. Pomierzone na manekinach wartości tych obciążeń pozwalają, na podstawie modelowania biomechanicznego, na prognozowanie ich skutków dla osób jadących. Analiza obciążeń dynamicznych została przeprowadzona z wykorzystaniem rezultatów badań eksperymentalnych, w których samochód uderza czołowo w przeszkodę. W samochodzie tym manekin Hybrid III z zestawem czujników, przypięty pasami bezpieczeństwa, zajmował pozycję kierowcy. Wykorzystując wyniki badań eksperymentalnych i wyznaczone wartości ekstremalne obciążeń dynamicznych, poszukuje się ich zależności od prędkości uderzenia samochodu w przeszkodę. Poznanie takiej zależności ułatwia prognozowanie wartości obciążeń dynamicznych i powstających zagrożeń dla ciała człowieka w wypadkach drogowych. Badaniom poddano samochód osobowo-terenowy, w którym rama stanowi podstawę układu nośnego, czyli łączy wszystkie zespoły i układy w jedną całość oraz podtrzymuje nadwozie. Samochody o takiej konstrukcji nośnej dominują w zastosowaniach wojskowych. Wyniki ich badań zderzeniowych są rzadko publikowane.
Źródło:
Archiwum Motoryzacji; 2011, 4; 53-73
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Combined control of hydropneumatic springs of the vehicle
Autorzy:
Liashenko, M.
Podzorov, A.
Shekhovtsov, V.
Prytkov, V.
Cherkashina, E.
Powiązania:
https://bibliotekanauki.pl/articles/247202.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
controlled suspension system
ride comfort
hydropneumatic spring
road tests
spatial mathematical model
vehicle
Opis:
The article is devoted to research of a vehicle ride comfort, equipped the suspension system with combined control of springing and damping elements. The spatial mathematical model of a vehicle which meets the requirements of adequacy to real object was developed. The results of the computer simulation of movement of the vehicle with controllable and passive suspension systems on stochastic microprofile are presented. It can be concluded that the spatial multi-mass model is satisfactory close to a real object and can be used for further calculations. Having analyzed simulation results we can state significant increase of ride comfort of a vehicle equipped with a controlled suspension system. Decrease of vertical acceleration of a cabin in a place where a driver sits amounted to 40% in average that can be considered as a limit value for this type of controlled suspension systems. It can be noted that a suspension system with combined control of springing and damping elements can be considered as rather effective in terms of decreasing load of vehicle spring-mounted parts that along with low power consumption makes it rather competitive. The shown research results and control laws for springing and damping elements can be used as a basis for development of relatively simple controlled suspension systems.
Źródło:
Journal of KONES; 2011, 18, 4; 229-234
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparative analysis of frontal zone of deformation in vehicles with self-supporting and framed bodies
Autorzy:
Prochowski, L.
Żółtowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/247110.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
transport
road safety
vehicle safety
crash tests
body deformation range
Opis:
The work considers changes occurred in the features of the supporting structure in three categories of cars, namely: with the self-supporting body, framed body an intermediate structures between these two solutions. The area of analysis includes the length of deformation (crush) of the front al part of the car after collision with a rigid obstacle (barrier). The range of deformation is a significant factor of the passive car safety and indicates the efficiency of fulfilling the protective function for the passengers. The work shows absolute and relative (percentage and unit) variations of the car deformation, depending on the year of manufacture, including the period of 1980 - 2010. Marked trend lines indicated general nature of the deformation range variations together with the improvement of the car supporting system structures. The course of the trend line has been calculated on the basis of average deformation length values, calculated in defined periods of vehicle manufacture. Selected sections of time result from the division of the period of analysis 1980 - 2010 into six parts. The analysis of the deformation length of the frontal part of passenger cars, SUVs and pickups has been combined with simultaneous evaluation of total car length variations and their weight values. The car weight directly affects the kinetic energy of the impact so it has a significant influence on the range of deformation of the car front during collision with an obstacle.
Źródło:
Journal of KONES; 2011, 18, 4; 397-407
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Emisja spalin z wozów bojowych Rosomak w warunkach poligonowych
Exhaust emissions under combat simulating conditions from amv rosomak
Autorzy:
Merkisz, J.
Pielecha, I.
Pielecha, J.
Szukalski, M.
Powiązania:
https://bibliotekanauki.pl/articles/222245.pdf
Data publikacji:
2011
Wydawca:
Akademia Marynarki Wojennej. Wydział Dowodzenia i Operacji Morskich
Tematy:
emisja spalin
badania drogowe
wozy bojowe
exhaust emission
road tests
combat vehicle engines
Opis:
W artykule przedstawiono rezultaty badań silnika spalinowego wozu bojowego — kołowego transportera opancerzonego 8x8 Rosomak w warunkach poligonowych. Do pomiarów wykorzystano mobilny analizator, który umożliwiał pomiar stężenia związków szkodliwych i jednocześnie masowego natężenia spalin. Analizy emisji cząstek stałych dokonano w oparciu o pomiar masy oraz liczbę cząstek stałych. Wykonano pomiary CO, HC, NOx oraz PM i zużycia paliwa w warunkach standardowej jazdy poligonowej, a także w trybie overboost. Na podstawie uzyskanych wyników dokonano analizy warunków pracy silnika i pojazdu, porównano wartości emisji spalin (drogowej i jednostkowej) oraz zużycia paliwa.
The paper presents the results of tests on a combustion engine of an armored modular vehicle 8x8 Rosomak under combat simulating conditions. For the tests a portable exhaust analyzer was used. It measured the concentrations of the exhaust components and the exhaust gas mass flow. The analysis of the PM emission was done based on the measurement of the mass and number of the particles. The measurements of CO, HC, NOx, PM and fuel consumption were performed under the conditions of combat simulation and in the overboost mode. Based on the obtained results an analysis of the engine and vehicle operation was performed and the on-road and unit exhaust emissions as well as on-road and unit fuel consumption were compared.
Źródło:
Zeszyty Naukowe Akademii Marynarki Wojennej; 2011, R. 52 nr 1 (184), 1 (184); 85-90
0860-889X
Pojawia się w:
Zeszyty Naukowe Akademii Marynarki Wojennej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Exploration of the shock-absorber damage influence on the steerability and stability of the car motion
Autorzy:
Parczewski, K.
Powiązania:
https://bibliotekanauki.pl/articles/246042.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
shock absorber
suspension damping coefficient
road tests
vehicle stability
road safety
Opis:
The condition of shock-absorbers is one of factors influencing the in active-safety technology which help drivers to control of their vehicles in the motion. It stuck in the drivers' consciousness, that the damage of the shock-absorber causes the elongation the braking path and the lowering of the drive comfort. The remaining consequences of the worse conditions of shock-absorbers they are not known for the drivers' generality. This impinges on the vehicle motion parameters, its steerability and directional stability. The results of investigations and the analyses of the inefficient shock-absorber influence on vibration damping and the motion of the car were introduced in the presented work. The damping coefficients of the shock-absorber and their change during the exploitation were defined on the basis of test-bed investigations. Road tests were carrying over, on the basis which, try to catch the influence of fault on steerability and the directional stability of the vehicle motion. Road tests were carry over on the A class car. There was compared behaviour of the efficient vehicle and with the worn out shock-absorber. To comparison coefficients various tests are proposed. The road tests were carrying out on A class car with the 4WD driving system, equipped with the drive stability system. Results from individual tests were introduced on graphs.
Źródło:
Journal of KONES; 2011, 18, 3; 331-338
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The analysis of occupant motion in frontal barrier impact of a chassis frame vehicle
Autorzy:
Prochowski, L.
Zielonka, K.
Żuchowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/244471.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
transport
road safety
vehicle safety
crash tests
frontal accidents
occupant kinematic
Opis:
Human body motion during a road accident usually results from the effect of forces of inertia. The analysis of that motion, particularly displacements towards the vehicle interior have significant practical aspect as it facilitates conclusions concerning the mechanisms of danger and injury formation. At the same time, the analysis provides direct indications regarding the improvement of passive safety equipment. The paper presents the time-space diagrams of motion of dummy’s head, neck, torso and hips – the driver of a frame chassis vehicle, identified on the basis of results of the measurements registered in frontal barrier impact and the frame-by-frame analysis of videos recorded during the course of experiment. Courses of these diagrams were associated with acceleration measurement results and forces affecting the parts of the dummy. The experiment showed the complex nature of the influence on the dummy caused by the forces of inertia after a collision of the vehicle with an barrier, vehicle body motion against the frame, reactions in the safety belts, friction on a seat and contact reaction of the vehicle interior equipment. At the same time, it presented the possibilities of indicating the courses of speed variations and dummy displacement as well as significant limitations of calculation possibilities that result from a fact that the process of the impact on the vehicle interior elements is hard to describe.
Źródło:
Journal of KONES; 2011, 18, 1; 491-502
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Risk of injury for the front and rear seat passengers of the passenger cars in frontal impact
Autorzy:
Żuchowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/246867.pdf
Data publikacji:
2012
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
road transport
vehicle safety
crash tests
safety of passengers
rear seat
Opis:
The dynamic loads acting on a human body during a road accident may cause bodily injuries. They are dependent not only on the car structure and applied means of individual protection but also on the anthropometric features of a human body and its location in car. The safety of the car occupants on the rear seats in the passenger cars has been treated as a secondary issue so far. The achieved stage of the structure of that equipment for the rear seat occupants makes an important confirmation of that state. Usually there is no adjustment of the seat belt fixing point position, seat belt pretensioners, seat adjustment. This paper considers the risk of injury for the front and rear seat passengers of the passenger cars on the basis of analysis of dynamic loads that can affect them during the road accident. The attention was paid to the adults and children aged about 10 years. The dynamic loads were analysed with making use of experimental results of frontal flat barrier impact. During the tests, the passengers are protected by typical passive safety systems on the front and the rear seats. In the evaluation used the criteria of the biomechanical human body resistance to the impact load effect. The attention is paid to relations between a seat occupied in a car and the probability of injuries. The analysis of the laboratory impact tests was preceded by the assessment of risk of injury of the front and rear seat passengers in the real road accidents, which has been prepared based on the literature data.
Źródło:
Journal of KONES; 2012, 19, 3; 507-518
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Child safety in a car during a frontal collision
Autorzy:
Żuchowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/241889.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
road transport
vehicle safety
crash tests
child safety
booster seat
Opis:
Road accidents with participation of the children are of particular nature. According to surveys, the older children at the age of 8-12 years are often transported in cars in a wrong way. They are usually fastened with seat belts designed for adult passengers. In order to make the seat belts safe for a child, they should be used together with a booster cushion or a high back booster seat. This paper presents the test results and analysis of dynamic loads affecting a child in the back seat of a passenger car during a frontal collision. The car body was accelerated to a speed of about 48 km/h and then it was suddenly stopped in a time of about 100 ms. The analysis was carried out on the basis of results of experimental tests performed at the collision station in the Automotive Industry Institute in Warsaw. The attention was paid to the influence of protection device type on the P10 dummy, representing a child at the age of about 10 years. Three child protection options during a collision were considered: the dummy was sitting directly in a car seat, on a booster cushion and on a seat. The dummy was fastened with standard seat belts. Evaluation of the protection device influence on the dummy loads was given in association with the operation of the seat belts. During evaluation, the indexes of biomechanical resistance of a human body to the impact load effects were used. They made the basis for the evaluation of the child injury severity risk.
Źródło:
Journal of KONES; 2013, 20, 1; 395-402
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The analysis of the influence of the rear seat passenger position on the kinematics and dynamic loads on a torso and legs during a road accident
Autorzy:
Prochowski, L.,
Żuchowski, A,
Powiązania:
https://bibliotekanauki.pl/articles/245281.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
road transport
vehicle safety
crash tests
safety of passengers
rear seat
Opis:
The analysis carried out by the authors indicates high threat to the rear seat passengers in passenger cars during a road accident. Vehicle designers indicate potential threats for passengers when they take a position in a car which is unexpected by a manufacturer of passive protection systems. Based on that, the tests were prepared in order to consider several different positions of a rear seat passenger. In particular, attention was paid to a threat to passengers when they take a position unexpected by a manufacturer of the passive protection systems in a car. Indicating and justifying a need to adjust the operation of the individual protection means to a passenger anatomy and current passenger position in a car in order to optimize his protection makes an important aim of these tests. This paper presents the results of the tests performed with a Hybrid III dummy, size M50, placed in three different positions in the back seat of a car. During each test, a series of physical values were measured and the motion of a dummy against the car body and the car interior components were filmed. The effects resulting from a change of a passenger’s position, observed on the courses of dynamic loads occurring during an accident, were analysed. Despite of small changes to a passenger’s position, their significant influence on the dummy movement during a frontal collision of a car and an obstacle was observed.
Źródło:
Journal of KONES; 2013, 20, 2; 335-342
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ wybranego przełożenia skrzyni biegów na emisję dwutlenku węgla przez pojazd podczas jego rozpędzania
The impact of the selected gear ratio on carbon dioxide emissions by vehicle during its acceleration
Autorzy:
Merkisz, J.
Andrzejewski, M.
Pielecha, J.
Powiązania:
https://bibliotekanauki.pl/articles/133091.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
badania drogowe
emisja CO2
rozpędzanie pojazdu
dwutlenek węgla
road tests
CO2 emissions
acceleration of vehicle
carbon dioxide
Opis:
W artykule zaprezentowano wyniki pomiarów toksyczności spalin samochodów osobowych w rzeczywistych warunkach ruchu w zależności od wybranego przełożenia skrzyni biegów (możliwego do zastosowania w danych warunkach jazdy), wykonane podczas rozpędzania tych samochodów do określonej prędkości. W oparciu o pozyskane dane pomiarowe dokonano oceny rozpędzania pojazdów uwzględniając minimalną emisję dwutlenku węgla. Rozpatrywanym osobno badaniom w warunkach drogowych poddano 2 samochody osobowe tej samej marki i tego samego modelu: jeden napędzany silnikiem o zapłonie iskrowym, a drugi silnikiem o zapłonie samoczynnym. Testy – rozpędzanie samochodów – wykonywano na pomiarowym odcinku jazdy, stosując różną liczbę biegów w celu osiągnięcia założonej maksymalnej prędkości jazdy. Na podstawie pomiarów i przyjętych kryteriów porównawczych oceniono wpływ rodzaju rozpędzania pojazdów na wielkość emisji dwutlenku węgla.
The article presents the results of measurements of exhaust emissions of cars in real traffic conditions depending on the selected gear (possible to use in the current driving conditions), made during the acceleration of the cars to a certain speed. Based on measured data the acceleration of the vehicles was analyzed, taking into account the minimum carbon dioxide emissions. In the considered separately studies two cars of the same brand and the same model were used: one driven by a spark-ignition engine and one by a compression-ignition engine. The road tests were performed at the measuring segment, using a different number of gears in order to achieve the assumed maximum speed. On the basis of test results and adopted criteria the influence of the style of vehicle acceleration on carbon dioxide emissions was evaluated.
Źródło:
Combustion Engines; 2013, 52, 3; 324-331
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of the driving speed on the exhaust emissions
Wpływ prędkości jazdy samochodem na emisję spalin
Autorzy:
Merkisz, J.
Jacyna, M.
Andrzejewski, M.
Pielecha, J.
Merkisz-Guranowska, A.
Powiązania:
https://bibliotekanauki.pl/articles/133473.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
road tests
exhaust emissions
vehicle speed
badania drogowe
emisja spalin
prędkość jazdy
Opis:
The aim of the study is to verify the thesis about the influence of the vehicle speed on the exhaust emissions. The influence of the speed on the fuel consumption is quite easily measurable and generally possible to identify, while determining the emissions of harmful substances requires specialized research equipment. The analysis is important from the point of view of the vehicle operation. The paper presents the results of the road tests of a car fitted with a diesel engine. It contains the results of measurements of the concentration of the exhaust components. In the measurements, PEMS portable equipment was used. The study was conducted under actual traffic conditions (motorway driving) on a selected portion of the A2 motorway, located near Poznan.
W artykule przedstawiono wyniki badań, których celem było zweryfikowanie tezy o wpływie prędkości jazdy samochodem na emisję spalin. Wpływ prędkości jazdy na przebiegowe zużycie paliwa jest łatwo mierzalny i powszechnie możliwy do określenia, natomiast w celu określenia emisji substancji szkodliwych należy posłużyć się specjalistyczną aparaturą badawczą. Przeprowadzono analizę, która jest istotna z punktu widzenia ekologii eksploatacji pojazdów samochodowych. Zaprezentowano wyniki badań drogowych samochodu osobowego napędzanego silnikiem o zapłonie samoczynnym. Artykuł zawiera także wyniki pomiarów stężenia podstawowych związków szkodliwych emitowanych ze spalinami przez silnik tego pojazdu. W pomiarach wykorzystano mobilną aparaturę do badań toksyczności spalin typu PEMS. Badania przeprowadzono w rzeczywistych warunkach ruchu samochodu (jazda autostradowa) na wybranym fragmencie autostrady A2, zlokalizowanym w rejonach Poznania.
Źródło:
Combustion Engines; 2014, 53, 1; 41-47
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The research of exhaust emissions and fuel consumption from HHD engines under actual traffic conditions
Badania emisji związków toksycznych spalin i zużycia paliwa z silników HDD w warunkach ruchu drogowego
Autorzy:
Merkisz, J
Fuć, P.
Lijewski, P.
Ziółkowski, A.
Rymaniak, Ł.
Powiązania:
https://bibliotekanauki.pl/articles/133609.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
heavy-duty vehicle
exhaust emissions
road tests
pojazd ciężki
emisja gazów wylotowych
badania drogowe
Opis:
The paper presents a comparative analysis of the emission of CO, NOx, CO2 and gas mileage for two heavy-duty long haulage vehicles. The tests were performed on the same test road. The test route reflected typical daily operation of heavy-duty vehicles – a drive to the loading/unloading zone and cruise on national roads. In the investigations, the authors used a portable exhaust emissions analyzer (SEMTECH DS, PEMS – Portable Emissions Measurement System). Based on the performed analysis, optimum engine was selected for long haulage vehicles under conditions of Polish transport and logistic infrastructure in terms of fuel consumption.
W artykule przedstawiono porównanie emisji CO, NOx, CO2 oraz przebiegowego zużycia paliwa dla dwóch pojazdów ciężkich przeznaczonych do długodystansowego przewozu towarów. Badania wykonano na tym samym odcinku pomiarowym. Odzwierciedlał on codzienną eksploatację pojazdów ciężkich – dojazd do miejsca załadunku/rozładunku i ruch po drogach krajowych. Do badań wykorzystano mobilny przyrząd SEMTECH DS z grupy PEMS (Portable Emissions Measurement System). Na podstawie przeprowadzonej analizy określono właściwy wybór silnika spalinowego pojazdu ciężkiego w aspekcie zużycie paliwa dla długodystansowego przewozu towarów w warunkach reprezentujących krajową infrastrukturę transportowo-logistyczną.
Źródło:
Combustion Engines; 2014, 53, 3; 56-63
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania autobusu miejskiego w warunkach jego użytkowania
Research of the city bus in his maintenance conditions
Autorzy:
Koralewski, G.
Wrona, J.
Wrona, R.
Powiązania:
https://bibliotekanauki.pl/articles/317055.pdf
Data publikacji:
2016
Wydawca:
Instytut Naukowo-Wydawniczy "SPATIUM"
Tematy:
autobus miejski
badania drogowe
badania pojazdu
city bus
road tests
vehicle tests
Opis:
Tematyka publikacji dotyczy badań nad możliwościami zwiększenia sprawności układów napędowych pojazdów poprzez analizę teoretyczną zagadnienia oraz badania eksperymentalne. Analizowany problem dotyczy doboru, przydatności i wykorzystania aparatury pomiarowej do badań drogowych pojazdów. Badania dotyczą energochłonności ruchu autobusu miejskiego w rzeczywistych warunkach jego pracy. W wyniku przeprowadzonych wstępnie badań pojazdu otrzymano wykresy charakteryzujące ekonomikę i dynamikę jazdy dla różnych warunków użytkowania. Przeprowadzony zakres badań potwierdził możliwość wykorzystania zestawu badawczego do badań drogowych pojazdu.
The subject of thic publication concerns on the possibilities of increasing the efficiency of vehicles power transmission through theoretical analysis and experimental research issues. The analyzed problem concerns the possibility of using the measuring equipment for testing of road vehicles. Research focuses on the energy consumption of a city bus in real conditions of his work. As a result of the pre-testing of the vehicle was obtained diagrams characterizing the economy and driving dynamics for different conditions.
Źródło:
Autobusy : technika, eksploatacja, systemy transportowe; 2016, 17, 11; 82-84
1509-5878
2450-7725
Pojawia się w:
Autobusy : technika, eksploatacja, systemy transportowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Kształtowanie charakterystyk powstrzymywania pojazdów przez bariery drogowe spełniające kryteria badań zderzeniowych
Shaping the characteristics of the vehicle restraint by road barriers fulfill the criteria of the impact tests
Autorzy:
Fligiel, M.
Powiązania:
https://bibliotekanauki.pl/articles/311285.pdf
Data publikacji:
2017
Wydawca:
Instytut Naukowo-Wydawniczy "SPATIUM"
Tematy:
badania zderzeniowe
energia uderzenia
bariera drogowa
system ograniczający drogę
ASI
THIV
PHD
crash tests
impact energy
road barriers
road restraint system
characteristics of vehicle restraint
Opis:
W pracy rozpatruje się jeden z czynników fizycznych (przyspieszenie, opóźnienie) wpływających w znacznym stopniu na utratę zdrowia pasażerów pojazdów samochodowych. Przedstawiono metodę obniżenia poziomu przyspieszeń, poprzez zastosowanie w barierach o małej podatności układu sprężystego akumulującego energię uderzenia pojazdu, a tym samym obniżenia przyspieszenia (opóźnienia). W przedstawionej metodzie uwzględnia się zalecenia dotyczące poziomu powstrzymywania barier spełniających kryteria badań zderzeniowych.
The subject of the publication concerns the analysis of stages of vehicle body deformation in frontal collision for the characteristics of delay, speed and deformation of the vehicle. The course of the collision was divided into stages, whose boundaries are determined by the characteristic intervals.. In the work one of the physical factors (acceleration or delay), which influence significantly on the loss of the health of passengers vehicles, is considered. A method of reducing the level of acceleration is presented. In the barriers with low system compliance is used an accumulating elastic energy system of the vehicle impact and thereby reduced acceleration (delay). In the presented method, the recommendations on the containment level barriers to meet the criteria of the impact tests are taken into account.
Źródło:
Autobusy : technika, eksploatacja, systemy transportowe; 2017, 18, 7-8; 175-180
1509-5878
2450-7725
Pojawia się w:
Autobusy : technika, eksploatacja, systemy transportowe
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies