Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "vacuum induction furnace" wg kryterium: Temat


Wyświetlanie 1-8 z 8
Tytuł:
Effects of Pressure on the Rate of Tin Evaporation From Liquid Iron
Wpływ ciśnienia na szybkość parowania cyny z ciekłego żelaza
Autorzy:
Lipart, J.
Łabaj, J.
Słowikowski, M.
Jama, D.
Powiązania:
https://bibliotekanauki.pl/articles/352625.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
liquid iron
evaporation
vacuum induction furnace
mass transfer coefficient
ciekłe żelazo
parowanie
próżniowy piec indukcyjny
współczynnik przenikania masy
Opis:
In the paper, tin elimination from liquid iron alloy via low-pressure evaporation has been analysed. The experiments were performed using a single-chamber VIM 20-50 vacuum induction furnace at 1923 K and the operating pressure of 0.05 to 557 Pa.
W prezentowanej pracy dokonano analizy procesu eliminacji cyny z ciekłego stopu żelaza na drodze odparowania w warunkach obniżonego ciśnienia. Eksperymenty realizowano w jednokomorowym indukcyjnym piecu próżniowym V1M 20-50 w temperaturze 1923 K i zakresie ciśnień roboczych od 0.05 do 557 Pa.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 2; 825-828
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Elimination of Zinc from Aluminum During Remelting in an Vacuum Induction Furnace
Autorzy:
Smalcerz, Albert
Blacha, Leszek
Węcki, Bartosz
Desisa, D. G.
Łabaj, Jerzy
Jodkowski, Maciej
Powiązania:
https://bibliotekanauki.pl/articles/2174631.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
mass transfer coefficient
zinc evaporation
vacuum induction furnace
meniscus
współczynnik przenikania masy
odparowanie cynku
piec indukcyjny próżniowy
menisk
Opis:
In this paper, the results of the study on aluminium evaporation from the Al-Zn alloys (4.2% weight) during remelting in a vacuum induction furnace (VIM) are presented. The evaporation of components of liquid metal alloys is complex due to its heterogeneous nature. Apart from chemical affinity, its speed is determined by the phenomena of mass transport, both in the liquid and gas phase. The experiments were performed at 10-1000 Pa for 953 K - 1103 K. A significant degree of zinc loss has been demonstrated during the analysed process. The relative values of zinc loss ranged from 4 to 92%. Lowering the pressure in the melting system from 1000 Pa to 10 Pa caused an increase in the value of density of the zinc evaporating stream from 3.8210-5 to 0.000564 gcm-2s-1 at 953 K and 3.3210-5 to 0.000421 gcm-2s-1 for 1103 K. Based on the results of the conducted experiments. it was found that evaporation of zinc was largely controlled by mass transfer in the gas phase and only for pressure 10 Pa this process was controlled by combination of both liquid and gas phase mass transfer.
Źródło:
Archives of Foundry Engineering; 2022, 22, 3; 11--18
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of the Power of Various Types of Induction Furnaces on the Shape of the Metal Bath Surface
Autorzy:
Smalcerz, Albert
Węcki, Bartosz
Blacha, Leszek
Powiązania:
https://bibliotekanauki.pl/articles/2123294.pdf
Data publikacji:
2021
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
induction vacuum furnace
Al-Zn alloys
cold crucible furnace
metal bath surface
Opis:
The work shows the results of examinations conducted to ascertain the influence of the working power of a vacuum induction crucible furnace (ICF) and a furnace with a cold crucible(CCF), on the surface area of liquid Al-Zn alloy molten within these devices. It was determined that the increase of the value of this parameter causes the increase of the liquid alloys surface area. In the case of smelting alloy inside a crucible furnace the increase of power from 8 to 22 kW causes the increase of liquid alloy surface from 88 to 155 cm2. For a furnace with a cold crucible, the power increase from 70 to 130 kW causes the increase of the alloy surface from 280 to 330,3 cm2. For all power values a larger increase in surface area was observed in crucible furnaces (around two times). In cases of cold crucible furnaces, this increase was around 20%. Additionally, based on the examination results the way in which the surface area of liquid alloy can intensify the undesirable process of zinc fuming away, was discussed. It has been demonstrated that the process of zinc elimination from the examined alloy is more intensive while using a cold crucible induction furnace.
Źródło:
Advances in Science and Technology. Research Journal; 2021, 15, 3; 34--42
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Aluminium loss during Ti-Al-X alloy smelting using the VIM Technology
Autorzy:
Smalcerz, A.
Blacha, L.
Łabaj, J.
Powiązania:
https://bibliotekanauki.pl/articles/1837853.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
melting of Ti-Al alloys
induction vacuum furnace
evaporation of metals
Opis:
Titanium alloys belonging to the group of modern metallic materials used in many industries, including the aerospace industries. Induction crucible vacuum furnaces and induction furnaces with cold crucible are most commonly used for their smelting. When operating these devices, one can deal with an adverse phenomenon of decrease in the content of alloy elements that are characterized by higher equilibrium vapour pressure than the matrix metal or titanium, in the metal bath. In the paper, results of the study on aluminium evaporation from the Ti-Al-Nb, Ti-Al-V and Ti-Al alloys (max 6.2 % wt.) during smelting in a vacuum induction melting (VIM) furnace are presented. The experiments were performed at 10 to 1000 Pa for 1973 K and 2023 K. A significant degree of aluminium loss has been demonstrated during the analysed process. The values of relative aluminium loss for all the alloys ranged from 4 % to 25 %. Lowering the pressure in the melting system from 1000 Pa to 10 Pa resulted in increased values of aluminium evaporation flux from 4.82⋅10-5 to 0.000327 g⋅cm-2⋅s-1 for 1973 K and from 9.28⋅10-5 to 0.000344 g⋅cm-2⋅s-1 for 2023 K. The analysis of the results obtained took into account the value of the actual surface of the liquid metal. In the case of melting metals in an induction furnace, this surface depends on the value of power emitted in the charge. At greater power, we observe a significant increase in the bath surface due to the formation of a meniscus.
Źródło:
Archives of Foundry Engineering; 2021, 21, 1; 11-17
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Contribution to Deoxidation of Austenitic Steels in a Vacuum Induction Furnace with Carbon
Autorzy:
Šenberger, J.
Pernica, V.
Powiązania:
https://bibliotekanauki.pl/articles/379906.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
vacuum induction furnace
deoxidation
carbon
austenitic steel
petrochemistry
oxygen activity
total oxygen
próżniowy piec indukcyjny
odtlenianie
węgiel
staliwo austenityczne
petrochemia
aktywność tlenu
Opis:
Deoxidation of steel with carbon under reduced pressure is often used for increasing the steel purity. Suitable units for this purpose in foundries are vacuum induction furnaces. Possibilities of increasing the steel purity by deoxidation with carbon in the vacuum induction furnace were studied for the steel for the petrochemistry of specific composition 25Cr/35Ni. The charge composed of the return material only was melted in the air. During melting the charge oxidized and the oxidizing slag formed. Chemical composition of steel, morphology, chemical composition of inclusions in the steel and chemical composition of slag after vacuuming were studied on the basis of samples taken before and after vacuuming. Temperature and oxygen activity were measured before and after vacuuming. Globular inclusions with dominant content of silicon and manganese were observed in steel before and after vacuuming. Contents of total oxygen in steel didn’t change significantly during vacuuming. On the basis of composition of inclusions and measured oxygen activity the activity of Cr2O3 in inclusions was calculated. A slag sample was taken after vacuuming and equilibrium oxygen activity in steel with regard to the Cr2O3 content in the slag was estimated from the slag composition. Equilibrium oxygen activity in relation to the Cr2O3 content in the slag was higher than equilibrium activity measured in the steel. For this reason it is not possible, under the studied conditions, to decrease oxygen content in steel during vacuuming.
Źródło:
Archives of Foundry Engineering; 2015, 15, 2; 105-109
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wytapianie i odlewanie w próżniowym piecu indukcyjnym wlewków stalowych przeznaczonych na materiał badawczy do symulacji fizycznych w skali półprzemysłowej
Melting and casting in vacuum induction furnace of steel ingots used as stock material for physical simulations in semi-industrial scale
Autorzy:
Bulkowski, L.
Galisz, U.
Pogorzałek, J.
Stecko, J.
Mazur, A.
Gawor, J.
Powiązania:
https://bibliotekanauki.pl/articles/182458.pdf
Data publikacji:
2012
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Metalurgii Żelaza im. Stanisława Staszica
Tematy:
próżniowy piec indukcyjny
wysokowęglowa średniostopowa stal bainityczna
makrosegregacja wlewka
charakterystyki wysokotemperaturowe
vacuum induction furnace
high carbon medium-alloyed bainitic steel
ingot macrosegregation
high-temperature characteristics
Opis:
Opracowano technologie i wykonano w próżniowym piecu indukcyjnym VSG 100 wytopy doświadczalne stali o wymaganej superczystości metalurgicznej, obejmujące następujące grupy stali: stale konstrukcyjne mikrostopowe o strukturze superdrobnoziarnistej, stale konstrukcyjne o strukturze wielofazowej i wysokowęglowe, średniostopowe stale bainityczne. Wytopy odlewano do krystalizatorów miedzianych chłodzonych wodą oraz do wlewnic żeliwnych z nadstawkami, o zróżnicowanych wymiarach i masach wlewka. Przeprowadzono badania wpływu parametrów odlewania oraz warunków krzepnięcia wlewka wysokowęglowej średniostopowej stali bainitycznej odlanego do konwencjonalnej wlewnicy żeliwnej o przekroju płaskim na makrosegregacje pierwiastków. Wykonano badania makrosegregacji strefowej pierwiastków we wlewku oraz wyznaczono charakterystyki wysokotemperaturowe stali.
The experimental heats of required metallurgical super-cleanness were carried out in vacuum induction furnace VSG 100 according to the developed technology. The following steel groups were melted and casted: microalloyed structural steels with super fi ne-grained structure, structural steels with multiphase structure and high carbon medium-alloyed bainitic steels. Heats were casted into water-cooled copper mould and into cast iron hottopped mould to produce ingots with diverse dimensions and weights. The investigation of influence of casting parameters and solidification conditions of high carbon medium-alloyed bainitic steel ingots casted into a fl at cast iron mould, on macrosegregation of the elements was carried out. The research of zonal macrosegregation of the elements in ingots was carried out and high-temperature characteristics of steels were determined.
Źródło:
Prace Instytutu Metalurgii Żelaza; 2012, T. 64, nr 1, 1; 118-128
0137-9941
Pojawia się w:
Prace Instytutu Metalurgii Żelaza
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Aluminium loss during Ti-Al-X alloy smelting using the VIM Technology
Autorzy:
Smalcerz, Albert
Blacha, L.
Łabaj, J.
Powiązania:
https://bibliotekanauki.pl/articles/1837812.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
melting of Ti-Al alloys
induction vacuum furnace
evaporation of metals
stopy Ti-Al
indukcyjny piec próżniowy
odparowanie
Opis:
Titanium alloys belonging to the group of modern metallic materials used in many industries, including the aerospace industries. Induction crucible vacuum furnaces and induction furnaces with cold crucible are most commonly used for their smelting. When operating these devices, one can deal with an adverse phenomenon of decrease in the content of alloy elements that are characterized by higher equilibrium vapour pressure than the matrix metal or titanium, in the metal bath. In the paper, results of the study on aluminium evaporation from the Ti-Al-Nb, Ti-Al-V and Ti-Al alloys (max 6.2 % wt.) during smelting in a vacuum induction melting (VIM) furnace are presented. The experiments were performed at 10 to 1000 Pa for 1973 K and 2023 K. A significant degree of aluminium loss has been demonstrated during the analysed process. The values of relative aluminium loss for all the alloys ranged from 4 % to 25 %. Lowering the pressure in the melting system from 1000 Pa to 10 Pa resulted in increased values of aluminium evaporation flux from 4.82⋅10-5 to 0.000327 g⋅cm-2⋅s-1 for 1973 K and from 9.28⋅10-5 to 0.000344 g⋅cm-2⋅s-1 for 2023 K. The analysis of the results obtained took into account the value of the actual surface of the liquid metal. In the case of melting metals in an induction furnace, this surface depends on the value of power emitted in the charge. At greater power, we observe a significant increase in the bath surface due to the formation of a meniscus.
Źródło:
Archives of Foundry Engineering; 2021, 21, 1; 11-17
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Removal of Lead From Blister Copper by Melting in the Induction Vacuum Furnace
Autorzy:
Smalcerz, A.
Blacha, L.
Powiązania:
https://bibliotekanauki.pl/articles/946871.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
removal of lead
vapour pressure
blister copper
induction vacuum furnace
evaporation of metals
refining of cooper
usuwanie ołowiu
miedź konwertorowa
indukcyjny piec próżniowy
topienie
rafinacja
Opis:
The usage of the reduced pressure in the processes of smelting and refining of metal alloys allow to remove not only the gases dissolved in the metal bath, but also the impurities having a higher vapour pressure than the matrix metal. Blister copper produced in flash furnace contains many impurities such as lead, bismuth and arsenic. Some of them must be removed from molten metals, because of their deleterious effects on copper electrical properties. When the smelting process is carried out in the induction vacuum furnaces, the above-mentioned phenomenon is being intensified, one or another mixing of bath and increase in the surface area of mass exchange (liquid metal surface). The latter results from the formation of a meniscus being an effect of the electromagnetic field influence on the liquid metal. In the work, the results of refining blister copper in terms of removing lead from it, are presented. The experiments were carried out in the induction crucible vacuum furnace at temperatures of 1473 and 1523 K, and operating pressures in a range of 8 - 533 Pa.
Źródło:
Archives of Foundry Engineering; 2020, 20, 2; 84-88
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-8 z 8

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies