Temat: turning dynamometer - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: The influence of changing of cutting parameters on temperature and cutting forces during turning process of stainless steel with CCET09T302R-MF insert
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/243223.pdf
Data publikacji:: 2017
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
temperature
cutting forces
stainless steel
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of change of cutting parameters on temperature and cutting forces during turning process of stainless steel. A shaft made of 304L stainless steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 centre lathes. Measurement of cutting forces during lathing process used DKM 2010 turning dynamometer. The turning process was conducted by a cutting tool with CCET09T302R-MF insert by DIJET. During the turning, the following machining parameters were used: cutting speed Vc = 226 m/min, feed f = 0.044, 0.062, 0.083, 0.106 mm/rev and cutting depth ap = 0.25, 0.5, 0.75, 1.0 mm. The chemical composition of steel was measured by Solaris-ccd plus optical spectrometer.
Źródło:: Journal of KONES; 2017, 24, 4; 133-140
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: The influence of treatment conditions on cutting forces and surface roughness
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/241665.pdf
Data publikacji:: 2016
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
surface roughness parameter
stainless steel
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of treatment conditions during turning of shafts on the cutting forces and surface roughness parameter. A roller made of S235JR steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 and CU500MRD centre lathes. Measurement of cutting forces during lathing process used DKM 2010 and Kistler turning dynamometers. The turning process was conducted by a cutting tool with CCMT09T304 PF removable plate. During the turning, the following machining parameters were used: cutting speed Vc = 150 m/min, feed f=0.106 mm/rev and cutting depth ap = 0.5, 0.75, 1.0, 1.25, 1.5, 1.75 mm. The surface roughness was measured by T8000 profilometer.
Źródło:: Journal of KONES; 2016, 23, 1; 207-213
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Finishing treatment of marine pump shafts made of X5CRNI18-10 steel
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/244602.pdf
Data publikacji:: 2018
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
temperature
cutting forces
stainless steel
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of cutting parameters change on temperature and cutting forces during turning process of stainless steel. A shaft made of 304L stainless steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 centre lathe. Measurement of cutting forces during lathing process used DKM 2010 turning dynamometer. The turning process was conducted by a cutting tool with CCET09T302R-MF insert by DIJET. During the turning, the following machining parameters were used: cutting speed Vc = 152, 219, 304 m/min, feed f = 0.044, 0.062, 0.083 mm/rev and cutting depth ap = 0.4, 0.8, 1.2, 1.6 mm. The view of the nose radius of cutting tool before and after the turning process was made by the Smartzoom 5 microscope.
Źródło:: Journal of KONES; 2018, 25, 2; 215-222
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: The influence of cutting parameters on cutting forces and surface roughness
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/246880.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
cutting forces
cutting temperature
surface roughness
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the preliminary research results referring to the analysis of the influence of finishing lathing on the cutting forces and surface roughness of steel. The research was performed on a roller 39 mm in diameter made of S235JR steel. The finish tooling of pump shaft pins was carrying out on a universal centre lathe. The finish lathing process was carried out by means of a CCMT 09T304 PF Sandvik Coromant cutting tool with replaceable inserts. During the research, the effect of changes in the depth of cut on the value of cutting forces and temperature was defined. In addition, the influence of the depth of cut on the surface roughness was determined.
Źródło:: Journal of KONES; 2014, 21, 3; 199-204
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: The influence of changing the side angle of the cutting tool by wiper technology on the value of material ratio parameters of steel applied to marine pump shaft pins
Autorzy:: Labuda, W.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/244335.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
surface roughness
material ratio
stainless steal
Opis:: Angular momentum pumps are very often used in cooling circuits of medium and high power engines, power plant boilers as well as bilge, ballast and firefighting installations. Such an extensive use of angular momentum pumps on board is connected with their numerous advantages. However, during operation the wear of marine hull, the rotor and shaft seals take place. The research attempts to increase the service life of shafts. The article presents the research results of pump shaft pins after finish lathing. The research was performed on a roller 60 mm in diameter made of X5CrNi18-10 steel. The finish tooling of pump shaft pins was carried out on a universal CDS 6250 BX-1000 centre lathe. The finish lathing process was carried out by means of Sandvik Coromant cutting tool with replaceable inserts. In the research of lathing, process used inserts with Wiper technology. During the lathing, the optimal cutting parameters were used for inserts: CCMT09T302WF, CCMT09T304WF and CCMT09T308WF. The cutting process was performed at side angle of 90° ± 3°. The process of lathing used cutting tool dynamometer DKM 2010. During the research, the effect of cutting tool geometric on surface roughness parameter Ra of steel applied to marine pumps shaft pins was determined. The article presents the research results of material ratio parameters. In addition provides an examples shaft surface profile analysis and material ratio. Measurement of surface roughness and material ratio parameters was performed by T8000 profilometer.
Źródło:: Journal of KONES; 2015, 22, 2; 139-147
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 6.

Tytuł:: The analysis of cutting tool geometric on cutting forces and surface roughness of steel applied to marine pumps shaft pins
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/246319.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
cutting forces
cutting temperature
surface roughness
stainless steal
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the research results referring to the analysis of the influence of finishing lathing on the cutting forces and surface roughness of stainless steel. The research was performed on a roller 60 mm in diameter made of X5CrNi18-10 steel. The finish tooling of pump shaft pins was carry out on a universal CDS 6250 BX-1000 centre lathe. The finish lathing process was carried out by means of Sandvik Coromant cutting tool with replaceable inserts. During the research, the effect of cutting tool geometric on cutting forces and surface roughness of steel applied to marine pumps shaft pins ware tested. In addition, the influence of cutting tool geometric on cutting temperatures was determined.
Źródło:: Journal of KONES; 2014, 21, 1; 147-152
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 7.

Tytuł:: The influence of cutting inserts geometric on surface roughness of steel applied to sea water pump shafts
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/244988.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
surface roughness parameters
stainless steel
marine pump shaft
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the research results of pump shaft pins finish turning. The research was performed on a roller 60 mm in diameter made of X5CrNi18-10 steel. The finish tooling of pump shaft pins was carry out on a universal CDS 6250 BX-1000 centre lathe. The finish lathing process was carried out by means of Sandvik Coromant cutting tool with replaceable inserts. In the research of lathing process used standard inserts (MF), inserts with increased tolerance (UM) and inserts with Wiper technology (WF). During lathing, the optimal machining parameters were used. The cutting process was performed at entering angle of 90°. The process of lathing used cutting tool dynamometer DKM 2010. During the research, the effect of cutting insert geometric and optimal cutting parameters on the surface roughness of steel applied to marine pumps shaft pins was determined.
Źródło:: Journal of KONES; 2015, 22, 3; 133-140
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 8.

Tytuł:: The influence of changing of cutting parameters on temperature and cutting forces during turning process by CCET09T302R-MF insert
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/241601.pdf
Data publikacji:: 2018
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
temperature
cutting forces
cutting parameters
stainless steel
dynamometr
temperatura
siły skrawania
parametry cięcia
stal nierdzewna
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of change of cutting parameters on temperature and cutting forces during turning process of stainless steel. A shaft made of 304L stainless steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 centre lathes. Measurement of cutting forces during turning process used DKM 2010 turning dynamometer. A cutting tool conducted the turning process with CCET09T302R-MF insert by DIJET. During the turning, the following machining parameters were used: cutting speed Vc = 226 m/min, feed f = 0.044; 0.062; 0.083; 0.106 mm/rev and cutting depth ap = 0.375; 0.625; 0.875 mm. The chemical composition of steel was measured by Solaris-ccd plus optical spectrometer. The Smartzoom 5 microscope made the view of the nose radius of cutting tool.
Źródło:: Journal of KONES; 2018, 25, 1; 249-256
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 9.

Tytuł:: Monitorowanie sił skrawania podczas toczenia
Monitoring of cutting forces during turning
Autorzy:: Nosol, A.
Bartoszuk, M.
Powiązania:: https://bibliotekanauki.pl/articles/404591.pdf
Data publikacji:: 2018
Wydawca:: Wydawnictwo AWART
Tematy:: toczenie
siła skrawania
składowe siły skrawania
siłomierz
pomiar siły
turning
cutting force
cutting force components
dynamometer
force measurement
Opis:: It is well known that machining is the basic technique for manufacturing machine parts. Over the years, the machining processes have intensified, and what is more, the machining of difficult-to-cut materials, such as nickel and titanium alloys, has become more and more popular. For this reason, the process of cutting is not fully understood. Therefore, knowledge of the distribution of cutting forces and phenomena occurring in the cutting zone allows, for example, for optimization of cutting parameters and monitoring of tool wear. In the literature, the measuring devices for the total cutting force components were rarely described. For this reason, the authors have decided to explore the subject in greater depth. This article presents examples of constructions of turning actuators and comparison of results obtained for strain gauges of own design and professional piezoelectric actuator for the same machining parameters.
Powszechnie wiadomo, że obróbka skrawaniem jest podstawową techniką wytwarzania części maszyn. Z biegiem lat zauważalna jest intensyfikacja procesów obróbki, co więcej – coraz częściej obrabiane są materiały trudnoskrawalne, np. stopy niklu i tytanu. Z tego powodu proces ich skrawania nie do końca jest poznany. Znajomość rozkładu sił skrawania i zjawisk występujących w strefie skrawania pozwala np. na optymalizację parametrów skrawania oraz na monitorowanie zużycia narzędzia. W literaturze fachowej urządzenia do pomiaru składowych całkowitej siły skrawania były rzadko opisywane. Z tego powodu autorzy postanowili zgłębić ten temat. Artykuł niniejszy przedstawia przykładowe konstrukcje siłomierzy tokarskich oraz porównanie wyników uzyskanych dla siłomierzy tensometrycznych własnej konstrukcji i profesjonalnego siłomierza piezoelektrycznego dla tych samych parametrów obróbki.
Źródło:: Obróbka Metalu; 2018, 3; 30-35
2081-7002
Pojawia się w:: Obróbka Metalu
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "turning dynamometer" wg kryterium: Temat

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język