Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "physical modelling" wg kryterium: Temat


Tytuł:
Similarity and model designing in a nonscalar description of an examined process
Podobieństwo i projektowanie modeli dla procesów zależnych od nieskalarnych zmiennych
Autorzy:
Kasprzak, W. A.
Powiązania:
https://bibliotekanauki.pl/articles/279230.pdf
Data publikacji:
2003
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
similarity
dimensional analysis
physical modelling
Opis:
The problem of similarity and designing of a physical model of an examined process is considered on the basis of generalizations of Theorem ... . It is shown that in cases of nonscalar description the similar model of a process could be designed on the basis a special version of Theorem ... . Similarity scales can be obtained only for the vector modulus, or for the components of vectors and tensors when special experimental condotions (described in this paper) are fulfilled.
Znana z literatury teoria podobieństwa modelowego i algorytmy projektowania modeli opracowano przy założeniu, że proces zależy od zmiennych, które są skalarami. W pracy podaje się rozwiązanie tych problemów dla nieskalarnych zmiennych, od których zależy przebieg procesu. Podaje się odpowiednią wersję twirdzenia ... dla funkcji wymiarowych zależnych od zmiennych, które mogą być tensorami i sposób wyznaczania skal. Pokazuje się, że otrzymuje się takie same rezultaty, jak dla modeli skalarnych, ale otrzymuje się pełną informację o składowych tensora opisującego badany proces, a więc pełne informacje pozwalające na opracowanie projektu badań empirycznych (nie otrzymywano ich w tradycyjnym modelu).
Źródło:
Journal of Theoretical and Applied Mechanics; 2003, 41, 2; 383-394
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Parameters of Argon Purging Process Through Ladle on the Phenomena Occuring in the Area of Phase Distributions: Liquid Steal-Slag
Autorzy:
Pieprzyca, J.
Merder, T.
Saternus, M.
Gryc, K.
Socha, L.
Powiązania:
https://bibliotekanauki.pl/articles/356927.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
steelmaking
ladle
slag
physical modelling
Opis:
Purging the liquid steel with inert gases is a commonly used treatment in secondary metallurgy. The main purposes for which this method is used are: homogenization of liquid steel in the entire volume of the ladle, improvement of mixing conditions, acceleration of the absorption process of alloy additives and refining of liquid steel from non-metallic inclusions. The basic processing parameters of this treatment are: gas flow rate and the level of gas dispersion in liquid steel. The level of gas dispersion depends on the design and location of the porous plug in the ladle. Therefore, these parameters have a significant impact on the phenomena occurring in the contact zone of liquid steel with slag. Their improper selection may cause secondary contamination of the bath with exogenous inclusions from the slag, or air atmosphere due to discontinuity of the slag and exposure of the excessive surface of the liquid steel free surface. The article presents the results of modelling research of the effect of liquid steel purging with inert gases on phenomena occurring in this zone. The research was carried out using the physical (water) model of steel ladle. As a modelling liquid representing slag, paraffin oil was used, taking into account the conditions of similarity with particular reference to the kinematic viscosity. The results of the conducted research were presented in the form of visualization of phenomena occurring on the surface of the model liquid free surface in the form of photographs. The work is a part of a bigger study concerning modelling of ladle processes.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 2; 653-658
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical Analysis of the Structure of Liquid Flow in the Tundish with Physical Model Verification
Autorzy:
Merder, T.
Powiązania:
https://bibliotekanauki.pl/articles/352430.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
steelmaking
continuous casting
tundish
numerical modelling
physical modelling
Opis:
Detailed studies of the movement of liquid steel (hydrodynamics) on a real object are practically impossible. The solution to this problem are physical modelling carried out on water models and numerical modelling using appropriate programs. The method of numerical modelling thanks to the considerable computing power of modern computers gives the possibility of solving very complex problems. The paper presents the results of model tests of liquid flow through tundish. The examined object was model of the twonozzle tundish model. The ANSYS Fluent program was used to describe the behavior of liquid in the working area of the tundish model. Numerical simulations were carried out using two numerical methods of turbulence description: RANS (Reynolds-Averaged Navier-Stokes) – model k-ε and LES (Large Eddy Simulation). The results obtained from CFD calculations were compared with the results obtained using the water model.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 4; 1895-1901
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Physical Model of the Nonlinear Sitar String
Autorzy:
Siddiq, S.
Powiązania:
https://bibliotekanauki.pl/articles/177221.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
sitar
physical modelling
nonlinear string vibration
dispersion
Opis:
The acoustic properties of the sitar string are studied with the aid of a physical model. The nonlinearity of the string movement caused by the bridge acting as an obstacle to the vibrating string is of special interest. Comparison of the model’s audio output to recordings of the instrument shows interesting similarities. The effects dispersion and bridge have on the sound of the instrument are demonstrated in the model.
Źródło:
Archives of Acoustics; 2012, 37, 1; 73-79
0137-5075
Pojawia się w:
Archives of Acoustics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Determination of RTD Curves for Aluminium Refining Process Conducted in Batch Reactor – Physical Modelling
Autorzy:
Saternus, M.
Powiązania:
https://bibliotekanauki.pl/articles/354307.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminium refining
barbotage
physical modelling
RTD curves
Opis:
It is really hard to determine the phenomena occurring during aluminum refining process using argon blowing through the liquid metal in industrial conditions. The solution of such problem is physical modelling. This kind of modelling gives possibility to determine the level of dispersion of the refining gas in liquid metal. Especially in steel metallurgy RTD (Residence Time Distribution) analysis and visualization process with some colour tracer, which can give extra information about time of mixing are very popularly used. Because the modelling research (especially visualization) is pictorial, the research was conducted to check if it is possible to estimate quantitatively impeller working effectiveness basing on determination of the RTD curves. The examined object was model of URO-200 batch refining reactor. The RTD curves was registered and discussed for three different impellers and four different variants of processing parameters (rotary impeller speed: 300-500 rpm, and gas flow rate: 15-20 l·min-1). Additionally, the process of mixing of the inert gas with water as a modelling agent was enabled to be observed due to introduction of colour tracer (KMnO4). Results obtained from both measuring methods were graphically presented, compared and shortly discussed.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 4; 1909-1914
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study of Tundish Slag Entrainment Using Physical Modelling
Autorzy:
Michalek, K.
Gryc, K.
Socha, L.
Saternus, M.
Tkadlečková, M.
Pieprzyca, J.
Merder, T.
Pindor, L.
Powiązania:
https://bibliotekanauki.pl/articles/353001.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
steelmaking
tundish
slag entrainment
vortex
physical modelling
Opis:
This paper deals with the possibilities of using physical modelling to study the slag entrainment in the tundish. A level of steel in the tundish is changing during sequential continuous casting. The most significant decrease in the steel level occurs when replacing ladles. It is generally known that if the height of steel level in the tundish drops below a certain critical level, it may generate vortexes over the nozzles and as a consequence entrainment of tundish slag into individual casting strands can occur. Thus, it is necessary to identify the critical level of steel for specific operational conditions. In this paper, the development of physical modelling methodology is described as well as physical model corresponding to operational continuous casting machine No. 2 in Třinecké železárny, a.s. The obtained results are discussed.
Źródło:
Archives of Metallurgy and Materials; 2016, 61, 1; 257-260
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental Methods of Validation for Numerical Simulation Results on Steel Flow through Tundish
Autorzy:
Pieprzyca, J.
Warzecha, P.
Merder, T.
Warzecha, M.
Powiązania:
https://bibliotekanauki.pl/articles/355968.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
continuous casting
tundish
physical modelling
numerical modeling
Opis:
The article presents experimental results on the impact of tundish flow regulator influencing the liquid steel flow course. The research was conducted based on the hybrid modelling methods understood as a complementary use of Computational Fluid Dynamics (CFD) methods and physical modelling. Dynamic development of numerical simulation techniques and accessibility to highly advanced and specialized software causes the fact that these techniques are commonly used for solving problems related to liquid flows by using analytical methods. Whereas, physical modelling is an important cognitive tool in the field of empirical identification of these phenomena. This allows for peer review and specification of the researched problems. By exploiting these relationships, a comparison of the obtained results was performed in the form of residence time distribution (RTD) curves and visualization of particular types of liquid steel flow distribution zones in the investigated tundish.
Źródło:
Archives of Metallurgy and Materials; 2016, 61, 4; 2057-2060
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of High Flow Rate Gas in the Process of Argon Blowing Trough Steel
Autorzy:
Merder, T.
Pieprzyca, J.
Warzecha, M.
Warzecha, P.
Powiązania:
https://bibliotekanauki.pl/articles/351630.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ladle
high intensity gas blowing
numerical modelling
physical modelling
Opis:
The article demonstrates results of modelling research tests concerning the analysis of possibilities of blowing gas into the metal bath at high flow rates in a steel ladle with a nominal capacity of 50 Mg. Various configurations concerning of gas introduction into the steel ladle were analysed. There were considered cases of blowing into the metal bath via one, two or three purging plugs, being installed on the bottom and via additional support for blowing the gas from the top through the lance. Results obtained from the water model of the reactor were verified with the results of numerical simulations.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2A; 905-910
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Physical Modelling of Tundish Slag Entrainment under Various Technological Conditions
Autorzy:
Michalek, K.
Gryc, K.
Socha, L.
Tkadlečková, M.
Saternus, M.
Pieprzyca, J.
Merder, T.
Pindor, L.
Powiązania:
https://bibliotekanauki.pl/articles/351348.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
steelmaking
tundish
slag entrainment
flow pattern
physical modelling
Opis:
This paper deals with the issue of physical modelling of vortexes creation and tundish slag entrainment over the mouth of the nozzle into the individual casting strands. Proper physical model is equivalent to the operational continuous casting machine No. 2 in TŘINECKÉ ŽELEZÁRNY, a.s. Physical modelling methodology and simulated operational conditions are shortly described. Physical modelling was used for the evaluation of current conditions of steel casting at the application of different impact pads in the tundish. Further, laboratory measurement on the physical model aiming the determination of exact critical periods of vortexes creation and study of the slag entrainment as a consequence of changes in surface level during the tundish refilling to standard level were realised. The obtained results were analysed and discussed.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 3; 1467-1471
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Theoretical and Experimental Analysis of Formability of Explosive Welded Mg/Al Bimetallic Bars
Autorzy:
Mróz, S.
Szota, P.
Bajor, T.
Stefanik, A.
Powiązania:
https://bibliotekanauki.pl/articles/353760.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Mg-Al bimetallic bars
plastic deformation
physical modelling
numerical modelling
FEM
Opis:
The paper has presented the results of theoretical studies and experimental tests of the plastic deformation of Mg/Al bimetallic specimens. Theoretical studies were carried out using the Forge2011® computer program. Physical modeling, on the other hand, was performed using the Gleeble3800 simulator. Bimetallic bars of an outer diameter of 22.5 mm and a cladding layer thickness of 1.7 mm were obtained by the explosive welding method. Samples for formability tests, characterized by a diameter-to-length ratio of 1, were taken from the bars. The theoretical studies and experimental tests were carried out for the temperature range from 300 to 400°C and for different strain rates. Based on the obtained investigation results it has been found that the main parameters influencing the formability of Mg/Al bimetallic bars are strain rate than the process temperature.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2A; 501-507
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies