Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "normal stress" wg kryterium: Temat


Wyświetlanie 1-14 z 14
Tytuł:
Effect of randomly distributed polypropylene fiber reinforcement on the shear behavior of sandy soil
Autorzy:
Benziane, Mehdi Missoum
Della, Noureddine
Denine, Sidali
Sert, Sedat
Nouri, Said
Powiązania:
https://bibliotekanauki.pl/articles/178213.pdf
Data publikacji:
2019
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
sand
direct shear box tests
polypropylene fibre
shear strength
normal stress
relative density
Opis:
The inclusions of geosynthetic materials (fibers, geomembranes and geotextiles) is a new improvement technique that ensures uniformity in the soil during construction. The use of tension resisting discreet inclusions like polypropylene fibers has attracted a significant amount of attention these past years in the improvement of soil performance in a cost-efficient manner. A series of direct shear box tests were conducted on unreinforced and reinforced Chlef sand with different contents of fibers (0, 0.25, 0.5 and0.75%) in order to study the mechanical behavior of sand reinforced with polypropylene fibers. Samples were prepared at three different relative densities 30%, 50% and 80% representing loose, medium dense and dense states, respectively, and performed at normal stresses of 50, 100 and 200 kPa. The experimental results show that the mechanical characteristics are improved with the addition of polypropylene fibers. The inclusion of randomly distributed fibers has a significant effect on the shear strength and dilation of sandy soil. The increase in strength is a function of fiber content, where it has been shown that the mechanical characteristics improve with the increase in fiber content up to 0.75%, this improvement is more significant at a higher normal stress and relative density.
Źródło:
Studia Geotechnica et Mechanica; 2019, 41, 3; 151-159
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A laboratory investigation on shear strength behavior of sandy soil: effect of glass fiber and clinker residue content
Autorzy:
Bouaricha, L.
Djafar Henni, A.
Lancelot, L.
Powiązania:
https://bibliotekanauki.pl/articles/178431.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
direct shear test
glass fibers
clinker residue
peak shear stress
sand
normal stress
cohesion
frictional angle
Opis:
A study was undertaken to investigate the shear strength parameters of treated sands reinforced with randomly distributed glass fibers by carrying out direct shear test after seven days curing periods. Firstly, we studied the fiber content and fiber length effect on the peak shear strength on samples. The second part gives a parametric analysis on the effect of glass fiber and clinker residue content on the shear strength parameters for two types of uniform Algerian sands having different particle sizes (Chlef sand and Rass sand) with an average relative density Dr = 50%. Finally, the test results show that the combination of glass fiber and clinker residue content can effectively improve the shear strength parameters of soil in comparison with unreinforced soil. For instance, there is a significant gain for the cohesion and friction angle of reinforced sand of Chlef. Compared to unreinforced sand, the cohesion for sand reinforced with different ratios of clinker residue increased by 4.36 to 43.08 kPa for Chlef sand and by 3.1 to 28.64 kPa for Rass sand. The feature friction angles increased from 38.73° to 43.01° (+4.28°), and after the treatment, clinker residue content of soil evaluated to 5% (WRC = 5%).
Źródło:
Studia Geotechnica et Mechanica; 2017, 39, 4; 3-15
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Metody pomiaru własności sprężystolepkich
Measuring methods of viscoelastic properties
Autorzy:
Kiljański, T.
Powiązania:
https://bibliotekanauki.pl/articles/2073007.pdf
Data publikacji:
2014
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
płyn sprężystolepki
naprężenia normalne
pełzanie
relaksacja
oscylacje
viscoelastic fluid
normal stress
creep
relaxation
oscillations
Opis:
Objawy sprężystolepkości płynu z reguły są szkodliwe w procesach technologicznych ze względu na generowanie dodatkowych naprężeń i związanych z nimi odkształceń, często obniżających jakość produktu. Te efekty mogą być zmniejszone przez odpowiedni dobór parametrów procesu technologicznego. Omówiono metody badania własności sprężystolepkich wykorzystujące przepływy ustalone (wiskozymetryczne), przepływy jednokierunkowe nieustalone i przepływy oscylacyjne. Przedstawiono test naprężeń normalnych, test pełzania, test relaksacyjny i badania oscylacyjne oraz wskazano, który z nich wybrać w celu uzyskania charakterystyki reologicznej płynu odpowiedniej dla danego procesu technologicznego.
Manifestation of fluid viscoelasticity is usually a disadvantage in technological processes due to the generation of additional stresses and relevant deformations often decreasing product quality. These effects can be restricted via appropriate selection of technological process parameters. Testing methods of viscoelastic properties using steady-state (viscometry), one-directional unsteady-state and oscillatory flows are discussed. The creep, relaxation and normal stresses tests are presented. It was indicated which of these tests should be chosen to obtain the fluid rheological characteristics appropriate for a given technological process.
Źródło:
Inżynieria i Aparatura Chemiczna; 2014, 5; 344--346
0368-0827
Pojawia się w:
Inżynieria i Aparatura Chemiczna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelling analysis of high effect of roll hoop main on the strength of student car formula chassis
Autorzy:
Tamjidillah, M.
Subagyo, R.
Isworo, H.
Nanlohy, H. Y.
Powiązania:
https://bibliotekanauki.pl/articles/368061.pdf
Data publikacji:
2020
Wydawca:
Stowarzyszenie Komputerowej Nauki o Materiałach i Inżynierii Powierzchni w Gliwicach
Tematy:
Student Formula car
Autodesk Inventor
roll-hoop play
normal stress
torsional stress
Formuła Student
pojazdy
naprężenie normalne
Opis:
Purpose: To analyse the strength of materials by means of optimization, find the best value of the strength test of mutually influential materials with a variation of roll-hoop height. Design/methodology/approach: The research began with the design of a threedimensional model by varying the height of the roll-hoop on chassis types: A, B, C, D, E, F, G, H ,and I. The height of the main roll hoop at each chassis is: 502, 504, 506 508, 510, 512, 514, 516 and 518 mm. Then by using the student version of Autodesk Inventor, a simulation is made to test: Deflection, Normal stress, Shear stress (T-x / T-y) and Torsional stress. The results of this test are used to analyse the types of chassis that have been designed so that the best chassis design is obtained. Findings: The results obtained in this study are the value of Normal stress decreases with increasing roll-hoop height, and applies inversely to the torsional stress value. Deflection values tend to be stable with increasing roll-hoop height, while Shear stress T-x and T-y values tend to fluctuate. Research limitations/implications: The chassis material uses carbon steel which has mechanical property values in accordance with 2015 FSAE Standard regulations. Practical implications: The optimization results of the design of the roll hoop height on the chassis show that the chassis type B with the main roll hoop height of 504 mm is the best with the lowest deflection value and the difference in tension according to the FSAE rules. Originality/value: The research that has been done only tests the strength of the ingredients separately. In this study trying to analyse the strength of the material by way of optimization to find the best value from the strength test of material that influence each other with a variation of roll-hoop height.
Źródło:
Journal of Achievements in Materials and Manufacturing Engineering; 2020, 100, 1; 26-40
1734-8412
Pojawia się w:
Journal of Achievements in Materials and Manufacturing Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of the potential usage of selected magnetic fluids in thrust slide bearings
Analiza możliwości zastosowania wybranych cieczy magnetycznych we wzdłużnych łożyskach ślizgowych
Autorzy:
Horak, W.
Salwiński, J.
Szczęch, M.
Powiązania:
https://bibliotekanauki.pl/articles/188095.pdf
Data publikacji:
2016
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
magnetorheological fluid
ferrofluid
rheological characteristics
normal stress
shear stress
ciecz magnetoreologiczna
ciecz ferromagnetyczna
charakterystyki reologiczne
naprężenie normalne
naprężenie styczne
Opis:
Magnetic fluids are substances whose rheological properties can be actively influenced by treatment with a magnetic field. Two main types of magnetic fluids can be distinguished: ferromagnetic fluids, and magnetorheological fluids. Ferrofluids are mostly used in sealing engineering, whereas magnetorheological fluids are usually applied in controlled systems for the dissipation of mechanical energy, like brakes and dampers. The ability to control the rheological properties of magnetic fluids opens new horizons for development in machine design, among others in the areas of bearing engineering. The paper presents a comparative analysis of the rheological characteristics of selected magnetic fluids with a focus on the possible areas of the application of these substances in bearing engineering.
Ciecze magnetyczne są to substancje, których właściwości reologiczne mogą być aktywnie kształtowane poprzez oddziaływanie na nie polem magnetycznym. Można wyróżnić dwa podstawowe typy cieczy magnetycznych: ciecze ferromagnetyczne oraz magnetoreologiczne. Znane są przemysłowe aplikacje cieczy ferromagnetycznych, przede wszystkim w konstrukcji uszczelnień, natomiast ciecze magnetoreologiczne znalazły zastosowanie głównie w układach dyssypacji energii mechanicznej o sterowanych parametrach pracy. Perspektywa wykorzystania możliwości sterowania właściwościami reologicznymi cieczy magnetycznych otwiera nowe horyzonty dla opracowywania konstrukcji urządzeń, między innymi w obszarze konstrukcji łożysk. W pracy przedstawiono analizę porównawczą charakterystyk reologicznych wybranych cieczy magnetoreologicznych i ferromagnetycznych ze zwróceniem uwagi na możliwe obszary zastosowania tych cieczy w inżynierii łożyskowania.
Źródło:
Tribologia; 2016, 269, 5; 41-49
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of geosynthetic interface friction at low normal stress: comparison between two different test procedures
Ocena oporów tarcia pomiędzy geosyntetykami podczas występowania małych naprężeń normalnych: porównanie dwóch metod badawczych
Autorzy:
Pavanello, P.
Carrubba, P.
Moraci, N.
Powiązania:
https://bibliotekanauki.pl/articles/28765739.pdf
Data publikacji:
2022
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
geosynthetic
interface friction
frictional resistance
shear resistance
shear test
direct shear test
horizontal shear test
normal stress
inclined plane
Źródło:
Acta Scientiarum Polonorum. Architectura; 2022, 21, 4; 3-10
1644-0633
Pojawia się w:
Acta Scientiarum Polonorum. Architectura
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical Modeling of the Degradation of the Normal Stress Under Large Number of Shearcycles
Autorzy:
Bellayoune, Assia
Messast, Salah
Boulon, Marc
Powiązania:
https://bibliotekanauki.pl/articles/2051692.pdf
Data publikacji:
2021
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
bearing capacity of piles
normal stress
shear
friction
degradation
numerical modeling
nośność pali
naprężenie normalne
tarcie
ścinanie
degradacja
modelowanie numeryczne
Opis:
The evaluation of friction is an important element in the verification of stability and the determination of the bearing capacity of piles. In the case of cyclic stress, the soil-pile interface has a relaxation which corresponds to a fall in the horizontal stress which represents the normal stress at the lateral surface of the pile. This paper presents an explicit formulation to express the degradation of the normal stress after a large number of shear cycles as a function of cyclic parameters. In this study we are interested in the exploitation of the cyclic shear tests carried out by Pra-ai with imposed normal rigidity (CNS) in order to demonstrate the phenomenon of falling of the normal stress. The approach presented in this paper consists in proposing a simple expression for estimating the degradation of normal stress as a function of cyclic shear parameters after a large number of cycles. The validation of this approach is verified by the application of this formulation to a real case where the comparison of the simulations made by this approach with those recorded on site shows the good adaptation of this approach to this type of problems.
Źródło:
Civil and Environmental Engineering Reports; 2021, 31, 3; 118-133
2080-5187
2450-8594
Pojawia się w:
Civil and Environmental Engineering Reports
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of load level of corner columns on punching shear resistance of flat slabs
Wpływ obciążenia słupa narożnego na nośność płyt płaskich z uwagi na przebicie
Autorzy:
Gołdyn, Michał
Urban, Tadeusz
Powiązania:
https://bibliotekanauki.pl/articles/390819.pdf
Data publikacji:
2020
Wydawca:
Politechnika Lubelska. Wydawnictwo Politechniki Lubelskiej
Tematy:
column-slab connection
punching shear
lateral expansion
membrane action
normal stress
połączenia płyta-słup
przebicie
odkształcenia poprzeczne
efekt membranowy
naprężenia normalne
Opis:
The problem related to the effect of the corner column load on the punching shear resistance of the slab was presented. Existing experimental studies on internal columns demonstrated that the column pressure could lead to an increase in the punching shear resistance. Because of different confinement conditions of corner column-slab connection joints, it is unclear if such an effect exists for corner columns. New experimental investigations were initiated to clarify this issue. They covered a total of three corner column-slab connection specimens – slabs with a thickness of 140 mm and a longitudinal reinforcement ratio ρl = 1.09% connected with columns of a cross-section of 200×200 mm. The only variable parameter was the column load equal to 500, 1000 and 1500 kN. A reduction of the slab load-carrying capacity of about 9% due to a three-fold increase in the column load was noted. Therefore, the effect of the column load turned out to be opposite to that observed for most previous tests on internal column-slab connections, which could have a result of a limited capacity of the slab reinforcement due to additional tensile forces from the lateral expansion of joint concrete. Comparison in the light of test results demonstrated, that EN 1992-1-1 procedure allowed for safe, yet conservative estimation of the punching shear resistance. An average ratio of experimental to theoretical load of 1.82 was obtained.
W artykule przedstawiono zagadnienie wpływu obciążenia słupa narożnego na nośność płyty na przebicie. Dotychczasowe, nieliczne badania eksperymentalne dotyczące słupów wewnętrznych wykazały, iż nacisk słupa może prowadzić do zwiększenia nośności na przebicie. Z uwagi na odmienne warunki skrępowania węzłów skrajnych połączeń płytowo-słupowych konieczne było jednak zweryfikowanie tego efektu w odniesieniu do slupów narożnych. W tym celu wykonano i zbadano trzy modele połączeń płytowo-słupowych, wykonanych w skali. Wszystkie modele charakteryzowały się jednakową geometrią i zbrojeniem. Płyty o grubości 140 mm i stopniu zbrojenia podłużnego ρl = 1,09% połączone były ze słupami o przekroju 200×200 mm. Jedyny parametr zmienny stanowiło obciążenie słupa, równe 500, 1000 oraz 1500 kN. Wskutek trzykrotnego zwiększenia obciążenia słupa odnotowano zmniejszenie nośności na przebicie o około 9%. Efekt obciążenia słupa na nośność płyty okazał się zatem przeciwny do obserwowanego w przypadku większości badań połączeń wewnętrznych, czego przyczyny należy upatrywać w ograniczeniu nośności zbrojenia podłużnego płyty ze względu na odkształcenia poprzeczne betonu węzła. Porównanie wyników badań z obliczeniami według EN 1992-1-1 wykazało, iż procedura normowa pozwoliła na bezpieczne, aczkolwiek konserwatywne oszacowanie nośności modeli. Uzyskano bowiem średni stosunek nośności eksperymentalnej do teoretycznej równy 1,82.
Źródło:
Budownictwo i Architektura; 2020, 19, 3; 44-56
1899-0665
Pojawia się w:
Budownictwo i Architektura
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Tests of polymeric adhesive joints in aspect of their application in prefabricated timber structures
Badania polimerowych złączy podatnych w aspekcie ich stosowania w prefabrykowanych konstrukcjach drewnianych
Autorzy:
Śliwa-Wieczorek, Klaudia
Zając, Bogusław
Kozik, Tomasz
Powiązania:
https://bibliotekanauki.pl/articles/230399.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
elastyczność
połączenie elastyczne
połączenie klejowe
odkształcenie
naprężenie ścinające
naprężenie normalne
dystrybucja
konstrukcja drewniana
flexibility
flexible joint
adhesive joint
deformation
shear stress
normal stress
distribution
timber structure
Opis:
The article concerns modern, flexible adhesive joints, which might be used in timber construction. The article discusses the test results carried out for timber elements joints using polymeric adhesives produced by Sika®. The scope of the tests includes the analysis of strength criteria, tests of polymer adhesion to the timber with a pull-off method, tests of polymer layer shearing between timber elements as well as examination of bending of timber elements joined with polymer. The conclusions indicate the types of these polymers which are recommended for the creation of polymeric joints of timber-polymeric type in timber constructions.
Dynamiczny rozwój połączeń klejowych, umożliwia ich zastosowanie już nie tylko w naprawach, czy wzmocnieniach głównie konstrukcji żelbetowych oraz murowych. Coraz częściej mówi się o zastąpieniu tradycyjnych łączników przez połączenia klejowe. Szczególnie interesujący jest rozwój połączeń na bazie polimerów w zastosowaniu w konstrukcjach drewnianych, który umożliwia eliminację lub znaczne ograniczenie występowania zjawiska koncentracji naprężeń, jak ma to miejsce w przypadku najbardziej powszechnych połączeń trzpieniowych. Szczególne znaczenie ma eliminacja tego zjawiska w obiektach drewnianych, poddanych oddziaływaniu silnych wiatrów, trzęsień ziemi, czy też dużych gradientów temperaturowych oraz wilgotności. Głównym celem artykułu jest omówienie wyników badań przeprowadzonych dla połączeń elementów drewnianych przy wykorzystaniu podatnych klejów polimerowych produkcji Sika®. Zakres badań obejmuje analizę kryteriów wytrzymałościowych, badania przyczepności polimeru do drewna metodą pull-off (na odrywanie), badania ścinania warstwy polimeru pomiędzy elementami drewnianymi oraz badania zginania elementów drewnianych zespolonych polimerem.
Źródło:
Archives of Civil Engineering; 2020, 66, 1; 113-125
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Tectonophysics map of discontinuous deformation of Rybnik region
Autorzy:
Głogowska, M.
Warzecha, R.
Powiązania:
https://bibliotekanauki.pl/articles/178635.pdf
Data publikacji:
2016
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
compaction areas
tectonophysic
minimum stress trajectories
normal faults
Opis:
In this paper, a Tectonophysics map of Rybnik region is presented which is based on the method of determining the direction of the trajectory of the principal stresses in the rock mass and axis orientation of these stresses. This method is used in tectonophysicsand is based on the character and parameters of faults. The whole map of Rybnik region encompasses an area of active mines: Rydułtowy-Anna, Marcel, Chwałowice, Jankowice as well as closed ones: Rymer and 1 May of Marcel mine. The paper presents only some fragments of the maps made for the four fault systems and a collective map of tectonophysic, i.e., showing chart areas of compaction for all the systems. The tectonophysics map was made to a scale of 1:20 000. Before the proper work which was the reconstruction of the compaction zone, preparatory work was done. This consisted of updates in 2013 of the tectonics of this area. As a result, tectonic maps were obtained where faults were projected on one level to get their proper azimuth and their inclination. So, a map was made which was used to separate four fault systems arising in similar conditions of stress. Next followed the reconstruction of the main stress fields, which was the cause of faults. On the map there are plotted trajectories showing minimum stress (σ3) and areas of compaction. The maps thus constructed will be used for further studies on the stress spreading and the impact of these areas for geomechanical properties.
Źródło:
Studia Geotechnica et Mechanica; 2016, 38, 2; 29-35
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The activity of antioxidant enzymes in colorectal adenocarcinoma and corresponding normal mucosa
Autorzy:
Strzelczyk, Joanna
Wielkoszyński, Tomasz
Krakowczyk, Łukasz
Adamek, Brygida
Zalewska-Ziob, Marzena
Gawron, Katarzyna
Kasperczyk, Janusz
Wiczkowski, Andrzej
Powiązania:
https://bibliotekanauki.pl/articles/1039648.pdf
Data publikacji:
2012
Wydawca:
Polskie Towarzystwo Biochemiczne
Tematy:
antioxidant enzymes
corresponding normal mucosa
colorectal adenocarcinoma
oxidative stress
Opis:
Oxidative stress is one of several factors which contribute to the development of colorectal carcinogenesis. The aim of the study was an assessment of the activity of antioxidant enzymes in tumour and corresponding normal distal mucosa in a group of patients with colorectal adenocarcinoma. Samples of tumour and corresponding normal mucosa were obtained during a resection of colorectal cancer from 47 patients aged between 26 and 82 years. The average distance of corresponding normal distal mucosa from the tumour was 4.49 cm. Activities of antioxidant enzymes: superoxide dismutase (SOD), glutathione reductase (GR), glutathione peroxidase (GPx), glutathione S-transferase (GST), and catalase (CAT) were measured in tissue homogenates. The patients were grouped according to the tumour stage (Duke's staging), grading, localization, and size of tumour, as well as age and sex. Statistical analysis was performed. The activity of SOD and GPx was considerably increased, while the activity of GST decreased significantly in tumour as compared with normal mucosa. GR activity in colorectal cancer was evidently higher in tumours of proximal location compared with the distal ones. The distance of corresponding normal distal mucosa from the tumour was analyzed and related to all assayed parameters. A decreased GST activity was observed in corresponding normal mucosa more than 5 cm distant from the tumour in patients with CD Duke's stage. The higher activity of superoxide dismutase and glutathione peroxidase in tumour compared to corresponding normal mucosa could indicate higher oxidative stress in colorectal adenocarcinoma cells.
Źródło:
Acta Biochimica Polonica; 2012, 59, 4; 549-556
0001-527X
Pojawia się w:
Acta Biochimica Polonica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Implementing SimulationX in the modelling of marine shafting steady state torsional vibrations
Autorzy:
Vulić, Nenad
Bratić, Karlo
Lalić, Branko
Stazić, Ladislav
Powiązania:
https://bibliotekanauki.pl/articles/1573607.pdf
Data publikacji:
2021
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
mechanical dynamic system
critical speeds
torsional stress amplitudes
two-stroke marine Diesel engine
normal firing
Opis:
Marine propulsion shafting systems are exposed to torsional vibrations originating from excitations in their prime movers and propellers. It is essential to analyse their steady state response in the earliest stage of ship design. The paper describes the implementation of SimulationX software based upon simulation modelling for these calculations. This software can be used either by the design office of the shipyard or by the classification society for verification within the plan approval phase. Some specifics of the input data preparation are briefly discussed. In addition, the simulation results depend on the modelling approach chosen. For these reasons, the real two-stroke Diesel engine ship propulsion system was chosen and several different models were implemented for system modelling. SimulationX calculation results are compared with those of two well-known and field-proven programs that use an analytical approach. Finally, the results are compared with the measurements performed on the actual newly built ship. Discussion reviews the selected SimulationX model, and its verification and validation in the case of engine cylinders with normal ignition.
Źródło:
Polish Maritime Research; 2021, 2; 63-71
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Strength of eccentrically tensioned reinforced concrete structures with small eccentricities by normal sections
Autorzy:
Dmytrenko, Yevhen
Yakovenko, Ihor
Fesenko, Oleg
Powiązania:
https://bibliotekanauki.pl/articles/35540855.pdf
Data publikacji:
2021
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
reinforced concrete structures
deformation model
two-line stress-strain diagram
non-eccentric tension
small eccentricities
normal cross sections
Opis:
It is implemented the method of normal rectangular sections slab (shell) reinforced concrete elements strength calculating with flat eccentric tensile strength using the deformation m ethod. The results of the calculation are analyzed for the case of eccentric tension with small eccentricities with varying next parameters: the height of the cross section and the reinforcement coefficient. It is investigated the character of diagrams condition change of section “N - εc(1)” at gradual change of the stress-strain state from eccentric to the central tension. It is revealed that when the eccentricity of external forces decreases, the compressed zone of concrete decreases until its complete disappearance, and at rather small values of eccentricities of force application the balance between external and internal forces cannot be found by the method of current norms. An equilibrium is found between internal and external forces only at a two-digit diagram of the distribution of relative longitudinal deformations (in the case of a compressed zone). Variants of the given problem decision without considerable loss of calculations accuracy are offered, the most expedient of which is transition to algorithm of calculation by a method of limiting efforts. It was accepted as the basic in the previous building norms. The results of numerical calculations performed in the software complex “Lira-CAD” and the corresponding mathematical modeling confirmed the rationality and allowable accuracy of further calculations by this method.
Źródło:
Scientific Review Engineering and Environmental Sciences; 2021, 30, 3; 424-438
1732-9353
Pojawia się w:
Scientific Review Engineering and Environmental Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
On the parameters of geometric constraints for cracked plates under tension – three-dimensional problems
Autorzy:
Graba, M.
Powiązania:
https://bibliotekanauki.pl/articles/264715.pdf
Data publikacji:
2017
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
CC(T)
DEN(T)
geometric constraints
stress triaxiality parameter
Q stresses
normal stresses
crack
naprężenia
pęknięcie
pękanie płyt
Opis:
This paper provides a comparative analysis of selected parameters of the geometric constraints for cracked plates subjected to tension. The results of three-dimensional numerical calculations were used to assess the distribution of these parameters around the crack front and their changes along the crack front. The study also involved considering the influence of the external load on the averaged values of the parameters of the geometric constraints as well as the relationship between the material constants and the level of the geometric constraints contributing to the actual fracture toughness for certain geometries.
Źródło:
International Journal of Applied Mechanics and Engineering; 2017, 22, 4; 901-919
1734-4492
2353-9003
Pojawia się w:
International Journal of Applied Mechanics and Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-14 z 14

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies