Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "interface layer" wg kryterium: Temat


Wyświetlanie 1-5 z 5
Tytuł:
Trend analysis of rail corrugation in metro lines considering friction memory and interface effects
Autorzy:
Wang, Zhiqiang
Lei, Zhenyu
Powiązania:
https://bibliotekanauki.pl/articles/2200893.pdf
Data publikacji:
2023
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
metro
rail corrugation
friction memory
interface layer
stick-slip characteristics
Opis:
In order to investigate the evolution trend of rail corrugation under the action of slip and interface effects, stick-slip vibration characteristics of a wheel-rail system in different line con- ditions have been analyzed in detail by establishing a complete three-dimensional coupling metro vehicle-track numerical model and considering the friction memory effect characteriz- ing the slip rate and state dependence as well as interface effect. The results show that on a straight line, the friction memory effect has less influence on the wheel-rail contact stick-slip characteristics, and the values and variation ranges of adhesion coefficients and creepages are relatively small, indicating that it is difficult for the wheel-rail system to have stick-slip vibration, which makes it less likely to form rail corrugation. On a curved line, the fluctua- tion amplitudes of the inside longitudinal stick-slip characteristics and the outside transverse stick-slip characteristics are relatively large, which illustrates that the inside wheel-rail sys- tem is more prone to stick-slip vibration in the longitudinal direction, while the outside wheel-rail system is more prone to stick-slip vibration in the transverse direction, thus lead- ing to different forms of rail corrugation. The friction memory effect reduces longitudinal and transverse creepages of both the inside and outside wheel-rail systems, demonstrating that the friction memory effect can moderate the relative wheel-rail slip and thus reduce the development rate of rail corrugation. The interface effect makes longitudinal and transverse adhesion coefficients of the wheel-rail system tend to homogenize and mostly decrease, while the corresponding creepages tend to increase. Although an increase in the creepage induces an enhanced interface slip, a smaller adhesion coefficient does not cause a significant change in the corrugation evolution. Friction memory and interface effects can cause the wheel-rail contact adhesion area ratio to increase, thus making the contact stick-slip distribution tend to homogenize, which is beneficial to reduce wear in the contact area and promote wear to homogenize.
Źródło:
Journal of Theoretical and Applied Mechanics; 2023, 61, 2; 331--342
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Finite element simulation of the normal interaction of particles in the visco-elastic solid
Symulacja oddziaływania cząstek ze sprężysto-lepkim ośrodkiem metodą elementów skończonych
Autorzy:
Rimsa, V.
Kacianauskas, R.
Sivilevicius, H.
Powiązania:
https://bibliotekanauki.pl/articles/368976.pdf
Data publikacji:
2011
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
cząstki
nielinowość geometryczna
lepkosprężystość
oddziaływanie w kierunku normalnym
warstwa graniczna
particles
geometric nonlinearity
viscoelastisity
normal interaction force
interface layer
Opis:
This paper addresses the 3D FE simulation of the normal interaction of stiff but deformable particles in binder matrix on the meso-scale. The particles are assumed to be elastic spheres while matrix is considered as viscoelastic solid. The investigation is aimed to capture interaction in terms of normal forces under tension. The problem is considered by applying geometrically linear and nonlinear approaches. Results illustrate influence of initial interparticle gap reduction of which yields significant increase of the interaction force. Comparison between purely elastic and viscoelastic solutions is also presented.
Niniejszy artykuł dotyczy trójwymiarowej symulacji metodą elementów skończonych oddziaływania w kierunku normalnym sztywnych, ale odkształcalnych cząstek w spoistej osnowie na poziomie mezoskopowym. Cząstki są traktowane jako sprężyste kule, zaś osnowa jako ciało lepkosprężyste. Badania mają na celu znalezienie sił oddziaływania pod obciążeniem. Zagadnienie jest rozpatrywane przy zastosowaniu modelu geometrycznie liniowego i nieliniowego. Wyniki pokazują wpływ wstępnego zmniejszenia odstępu na znaczący wzrost siły oddziaływania. Przedstawione jest również porównanie między rozwiązaniem sprężystym i lepkosprężystym.
Źródło:
Mechanics and Control; 2011, 30, 4; 245-253
2083-6759
2300-7079
Pojawia się w:
Mechanics and Control
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Charge-pumping characterization of SOI devices fabricated by means of wafer bonding over pre-patterned cavities
Autorzy:
Głuszko, G.
Łukasiak, L.
Kilchytska, V.
Chung, T. M.
Olbrechts, B.
Flandrie, D.
Raskin, J. P.
Powiązania:
https://bibliotekanauki.pl/articles/308669.pdf
Data publikacji:
2007
Wydawca:
Instytut Łączności - Państwowy Instytut Badawczy
Tematy:
charge-pumping
electrical characterization
interface traps
SOI
water bonding
Si layer transfer
Opis:
The quality of the silicon-buried oxide bonded interface of SOI devices created by thin Si film transfer and bonding over pre-patterned cavities, aiming at fabrication of DG and SON MOSFETs, is studied by means of chargepumping (CP) measurements. It is demonstrated that thanks to the chemical activation step, the quality of the bonded interface is remarkably good. Good agreement between values of front-interface threshold voltage determined from CP and I-V measurements is obtained.
Źródło:
Journal of Telecommunications and Information Technology; 2007, 3; 61-66
1509-4553
1899-8852
Pojawia się w:
Journal of Telecommunications and Information Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A method for determination of flow at the plane, horizontal interface separating streams of two different fluids
Autorzy:
Prosnak, W. J.
Cześnik, P. P.
Powiązania:
https://bibliotekanauki.pl/articles/241051.pdf
Data publikacji:
2005
Wydawca:
Polska Akademia Nauk. Instytut Budownictwa Wodnego PAN
Tematy:
interface
almost parallel streams of two fluids
boundary layer
ordinary differential equations
matching conditions
Opis:
The paper deals with the theoretical investigation of the phenomenon, which consists in generation - by wind - of the movement of water, the bodies of air and of water being separated by a horizontal, plane interface, which is identical with the free surface of water. A set of assumptions defining a physical model of the phenomenon, borrowed from Lock (1951), is introduced, as well as the mathematical description of this model. It reduces to a composite ordinary differential problem, containing two non-linear equations of the third order, which have to satisfy some boundary conditions. A novel method of solution of the differential problem just mentioned is presented in the paper. In the method use is made of exact formulae for coefficients of series representing the solution. The method seems to be competitive with the one given in the paper by Lock (1951).
Źródło:
Archives of Hydro-Engineering and Environmental Mechanics; 2005, 52, 2; 89-110
1231-3726
Pojawia się w:
Archives of Hydro-Engineering and Environmental Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of TRIZ methodology in diffusion welding system optimization
Zastosowanie metodologii TRIZ w optymalizacji systemu spawania dyfuzyjnego
Autorzy:
Ravinder-Reddy, N.
Satynarayana, V. V.
Prashanthi, M.
Suguna, N.
Powiązania:
https://bibliotekanauki.pl/articles/409636.pdf
Data publikacji:
2017
Wydawca:
STE GROUP
Tematy:
bonding pressure
bonding temperature
holding time
bonding strength
diffusion layer thicknes
interface hardness
ciśnienie klejenia
temperatura klejenia
czas wiązania
wytrzymałość wiązania
grubość warstwy dyfuzyjnej
twardość połączenia
Opis:
Welding is tremendously used in metal joining processes in the manufacturing process. In recent years, diffusion welding method has significantly increased the quality of a weld. Nevertheless, diffusion welding has some extent short research and application progress. Therefore, diffusion welding has a lack of relevant information, concerned with the joining of thick and thin materials with or without interlayers, on welding design such as fixture, parameters selection and integrated design. This article intends to combine innovative methods in the application of diffusion welding design. This will help to decrease trial and error or failure risks in the welding process being guided by the theory of inventive problem solving (TRIZ) design method. This article hopes to provide welding design personnel with innovative design ideas under research and for practical application.
Spawanie jest powszechnie stosowane w procesach produkcyjnych w procesie łączenia metali. W ostatnich latach metoda spawania dyfuzyjnego znacznie zwiększyła jakość spoiny. Niemniej jednak, metoda spawania dyfuzyjnego jest mało zgłębiona badawczo i krótko stosowana. Dlatego spawanie dyfuzyjne pozbawione jest istotnych informacji, związanych z łączeniem grubych i cienkich materiałów z warstwami pośrednimi lub bez ich udziału, w konstrukcji spawalniczej, takich jak mocowanie/oprawa, wybór parametrów i zintegrowana konstrukcja. Niniejszy artykuł ma na celu połączyć innowacyjne metody w zastosowaniu spawania dyfuzyjnego konstrukcji. Pomoże to zmniejszyć ryzyko prób i błędów lub niepowodzeń w procesie spawania, kierując się teorią metody rozwiązywania problemów (TRIZ). Artykuł ten ma na celu uzbrojenie personelu projektującego konstrukcje spawalnicze w innowacyjne pomysły projektowe w obszarze badań i praktycznych zastosowań.
Źródło:
Management Systems in Production Engineering; 2017, 4 (25); 237-240
2299-0461
Pojawia się w:
Management Systems in Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-5 z 5

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies