Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "friction factor simulation" wg kryterium: Temat


Wyświetlanie 1-3 z 3
Tytuł:
Simulation of the friction factor in a yield-stress slurry flow which exhibits turbulence damping near the pipe wall
Symulacja strat tarcia w przepływie szlamu z progiem płynięcia, w którym występuje tłumienie turbulencji
Autorzy:
Bartosik, A.
Powiązania:
https://bibliotekanauki.pl/articles/280881.pdf
Data publikacji:
2011
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
Bingham flow
turbulence modelling
damping of turbulence
friction factor simulation
Opis:
The paper deals with the mathematical modelling of fully developed turbulent flow of a Bingham hydromixture in a pipe. The mathematical model is based on time averaged Navier-Stokes equations and uses the apparent viscosity concept. The problem of closure of the turbulence stress tensor was solved by the two-equation turbulence model in which a modified turbulence damping function was taken into account. The final form of the mathematical model constitutes a set of three non-linear partial differential equations. The main aim of the paper is to demonstrate a significant decrease of turbulence near the pipe wall, as the friction factor is below that for a water flow. The paper presents results of numerical simulation of the frictional head loss and friction factor for slurry flows with low, moderate, and high yield stresses. Predicted frictional head losses have been compared with experimental data showing satisfying agreement. It is demonstrated that the frictional head loss and the friction factor substantially depend on the yield stress. The results of numerical simulation are presented as figures and conclusions. Possible causes of turbulence damping near the pipe wall are discussed.
Artykuł dotyczy matematycznego modelowania w pełni rozwiniętego przepływu hydromieszaniny Binghama w przewodzie kołowym. Model matematyczny zbudowano na bazie równań Naviera-Stokesa z zastosowaniem koncepcji lepkości pozornej. Problem domknięcia układu równań, wynikający z dodatkowych składowych tensora naprężeń turbulentnych, rozwiązano poprzez użycie dwu równaniowego modelu turbulencji, w którym zastosowano zmodyfikowaną funkcję tłumiącą turbulencję przy ścianie. Ostateczna postać modelu matematycznego zawiera trzy nieliniowe równania różniczkowe cząstkowe. Głównym celem pracy jest przedstawienie wzmożonego tłumienia turbulencji w obszarze przyściennym, jako że współczynnik strat tarcia hydromieszaniny jest niższy w stosunku do wody. Artykuł przedstawia wyniki numerycznej symulacji współczynnika strat tarcia dla szlamu z niskim, umiarkowanym i wysokim progiem płynięcia. Obliczony jednostkowy spadek ciśnienia porównano z wynikami badań eksperymentalnych, uzyskując satysfakcjonującą dokładność. Wykazano, że jednostkowy spadek ciśnienia i współczynnik strat tarcia zależą istotnie od progu płynięcia. Wyniki numerycznej symulacji przedstawiono w postaci wykresów i wniosków oraz omówiono możliwe przyczyny wzmożonego zjawiska tłumienia turbulencji przy ścianie.
Źródło:
Journal of Theoretical and Applied Mechanics; 2011, 49, 2; 283-300
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical Study of Friction Factor and Heat Transfer Characteristics for Single-Phase Turbulent Flow in Tubes with Helical Micro-Fins
Numeryczne badanie charakterystyk cieplnych i współczynników tarcia turbulentnych przepływów jednofazowych w rurach z mikro-ożebrowaniem helikalnym
Autorzy:
Jasiński, P.
Powiązania:
https://bibliotekanauki.pl/articles/140332.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
numerical simulation
heat transfer
friction factor
helical micro-fins
micro-ribs
symulacja numeryczna
przepływ ciepła
współczynnik tarcia
mikro-ożebrowanie helikalne
mikro-żebra
Opis:
The paper presents a numerical study on the heat transfer and pressure drop, related to flow in pipes with helical micro-fins. For all tested geometries, one applied a constant wall heat flux and fully developed 3D turbulent flow conditions. The influence of the angle of micro fins (referred to the tube axis) on thermal-flow characteristics were tested. The value of this angle was varied – with a step of 10 degrees – from 0 to 90 degrees (representing grooves parallel and perpendicular to the axis, respectively). Before numerical investigation, the pipe with helical angle of 30 degree was tested on an experimental stand. The results obtained from experiment and numerical simulations were compared and presented on the charts. As an effect of the numerical simulations, the friction factor f and Nusselt number characteristics was determined for the range of Re=104/1.6x106. The analysis of the results showed high, irregular influence of the helical angle on thermal characteristics and pressure drops. Additionally, the ratios: f/fplain, Nu/Nuplain and efficiency indexes (Nu/Nuplain)/( f/fplain) as a function of the Reynolds number for every helical angle were shown on the charts.
W tym artykule przedstawiono badania wymiany ciepła i spadku ciśnienia rur z mikroożebrowaniem śrubowym z wykorzystaniem symulacji numerycznych. Dla wszystkich badanych geometrii założono stały strumień ciepła na ściance oraz w pełni rozwinięty, turbulentny przepływ 3D. Badano wpływ kąta mikro-ożebrowania ścianki (odniesionego do osi rury) na charakterystyki cieplno-przepływowe takiego kanału. Wartość wspomnianego kąta zmieniano – co 10 stopni – w zakresie od 0 do 90 stopni (odpowiada on rowkom: równoległym i prostopadłym do osi rury). Przed wykonaniem symulacji numerycznych, zbadano doświadczalnie rurę z 30-stopniowym kątem mikro-ożebrowania i porównano tak otrzymane rezultaty. Z symulacji numerycznych uzyskano charakterystyki współczynnika tarcia i liczby Nusselta w zakresie liczb Reynoldsa 104 /1.6 x106. Ponadto, na wykresach zostały pokazane współczynniki ( f/fplain) oraz (Nu/Nuplain) a także wskaźnik efektywności (Nu/Nuplain)/( f/fplain) w funkcji liczby Reynoldsa dla każdego kąta mikro-ożebrowania. Analiza wyników wykazuje duży i nierównomierny wpływ kąta mikro-ożebrowania zarówno na spadki ciśnienia jak i na charakterystyki cieplne.
Źródło:
Archive of Mechanical Engineering; 2012, LIX, 4; 469-485
0004-0738
Pojawia się w:
Archive of Mechanical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research of Tribological and Thermodynamic Parameters of the WC-Cu Braking System of the Experimental Modular Electric Vehicle
Autorzy:
Varecha, Daniel
Galik, Jan
Kohar, Robert
Gajdosik, Tomas
Gajdac, Igor
Jenis, Jozef
Powiązania:
https://bibliotekanauki.pl/articles/26081012.pdf
Data publikacji:
2023
Wydawca:
Stowarzyszenie Menedżerów Jakości i Produkcji
Tematy:
powłoka WC-Cu
współczynnik tarcia
pojazd elektryczny
układ hamulcowy
symulacja hamowania
WC-Cu coating
friction factor
electric vehicle
braking system
simulation of braking
Opis:
The authors of this manuscript present the development of a braking system with friction material baseWC-Cu coating for the electric vehicle. This manuscript follows on from the original development of an AGV multi-disc braking system and an experimental investigation of the friction factor of WC-Cu coatings. In addition to developing the mechanical elements and construction of the electric vehicle, the tribological parameters of three samples of the steel substrate, the C45 with WC-Cu coating, were investigated in the tribological laboratory. A metallic coating of the WC-Cu base was applied on theC45 steel substrate using electro-spark deposition coating technology. The experiment used three samples with different percentage ratios of chemical elements in the coating structure. The tribometer working on a “Ball on Plate” principle was an investigation of the friction factor of all samples duringthe experiment. Subsequently, the surface of the samples was modified structure WC-Cu with laser technology. The microhardness of modified and unmodified coatings according to the Vickers methodology was investigated in the next stage. At the end of the experimental investigation, a braking simulation was created in the programming environment of the Matlab® software, considering all driving resistances. The researchers also focused on the simulation of heat conduction during braking for some considered driving modes with braking on a level and with a 20% slope roadway. The simulation of heat flow was carried out in the Matlab® programming environment using the Fourier partial differential equation for non-stationary heat conduction.
Źródło:
Production Engineering Archives; 2023, 29, 2; 116--127
2353-5156
2353-7779
Pojawia się w:
Production Engineering Archives
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies