Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "experimental study" wg kryterium: Temat


Tytuł:
An experimental investigation conducted in order to determine bearing dynamic coefficients of two hydrodynamic bearings using impulse responses
Autorzy:
Breńkacz, Ł.
Żywica, G.
Powiązania:
https://bibliotekanauki.pl/articles/175435.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hydrodynamic bearings
bearing dynamic coefficients
experimental study
Opis:
The paper presents the experimental investigation carried out in order to identify bearing dynamic coefficients of two hydrodynamic bearings from impulse responses. In this method the stiffness, damping and mass coefficients of two hydrodynamic bearings were calculated in a single algorithm. For each rotational speed, were obtained 12 dynamic coefficients which enable to fully describe the dynamic state of the rotor. Exciting force signals, applied using an impact hammer were shown. Displacements of the shaft were measured by eddy current sensors. The measurements were carried out at various rotational speeds, including resonance speeds. The vibration amplitude in a resonance case increases significantly with time after the excitation was induced by an impact hammer. Excitations of the rotor with an impact hammer were recorded using a high-speed camera. These unique recordings and simultaneous analysis of the trajectory of the bearing journals depict the contact phenomena that occur during impulse excitation of the rotor.
Źródło:
Transactions of the Institute of Fluid-Flow Machinery; 2016, 133; 39-54
0079-3205
Pojawia się w:
Transactions of the Institute of Fluid-Flow Machinery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study of topology and vortex structure in turbine cascades with tip clearance under different incidence angles
Badania topologii i struktury wirów palisady turbiny z luzem wierzchołkowym przy różnych kątach natarcia
Autorzy:
Yan, P. G.
Qiang, X. Q.
Teng, J. F.
Han, W. J.
Powiązania:
https://bibliotekanauki.pl/articles/279519.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
turbine cascade
tip clearance
topological rules
experimental study
Opis:
Three sets of conventional straight, positive curved and negative curved turbine cascades with tip clearance were tested with experimental measurement. The impact of incidence angles and blade bending on the tip leakage was studied under larger clearance (0.036 of span). An ink trace visualization of the wall flow and topology theory was adopted and thus the topological structures of the blade surface, the upper and lower end wall were analyzed in this paper. It was found that, compared with the same cascade under the zero incidence angle, the saddle points all move to the upstream, the scope of the separation expands along the flow and span direction, and the separation line of the upper and lower passage vortex climb to the middle span of the blade when the flow incidence angle increased from zero to 20º. Under the condition of zero and 20º incidence angle, the positive curved blade will eliminate the upper passage vortex. The numbers of singular points are reduced and the interaction loss between the passage vortex and the leakage vortex is greatly reduced too. On the other hand, it also strengthens the blocking effect of the end wall cross flow on the leakage flow, thereby reduces the relative leakage flow rate.
W pracy zaprezentowano wyniki pomiarów eksperymentalnych trzech zestawów konwencjonalnych palisad turbin o prostym, dodatnio i ujemnie zakrzywionym profilu. Zbadano wpływ kąta natarcia oraz efekt zginania łopatek na straty wskutek upływu przy luzie wierzchołkowym sięgającym 3.6% rozpiętości łopatek. Do analizy zastosowano wizualizację śladów pozostawianych barwnikiem oraz teorię topologii, tj. struktur topologicznych reprezentujących powierzchnię łopatki oraz górnej i dolnej ściany krańcowej. Zaobserwowano, że w porównaniu do analogicznej palisady o zerowym kącie natarcia wszystkie punkty siodłowe przesuwają się w gorę przepływu, a obszar oderwania strugi rozszerza się wzdłuż promienia łopatki. Jednocześnie granica oderwania górnego i dolnego wiru przemieszcza się ku środkowi łopatki, gdy kąt natarcia narasta od zera do 20◦. Przy tych granicznych wartościach kąta natarcia łopatki o dodatniej krzywiźnie profilu eliminują górny wir podczas przejścia. Ponadto okazało się, że liczba punktów osobliwych zmniejszyła się podobnie, jak osłabiła się interakcja pomiędzy wirami przejścia i wirami upływu. Stwierdzono, że wzmacnia to efekt blokowania upływu poprzecznym przepływem na krańcowej ścianie łopatki, co ostatecznie redukuje straty indukowane upływem.
Źródło:
Journal of Theoretical and Applied Mechanics; 2013, 51, 2; 363-373
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ehksperimental'nye issledovanija razbrasyvatelja podstilki s rotorno-pal'cevym rabochim organom
Experimental studies of the straw thrower with a rotary working body
Autorzy:
Pariev, A.
Boltianskijj, B.
Drobyshev, O.
Korotchenko, T.
Powiązania:
https://bibliotekanauki.pl/articles/76738.pdf
Data publikacji:
2016
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
straw
spreader
rotary-finger body
experimental study
testing
Źródło:
Motrol. Motoryzacja i Energetyka Rolnictwa; 2016, 18, 1
1730-8658
Pojawia się w:
Motrol. Motoryzacja i Energetyka Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
FEM and experimental based analysis of the stamping process of aluminum alloy
Autorzy:
Różyło, P.
Wójcik, Ł.
Powiązania:
https://bibliotekanauki.pl/articles/102747.pdf
Data publikacji:
2017
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
pressing
experimental study
numerical analysis
finite element method
Opis:
The subject of the study was aluminum samples of varying thickness. The aim of the study was to perform the experimental stamping process of the samples on a universal testing machine and a numerical analysis on two independent computer systems Abaqus® and Deform-3D. As part of the numerical analysis, bilinear material model was included, taking into account elastic and plastic characteristics. The study was conducted in a dynamic environment with geometric nonlinearity. The results obtained from experimental research were confronted with those obtained by FEM computer simulation. During the research, numerical model of the stamping process has been developed, which was validated with the results of experimental research.
Źródło:
Advances in Science and Technology. Research Journal; 2017, 11, 3; 94-101
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Issledovanija sovmestnojj raboty osvetljajushhejj centrifugi i ustanovki membrannojj ul'trafil'tracii
Researching the cooperation work of clarifying centrifuge and ultrafiltration membrane plant
Autorzy:
Ehpojan, S.
Karagjaur, A.
Babenko, C.
Golubka, A.
Powiązania:
https://bibliotekanauki.pl/articles/76321.pdf
Data publikacji:
2015
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
cooperation
experimental study
total suspended solid
water
filtration
theoretical study
Źródło:
Motrol. Motoryzacja i Energetyka Rolnictwa; 2015, 17, 6
1730-8658
Pojawia się w:
Motrol. Motoryzacja i Energetyka Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Search for knowledge and professional scepticism of accounting students – an experimental study
Autorzy:
Ciołek, Maciej
Powiązania:
https://bibliotekanauki.pl/articles/582953.pdf
Data publikacji:
2018
Wydawca:
Wydawnictwo Uniwersytetu Ekonomicznego we Wrocławiu
Tematy:
auditing
search for knowledge
accounting students
experimental study
HPSS
Opis:
The purpose of this study is to examine whether university accounting programs shape such ‘search for knowledge’ trait in significantly more effective comparing other university programs in the field of economy. For this purpose I conducted an experimental study using Hurtt Professional Skepticism Scale – HPSS which is one of the most recognized skepticism measures. I surveyed 432 students of Poznań University of Economics who follow either accounting program or management program (control group). The results showed that only programs in accounting increased the mean level of ‘search for knowledge’ trait significantly comparing to management program. The robustness analysis showed that gender, professional experience and length of service had no statistically significant impact on results.
Źródło:
Prace Naukowe Uniwersytetu Ekonomicznego we Wrocławiu; 2018, 515; 243-256
1899-3192
Pojawia się w:
Prace Naukowe Uniwersytetu Ekonomicznego we Wrocławiu
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A study of oxidative stress and pulmonary damage after silica instillation in rats and the effect of curcumin administration
Autorzy:
Barsan, Maria
Rajnoveanu, Armand G.
Cocarla, Aristotel
Bolfa, Pompei
Login, Cezar C.
Socaciu, Andreea I.
Decea, Nicoleta
Leucuta, Daniel-Corneliu
Powiązania:
https://bibliotekanauki.pl/articles/2081923.pdf
Data publikacji:
2021-06-30
Wydawca:
Instytut Medycyny Pracy im. prof. dra Jerzego Nofera w Łodzi
Tematy:
curcumin
silicosis
experimental study
silica
oxidative stress
lung tissue
Opis:
BackgroundThe authors’ aim was to study the dynamics of oxidative stress in experimental exposure to silica dust, to evaluate the histopathological findings in the phase preceding the formation of fibrous/fibrohyaline pulmonary nodules, and to assess the effects of curcumin administration.Material and MethodsThe research was performed on 48 male Wistar rats with an average weight of 320 g. Overall, 38 rats were instilled with a single dose of 0.3 ml suspension containing 30 mg of a SiO2/ml saline solution, and were sacrificed 30, 90 and 120 days after instillation; 14 of those sacrificed on days 90 and 120 also received curcumin. The control group included 10 animals which were instilled with a saline solution. Malondialdehyde (MDA), carbonyl proteins (CPs), total thiolic proteins (TPs) and reduced glutathione (GSH) were determined in blood and the lung tissue. The standard technique for pulmonary toxicology developed by Porter was applied to semi-quantitatively assess the histopathological findings.ResultsIt was found that MDA had increased significantly early on in both biological environments and remained elevated, and adding curcumin proved beneficial, while CPs only increased moderately in the lung tissue without a curcumin impact. Moreover, TPs dropped abruptly, significantly and persistently in the lung tissue and blood, and were not influenced by curcumin. Finally, GSH decreased significantly and intensely in the lung tissue and blood, with curcumin lowering the levels towards those found within the control group. The histopathological examination identified nodules of a cellular type, without any fibrosis, but with spots of associated lipoproteinosis. The early lesions in the airways and vessels were suggestive of a remodeling process. Curcumin diminished the occurrence of alveolitis but not the remodeling process.ConclusionsThe study confirms the early onset of oxidative stress in experimental silicosis. It also simultaneously and dynamically researches markers of oxidative stress in blood and the lung tissue. Curcumin proved beneficial on oxidative stress and lesions in the alveolar epithelia, but ineffective in preventing vascular and airway remodeling. Med Pr. 2021;72(3):239–47
Źródło:
Medycyna Pracy; 2021, 72, 3; 239-247
0465-5893
2353-1339
Pojawia się w:
Medycyna Pracy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of optimal planning methodologies for investigation of technological processes, devices and systems
Primenenie metodologii optimalnogo planirovanija dlja issledovanija tekhnologicheskikh processov, priborov i sistem
Autorzy:
Kirichenko, I.
Koshevoy, N.
Kostenko, E.
Rozhnova, V.
Powiązania:
https://bibliotekanauki.pl/articles/793489.pdf
Data publikacji:
2013
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
methodology
cost
mathematical model
experimental planning
hardware
software
experimental study
technological process
Źródło:
Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2013, 13, 3
1641-7739
Pojawia się w:
Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Vlijanie parametrov lezvija na dolgovechnost lap kultivatorov
Experimental study of homogeneous wear curved blade
Autorzy:
Kozachenko, A.
Shkregal, A.
Bleznjuk, O.
Votchenko, A.
Drobotenko, A.
Powiązania:
https://bibliotekanauki.pl/articles/76715.pdf
Data publikacji:
2013
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
cultivator
shape blade
wear
durability
cultivator paw
strengthening
experimental study
Źródło:
Motrol. Motoryzacja i Energetyka Rolnictwa; 2013, 15, 7
1730-8658
Pojawia się w:
Motrol. Motoryzacja i Energetyka Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Results of experimental studies on choice of automobile intercity transport delivery schemes for packaged cargo
Rezul'taty ehksperimental'nykh issledovanijj po vyboru transportno-tekhnologicheskikh skhem dostavki tarno-shtuchnykh gruzov avtomobil'nym transportom v mezhdugorodnom soobshhenii
Autorzy:
Naumov, V.
Shulika, O.
Velikodnyi, D.
Powiązania:
https://bibliotekanauki.pl/articles/76552.pdf
Data publikacji:
2015
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
road transport
technological parameter
transport technology
experimental study
automobile transport
Źródło:
Motrol. Motoryzacja i Energetyka Rolnictwa; 2015, 17, 7
1730-8658
Pojawia się w:
Motrol. Motoryzacja i Energetyka Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental study of hydraulic response of smooth submerged breakwaters to irregular waves
Autorzy:
Mahmoudof, S.M.
Hajivalie, F.
Powiązania:
https://bibliotekanauki.pl/articles/2078821.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Instytut Oceanologii PAN
Tematy:
submerged breakwater
irregular wave
experimental study
transmission
reflection
coastal area
Opis:
This paper presents the results of a laboratory experiment on transmission, reflection, and dissipation of irregular waves over smooth impermeable submerged breakwaters. Experiments included 75 JONSWAP-based irregular waves with five different wave characteristics generated at three water depths in a 2D wave flume. The investigated breakwater sections were three rectangular breakwaters with different widths, a toothed rectangular breakwater, and a trapezoidal breakwater with a slope of 1:2. A new comprehensive dimensionless parameter (β) was proposed representing both wave hydrodynamic and breakwater geometry characteristics. This parameter could be employed as a suitable descriptive option to make an accurate estimate of the hydraulic performances of submerged breakwaters. The β parameter is composed of four conventional simple dimensionless variables. However, the results revealed that the relative submergence depth significantly affects the hydraulic responses of submerged breakwaters. The transmission, reflection and dissipation of waves show a logarithmic growth, a logarithmic reduction, and a quadratic decreasing trend against the increasing of β parameter, respectively. The verifications of results revealed the high efficiency of β parameter for data reported by Carevic et al. (2013) with R2 = 0.88 and high agreement with predictions made by Van der Meer et al. (2005) formulation with R2 = 0.93.
Źródło:
Oceanologia; 2021, 63, 4; 448-462
0078-3234
Pojawia się w:
Oceanologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impact of low-temperature corona discharges on gaseous pollutants level in diesel engines exhaust gas
Autorzy:
Irzycki, A.
Kalina, P.
Snopkiewicz, K.
Powiązania:
https://bibliotekanauki.pl/articles/246916.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
exhaust gas
plasma reactor
emissions of gaseous toxins
experimental study
Opis:
This publication presents the results of research on level changes of gaseous pollutants contained in the exhaust gas in the consequence of applying of equipment taking advantage of low-temperature corona discharges. Not only influence of different plasma reactor configurations on the emission of toxins have been evaluated, but also on the main parameters of the engine under test and exhaust gas cleaning efficiency as well. The device supplied by DC voltage of 10-15 kV the operating value generated a low-temperature corona discharge in the especially formed electrostatic field. The devices were located behind the exhaust manifold of Diesel engine then operated in the high temperature zone of exhaust. The survey was realized in parallel with on-going research program at Institute of Aviation which has related to purification of Diesel engine's exhaust gas from particulates. The test results of emission of toxins obtained using the flat-arrangement and the axial-symmetric reactor systems were compared and discussed. The multi-variant designs of axial-symmetric device allowed the purposeful formation of favourable shape and intensity of electrostatic field and values of current, which induced the corona discharge. This activity has created better research capabilities for different geometric configurations of the reactors, namely linear and angular location and size of deflecting electrodes, structure of blade assembly generating a corona discharge, matching of proper distance between deflecting electrodes and blades.
Źródło:
Journal of KONES; 2010, 17, 2; 145-152
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Studies of flexibility of a steel adjustable foundation chock
Analiza odkształcalności stalowej nastawnej podkładki fundamentowej
Autorzy:
Grudziński, P.
Konowalski, K.
Powiązania:
https://bibliotekanauki.pl/articles/175788.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
podkładka fundamentowa
odkształcenie
badania doświadczalne
foundation chock
deformation
experimental study
Opis:
The paper presents a description and results of a flexibility study of a steel adjustable foundation chock (VibraconŽ SM). Chocks of this type are used in so-called rigid seatings (mountings) on foundations of heavy machinery and equipment, which require precise alignment and adjustment. They are an alternative to conventional (ordinary) metal chocks or new generation chocks - which are ready-cast with specifically for this purpose developed polymer composites. Experimental studies were conducted in laboratory conditions on an original new chock. The characteristics of deformation for this chock were determined in conditions close to the operation conditions of such chocks. The results show that in the investigated system there are significant deformations of a non-linear-elastic character. They allow one to better understand and explain many complex phenomena occurring in real structural connections with such type of chocks. They also constitute an experimental basis for appropriate modeling and analysis of strength and vibrations occurring in such systems.
W pracy przedstawiono analizę wyników badań podatności na odkształcenia sprężyste stalowej nastawnej podkładki fundamentowej (VibraconŽSM). Podkładki stosowane są w posadowieniach, na fundamentach maszyn i urządzeń o dużej masie, wymagających dokładnego ustawienia i regulacji - osiowania. Stanowią alternatywę dla tradycyjnie stosowanych podkładek metalowych albo podkładek nowej generacji - wytwarzanych z kompozytów polimerowych. Badania doświadczalne prowadzono w warunkach laboratoryjnych z użyciem nowej podkładki. Wyznaczono charakterystyki odkształceń w warunkach zbliżonych do eksploatacji. Stwierdzono występowanie w badanym układzie dużego odkształcenia o charakterze nieliniowo-sprężystym. Przeprowadzona analiza wyników badań umożliwiła charakteryzację złożonych zjawisk występujących w rzeczywistych połączeniach konstrukcyjnych z użyciem tych podkładek. Stanowią również doświadczalną podstawę do procesu modelowania oraz analizy wytrzymałości i drgań, występujących w układach mechanicznych.
Źródło:
Advances in Manufacturing Science and Technology; 2012, 36, 2; 79-90
0137-4478
Pojawia się w:
Advances in Manufacturing Science and Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Obosnovanie konstruktivno-funkciohal'nojj skhemy i rezul'taty ehksperimental'nykh issledovanijj barabonnogo dozatora kombikormov
Substantiation of constructive - functional schemes and results of experimental researches barabany feed dispenser
Autorzy:
Radchuk, V.
Powiązania:
https://bibliotekanauki.pl/articles/77369.pdf
Data publikacji:
2014
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
experimental research
dispenser
feed
vertical axis
honeycomb
drum
performance
experimental study
regression equation
Źródło:
Motrol. Motoryzacja i Energetyka Rolnictwa; 2014, 16, 3
1730-8658
Pojawia się w:
Motrol. Motoryzacja i Energetyka Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Medodika i ehsperimentalnye issledovanija morfologicheskikh i prochnostnykh kharakteristik obertok kukuruzy
Methods and experimental studies of morphological and strength characteristics wrappers corn
Autorzy:
Bondarenko, A.
Gruban, V.
Powiązania:
https://bibliotekanauki.pl/articles/77832.pdf
Data publikacji:
2015
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
experimental study
anatomical study
strength property
maize
leaf
corn cob
harvesting
cleaning process
Źródło:
Motrol. Motoryzacja i Energetyka Rolnictwa; 2015, 17, 2
1730-8658
Pojawia się w:
Motrol. Motoryzacja i Energetyka Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies