Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "dynamic coefficients" wg kryterium: Temat


Wyświetlanie 1-5 z 5
Tytuł:
An experimental investigation conducted in order to determine bearing dynamic coefficients of two hydrodynamic bearings using impulse responses
Autorzy:
Breńkacz, Ł.
Żywica, G.
Powiązania:
https://bibliotekanauki.pl/articles/175435.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hydrodynamic bearings
bearing dynamic coefficients
experimental study
Opis:
The paper presents the experimental investigation carried out in order to identify bearing dynamic coefficients of two hydrodynamic bearings from impulse responses. In this method the stiffness, damping and mass coefficients of two hydrodynamic bearings were calculated in a single algorithm. For each rotational speed, were obtained 12 dynamic coefficients which enable to fully describe the dynamic state of the rotor. Exciting force signals, applied using an impact hammer were shown. Displacements of the shaft were measured by eddy current sensors. The measurements were carried out at various rotational speeds, including resonance speeds. The vibration amplitude in a resonance case increases significantly with time after the excitation was induced by an impact hammer. Excitations of the rotor with an impact hammer were recorded using a high-speed camera. These unique recordings and simultaneous analysis of the trajectory of the bearing journals depict the contact phenomena that occur during impulse excitation of the rotor.
Źródło:
Transactions of the Institute of Fluid-Flow Machinery; 2016, 133; 39-54
0079-3205
Pojawia się w:
Transactions of the Institute of Fluid-Flow Machinery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Cutting parameters and vibrations analysis of magnetic bearing spindle in milling process
Autorzy:
Bouaziz, A.
Barkallah, M.
Bouaziz, S.
Choley, J. Y.
Haddar, M.
Powiązania:
https://bibliotekanauki.pl/articles/279623.pdf
Data publikacji:
2016
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
milling process
cutting forces
chip thickness
dynamic coefficients
orbit
Opis:
In modern production, milling is considered the widespread cutting process in the formatting field. It remains important to study this manufacturing process as it can be subject to some parasitic phenomena that can degrade surface roughness of the machined part, increase tool wear and reduce spindle life span. In fact, the best quality work piece is obtained with a suitable choice of parameters and cutting conditions. In another hand, the study of tool vibrations and the cutting force attitude is related to the study of bearings as they present an essential part in the spindle system. In this work, a modeling of a High Speed Milling (HSM) spindle supported by two pair of Active Magnetic Bearings (AMB) is presented. The spindle is modeled by Timoshenko beam finite elements where six degrees of freedom are taken into account. The rigid displacements are also introduced in the modeling. Gyroscopic and centrifugal terms are included in the general equation. The bearings reaction forces are modeled as linear functions of journal displacement and velocity in the bearing clearance. A cutting force model for peripheral milling is proposed to estimate the tool-tip dynamic responses as well as dynamic cutting forces which are also numerically investigated. The time history of response, orbit, FFT diagram at the tool-tip center and the bearings dynamic coefficients are plotted to analyze dynamic behavior of the spindle.
Źródło:
Journal of Theoretical and Applied Mechanics; 2016, 54, 3; 691-703
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions
Autorzy:
Breńkacz, Ł.
Żywica, G.
Drosińska-Komor, M.
Powiązania:
https://bibliotekanauki.pl/articles/259675.pdf
Data publikacji:
2017
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
bearing dynamic coefficients
experimental research
nonlinear coefficients
impact excitation
hydrodynamic bearing
Opis:
Hydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm. An impact hammer was used to excite vibration of the shaft. The approximation by means of the least squares method was applied to determine bearing dynamic coefficients. Based on the performed research, the four (i.e. two main and two crosscoupled) coefficients of stiffness, damping and mass for each bearing were obtained. The mass coefficients add up to the complex shaft weight. These values are not required for modeling dynamics of the machine because the rotor mass is usually known, however, they may serve as a good indicator to validate the correctness of the stiffness and damping coefficients determined. Additionally, the experimental research procedure was described. The signals of displacements in the bearings and the excitation forces used for determination of the bearing dynamic coefficients were shown. The study discussed in this article is about a rotor supported by two hydrodynamic bearings operating in a nonlinear manner. On the basis of computations, the results of bearing dynamic coefficients were presented for a selected speed.
Źródło:
Polish Maritime Research; 2017, 4; 108-115
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Stability analysis and dynamic behaviour of a flexible asymmetric rotor supported by active magnetic bearings
Autorzy:
Attia Hili, M.
Bouaziz, S.
Haddar, M.
Powiązania:
https://bibliotekanauki.pl/articles/280401.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
asymmetric rotor
finite element
Floquet’s theory
dynamic coefficients
stability
Opis:
The objective of this work is to show the influence of dynamic characteristics of Active Magnetic Bearings (AMBs) on the stability and dynamic response of an asymmetric and unbalanced rotor. Indeed, AMBs have been successfully applied in several industrial machinery facilities. Their main advantages are the contactless working principle, frictionless suspension and operation in very high speeds. Firstly, the AMBs dynamic support parameters have been obtained through electromagnetic theory. Then, a generalized system equations of motion have been derived using the finite element method. The motion of a rotor the shaft cross-section of which is asymmetric is generally governed by ordinary differential equations with periodic coefficients. Floquet’s theory is used to investigate the stability of this system of equations. Finally, numerical simulation results are presented and discussed.
Źródło:
Journal of Theoretical and Applied Mechanics; 2017, 55, 3; 751-763
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania podstawowych parametrów sprzęgieł podatnych
The study of the basic parameters of flexible couplings
Autorzy:
Opasiak, T.
Powiązania:
https://bibliotekanauki.pl/articles/395623.pdf
Data publikacji:
2012
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
sprzęgło podatne
charakterystyka statyczna
charakterystyka dynamiczna
współczynnik sztywności
współczynnik tłumienia
flexible coupling
static characteristic
dynamic characteristic
coefficients of stiffness
coefficients of damping
Opis:
W artykule przedstawiono wyniki badań podstawowych parametrów charakteryzujących sprzęgła podatne. Badania ograniczyły się do wyznaczenia charakterystyk statycznych i dynamicznych. Na podstawie tych charakterystyk odczytano współczynniki sztywności i tłumienia. Badania przeprowadzono na sprzęgłach podatnie skrętnych z łącznikiem oponowym i łącznika w kształcie pierścienia elastycznego.
This article presents a results of study of the basic parameters characterizing the flexible couplings. The study was limited to determine the static and dynamic characteristics. Based on these characteristics read out the coefficientsof stiffness and damping. Tests were conducted on flexible coupling, with a tire rubber coupling and witch a ring rubber coupling.
Źródło:
Postępy Nauki i Techniki; 2012, 12; 122-130
2080-4075
Pojawia się w:
Postępy Nauki i Techniki
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-5 z 5

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies