Temat: cermet coating - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: Microstructure and Properties of TiC/Ti Coatings Deposited by the Supersonic Cold Gas Spray Technique
Autorzy:: Kusiński, J.
Kac, S.
Kowalski, K.
Dosta, S.
Georgiou, E. P.
Garcia-Forgas, J.
Matteazzi, P.
Powiązania:: https://bibliotekanauki.pl/articles/356608.pdf
Data publikacji:: 2018
Wydawca:: Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:: cold gas spraying
Ti
TiC
CerMet coating
SEM
TEM
wear resistance
Opis:: Nanostructured, biocompatible, TiC/Ti Supersonic Cold Gas Sprayed coatings were deposited onto a Ti6Al4V alloy and their microstructure, wear resistance and hardness were investigated. The starting nanostructured powder, containing a varied mixture of Ti and TiC particles, was produced by high energy ball milling. Scanning and transmission electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction were used for structural and chemical analyses of powder particles and coatings. Coatings, 250-350 μm thick, preserving the nanostructure and chemical powder composition, with low porosity and relatively high hardness (~850 HV), were obtained. These nanostructured TiC/Ti coatings exhibited better tribological properties than commonly used biomedical benchmark materials, due to an appropriate balance of hard and soft nano-phases.
Źródło:: Archives of Metallurgy and Materials; 2018, 63, 2; 867-873
1733-3490
Pojawia się w:: Archives of Metallurgy and Materials
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: Comparative Analysis of Mechanical Properties of WC-based Cermet Coatings Sprayed by HVOF onto AZ31 Magnesium Alloy Substrates
Autorzy:: Jonda, Ewa
Łatka, Leszek
Powiązania:: https://bibliotekanauki.pl/articles/2024046.pdf
Data publikacji:: 2021
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:: mechanical properties
microstructure
fracture toughness
indentation test
cermet coating
HVOF spraying
magnesium alloy AZ31
Opis:: Magnesium alloys are very interesting engineering materials due to their very high strength to density ratio (the best among metallic alloys). However, because of low hardness as well as low resistance against erosion, abrasion and corrosion, their applications in the industry is very limited. In order to improve mechanical performances, deposition of hardening coating by thermal spraying was proposed. In this work, the WC-based coatings with different binder (Co or Ni) and co-hardening additives (Cr or Cr3C2) manufactured by high velocity oxy-fuel (HVOF) were studied. These coatings were deposited onto AZ31 magnesium alloy. The crucial problem is obtaining good-adhered coating without damage the substrate, because of relatively low temperature resistance of magnesium alloys (about 300 °C). To solve this problem, HVOF method, which is low temperature and high velocity, was proposed. Also an important role plays process parameters (e.g. spray distance, fuel medium, type of nozzle). The goal of the study was to compare three types of cermet coatings manufactured from commercially available powders (WC-Co, WC-Co-Cr and WC-Cr3C2-Ni) in terms of their microstructure features, microhardness, instrumented indentation and fracture toughness. Results revealed that selected process parameters made it possible to obtain well-adhered coating with good fulfillment of the surface unevenness of the AZ31 substrate. The most noticeable effect was influence of cobalt matrix on higher hardness (1.4 – 1.6 GPa) and Young modulus (330 – 340 GPa) of deposited coatings in compare to the nickel matrix ones (1.2 GPa and 305 GPa, respectively). The same trend was observed in case of fracture toughness, c.a. 6.5 MPa·m1/2 for Co-matrix and 4.9 MPa·m1/2 for Ni-matrix
Źródło:: Advances in Science and Technology. Research Journal; 2021, 15, 2; 57-64
2299-8624
Pojawia się w:: Advances in Science and Technology. Research Journal
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Parametric optimisation of microhardness on heat-treated electroless Ni-YSZ cermet coating
Autorzy:: Bahiyah Baba, N.
Ghazali, A. S.
Abdul Rahman, A. H.
Sharif, S
Powiązania:: https://bibliotekanauki.pl/articles/2172165.pdf
Data publikacji:: 2022
Wydawca:: Stowarzyszenie Komputerowej Nauki o Materiałach i Inżynierii Powierzchni w Gliwicach
Tematy:: full factorial
electroless
Ni-YSZ
cermet
coating
microhardness
treating temperature
treating time
silnia
bezprądowy
powłoka
mikrotwardość
temperatura obróbki
czas obróbki
Opis:: Purpose The paper discusses the parametric optimisation of the electroless Ni-YSZ cermet coating microhardness upon heat treatment. Heat treatment is a process to increase the mechanical properties of the electroless nickel coating and it can be enhanced by manipulating its parameters. Parametric optimisation is conducted by the design of experiment full factorial 3x3 with 27 runs. Treating temperature, treating time and ceramic particle size parameters at 3-level are evaluated using statistical tool ANOVA in Minitab20. Design/methodology/approach Ni-YSZ cermet coating is deposited onto a high-speed steel substrate using the electroless nickel co-deposition method. The temperature and time were varied in a range of 300-400oC and 0-2 hours respectively. The microhardness measurements were carried out using a Vickers microhardness tester (Shimadzu) according to ISO 6507-4. The surface characterisation was analysed using Cambridge Stereoscan 90 Scanning Electron Microscope (SEM) coupled with Energy Dispersive X-ray Analysis (EDXA). Findings The optimum condition in obtaining high microhardness on Ni-YSZ cermet coating is evaluated by statistical tool ANOVA in Minitab20 software. It is found that the most significant parameter for high microhardness is at the treating temperature of 400oC followed by treating time at 2 hours using nano-sized YSZ particles. The ceramic particle size is found not a significant parameter in obtaining a high microhardness, however it has effect on interaction between treating temperature and treating time. Research limitations/implications The paper only limits to the optimisation condition of microhardness on Ni-YSZ cermet coating hardness property by varying heat treatment parameters. Practical implications The optimisation condition obtained might only applicable to the electroless Ni-YSZ cermet coating with similar electroless nickel solution and treatments. Originality/value The value of this work is the heat treatment parametric optimisation to obtain high microhardness on electroless Ni-YSZ cermet coating by using the design of experiment 3-level full factorial.
Źródło:: Journal of Achievements in Materials and Manufacturing Engineering; 2022, 112, 1; 33--41
1734-8412
Pojawia się w:: Journal of Achievements in Materials and Manufacturing Engineering
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: Effect of heat treatment on microhardness of electroless Ni-YSZ cermet coating
Autorzy:: Bahiyah Baba, N.
Ghazali, A. S.
Abdul Rahman, A. H.
Sharif, S.
Powiązania:: https://bibliotekanauki.pl/articles/2201036.pdf
Data publikacji:: 2022
Wydawca:: Stowarzyszenie Komputerowej Nauki o Materiałach i Inżynierii Powierzchni w Gliwicach
Tematy:: Ni-YSZ
cermet
coating
microhardness
heating temperature
heating time
electroless nickel
powłoka
mikrotwardość
temperatura nagrzewania
czas nagrzewania
bezprądowe powlekanie niklem
Opis:: Purpose: The paper discussed the effect of heat treatment on electroless nickel-yttria-stabilised zirconia (Ni-YSZ) cermet coating. Ni-YSZ cermet coating has potential applications such as cutting tools, thermal barriers, solid oxide fuel anode, and various others. The compatibility of ceramic YSZ and metallic nickel in terms of the mechanical properties such as hardness by varying the heating temperature, time and ceramic particle size is highlighted. Design/methodology/approach: Ni-YSZ cermet coating was deposited onto a highspeed steel substrate using the electroless nickel co-deposition method. The temperature and time were varied in a range of 300-400°C and 1-2 hours, respectively. The microhardness measurements were carried out using a Vickers microhardness tester (Shimadzu) according to ISO 6507-4. The surface characterisation of the cermet coating was carried out using JOEL Scanning Electron Microscope (SEM) coupled with Energy Dispersive X-ray (EDX) JSM 7800F. The crystallographic structure of materials was analysed by X-ray diffraction (XRD) Bruker D8 Advance instrument. Findings: It was found that the microhardness of Ni-YSZ cermet coating with the ratio of 70:30, respectively, is directly proportional to the heating temperature and time. Heating the Ni-YSZ cermet coating at 300°C from room temperature (rtp) to 1 hour shows a 12% microhardness increment, while from 1 to 2 hours gives a 19% increment. Compared to heating at 350°C and 400°C, the increment is more significant at 33% and 49% for rtp to 1 hour and 8% and 16% for 1 to 2 hours, respectively. In addition, the effect of varying YSZ particle size in the Ni-YSZ cermet gave response differently for heating temperature and heating time. Research limitations/implications: The paper is only limited to the discussion of the heat treatment effect on Ni-YSZ cermet coating hardness property. The tribological effect will be in future work. Practical implications: The microhardness data may vary due to the Vickers microhardness force applied and the amount of ceramic particle incorporation and phosphorus content in the nickel matrix. Originality/value: The value of this work is the compatibility of the ceramic YSZ and metallic nickel matrix in terms of mechanical properties, such as hardness, upon heat treatment.
Źródło:: Journal of Achievements in Materials and Manufacturing Engineering; 2022, 113, 1; 5--12
1734-8412
Pojawia się w:: Journal of Achievements in Materials and Manufacturing Engineering
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "cermet coating" wg kryterium: Temat

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język