Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "carbon deposit" wg kryterium: Temat


Wyświetlanie 1-2 z 2
Tytuł:
Technology for development of methane-hydrate deposits jointly with receiving fresh water
Autorzy:
Denysov, Y.
Klymenko, V.
Martynenko, V.
Rybicki, Cz.
Powiązania:
https://bibliotekanauki.pl/articles/298671.pdf
Data publikacji:
2017
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
gas hydrates
gas hydrate deposit
methane
carbon dioxide
fresh water
exergy efficiency
economic efficiency
Opis:
The technology of development of bottom gas-hydrate deposits, which allows to receive fresh water simultaneously with methane, is presented. Principal schemes are presented and methods of operation of dualpurpose plants implementing this technology and described on the basis of the methods of gas production from methane hydrates that are most prepared for practical implementation: 1) injection of warm water into the well; 2) depressive effect on the deposit; 3) replacement of methane in hydrates with carbon dioxide injected into the reservoir. The magnitude of the decrease in temperature with the depression effect on the deposit is determined. It is shown that, the amount of fresh water obtained in dual-purpose plants operating with the replacement of methane in hydrates with carbon dioxide is proportional to the coefficient of the recycling rate of CO2. For the considered schemes of dual-purpose plants, processes of decomposition of methane hydrates in the gas-hydrate formation are analyzed, an exergic efficiency estimation is performed. Such installations. The economic efficiency of a single-purpose and dual-purpose gas-producing units operating according to an approved method of depression is considered. It is shown that the most effective are dual-purpose facilities operating using the method of methane replacement in hydrates with carbon dioxide, and the coefficients of economic efficiency of dual-purpose installations are at least 1.2 times higher than similar coefficients of single-purpose gas production facilities.
Źródło:
AGH Drilling, Oil, Gas; 2017, 34, 2; 531-542
2299-4157
2300-7052
Pojawia się w:
AGH Drilling, Oil, Gas
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The modeling of the heat loads in the exhaust valve from and without regard of the carbon deposit
Autorzy:
Jędrusik, D.
Gustof, P.
Powiązania:
https://bibliotekanauki.pl/articles/243988.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
numerical techniques
analysis and modelling of heat loads
valve
carbon deposit
FEM
Opis:
This paper presents the modelling of the heat loads in the exhaust valve from and without regard of carbon deposit in initial phase of work of the turbocharged Diesel engine by using the two-zone combustion model, finite elements method (FES) and program Cosmos/M. In order to illustrate the problem the valve face is divided into two equal areas, then it was assumed that one of them is covered with a thin layer of carbon deposit. Modelling was conducted based on the boundary conditions III kind as a function of time, which describes the convective heat transfer coefficient and the temperature of the surrounding surfaces of valve. As a result of the calculations was compared obtained temperature distribution on the surfaces of the valve - with and without carbon deposit. The study also performed an analysis of the stress distribution that arises in the valve by the presence of the carbon deposit on the surface of the face valve. The analysis showed that the face valve heats up unevenly, more slowly on the side of the carbon deposit. Moreover small increase of the temperature causes the increase of the stress values. Maximum values of stresses do not appear in a valve face under a layer of carbon deposit but on the line distributing the surface covered with carbon deposit and without carbon deposit, near the valve face. These stresses cause the growth of microcracks in the area of the valve face, which finally give occasion to the defect of material, the damage of the valve and engine failure
Źródło:
Journal of KONES; 2010, 17, 3; 173-179
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies