Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "bimetal" wg kryterium: Temat


Wyświetlanie 1-9 z 9
Tytuł:
Structure and Mechanical Properties of Explosive Welded Mg/Al Bimetal
Struktura i właściwości mechaniczne połączenia uzyskanego metodą zgrzewania wybuchowego bimetalu Mg/Al
Autorzy:
Balga, D.
Ostroushko, D.
Saksl, K.
Mazancová, E.
Milković, O.
Powiązania:
https://bibliotekanauki.pl/articles/354953.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
explosive welding
Mg/Al bimetal
micro-hardness
micro-diffraction
PETRA III
zgrzewanie wybuchowe
bimetal Mg/Al
mikrotwardość
mikrodyfrakcja
Opis:
In the article we analyzed shape, local mechanical properties, chemical and phase composition of Magnesium/Aluminium cladded material prepared by explosion welding. In particular we focus our investigation on Mg/Al interface and areas close to the joint. Hardness of the joined materials measured far from their interface is similar for both materials, however in the region of interface the hardness drops down by 40%. Phase transformations in the interface was examined by a hard X-ray micro-diffraction experiment performed at beamline P07 at PETRA III at the energy of 99 keV which helped us identify in Al: fcc-Al, Al2 Cu tetragonal and Al7 Cu2 Fe tetragonal and in Mg: hcp-Mg, Mg2 Si cubic phases. In the interface we haven’t observed any new intermetallics, but computation of lattice parameters and profiles of Al and Mg peaks proved an existence of solid solution with different gradient of chemical composition.
W pracy analizowano kształt, lokalne właściwości mechaniczne, chemiczne oraz składników fazowych Mg/Al materiałów platerowanych otrzymanych metodą zgrzewania wybuchowego. W szczególności, skupiono się na badaniach połączenia fazy Mg/Al oraz obszarów znajdujących się w pobliżu połączenia. Twardość połączonych materiałów badano w znacznej odległości od warstwy samego połączenia, i zauważono, iż jest ona podobna do twardości materiałów wyjściowych, jednakże twardość w regionie warstwy połączenia spada o 40%. Przemiana fazowa w warstwie połączenia została poddana badaniom mikrodyfrakcyjnym, na urządzeniu P07, PETRA III o energii 99 keV, dzięki której zidentyfikowano w Al fazy tetragonalne: fcc-Al, Al2 Cu oraz Al7 Cu2 Fe i w Mg: heksagonalna Mg oraz kubiczna Mg2 Si. W warstwie połączenia nie zaobserwowano żadnych innych nowych faz międzymetalicznych. Obliczone parametry sieci komórki elementarnej i profile pików Al i Mg potwierdzają występowanie roztworu stałego z różnym gardientem składu chemicznego.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 4; 1593-1597
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A generalized upper bound solution for extrusion of bi-metallic rectangular cross-section bars through dies of any shape
Uogólnione rozwiązanie ograniczenia górnego problemu wytłaczania bimetalowych belek o przekroju prostokątnym za pomocą tłoczników o dowolnym kształcie
Autorzy:
Haghighat, H.
Amjadian, P.
Powiązania:
https://bibliotekanauki.pl/articles/279195.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
extrusion
bimetal
plane strain
upper bound method
FEM
Opis:
In this paper, a generalized upper bound solution is developed for extrusion of bi-metallic rectangular cross-section bars through dies of any shape. The internal, shearing and frictional power terms are derived and they are used in the upper bound model. By using the developed upper bound model, the extrusion pressures for two types of die shapes, an optimum wedge shaped die as a linear die profile and an optimum streamlined die shape as a curved die profile, are determined. The corresponding results for those two die shapes are also determined by using the finite element code and compared with the upper bound results. These comparisons show a good agreement.
W pracy wyprowadzono uogólnione rozwiązanie ograniczenia górnego problemu wytłaczania bimetalowych belek o przekroju prostokątnym za pomocą tłoczników o dowolnym kształcie. Wyznaczono wyrażenia potęgowe opisujące wewnętrzne, ścinające oraz tarciowe obciążenia i zastosowano je w modelu matematycznym omawianego zagadnienia. Zaproponowana metoda badań pozwoliła na określenie nacisku podczas wytłaczania elementów przy użyciu dwóch typów tłocznika – optymalnego klinowego o profilu liniowym oraz tłocznika o zarysie krzywoliniowym, opływowym. W obydwu przypadkach obliczenia porównano z wynikami uzyskanymi z metody elementów skończonych. Porównanie to wykazało dobrą zgodność rozwiązania ograniczenia górnego z rezultatami MES.
Źródło:
Journal of Theoretical and Applied Mechanics; 2013, 51, 1; 105-116
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Designing of X46Cr13 Steel Heat Treatment in Condition of Casting Mould
Autorzy:
Przyszlak, Natalia
Piwowarski, Grzegorz
Powiązania:
https://bibliotekanauki.pl/articles/27314161.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czasopisma i Monografie PAN
Tematy:
layered casting
bimetal
high chromium steel
grey cast iron
odlew warstwowy
stal wysokochromowa
żeliwo szare
Opis:
The paper presents issues related to the technology of layered castings manufactured in the system: working part made of high-chromium steel X46Cr13 - base part made of gray cast iron with flake graphite, using the mould cavity preparation technology. Considering the high hardenability of the above-mentioned steel grade, the aim of the research was to optimize the casting parameters of gray cast iron in such a way that it would be possible to perform heat treatment of X46Cr13 steel directly in the casting mould. As part of the research, the geometry of the working and base parts of layered castings was selected, and guidelines for mould technology from the point of view of the moulding sand were developed. In order to control the cooling rate, three matrix of the moulding sand were used - quartz sand, chromite sand and silicon carbide, with the same granularity. The thermal conductivity coefficient of sands made on selected matrix, bound with synthetic resin in the ratio of 30:1, was experimentally determined. Then, the bimetal casting process in a given mass was simulated in the MagmaSoft® (ver. 5.4.1). The purpose of the simulation was to determine the maximum virtual temperature Tm in the thermal center of the outer surface of the X46Cr13 steel insert. From the point of view of the research purpose, the insert was expected to heat up to the austenitization temperature, i.e. at least 950°C.
Źródło:
Archives of Foundry Engineering; 2023, 23, 2; 119--126
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Consecutive Casting of Iron Bimetal with Low-Carbon Steel Interface Plate
Autorzy:
Purwadi, W.
Bandanadjaja, B.
Idamayanti, D.
Lilansa, N.
Powiązania:
https://bibliotekanauki.pl/articles/381199.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
continuous casting
bimetal
white cast iron
casting temperature
interface plate
odlew ciągły
żeliwo białe
temperatura odlewania
Opis:
Consecutive casting of bimetallic applies consecutive sequences of pouring of two materials into a sand mold. The outer ring is made of NiHard1, whereas the inner ring is made of nodular cast iron. To enable a consecutive sequence of pouring, an interface plate made of low carbon steel was inserted into the mold and separated the two cavities. After pouring the inner material at the predetermined temperature and the interface had reached the desired temperature, the NiHard1 liquid was then poured immediately into the mold. This study determines the pouring temperature of nodular cast iron and the temperature of the interface plate at which the pouring of white cast iron into the mold should be done. Flushing the interface plate for 2 seconds by flowing nodular cast iron liquid as inner material generated a diffusion bonding between the inner ring and interface plate at pouring temperatures of 1350°C, 1380°C, and 1410°C. The interface was heated up to a maximum temperature of 1242°C, 1260°C, and 1280°C respectively. The subsequent pouring of white cast iron into the mold to form the outer ring at the interface temperature of 1000°C did not produce a sufficient diffusion bonding. Pouring the outer ring at the temperature of 1430°C and at the interface plate temperature of 1125°C produced a sufficient diffusion bonding. The presence of Fe3O2 oxide on the outer surface of the interface material immediately after the interface was heated above 900⁰C has been identified. Good metallurgical bonding was achieved by pouring the inner ring at the temperature of 1380°C, interface temperature of 1125°C and then followed by pouring of the outer ring at 1430⁰C and flushing time of 7 seconds.
Źródło:
Archives of Foundry Engineering; 2020, 20, 1; 95-104
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ zwilżalności wyżej topliwego podłoża na jakość warstw miedzianych wytwarzanych metodą pośredniego grzania oporowego przy obniżonym ciśnieniu
The influence of high fusible substrate wettability on a quality of cupper films produced by indirect heat resistance method at reduced pressure
Autorzy:
Komorowski, J.
Binienda, M.
Pokrzywa, M.
Just, P.
Wołowiec, E.
Praska-Jaros, A.
Kula, P.
Powiązania:
https://bibliotekanauki.pl/articles/408275.pdf
Data publikacji:
2012
Wydawca:
Politechnika Lubelska. Wydawnictwo Politechniki Lubelskiej
Tematy:
miedź
grzanie oporowe
zwilżalność podłoża
bimetal
topienie pośrednie
copper
heat resistance
surface wettability
bimetals
indirect melting
Opis:
W artykule prezentowane są zagadnienia związane z badaniem wpływu zwilżalności wysokotopliwego podłoża na jakość warstw miedzianych wytwarzanych metodą pośredniego grzania oporowego przy obniżonym ciśnieniu. W pracy przedstawiono wyniki badań przetapiania sproszkowanej miedzi na podłożach metalowych o wyższej temperaturze topnienia niż sam surowiec. Metoda ta może znaleźć zastosowanie przy tworzeniu różnego rodzaju bimetali lub może posłużyć także do kierunkowego oczyszczania przetapianego surowca.
The article presents issues related to examination of the impact of wettability of high fusible substrate on a quality of the copper produced by indirect resistance heating at reduced pressure. This paper presents the results of remelting of powdered copper on metal substrates with melting points higher than those for the raw material. This method can be used to create different types of bimetals and may be used also for directional cleaning of remelted material.
Źródło:
Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska; 2012, 4b; 32-37
2083-0157
2391-6761
Pojawia się w:
Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Identification of Residual Stress Phenomena Based on the Hole Drilling Method in Explosively Welded Steel-Titanium Composite
Identyfikacja naprężeń własnych metodą nawiercania otworu w bimetalu stal-tytan otrzymanego technologią zgrzewania wybuchowego
Autorzy:
Karolczuk, A.
Kowalski, M.
Kluger, K.
Żok, F.
Powiązania:
https://bibliotekanauki.pl/articles/353913.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
explosive welding
residual stresses
bimetallic composite
titanium grade 1
zgrzewanie wybuchowe
naprężenia
bimetal
tytan Grade 1
Opis:
The hole drilling method was used to determine residual stresses in bimetallic composite manufactured by explosive welding process. The analyzed bimetal consist of titanium Grade 1 (6mm) and S355J2+N steel (40mm). The aim of the paper is to establish the influence of the heat treatment on residual stress state in titanium layer. Residual stress calculations were performed according to standards developed by strain gauge manufacturer (TML) and ASTM standards. The main conclusion is the heat treatment considerably changes the residual stress state in titanium layer from tensile stress state (no heat treatment) to compression stress state (after the heat treatment).
W pracy przedstawiono wyniki badań naprężeń resztkowych, wyznaczonych metodą nawiercania, w bimetalu stal-tytan otrzymanego w procesie zgrzewania wybuchowego. Analizowany bimetal to kompozyt stali S355J2+N (40mm) oraz tytanu Grade 1 (6mm). Celem badania było ustalenie wpływu obróbki cieplnej na kierunki i wartości naprężeń własnych w warstwie tytanu. Obliczenia naprężeń resztkowych przeprowadzono przy zastosowaniu: (i) procedury zalecanej przez producenta (TML) zastosowanych rozet tensometrycznych oraz (ii) zaleceń ASTM (American Society for Testing and Materials). W wyniku badań ustalono, że zastosowana obróbka cieplna bimetalu zasadniczo zmienia stan naprężeń własnych w warstwie tytanu. Próbki bez obróbki cieplnej wykazują naprężenia resztkowe rozciągające a w próbkach po obróbce cieplnej panują naprężenia ściskające.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 3; 1119-1123
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ratcheting simulation in a titanium-steel bimetallic plate based on the chaboche hardening model
Autorzy:
Karolczuk, A.
Powiązania:
https://bibliotekanauki.pl/articles/386621.pdf
Data publikacji:
2016
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
ratcheting phenomenon
explosive welding
cyclic loading
the chaboche kinematic hardening model
obciążenie zmęczeniowe
bimetal
model Chaboche'a
Opis:
The paper presents the results of fatigue loading simulation applied to bimetallic model using the Chaboche kinematic hardening rule. Three cases of simulations were performed: (i) without residual stresses; (ii) considering residual stresses and (iii) considering asymmetrical geometry of bimetal, i.e. cross area reducing under tension period of loading. Experimental results exhibit the ratcheting phenomenon in titanium-steel bimetallic specimens. The observed ratcheting phenomenon could be explained by the third case of simulation which is supported by detection of microcracks in the vicinity of welded area.
Źródło:
Acta Mechanica et Automatica; 2016, 10, 4; 265-270
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Theoretical and experimental substantiation of the extraction process with thinning bimetallic tubular elements of dissimilar metals and alloys
Teoretyczne i eksperymentalne uzasadnienie procesu ciągnienia z przerzedzaniem bimetalicznych elementów rurowych z różnych metali i stopów
Autorzy:
Titov, Viacheslav
Mozghovyi, Oleksandr
Borys, Ruslan
Bogomolov, Mykola
Amirgaliyev, Yedilhan
Aitkulov, Zhalau
Powiązania:
https://bibliotekanauki.pl/articles/27315425.pdf
Data publikacji:
2023
Wydawca:
Politechnika Lubelska. Wydawnictwo Politechniki Lubelskiej
Tematy:
deformation
bimetal tubular elements
stretching with thawing
dispersing of mechanical energy
odkształcenie
bimetaliczne elementy rurowe
ciągnienie z przerzedzaniem
rozpraszanie energii mechanicznej
Opis:
The article proposes a scheme of the process of manufacturing bimetallic tubular elements by extraction a cylindrical cup of two dissimilar metals without thinning and extraction with thinning cup. At the same time, in the process of extraction in the heated state, the layers of dissimilar metals and alloys are connected and the desired shape of the product is obtained. A mathematical model of deformation of the process of joint extraction with thinning of two dissimilar metals with heating in a flat deformed state is developed. The influence of the deformation value on the dispersion of mechanical energy by bimetal was revealed.
W artykule zaproponowano schemat procesu wytwarzania bimetalicznych elementów rurowych poprzez ciągnienie cylindrycznego kielicha z dwóch różnych metali bez przerzedzania i ciągnienie z przerzedzaniem kielicha. W procesie ciągnienia w stanie nagrzanym warstwy różnych metali i stopów są łączone i uzyskuje się pożądany kształt produktu. Opracowano matematyczny model odkształcenia procesu wspólnego ciągnienia z przerzedzaniem dwóch różnych metali z ogrzewaniem w płaskim stanie odkształconym. Ujawniono wpływ wartości odkształcenia na rozpraszanie energii mechanicznej przez bimetal.
Źródło:
Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska; 2023, 13, 2; 44--49
2083-0157
2391-6761
Pojawia się w:
Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Theoretical and experimental analysis of the bimetallic ribbed bars steel - steel resistant to corrosion rolling process
Teoretyczna i doświadczalna analiza wytwarzania bimetalowych prętów żebrowanych stal - stal odporna na korozję
Autorzy:
Sawicki, S.
Dyja, H.
Powiązania:
https://bibliotekanauki.pl/articles/354893.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
FEM
bimetal
stal odporna na korozję
walcowanie
modelowanie numeryczne
pręty żebrowane
bimetallic bar
steel-steel resistant to corrosion
hot rolling process
numerical modeling
ribbed bars
Opis:
The paper presents results of theoretical and experimental studies on the process of rolling bimetallic ribbed bars in the finishing pass. The work has determined the effect of the shape of oval preformed strip with a variable clad layer share on the distribution of clad layer thickness in bimetallic ribbed bars rolled in the finishing pass. The theoretical and experimental studies were carried out with the aim of determining the clad layer thickness that will ensure the appropriate corrosion resistance of finished product. A software application, Forge2007Ž, was used for numerical modeling.
W pracy przedstawiono wyniki badań teoretycznych i doświadczalnych procesu walcowania prętów żebrowanych bimetalowych w wykroju gotowym. W pracy określono wpływ kształtu pasma owalnego przedgotowego o różnym udziale warstwy platerującej na rozkład grubości warstwy platerującej w prętach żebrowanych bimetalowych walcowanych w wykroju gotowym. Teoretyczne i doświadczalne badania przeprowadzono w celu określenia grubości warstwy platerującej zapewniającej odpowiednią odporność na korozję gotowego wyrobu. Do modelowania numerycznego wykorzystano program komputerowy Forge2007Ž.
Źródło:
Archives of Metallurgy and Materials; 2012, 57, 1; 61-69
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-9 z 9

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies