Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "austenitic transformation" wg kryterium: Temat


Wyświetlanie 1-9 z 9
Tytuł:
Effect of Heat-treatment Parameters of Cast Iron GJS-X350NiMnCu7-3-2 on its Structure and Mechanical Properties
Autorzy:
Medyński, D.
Janus, A.
Zaborski, S.
Powiązania:
https://bibliotekanauki.pl/articles/381991.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
właściwości mechaniczne
obróbka cieplna
transformacja austenityczna
żeliwo austenityczne
żeliwo Ni-Mn-Cu
mechanical properties
heat treatment
austenitic transformation
austenitic cast iron
cast iron Ni-Mn-Cu
Opis:
The paper presents influence of soaking parameters (temperature and time) on structure and mechanical properties of spheroidal graphite nickel-manganese-copper cast iron, containing: 7.2% Ni, 2.6% Mn and 2.4% Cu. Raw castings showed austenitic structure and relatively low hardness (150 HBW) guaranteeing their good machinability. Heat treatment consisted in soaking the castings within 400 to 600°C for 2 to 10 hours followed by air-cooling. In most cases, soaking caused changes in structure and, in consequence, an increase of hardness in comparison to raw castings. The highest hardness and tensile strength was obtained after soaking at 550°C for 6 hours. At the same time, decrease of the parameters related to plasticity of cast iron (elongation and impact strength) was observed. This resulted from the fact that, in these conditions, the largest fraction of fine-acicular ferrite with relatively high hardness (490 HV0.1) was created in the matrix. At lower temperatures and after shorter soaking times, hardness and tensile strength were lower because of smaller degree of austenite transformation. At higher temperatures and after longer soaking times, fine-dispersive ferrite was produced. That resulted in slightly lower material hardness.
Źródło:
Archives of Foundry Engineering; 2017, 17, 1; 121-126
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of nickel equivalent on austenite transition ratio in Ni-Mn-Cu cast iron
Autorzy:
Janus, A.
Kurzawa, A.
Powiązania:
https://bibliotekanauki.pl/articles/380495.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
austenitic cast iron
nickel equivalent
martensitic transformation
WDS analysis
żeliwo austenityczne
przemiana martenzytyczna
analiza WDS
Opis:
Determined was quantitative effect of nickel equivalent value on austenite decomposition degree during cooling-down castings of Ni-Mn- Cu cast iron. Chemical composition of the alloy was 1.8 to 5.0 % C, 1.3 to 3.0 % Si, 3.1 to 7.7 % Ni, 0.4 to 6.3 % Mn, 0.1 to 4.9 % Cu, 0.14 to 0.16 % P and 0.03 to 0.04 % S. Analysed were castings with representative wall thickness 10, 15 and 20 mm. Scope of the examination comprised chemical analysis (including WDS), microscopic observations (optical and scanning microscopy, image ana-lyser), as well as Brinell hardness and HV microhardness measurements of structural components.
Źródło:
Archives of Foundry Engineering; 2013, 13, 2; 53-58
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Soaking Parameters on the Segregation and Corrosion Resistance of GJS-X350NiMnCu7-3-2 Ductile Iron
Autorzy:
Medyński, D.
Janus, A.
Stachowicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/380330.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat treatment
austenitic ductile iron
transformation of austenite
corrosion resistance
segregation of elements
obróbka cieplna
żeliwo sferoidalne
austenit
odporność na korozję
Opis:
In this paper, the effect of changes the parameters of heat treatment on the structure and the degree of elements segregation was determined, in the context of corrosion resistance of ductile iron Ni-Mn-Cu, containing 7.2% Ni, 2.6% Mn and 2.4% Cu. In the condition after casting, castings of austenitic matrix and 160HBW hardness were obtained. The achieved castings were soaked at 450, 550 and 650°C for 4, 8 and 12 hours, then cooled down at the ambient air. In most cases, the heat treatment resulted in a change in the castings matrix, had the consequence of increasing their hardness in comparison to raw castings. Increasing the temperature and prolonging soaking time resulted in increasing the degree of transformation of austenite, while reducing the degree of elements segregation. This led to the formation of slightly bigger number of pitting due to corrosion, but not so deep and more evenly distributed in comparison to raw castings. Wherein the results of corrosion tests show that heat treatment of castings did not significantly change their corrosion resistance in comparison to raw castings, in contrast to the significant increase in mechanical properties.
Źródło:
Archives of Foundry Engineering; 2017, 17, 2; 69-74
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Abrasive-wear Resistance of Austenitic Cast Iron
Autorzy:
Medyński, D.
Janus, A.
Powiązania:
https://bibliotekanauki.pl/articles/380382.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
abrasive wear
austenitic cast iron
heat treatment
nickel equivalent
transformation of austenite
zużycie ścierne
żeliwo austenityczne
obróbka cieplna
nikiel
transformacja austenitu
Opis:
A research of wear resistance of an austenitic cast iron with higher resistance to abrasive-wear and maintained corrosion resistance characteristic for Ni-Resist cast iron is presented. For the examination, structure of raw castings was first formed by proper selection of chemical composition (to make machining possible). Next, a heat treatment was applied (annealing at 550 °C for 4 hours followed by air cooling) in order to increase abrasive-wear resistance. One of the factors deciding intensity of wear appeared to be the chilling degree of castings. However, with respect to unfavourable influence of chilling on machining properties, an important factor increasing abrasive-wear resistance is transformation of austenite to acicular ferrite as a result of annealing non-chilled castings. Heat treatment of non-chilled austenitic cast iron (EquNi > 16%) resulted in much higher abrasive-wear resistance in comparison to the alloy having pearlitic matrix at ambient temperature (EquNi 5.4÷6.8%).
Źródło:
Archives of Foundry Engineering; 2018, 18, 3; 43-48
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dilatometric Research of High-quality Nodular Cast Iron
Autorzy:
Medyński, D.
Janus, A.
Powiązania:
https://bibliotekanauki.pl/articles/380654.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
alloy cast iron
austenitic cast iron
dilatometric research
martensitic transformation
nickel equivalent
żeliwo stopowe
żeliwo austenityczne
badania dylatometryczne
przemiana martenzytyczna
ekwiwalent niklowy
Opis:
In the research, relationships between matrix structure and hardness of high-quality Ni-Mn-Cu cast iron containing nodular graphite and nickel equivalent value were determined. Nickel equivalent values were dependent on chemical composition and differences between them resulted mostly from nickel concentration in individual alloys. Chemical compositions of the alloys were selected to obtain, in raw condition, austenitic and austenitic-martensitic cast iron. Next, stability of matrix of raw castings was determined by dilatometric tests. The results made it possible to determine influence of nickel equivalent on martensite transformation start and finish temperatures.
Źródło:
Archives of Foundry Engineering; 2018, 18, 2; 163-168
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Chemical Composition on Structure and Corrosion Resistance of Ni-Mn-Cu Cast Iron
Autorzy:
Medyński, D.
Janus, A.
Powiązania:
https://bibliotekanauki.pl/articles/383110.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
corrosion
martensitic transformation
austenitic cast iron
Ni-Mn-Cu cast iron
nickel equivalent
korozja
przemiana martenzytyczna
żeliwo austenityczne
żeliwo Ni-Mn-Cu
Opis:
In the paper, a relationship between chemical composition of Ni-Mn-Cu cast iron and its structure, hardness and corrosion resistance is determined. The examinations showed a decrease of thermodynamic stability of austenite together with decreasing nickel equivalent value, in cast iron solidifying according to both the stable and the metastable systems. As a result of increasing degree of austenite transformation, the created martensite caused a significant hardness increase, accompanied by small decline of corrosion resistance. It was found at the same time that solidification way of the alloy and its matrix structure affect corrosion resistance to a much smaller extent than the nickel equivalent value, in particular concentration of elements with high electrochemical potential.
Źródło:
Archives of Foundry Engineering; 2016, 16, 3; 59-62
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Nickel Equivalent on Structure and Corrosion Resistance of Nodular Cast Iron Ni-Mn-Cu
Autorzy:
Medyński, D.
Janus, A.
Powiązania:
https://bibliotekanauki.pl/articles/381447.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
austenitic nodular cast iron
cast iron Ni-Mn-Cu
nickel equivalent
martensitic transformation
corrosion
żeliwo sferoidalne
żeliwo Ni-Mn-Cu
nikiel
przemiany martenzytyczne
korozja
Opis:
Within the research determined was the effect of nickel equivalent on structure, hardness and corrosion resistance of nodular cast iron Ni- Mn-Cu. The examinations revealed a drop of thermodynamic stability of austenite along with decreasing nickel content. Along with in-creasing degree of austenite transformation, the created martensite resulted in significant increase of hardness (and of abrasion resistance as well) of the examined of cast iron, accompanied by insignificant decrease of corrosion resistance.
Źródło:
Archives of Foundry Engineering; 2015, 15, 1 spec.; 69-74
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Cr, Mo and Al on Structure and Selected Mechanical Properties of Austenitic Cast Iron
Autorzy:
Medyński, D.
Janus, A.
Powiązania:
https://bibliotekanauki.pl/articles/383202.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
austenitic cast iron
austenite transformation
heat treatment
cast
mechanical properties of cast
nickel equivalent
żeliwo austenityczne
zmiana właściwości
obróbka cieplna
odlew
właściwości mechaniczne odlewu
Opis:
Results of a research on influence of chromium, molybdenum and aluminium on structure and selected mechanical properties of Ni-Mn- Cu cast iron in the as-cast and heat-treated conditions are presented. All raw castings showed austenitic matrix with relatively low hardness, making the material machinable. Additions of chromium and molybdenum resulted in higher inclination to hard spots. However, a small addition of aluminium slightly limited this tendency. Heat treatment consisting in soaking the castings at 500 °C for 4 h resulted in partial transformation of austenite to acicular, carbon-supersaturated ferrite, similar to the bainitic ferrite. A degree of this transformation depended not only on the nickel equivalent value (its lower value resulted in higher transformation degree), but also on concentrations of Cr and Mo (transformation degree increased with increasing total concentration of both elements). The castings with the highest hard spots degree showed the highest hardness, while hardness increase, caused by heat treatment, was the largest in the castings with the highest austenite transformation degree. Addition of Cr and Mo resulted in lower thermodynamic stability of austenite, so it appeared a favourable solution. For this reason, the castings containing the highest total amount of Cr and Mo with an addition of 0.4% Al (to reduce hard spots tendency) showed the highest tensile strength.
Źródło:
Archives of Foundry Engineering; 2019, 4; 39-44
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Austenite Transformation on Abrasive Wear and Corrosion Resistance of Spheroidal Ni-Mn-Cu Cast Iron
Autorzy:
Medyński, D.
Janus, A.
Powiązania:
https://bibliotekanauki.pl/articles/381837.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
abrasive wear
corrosion resistance
austenitic cast iron
Ni-Mn-Cu cast iron
martensitic transformation
odporność na korozję
żeliwo austenityczne
żeliwo Ni-Mn-Cu
przemiana martenzytyczna
Opis:
Within the presented work, the effect of austenite transformation on abrasive wear as well as on rate and nature of corrosive destruction of spheroidal Ni-Mn-Cu cast iron was determined. Cast iron contained: 3.1÷3.4 %C, 2.1÷2.3 %Si, 2.3÷3.3 %Mn, 2.3÷2.5 %Cu and 4.8÷9.3 %Ni. At a higher degree of austenite transformation in the alloys with nickel equivalent below 16.0%, abrasive wear resistance was significantly higher. Examinations of the corrosion resistance were carried out with the use of gravimetric and potentiodynamic method. It was shown that higher degree of austenite transformation results in significantly higher abrasive wear resistance and slightly higher corrosion rate, as determined by the gravimetric method. However, results of potentiodynamic examinations showed creation of a smaller number of deep pinholes, which is a favourable phenomenon from the viewpoint of corrosion resistance.
Źródło:
Archives of Foundry Engineering; 2016, 16, 3; 63-66
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-9 z 9

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies