Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "austenitic nodular cast iron" wg kryterium: Temat


Wyświetlanie 1-3 z 3
Tytuł:
Fatigue Resistance and Other Utility Properties of NiMn-Type of Austenitic Nodular Cast Iron
Autorzy:
Vaško, Alan
Uhríčik, Milan
Kaňa, Václav
Powiązania:
https://bibliotekanauki.pl/articles/27707054.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czasopisma i Monografie PAN
Tematy:
Ni-Resist
austenitic nodular cast iron
EN-GJSA-XNiMn13-7
fatigue
push-pull loading
Opis:
The aim of this paper is to evaluate the fatigue resistance of austenitic nodular cast iron and to compare it with other types of nodular cast irons. The austenitic nodular cast iron, used for the experiments, was alloyed by 13% nickel and 7% manganese (EN-GJSA-XNiMn13-7) to obtain an austenitic matrix. The microstructure was studied using light metallographic microscopy. Mechanical properties were investigated by tensile test, impact bending test and Brinell hardness test. Fatigue tests were carried out at sinusoidal cyclic push-pull loading at ambient temperature. The results of fatigue tests were compared with the fatigue properties of ferrite-pearlitic nodular cast iron and pearlite-ferritic nodular cast iron. Experimental results show that NiMn-type of austenitic nodular cast iron has lower tensile strength and hardness, but higher elongation and absorbed energy than the compared types of nodular cast iron. However, austenitic nodular cast iron has lower fatigue limit.
Źródło:
Archives of Metallurgy and Materials; 2023, 68, 2; 563--569
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Nickel Equivalent on Structure and Corrosion Resistance of Nodular Cast Iron Ni-Mn-Cu
Autorzy:
Medyński, D.
Janus, A.
Powiązania:
https://bibliotekanauki.pl/articles/381447.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
austenitic nodular cast iron
cast iron Ni-Mn-Cu
nickel equivalent
martensitic transformation
corrosion
żeliwo sferoidalne
żeliwo Ni-Mn-Cu
nikiel
przemiany martenzytyczne
korozja
Opis:
Within the research determined was the effect of nickel equivalent on structure, hardness and corrosion resistance of nodular cast iron Ni- Mn-Cu. The examinations revealed a drop of thermodynamic stability of austenite along with decreasing nickel content. Along with in-creasing degree of austenite transformation, the created martensite resulted in significant increase of hardness (and of abrasion resistance as well) of the examined of cast iron, accompanied by insignificant decrease of corrosion resistance.
Źródło:
Archives of Foundry Engineering; 2015, 15, 1 spec.; 69-74
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Using cored wire injection method in the production of austenitic high Ni-alloyed ductile iron castings
Wykorzystanie metody przewodów elastycznych do produkcji odlewów z wysokoniklowego żeliwa plastycznego o osnowie austenitycznej
Autorzy:
Guzik, E.
Wierzchowski, D.
Powiązania:
https://bibliotekanauki.pl/articles/356457.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
treatment ladle
magnesium-cored wire
nodular cast iron
austenitic matrix
magnesium recovery
kadź bębnowa
żeliwo sferoidalne
żeliwo sferoidalne austenityczne
matryca austenityczna
odzysk magnezu
Opis:
Below are described results of the analysis concerning the use of two cored wire injection method (2PE- 9) and the unique application of a drum ladle as a treatment, transport and casting one, instead of a vertical treatment ladle. Parameter optimization, like: length of nodulariser wire, residual magnesium content, treatment and pouring temperature have been shown. Influence of various treatment temperatures, magnesium-cored wire velocities (Mg-treatment times) and weights of molten alloy on magnesium recovery are demonstrated. Moreover, graphite nodule content in relation to different raw materials in the charge mix are presented. Typical microstructure, mechanical properties and treatment costs are given as well. Using specific industrial conditions for tests and optimal, low scrap production of austenitic nodular cast iron (EN-GJSA-XNiSiCr35-5-2 Grade, according with EN 13835), makes this innovative method very credible. Injection of two Ø 9 mm wires; cored in FeSi + Mg nodulariser mixture and inoculant master alloy into a drum ladle is a treatment method that can be used for the production of ductile iron melted in a coreless induction furnace.
W artykule przedstawiono analizę wyników badań otrzymanych podczas produkcji żeliwa sferoidalnego, z zastosowaniem nowej metody sferoidyzacji metalu w kadzi bębnowej (w miejsce powszechnie stosowanej kadzi smukłej), przy użyciu dwóch przewodów elastycznych (technika nazwana umownie jako 2PE - 9). Kadź bębnowa z ciekłym sferoidyzowanym metalem, jest wykorzystywana do transportu ciekłego stopu i zalewania form odlewniczych. Zaprezentowano wyniki badań w zakresie optymalizacji parametrów procesu, takich jak: długości przewodu sferoidyzujacego, krytycznej zawartość magnezu, temperatury zabiegu i temperatury zalewania. Pokazano wpływ temperatury zabiegu, prędkości przemieszczania przewodu sferoidyzującego (czasu zabiegu sferoidyzowania) i masy ciekłego stopu na uzysk magnezu ze sferoidyzatora. Określono liczbę wydzieleń globularnej eutektyki grafitowej w zależności od stosowanych materiałów wsadowych. Przedstawiono mikrostrukturę wysokoniklowego, austenitycznego żeliwa sferoidalnego (zgodnie z norma PN-EN 13835, gatunku EN-GJSA-XNiSiCr35-5-2), jego właściwości mechaniczne oraz koszt obróbki pozapiecowej przy zastosowaniu metody 2PE - 9. Przeprowadzone badania zabiegu sferoidyzowania metalu bezpośrednio w warunkach przemysłowych, pozwoliły zminimalizowac wielkość braków odlewów i potwierdziły innowacyjnosc tej techniki obróbki pozapiecowej. Wprowadzenie dwóch przewodów elastycznych o średnicy Ø 9 mm; jeden wypełniony mieszanina FeSi + Mg, a drugi modyfikatorem grafityzującym, do zabiegowej kadzi bebnowej, jest nowa metoda obróbki pozapiecowej, która może być wykorzystana do produkcji żeliwa sferoidalnego.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 3; 969-972
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies