Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Fe-Al" wg kryterium: Temat


Tytuł:
Assessment of Chemical Composition of Bushgrass (Calamagrostis epigejos L.) Occurring on the Landfill Site of the Furnace Waste and Carbide Residue Lime. Part 2. Content of Iron, Cobalt Manganese, Aluminium and Silicon
Ocena składu chemicznego trzcinnika piaskowego (Calamagrostis epigejos L.) występującego na składowiskach odpadów paleniskowych i wapna pokarbidowego. Cz. 2. Zawartość żelaza, kobaltu, manganu, glinu i krzemu
Autorzy:
Antonkiewicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/387773.pdf
Data publikacji:
2010
Wydawca:
Towarzystwo Chemii i Inżynierii Ekologicznej
Tematy:
trzcinnik piaskowy (Calamagrostis epigejos L.)
składowiska
popioły paleniskowe
wapno pokarbidowe
Fe
Co
Mn
Al
Si
Calamagrostis epigejos L.
dumps
lime carbide
Opis:
Furnace ashes and carbide lime deposited on landfills may constitute a valuable raw material, among others for biological reclamation of post-industrial areas. Their environmental management requires the assessment of their suitability not only with respect to concentrations of heavy metals but also other components, including microelements. Ashes originating from hard coal burning are a rich source of microelements, particularly Fe, B, Mn and Co, which is very important for correct growth. However, very high contents of microelements in furnace wastes may influence their excessive uptake by plants, which in consequence lead to their die-back. Although high accumulation of microelements in plants is not always toxic for the plants themselves, it may cause serious pathogenic consequences in people or animals consuming these plants.
Zdeponowane na składowiskach popioły paleniskowe i wapno pokarbidowe mogą stanowić cenny surowiec m.in. w biologicznej rekultywacji terenów poprzemysłowych. Ich wykorzystanie w środowisku wymaga oceny przydatności pod względem zawartości nie tylko metali ciężkich, ale także innych składników, w tym mikroelementów. Popioły pochodzące ze spalania węgla kamiennego stanowią bogate źródło mikroelementów, zwłaszcza Fe, B, Mn i Co, mających bardzo duże znaczenie w prawidłowym wzroście. Jednakże bardzo duże zawartości mikroelementów w odpadach paleniskowych mogą powodować nadmierne ich pobieranie przez rośliny, co w konsekwencji prowadzi do ich obumierania. Aczkolwiek duże nagromadzenie mikroelementów w roślinach nie zawsze jest toksyczne dla samych roślin, ale może spowodować groźne następstwa chorobowe u ludzi lub zwierząt spożywających te rośliny. Zawartość wybranych pierwiastków w trzcinniku piaskowym zebranym ze składowisk odpadów paleniskowych i wapna pokarbidowego była zróżnicowana i wahała się w zakresie: 49,70-1800,0 mg Fe; 0,01-1,17 mg Co; 7,33-146,0 mg Mn; 17,20-120,0 mg Si oraz 8,68-1500,0 mg Al o kg-1 s.m. Większe zawartości żelaza, kobaltu, manganu i glinu stwierdzono w roślinności zebranej ze składowisk popiołów paleniskowych, a mniejsze z kwatery wapna pokarbidowego. Optymalna zawartość mikroelementów w roślinach przeznaczonych na paszę wynosi: 40-70 mg Fe; 0,3-1,0 mg Co i 40-60 mg Mn o kg-1 s.m. Wyceniając rośliny według tego kryterium, stwierdzono ponadnormatywną zawartość żelaza w próbkach zebranych ze składowiska popiołów paleniskowych nieczynnej kwatery. Natomiast zawartość żelaza w roślinności zebranej ze składowiska wapna pokarbidowego mieściła się w granicach wartości optymalnej. Optymalną zawartość kobaltu stwierdzono w roślinności zebranej z nieczynnej kwatery popiołów paleniskowych, a niedoborową z kwatery czynnej popiołów paleniskowych oraz wapna pokarbidowego. W badaniach własnych stwierdzono niedoborową zawartość manganu (< 40 mg o kg-1) w 13 próbkach pobranych z czaszy składowisk popiołów paleniskowych i wapna pokarbidowego. Tylko w 6 próbkach roślin zawartość manganu przekraczała wartość optymalną. Zawartość manganu w roślinności zebranej z pólek składowisk mieściła się poniżej wartości optymalnej. Małą zawartość manganu w roślinności pobranej ze składowisk, w porównaniu z innymi mikroelementami, można uzasadnić tym, że w środowisku alkalicznym pierwiastek ten tworzy połączenia, z których jest trudno dostępny dla roślin.
Źródło:
Ecological Chemistry and Engineering. A; 2010, 17, 4-5; 359-368
1898-6188
2084-4530
Pojawia się w:
Ecological Chemistry and Engineering. A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of adding furnace ash from bituminous coal combustion to soil on phytoavailability of selected metals
Wpływ dodatku popiołu paleniskowego z węgla kamiennego do gleby na fitoprzyswajalność wybranych metali
Autorzy:
Antonkiewicz, J.
Jasiewicz, C.
Kępka, W.
Kowalewska, A.
Pełka, R.
Losak, T.
Hlusek, J.
Powiązania:
https://bibliotekanauki.pl/articles/296897.pdf
Data publikacji:
2015
Wydawca:
Politechnika Częstochowska. Wydawnictwo Politechniki Częstochowskiej
Tematy:
ash
Cr
Mn
Fe
Ni
Cu
Al
maize
tolerance index
metal translocation factor
metal content
metal uptake
popiół
kukurydza
indeks tolerancji plonu
wskaźnik translokacji metali
zawartość metali
pobranie metali
Opis:
The research on the effect of furnace ash from bituminous coal combustion on the uptake of Cr, Cu, Ni, Fe, Mn, Al by maize (Zea mays L.) was conducted under conditions of a three-year pot experiment. The arable soil in the pot experiment was amended with furnace ash in the amount of 23.33 g·pot‒1 (corresponding to 20 t·ha‒1) and with increasing doses of cadmium (3÷15 mg·kg‒1 soil DM). Application of ash and cadmium in the amount of 3÷5 mg·kg‒1 DM to the soil had a significant effect on the increase in the yield of above-ground parts and roots of maize. Application of subsequent doses of cadmium (7.5÷15 mg·kg‒1) caused a considerable reduction in the yield of the tested plant. The research shows that the applied furnace ash reduced the depression in yielding of maize. Introduction of furnace ash to cadmium-contaminated soil caused an increase in the content of Cr, Fe, Ni, Cu and Al in maize biomass and a decrease in the content of Mn in maize. Among the studied metals, Mn was translocated from roots to above-ground parts the most efficiently, and Al - the least efficiently, evidence of which are the highest values of the translocation factor for Mn, and the lowest values for Al. The research showed that ash introduced to cadmium-contaminated soil did not immobilize the above-mentioned metals, and thereby did not reduce the phytoavailability. In general, contamination of the soil with cadmium and introduction of ash stimulated uptake of the metals by maize. We observed that roots took up more Cr, Fe, Ni and Al, whereas above-ground parts of maize took up more Mn and Cu. The lowest uptake of the studied metals by maize was observed in the treatment where only furnace ash was applied.
Badania nad wpływem popiołu paleniskowego z węgla kamiennego na pobieranie Cr, Cu, Ni, Fe, Mn, Al przez kukurydzę (Zea mays L.) przeprowadzono w warunkach trzyletniego doświadczenia wazonowego. W doświadczeniu wazonowym zastosowano do gleby uprawnej popiół paleniskowy, w ilości 23,33 g·wazon‒1, odpowiadającej 20 t·ha‒1, oraz wzrastające dawki kadmu, w ilości 3÷15 mg·kg‒1 s.m. gleby. Zastosowanie popiołu oraz kadmu w ilości 3÷5 mg·kg‒1 s.m. do gleby wpłynęło istotnie na zwiększenie plonu części nadziemnych i korzeni kukurydzy. Natomiast zaaplikowanie kolejnych dawek kadmu (7,5÷15 mg·kg‒1) spowodowało istotne obniżenie plonu testowanej rośliny. Z badań wynika, że zaaplikowany popiół paleniskowy zmniejszył depresję plonowania kukurydzy. Wprowadzenie popiołu paleniskowego do gleby zanieczyszczonej kadmem wpłynęło na zwiększenie zawartości Cr, Fe, Ni, Cu i Al w biomasie kukurydzy, natomiast wpłynęło na zmniejszenie zawartości Mn w kukurydzy. Spośród badanych metali najłatwiej był przemieszczany z korzeni do części nadziemnych Mn, a najsłabiej Al, o czym świadczą największe wartości współczynnika translokacji dla Mn, a najmniejsze wartości dla Al. Z badań wynika, że popiół wprowadzony do gleby zanieczyszczonej kadmem nie wpłynął na immobilizację wyżej wymienionych metali, a tym samym nie ograniczył fitoprzyswajalności. Generalnie zanieczyszczenie gleby kadmem i wprowadzenie popiołu stymulowało pobieranie metali przez kukurydzę. Stwierdzono większe pobranie Cr, Fe, Ni i Al przez korzenie, natomiast Mn i Cu przez części nadziemne kukurydzy. Najmniejsze pobranie badanych metali przez kukurydzę zarejestrowano w obiekcie, w którym zastosowano wyłącznie popiół paleniskowy.
Źródło:
Inżynieria i Ochrona Środowiska; 2015, 18, 4; 405-422
1505-3695
2391-7253
Pojawia się w:
Inżynieria i Ochrona Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of fly ashes and sewage sludge on Fe, Mn, Al, Si and Co uptake by grass mixture
Autorzy:
Antonkiewicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/125129.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
fly ashes
municipal sewage sludge
grass mixture
yield
Fe
Mn
Al
Si
Co
uptake
quantitative ratios
Opis:
Application of sewage sludge for environmental management of fly ashes landfill site affects chemical composition of plants. The aim of the present investigations was learning the effect of growing doses of municipal sewage sludge on the yield and uptake of Fe, Mn, Al, Si and Co by grass mixture used for environmental management of fly ashes landfill. The experimental design comprised of 5 objects differing by a dose of municipal sewage sludge supplied per 1 hectare: I. control, II. 25 t d.m., III. 50 t d.m., IV. 75 t d.m. and V. 100 t d.m. Application of sewage sludge resulted in the increase in yield. The content of analyzed elements in the grass mixture depended significantly on sewage sludge dose. Increasing doses of sewage sludge caused marked increase in Mn and Co contents, while they decreased Fe, Al and Si contents in the grass mixture. It was found that growing doses of sewage sludge caused an improvement of Fe to Mn ratio value in the grass mixture. Assessing the element content in the grass mixture in the view of forage value, it was found that Fe and Mn content did not meet the optimal value. Si content in plants was below the optimal value.
Źródło:
Journal of Ecological Engineering; 2014, 15, 3; 6-13
2299-8993
Pojawia się w:
Journal of Ecological Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of annealing conditions on changes of the structure and selected properties of Al88Y7Fe5 and Al88Y6Fe6 alloys
Autorzy:
Babilas, Rafał
Spilka, Monika
Łoński, Wojciech
Radoń, Adrian
Kądziołka-Gaweł, Mariola
Gębara, Piotr
Powiązania:
https://bibliotekanauki.pl/articles/2204524.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Al-Y-Fe metallic glasses
heat treatment
structural tests
corrosion resistance
magnetic properties
szkło metaliczne Al-Y-Fe
obróbka cieplna
test strukturalny
odporność na korozję
właściwości magnetyczne
Opis:
Al-Y-Fe amorphous and nanocrystalline alloys are characterized by a unique collection of diverse properties that are influenced by various factors, including heat treatment. In this paper, the effect of heat treatment on the structural changes and selected properties of Al-Y-Fe metallic glasses in the as-spun state is investigated. The structure of the Al88Y7Fe5 and Al88Y6Fe6 alloys was examined by X-ray diffraction (XRD) and Mössbauer spectroscopy (MS). The corrosion resistance of the samples was characterized using polarization tests in a 3.5% NaCl solution at 25 °C. The effect of sodium chloride on the surface was studied with scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). The magnetic properties of Al-based alloys were explored using a vibrating sample magnetometer (VSM). It was revealed that the tested alloys show better properties after annealing than in the as-spun state. The annealing of the Al88Y7Fe5 and Al88Y6Fe6 alloys in the temperature range of 200 to 300 °C improved the magnetic properties and corrosion resistance of these materials. After 3,600 s, the better EOCP values were recorded for the Al88Y6Fe6 and Al88Y7Fe5 alloys after annealing at 300 °C and 200 °C, adequately. On the basis of the polarization tests, it was concluded that the electrochemical properties are better for Al88Y6Fe6 alloys after annealing at 300 °C.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2023, 71, 2; art. no. e144614
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the Wear of an Fe-Al Alloy Turbocharger Rotor Seal Ring under Selected Operating Conditions
Ocena zużycia pierścienia uszczelniającego wirnika turbosprężarki wykonanego ze stopu Fe-Al w wybranych warunkach eksploatacji
Autorzy:
Bąkowski, Henryk
Cebulski, Janusz
Ćwiek, Janusz
Powiązania:
https://bibliotekanauki.pl/articles/27310172.pdf
Data publikacji:
2023
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
wear abrasive
turbocharger rotor seal ring
Fe-Al alloy
zużywanie ścierne
pierścień uszczelniający wirnika turbosprężarki
stop Fe-Al
Opis:
This publication presents the possibility of extending the service life of the rotor shaft seal ring in an automotive turbocharger by using an intermetallic Al-Fe alloy. Comprehensive results of tribological, metallographic and profilometric tests of this alloy (vacuum cast) operating in a sliding association on a T-05 bench allowed the representation of a real friction node. Based on empirical tests, it will be possible to determine which alloy (Al-Fe alloy or the one currently used for sealing rings of a car turbocharger rotor shaft) has better tribological properties. For this purpose, the research was based on an experiment that assumes three main factors determining the wear of the tested association. The result of the experimental plan was to obtain threedimensional diagrams showing the influence of the wear factors on the friction force and surface topography.
W publikacji przedstawiono możliwość wydłużenia czasu eksploatacji pierścienia uszczelniającego wałka wirnika w turbosprężarce samochodowej poprzez zastosowanie międzymetalicznego stopu Al-Fe. Kompleksowe wyniki badań tribologicznych, metalograficznych oraz profilometrycznych tego stopu (odlewanego próżniowo) pracującego w skojarzeniu ślizgowym na stanowisku T-05 pozwoliły na odzwierciedlenie rzeczywistego węzła tarcia. Na podstawie przeprowadzonych badań empirycznych będzie można stwierdzić, który ze stopów (stop Al-Fe czy obecnie stosowany na pierścienie uszczelniające wałka wirnika turbosprężarki samochodowej) posiada lepsze właściwości tribologiczne. W tym celu badania oparto na eksperymencie, który zakłada trzy główne czynniki decydujące o zużyciu badanego skojarzenia. W wyniku przeprowadzonego planu eksperymentu możliwe było uzyskanie wykresów trójwymiarowych ujmujących wpływ czynników eksploatacyjnych na siłę tarcia oraz topografię powierzchni.
Źródło:
Tribologia; 2023, 1; 19--26
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Cumulative Plastic Deformation on Microstructure of the Fe-Al Intermetallic Phase Base Alloy
Wpływ skumulowanego odkształcenia plastycznego na strukturę stopów Fe-Al na osnowie faz międzymetalicznych
Autorzy:
Bednarczyk, I.
Kuc, D.
Niewielski, G.
Powiązania:
https://bibliotekanauki.pl/articles/350991.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
FeAl alloy
Max train simulator
cumulative plastic deformation
microstructure
stop Fe-Al
symulator MaxStrain
skumulowane odkształcenie plastyczne
mikrostruktura
Opis:
This article is part of the research on the microstructural phenomena that take place during hot deformation of intermetallic phase-based alloy. The research aims at design an effective thermo - mechanical processing technology for the investigated intermetallic alloy. The iron aluminides FeAl have been among the most widely studied intermetallics because their low cost, low density, good wear resistance, easy of fabrication and resistance to oxidation and corrosion. There advantages create wide prospects for their industrial applications for components of machines working at a high temperature and in corrosive environment. The problem restricting their application is their low plasticity and their brittle cracking susceptibility, hampers their development as construction materials. Consequently, the research of intermetallic-phase-based alloys focuses on improvement their plasticity by hot working proceses. The study addresses the influence of deformation parameters on the structure of an Fe-38% at. Al alloy with Zr, B Mo and C microadditions, using multi – axis deformation simulator. The influence of deformation parameters on microstructure and substructure was determined. It was revealed that application of cumulative plastic deformation method causes intensive reduction of grain size in FeAl phase base alloy.
Prezentowana praca stanowi element prowadzonych badań nad możliwością kształtowania stopów na osnowie faz międzymetalicznych z układu Fe-Al drogą obróbki cieplno-plastycznej. Związki międzymetaliczne są traktowane jako przyszłościowe materiały do pracy w wysokich temperaturach i agresywnych środowiskach korozyjnych. Zainteresowanie tą grupą materiałową jest spowodowane dobrymi właściwościami użytkowymi: dobrą odpornością na utlenianie i korozję w środowisku wody morskiej, zużycie ścierne. Ponadto niskie koszty materiałowe stwarzają perspektywy do zastosowań jako alternatywę dla stali odpornych na korozję. Ograniczeniem możliwości szerokiego zastosowania intermetalików z układu Fe-Al, jest ich niedostateczna plastyczność, będąca czynnikiem hamującym ich dalszy rozwój jako materiałów konstrukcyjnych. Stąd badania nad możliwością poprawy plastyczności droga obróbki cieplno-plastycznej. W artykule analizowano wpływ parametrów odkształcania na mikrostrukturę stopu Fe-38% at. Al z mikododatkami cyrkonu, molibdenu, boru węgla. Z wykorzystaniem symulatora Maxstrain, który umożliwa kumulację dużych odkształceń w materiale. Przeprowadzono badania mikrostuktury i substruktury wykazały istotny wpływ odkształcania tą metodą na rozdrobnienie ziarn w badanym stopie.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 3; 987-991
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Plasticity of low aluminum alloys from Fe-Al system
Plastyczność niskoaluminiowych stopów z układu Fe-Al
Autorzy:
Bednarczyk, I.
Jabłońska, M.
Powiązania:
https://bibliotekanauki.pl/articles/354642.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stopy Fe-Al
próba ściskania na gorąco
mikrostruktura
substruktura
Fe-Al alloys
hot compression test
microstructure
substructure
Opis:
Alloys based on intermetallic phases from the Fe-Al system they belong to a group of high-temperature creep resisting materials of advantageous physicochemical and mechanical properties at an elevated and high temperature. In general, limitation on the capacity for a broad application of intermetals from the Fe-Al system, e.g. as an alternative to expensive alloy steels of specific properties, is their insufficient plasticity, which is a factor inhibiting further their development as constructional materials. The aim of this work is study about the analysis of the influence of hot deformation parameters like a temperature and strain rate on the plasticity and structure changes in alloys on the base Fe-Al system. These alloys are competitive for their cost and properties in comparison with stainless and acid resistance steels. Were analyzed the properties determined in hot compression test of cast alloys Fe-28Al, Fe-28Al-5Cr, contain microelements Mo, Zr, C, B. The tests were carried out on the range of temperature 700°C - 1100°C with strain rate 0,1 s-1. The results indicated that the Cr addition had an positively effect on the plasticity properties. Moreover exhibited that the Cr addition had an influence on the mechanism of the rebuilding the structure changes.
Stopy na osnowie faz międzymetalicznych z układu Fe-Al, zaliczane są do grupy tworzyw żarowytrzymałych, posiadających korzystne właściwości fizykochemiczne i mechaniczne. Zasadniczym problemem ograniczającym ich powszechne stosowanie jest niska plastyczność i skłonność do kruchego pękania co powoduje zahamowanie w dalszym rozwoju jako materiałów konstrukcyjnych. Celem tej pracy jest ocean wpływu parametrów takich jak temperatura, prędkość odkształcenia na plastyczność i zmiany struktury stopów z układu Fe-Al. Ze względu na niski koszt oraz właściwości są konkurencyjne w porównaniu do stali nierdzewnych i kwasoodpornych. Analizowano właściwości w próbie ściskania na gorąco dla odlewniczych stopów Fe-28Al, Fe-28Al-5Cr, zawierających mikrododatki Mo, Zr, C, B. Próby były prowadzone w zakresie temperatury 700 ÷ 1100°C z prędkością odkształcenia 0,1 s-1. Wyniki wskazują, że mikrododatek Cr ma zdecydowany wpływ na właściwości plastyczne. Dodatkowo mikrododatek Cr ma wpływ na zmianę mechanizmu odbudowy struktury.
Źródło:
Archives of Metallurgy and Materials; 2012, 57, 1; 271-276
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania plastometryczne i mikrostrukturalne stopów Fe-28Al-Cr i Fe-38Al
Plastometric and microstructure tests of alloys Fe-28Al-Cr and Fe-38Al
Autorzy:
Bednarczyk, Iwona
Powiązania:
https://bibliotekanauki.pl/articles/211594.pdf
Data publikacji:
2019
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Obróbki Plastycznej
Tematy:
stopy z układu Fe-Al
mikrostruktura
próba osiowosymetrycznego ściskania
procesy odbudowy struktury
Fe-Al intermetallic phase-based alloys
microstructure
axial-symmetric compression test
structure recovery processes
Opis:
Stopy na bazie uporządkowanych faz międzymetalicznych, tzw. intermetaliki, należą do grupy materiałów metalicznych o właściwościach pośrednich pomiędzy metalami a ceramiką. Szczególne zainteresowanie ze względu na korzystne właściwości znalazły stopy na osnowie faz międzymetalicznych Fe3Al i FeAl z układu Fe-Al. W artykule przedstawiono wpływ parametrów odkształcenia plastycznego na zmiany mikrostruktury stopów z układu Fe-Al. Odkształcenie realizowano w próbie osiowosymetrycznego ściskania na symulatorze Gleeble 3800, przy temperaturze w zakresie od 600 do 1200oC, z prędkością odkształcenia 0,1, 1,0 i 10,0 s-1. Na podstawie zależności naprężenia uplastyczniającego od odkształcenia wyznaczono maksymalne wartości naprężenia uplastyczniającego oraz odkształcenia odpowiadającemu temu naprężeniu w zależności od temperatury i prędkości odkształcenia. W celu obliczenia wartości parametru Zenera-Hollomona Z, czyli skorygowanej ze względu na temperaturę prędkości odkształcenia obliczono energię aktywacji Q procesu odkształcenia plastycznego. Przeprowadzono analizę mikrostruktury z użyciem mikroskopii świetlnej i elektronowej stopów Fe-28Al-5Cr i Fe-38Al w stanie odlewanym i po wyżarzaniu ujednorodniającym oraz po osiowosymetrycznym ściskaniu. Z analizy mikrostruktury wynika, że występują odmienne procesy odbudowy struktury dla stopów Fe-28Al-5Cr oraz Fe- 38Al. Dla stopu Fe-28Al-5Cr dominującym procesem odbudowy struktury jest zdrowienie dynamiczne, a dla stopu o wyższej zawartości aluminium Fe-38Al dominuje rekrystalizacja dynamiczna. Otrzymane wyniki badań plastyczności, analizy ilościowej i jakościowej substruktury oraz opis zjawisk zachodzących w trakcie odkształcenia na gorąco istotnie wpłyną na uzupełnienie dotychczasowej wiedzy o stopach na osnowie faz międzymetalicznych z układu Fe-Al.
Alloys based on systematic intermetallic phases belong to a group of metallic materials which share the characteristics of metals and ceramics. On account of the highly advantageous properties, the Fe-Al intermetallic phase-based alloys, i.e. Fe3Al and FeAl, are considered particularly interesting. This article provides a discussion on the effect of plastic strain parameters on changes to the microstructure of the Fe-Al system alloys. The plastic strain was achieved in a test of axial-symmetric compression using the Gleeble 3800 simulator at temperatures ranging from 600oC to 1200oC with the strain rate of 0.1; 1.0 and 10.0 s-1. Based on the dependences between flow stress and strain thus established, it was possible to determine the maximum flow stress as well as the value of strain corresponding to this stress for different temperatures and strain rates. In order to calculate the Zener-Hollomon parameter Z which is deformation speed corrected due to temperature there was activation energy Q of the plastic deformation process calculated. The microstructure of the Fe-28Al-5Cr and the Fe-38Al alloy was analysed after casting and homogenising, and following the test of axial-symmetric compression using light and electron microscopy techniques. With reference to results of the microstructure analysis, it was evidenced that the Fe-28Al-5Cr and the Fe-38Al alloy displayed disparate processes of structure recovery. The predominant structure recovery process for the Fe-28Al- 5Cr alloy is known as dynamic recovery, while for the Fe-38Al alloy with a higher aluminium content, dynamic recrystallisation was proved to be dominant. The results produced by the plasticity tests, an analysis of the substructure as well as a description of the phenomena that took place during hot strain will exert significant influence on expanding the current state of knowledge about the Fe-Al intermetallic phase-based alloys.
Źródło:
Obróbka Plastyczna Metali; 2019, 30, 2; 121-134
0867-2628
Pojawia się w:
Obróbka Plastyczna Metali
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Joining of Low-Carbon Steel Sheets with Al-Based Weld
Autorzy:
Boczkal, G.
Perek-Nowak, M.
Majewska, Z.
Powiązania:
https://bibliotekanauki.pl/articles/353774.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
resistance welding
Al/Fe interface
shear test
Opis:
The analysis of the connection steel/Al/steel made by resistance welding was performed. The used low-carbon steel had low content of carbon and other elements, aluminum was of 99.997 wt.% Al purity. Formation of various FeAl intermetallic phases found in the phase diagram depending on the duration of the process was analyzed. Two distinctively different types of structure depending on time of welding were observed: 1) hypoeutectic structure for samples processed for 5 s, and 2) eutectic structure for samples processed for 10 s and more. The shear test showed increase of mechanical properties of the connection for the samples welded 10 s.
Źródło:
Archives of Metallurgy and Materials; 2016, 61, 1; 37-42
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Mössbauer and structural study of disordered alloys Fe3-xTixAl (0 < x < 1)
Autorzy:
Brząkalik, K.
Frąckowiak, J.
Powiązania:
https://bibliotekanauki.pl/articles/148880.pdf
Data publikacji:
2003
Wydawca:
Instytut Chemii i Techniki Jądrowej
Tematy:
Fe2TiAl Heusler phase
Fe-Ti-Al system
Mössbauer spectroscopy
Opis:
A series of the disordered Fe3-xTixAl (x = 0, 0.2, 0.45, 0.55, 0.65, 0.70, 0.75, 1) alloys obtained by arc-melting were studied. Directly after melting the samples were mechanically crashed and in that form examined by the structural and Mössbauer effect methods. The alloys were strongly disordered, but it was possible to identify, apart from Fe-bcc phase, the origins of forming such phases as Fe2TiAl Heusler phase, Fe3Al with DO3 structure, FeAl and FeTi with B2 structure and non-stechiometric Fe2Ti Laves phase with hexagonal C14 structure. For Ti concentration up to x = 0.45, the disordered Fe-bcc phase dominates. For Ti concentration from x = 0.55 to x = 1, the Fe2TiAl phase coexists with FeAl phase (for x = 0.55, 0.65) and with FeTi phase (x = 0.7 and 0.75). In a sample with the nominal Fe2TiAl composition of Fe2TiAl Heusler phase, a non-stoichiometric Fe2Ti Laves phase with hexagonal C14 structure was observed.
Źródło:
Nukleonika; 2003, 48,suppl.1; 13-16
0029-5922
1508-5791
Pojawia się w:
Nukleonika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The adsorption mechanism of Al(III) and Fe(III) ions on bastnaesite surfaces
Autorzy:
Cao, Shiming
Cao, Yijun
Ma, Zilong
Liao, Yinfei
Powiązania:
https://bibliotekanauki.pl/articles/110208.pdf
Data publikacji:
2019
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
Al(III)
Fe(III)
bastnaesite
adsorption
Opis:
The adsorption mechanism of Al(III) and Fe(III) ions on bastnaesite surfaces was investigated by a combination of DFT calculation, XPS analysis, adsorption isotherm study and adsorption kinetic investigations. DFT calculation results indicated that ≡CeOH0 and ≡CO3H0 are primary functional groups on bastnaesite surfaces. XPS analysis reveals that Al(III) and Fe(III) ions adsorbed onto the bastnaesite surfaces through the interaction between aluminium/iron hydroxide species and oxygen atoms of surface ≡CeOH0 groups. No interaction between aluminium/iron hydroxide species and ≡CO3H0 groups was detected. Adsorption isotherm studies demonstrated that the adsorption data of Al(III) and Fe(III) ions is fitted relatively well by Freundlich equations, the adsorption kinetic characteristics fitted to pseudo-second order model. Freundlich constants suggested favorable process for Al(III) and Fe(III) ions adsorption, and each adsorbed metal hydroxide specie complex with at least two oxygen atoms of surface ≡CeOH0 groups.
Źródło:
Physicochemical Problems of Mineral Processing; 2019, 55, 1; 97-107
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Functional and Fractal Properties of Fe-Al Coatings After Gas Detonation Spraying (GDS)
Autorzy:
Chrostek, T.
Rychlik, K.
Bramowicz, M.
Senderowski, C.
Powiązania:
https://bibliotekanauki.pl/articles/355023.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Fe-Al
intermetallic alloys
GDS
SEM
fractal analysis
Opis:
The paper presents the results and provides an analyse of the geometric structure of Fe-Al protective coatings, gas-treated under specified GDS conditions. The analysis of the surface topography was conducted on the basis of the results obtained from the SEM data. Topographic images were converted to three-dimensional maps, scaling the registered amplitude coordinates of specific gray levels to the relative range of 0÷1. This allowed us to assess the degree of surface development by determining the fractal dimension. At the same time, the generated three-dimensional spectra of the autocorrelation function enabled the researchers to determine the autocorrelation length (Sal) and the degree of anisotropy (Str) of the surfaces, in accordance with ISO 25178. Furthermore, the reconstructed three-dimensional images of the topography allowed us to evaluate the functional properties of the studied surfaces based on the Abbott-Firestone curve (A-F), also known as the bearing area curve. The ordinate describing the height of the profile was replaced by the percentage of surface amplitude in this method, so in effect the shares of the height of the three-dimensional topographic map profiles of various load-bearing properties were determined. In this way, both the relative height of peaks, core and recesses as well as their percentages were subsequently established.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 4; 1993-1999
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of gas detonation spraying parameters on the geometrical structure of Fe-Al intermetallic protective coatings
Autorzy:
Chrostek, Tomasz
Bramowicz, Mirosław
Rychlik, Kazimierz
Wojtkowiak, Adam
Senderowski, Cezary
Powiązania:
https://bibliotekanauki.pl/articles/298459.pdf
Data publikacji:
2019
Wydawca:
Uniwersytet Warmińsko-Mazurski w Olsztynie
Tematy:
GDS
Detonation Gas Spraying
Fe-Al
intermetallic alloys
fractal analysis
RMS
Opis:
The paper presents the results of an analysis of the geometrical structure of Fe-Al intermetallic protective coatings sprayed under specified gun detonation spraying (GDS) conditions. Two barrel lengths, two powder injection positions (PIP) at the moment of spark detonation, and two numbers of GDS shots with 6.66 Hz frequency were applied as variable parameters in the GDS process. Surface profile measurements were conducted by contact profilometry with the use of the TOPO-01 system and the Mitutoyo SJ 210 profilometer. The measured parameters were used to analyze surface topography in two-dimensional (2D) and three-dimensional (3D) systems. It was assumed that roughness can be regarded as a non-stationary parameter of variance in surface amplitude which is highly dependent on the sampling rate and spraying distance. Therefore, changes in surface amplitude parameters and functional properties were analyzed across segments with a length (ln) of 1.25, 4 and 12.5 mm. The development of the geometric structure of the surface was analyzed with the RMS (Root Mean Square) fractal method, and the geometric structure of the surface stretched by several orders of magnitude was evaluated based on the correlation between roughness (Rq), segment length (ln) and fractal dimension (D). The RMS method and the calculated fractal dimension (D) supported the characterization of the geometric structure of intermetallic Fe-Al protective coatings subjected to GDS under the specified process conditions based on the roughness profiles of surface segments with a different length (ln).
Źródło:
Technical Sciences / University of Warmia and Mazury in Olsztyn; 2019, 22(3); 249-262
1505-4675
2083-4527
Pojawia się w:
Technical Sciences / University of Warmia and Mazury in Olsztyn
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Tribological wear of Fe-Al coatings applied by gas detonation spraying
Autorzy:
Chrostek, Tomasz
Powiązania:
https://bibliotekanauki.pl/articles/2069744.pdf
Data publikacji:
2021
Wydawca:
Uniwersytet Warmińsko-Mazurski w Olsztynie
Tematy:
gas detonation spraying
GDS
coating
Fe-Al
intermetallic alloys
tribology
Opis:
Comparative tests of gas detonation (GDS) coatings were carried out in order to investigate the influence of spraying parameters on abrasive wear under dry friction conditions. The tests were carried out using the pin-on-disc (PoD) method at room temperature. The microstructure of the coatings was analysed by X-ray diffraction (XRD) and scanning electron microscopy (SEM/EDS) methods. The results showed that with certain parameters of the GDS process, the main phase of the produced coatings is the FeAl phase with the participation of thin oxide layers, mainly Al2O3. The tribological tests proved that the coatings sprayed with the shorter barrel of the GDS gun showed higher wear resistance. The coefficient of friction was slightly lower in the case of coatings sprayed with the longer barrel of the GDS gun. During dry friction, oxide layers form on the surface, which act as a solid lubricant. The load applied to the samples during the tests causes shear stresses, thus increasing the wear of the coatings. During friction, the surface of the coatings is subjected to alternating tensile and compressive stresses, which lead to delamination and is the main wear mechanism of the coatings.
Źródło:
Technical Sciences / University of Warmia and Mazury in Olsztyn; 2021, 24(1); 245--256
1505-4675
2083-4527
Pojawia się w:
Technical Sciences / University of Warmia and Mazury in Olsztyn
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental Investigation Of Modified Heat Treatment Of AK64-Type Al-Si-Cu Sand Cast Alloy
Eksperymentalne badania zmodyfikowanej obróbki cieplnej odlewu piaskowego ze stopu Al-Si-Cu typu AK64
Autorzy:
Cupido, L. H.
Żak, P. L.
Mahomed, N.
Lelito, J.
Piwowarski, G.
Krajewski, P. K.
Powiązania:
https://bibliotekanauki.pl/articles/355727.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminium Al-Si-Cu cast alloy
T6 heat treatment
nucleation temperature
Al2Cu and Al-Fe-Si phases
aluminium Al-Si-Cu odlewane ze stopu
obróbka cieplna T6
temperatura zarodkowania
fazy Al2Cu i Al-Fe-Si
Opis:
An experimental investigation was conducted to observe and analyze the microstructural evolution of phases present in the AK64 Al-Si-Cu alloy subjected to a modified T6 heat treatment (HT). The AK64 alloy1 is the Polish alternative of the A319.0 ASM standard aluminium alloy. The modified T6 HT schedule with a higher temperature and shorter duration was applied in the solutioning process and lower quenching and higher artificial ageing temperature than the prescribed by the ASM standard were used. The cooling curves registered during the liberating of overheating and solidifying processes give important information on nucleation temperatures for the Al dendrite network, Al-Si eutectic reaction and precipitation of Cu-rich phases. Comparison of the as-cast and heat treated microstructures revealed predicted microstructural changes and also partial fragmentation of the Fe-rich phases was observed after the application of the modified HT programme.
Artykuł poświęcony jest obróbce cieplnej stopu AK64, który jest odpowiednikiem stopu ASM: A319.0. W badaniach zastosowano zmodyfikowaną obróbkę cieplną T6 o podwyższonej (w stosunku do procedury T6 HT – ASM) temperaturze wyżarzania i skróconym czasie starzenia naturalnego po przesyceniu w wodzie. Obserwacje struktury stopu po obróbce cieplnej wykazały dużą zgodność ze strukturami przewidzianymi na podstawie przeprowadzonych symulacji numerycznych. Dodatkowo określono wartości temperatury odpowiadającej początkowi zarodkowania fazy α(Al), reakcji eutektycznej Al-Si oraz wydzielania z roztworu fazy bogatej w Cu. Opisano również częściową fragmentację fazy zawierającej Fe, będącą następstwem zastosowanej zmodyfikowanej obróbki cieplnej.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 3; 2397-2402
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies