Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "ścinanie" wg kryterium: Temat


Tytuł:
Effect of nanosilica stabilisation on the bearing capacity under undrained conditions
Wpływ stabilizacji nanokrzemionką na nośność podłoża gruntowego w warunkach bez odpływu
Autorzy:
Tankiewicz, Matylda
Mońka, Jakub
Zięba, Zofia
Powiązania:
https://bibliotekanauki.pl/articles/27312167.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czasopisma i Monografie PAN
Tematy:
nanokrzemionka
wytrzymałość na ścinanie bez odpływu
ściskanie jednoosiowe
nośność podłoża
ława fundamentowa
nanosilica
undrained shear strength
unconfined compression
bearing capacity
strip footing
Opis:
Due to the increasing necessity of building on soils with insufficient bearing capacity, the development of methods for soil improvement is an important geotechnical engineering issue. One of the innovative methods of soil stabilisation is the use of nano-additives. The paper presents the influence of nanosilica on the bearing capacity under the footing under undrained conditions. For this purpose, a simple and quick unconfined compression test was used to evaluate the undrained shear strength of selected silty soil. Tests were conducted for soil without additives and with nanosilica contents of 1, 3 and 5%. All samples were compacted to the maximum dry density in a Proctor apparatus, and strength tests were conducted after 7 days of curing. The results clearly show an increase in undrained shear strength with increasing nanosilica content. Based on these data, a parametric analysis of the bearing capacity under the strip footing was performed for 4 variants of nanosilica content and for 9 loading cases. Thus, the impact of stabilisation in a practical engineering issue was presented. For all load cases the optimal dimensions of the foundation were determined. In addition, for the selected case, calculations were made for a fixed foundation dimension. All computations were performed in accordance with Eurocode 7 with GEO5 software.
Ze względu na coraz powszechniejszą konieczność posadawienia obiektów na gruntach o niewystarczającej nośności, rozwój metod ulepszania i stabilizacji podłoża gruntowego jest aktualnym wyzwaniem inżynierii geotechnicznej. Jedną z innowacyjnych metod stabilizacji gruntu jest wykorzystanie nanododatków jako materiału stabilizującego. Zaletami tego rozwiązania są mniejsza ilość dodatku wymagana do uzyskania określonej poprawy właściwości mechanicznych gruntu względem tradycyjnych metod oraz mniejszy negatywny wpływ na środowisko. W kontekście ulepszenia podłoża gruntowego nanododatkami wybór nanokrzemionki (nano SiO2) stanowi optymalne rozwiązanie z punktu widzenia skuteczności i kosztów. W pracy przedstawiono wpływ zawartości nanokrzemionki na nośność podłoża pod ławą fundamentową w warunkach bez odpływu. W praktyce warunki te występują przede wszystkim w sytuacjach przejściowych, gdy następuje szybki przyrost obciążeń. W pierwszej kolejności wykonano badania laboratoryjne mające na celu określenie parametrów wytrzymałości wybranego gruntu bez dodatku oraz stabilizowanego nanokrzemionką. W tym celu wykorzystano prosty i szybki test jednoosiowego ściskania pozwalający na ocenę wytrzymałości gruntu w warunkach bez odpływu. Badania laboratoryjne wykonano dla wybranego gruntu pylastego. Testy przeprowadzono dla czystego materiału gruntowego oraz z dodatkiem nanokrzemionki 1, 3 i 5%. Wszystkie próbki zostały zagęszczone do maksymalnej gęstości objętościowej szkieletu gruntowego w aparacie Proctora a testy wytrzymałościowe przeprowadzono po 7 dniach dojrzewania próbek. Badania wykazały średni wzrost wytrzymałości na ścinanie bez odpływu Cu odpowiednio o 18.1%, 54.9% i 76.0% w porównaniu do gruntu bez dodatku. Zaobserwowano również znaczny wzrost modułu siecznego Eu50 tj. odpowiednio 29.7%, 111.0% i 120.1%. W przypadku wytrzymałości stwierdzono liniową zależność wytrzymałości od zawartości nanokrzemionki. Dla sztywności ta zależność była inna, jednak ze względu na duży rozrzut wyników nie można było sformułować jednoznacznych wniosków. Otrzymane dane znacznie odbiegają od tych prezentowanych w literaturze dla podobnych typów gruntów i zawartości nanokrzemionki, co prawdopodobnie spowodowane jest innymi czynnikami wpływającymi na wyniki badań.
Źródło:
Archives of Civil Engineering; 2023, 69, 3; 269--284
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characterisation of spoil materials to develop an equivalent spoil material for physical model tests
Charakterystyka odpadów pogórniczych w celu opracowania materiału równoważnego do modelowania fizycznego
Autorzy:
Garala, Thejesh Kumar
Cui, Ge
Kantesaria, Naman
Heron, Charles M.
Marshall, Alec M.
Žižka, Lukáš
Powiązania:
https://bibliotekanauki.pl/articles/2175665.pdf
Data publikacji:
2022
Wydawca:
Poltegor-Instytut Instytut Górnictwa Odkrywkowego
Tematy:
cone penetration testing
laboratory testing
shear strength
soil-water characteristic curve
spoil
sondowanie CPT
badania laboratoryjne
wytrzymałość na ścinanie
krzywa retencji wodnej gruntu
zwałowisko
Opis:
The engineering behaviour of spoil (overburden) needs to be explored either to understand the stability of reservoir slopes under various geological and climatic conditions or for the effective utilisation of reclaimed mines for sustainable infrastructure (e.g., onshore wind turbines). The spoil material is usually considered as highly heterogeneous, and samples collected from the same site can exhibit widely varying characteristics. In this study, spoil material from a mine site in the Czech Republic is characterised using in-situ field tests and laboratory tests. Cone penetration tests were performed in the field and sample cores were collected for laboratory testing. In the laboratory, the index and engineering characteristics of the spoil were evaluated. Given the measured characteristics and behaviour of the field spoil, an equivalent spoil is proposed to perform physical modelling tests using geotechnical centrifuge. This enables simulation of the field spoil behaviour in controlled centrifuge testing, from which other aspects of spoil (e.g. stability of spoil slopes, spoil-structure interaction) can be investigated.
Zachowanie zwałowisk pogórniczych (nadkładu) pod względem inżynieryjnym powinno zostać zbadane w celu określenia stabilności zboczy zbiorników poeksploatacyjnych w różnych warunkach geologicznych i klimatycznych lub w celu efektywnego wykorzystania rekultywowanych kopalń do budowy zrównoważonej infrastruktury (np. lądowych turbin wiatrowych). Materiał zwałowisk pogórniczych jest zwykle uważany za wysoce niejednorodny, a próbki pobrane z tego samego miejsca mogą wykazywać bardzo różne właściwości. W niniejszej pracy, materiał odpadowy z czeskiej kopalni został scharakteryzowany przy użyciu badań terenowych i laboratoryjnych in-situ. W terenie przeprowadzono sondowania CPT, a do badań laboratoryjnych pobrano próbki rdzeniowe. W laboratorium oceniono właściwości indeksowe i inżynieryjne materiału. Biorąc pod uwagę zmierzone cechy i zachowanie się materiału pogórniczego, zaproponowano materiał równoważny do wykonania modelowania fizycznego z wykorzystaniem wirówki geotechnicznej. Umożliwia to symulację zachowania się materiału w kontrolowanych badaniach wirówkowych, na podstawie których można badać inne cechy materiałów pogórniczych (np. stabilność skarp zwałowiska, interakcje zwałowisko-konstrukcja budowlana).
Źródło:
Górnictwo Odkrywkowe; 2022, 63, 4; 23--29
0043-2075
Pojawia się w:
Górnictwo Odkrywkowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of overlap length on the strength of adhesive joints of steel sheets
Wpływ długości zakładki na wytrzymałość połączeń klejowych blach stalowych
Autorzy:
Doluk, Elżbieta
Rudawska, Anna
Miturska-Barańska, Izabela
Ogrodniczek, Jacek
Powiązania:
https://bibliotekanauki.pl/articles/31232904.pdf
Data publikacji:
2022
Wydawca:
Politechnika Rzeszowska im. Ignacego Łukasiewicza. Oficyna Wydawnicza
Tematy:
adhesive joint
shear strength
elongation
overlap length
połączenie klejowe
wytrzymałość na ścinanie
wydłużenie
długość zakładki
Opis:
The study evaluates the shear strength of the single-lap adhesive joints made of C45 carbon steel. The influence of the overlap length on the shear strength of the adhesive joint was tested. The elongation of the samples was also tested. Before the bonding process, the samples were treated with P180 abrasive paper and degreased. The adhesive joints were made using the Epidian 53/Z1/100:10 adhesive composition. The strength tests were carried out on a Zwick/Roell Z150 testing machine. The maximum value of the shear strength was obtained for the lap Lz1 = 13 mm and the minimum for Lz4 = 19 mm.
W pracy dokonano oceny wpływu długości zakładki na wytrzymałość na ścinanie jednozakładkowych połączeń klejonych wykonanych ze stali węglowej C45. Podczas eksperymentu zbadano także wydłużenie próbek. Przed rozpoczęciem procesu klejenia próbki zostały obrobione papierem ściernym P180 i odtłuszczone. Połączenia klejowe wykonano przy użyciu kompozycji klejowej Epidian 53/Z1/100:10. Badania wytrzymałościowe przeprowadzono na maszynie wytrzymałościowej Zwick/Roell Z150. Maksymalną wartość wytrzymałości na ścinanie uzyskano dla długości zakładki Lz1 = 13 mm, a minimalną dla Lz4 = 19 mm.
Źródło:
Technologia i Automatyzacja Montażu; 2022, 4; 3-6
2450-8217
Pojawia się w:
Technologia i Automatyzacja Montażu
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of hydrocarbon contamination on the engineering geological properties of Neogene clays and Pleistocene glacial tills from Central Poland
Autorzy:
Dobak, Paweł
Izdebska-Mucha, Dorota
Stajszczak, Piotr
Wójcik, Emilia
Kiełbasiński, Kamil
Gawriuczenkow, Ireneusz
Szczepański, Tomasz
Zawrzykraj, Piotr
Bąkowska, Anna
Powiązania:
https://bibliotekanauki.pl/articles/24024696.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czasopisma i Monografie PAN
Tematy:
petroleum products
contamination
clay soils
permeability
shear strength
swelling
particle size distribution
produkty naftowe
zanieczyszczenia
grunty spoiste
przepuszczalność
wytrzymałość na ścinanie
pęcznienie
rozkład wielkości cząstek
PSD
Opis:
Petroleum products influence the engineering behaviour of the soil. Neogene clays and glacial tills from Central Poland were tested under laboratory conditions to evaluate the changes of selected physical and mechanical parameters: particle size distribution, particle density, swelling, shear strength and permeability. Four petroleum products were used in the experiments: diesel fuel, kerosene, jet fuel and mineral engine oil. The study revealed that even for the lowest degree of contamination the values of physical and mechanical properties of the soils changed significantly. Greater variation can be expected in soils contaminated with high-viscosity compounds. Also, higher relative changes were found for glacial tills than for Neogene clays. Consolidation tests revealed changes in soil permeability depending on the soil composition and the physical properties of the contaminant – considerable reduction of permeability was observed for glacial tills contaminated with light Jet fuel, while the reduction was lower for Neogene clays. The obtained results indicate the role of mesopores and the dimensionless pore pressure coefficient in changes of soil permeability. The methodological issues regarding testing and analysing the hydrocarbon-contaminated soils were also presented and discussed, which might be useful for researchers studying contaminated soils.
Źródło:
Acta Geologica Polonica; 2022, 72, 4; 529--555
0001-5709
Pojawia się w:
Acta Geologica Polonica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Improvement of the graphical method for plotting the shear and moment diagrams for members subjected to linearly varying loads
Autorzy:
Husain, Muhammed Abbas
Ali, Abdulkhaliq Salim
Powiązania:
https://bibliotekanauki.pl/articles/2174180.pdf
Data publikacji:
2022
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
ścinanie
ścinanie belki
mechanika materiałów
shear diagrams
moment diagram
graphical method
improvement
varying load
Opis:
This study presents an improvement of the graphical method for plotting the shear and moment diagrams for the structural members under linearly varying loads (triangular and trapezoidal loads). Based on the parabolic nature of the shear function, when the loading varies linearly, and on the relations among load, shear, and moment, a mathematical equation is developed to locate the zero-shear point, while a geometric technique is presented to calculate the parabolic shear area. Five comprehensive examples of beams loaded with linearly varying loads are selected to illustrate the steps of the solution for the proposed techniques. The results demonstrated the applicability of the presented method, and gave exact diagrams compared with the basic graphical method. It is concluded that the proposed improved method is generally more convenient, less time-consuming, and has less computational efforts because it does not require sectioning, solving equilibrium equations, and quadratic formulas compared with the basic graphical method.
Źródło:
International Journal of Applied Mechanics and Engineering; 2022, 27, 1; 46--66
1734-4492
2353-9003
Pojawia się w:
International Journal of Applied Mechanics and Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Moisture influence on solid wood bonded with modified starch
Autorzy:
Bartoszuk, Katarzyna
Kowaluk, Grzegorz
Powiązania:
https://bibliotekanauki.pl/articles/2171754.pdf
Data publikacji:
2022
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
starch
glue
birch wood
Betula pendula Roth
bonding
shear strength
skrobia
klej
brzoza
klejenie
wytrzymałość na ścinanie
Opis:
Moisture influence on solid wood bonded with modified starch. A growing and developing population is contributing to the ever-increasing global warming, which is caused, among other things, by the heavy use of chemicals. Most of them are crude oil-based, which is a non-renewable source. That is why the population tries to find organic substitutes in every area, even in the wood industry. Here, the most common and popular binders - amine resins, are subjected in research to partial or full replacement by more natural binders, non-formaldehyde, made of renewable raw materials, preferably plant-based. In this project, the studies were carried out on the possibility of starch-based glue application in wood bonding and its effect on glued birch wood (Betula pendula Roth) under various environmental storage conditions of bonded samples (0%, 65%, and 100% of RH). The results show, that the samples at room temperature and normal humidity, as well as another – additionally dried, have a very similar shear strength. In-wood damages, on the other hand, are much more varied. The research also included moistened samples, which gave poorer results (about 12% lower than the remaining samples). Based on the results, it can be concluded, that modified starch is a very good organic glue, that can potentially replace some chemical products in certain applications.
Wpływ wilgoci na drewno lite sklejone skrobią modyfikowaną. Przeprowadzono badania nad możliwością zastosowania kleju skrobiowego w spajaniu drewna i jego wpływem na klejone drewno brzozowe (Betula pendula Roth) w różnych warunkach środowiskowych przechowywania sklejonych próbek. Wyniki pokazują, że próbki w temperaturze pokojowej i normalnej wilgotności, a także inne – dodatkowo wysuszone, mają bardzo zbliżoną wytrzymałość na ścinanie. Z drugiej strony uszkodzenia drewna są znacznie bardziej zróżnicowane. Badaniami objęto również próbki nawilżane, co dało gorsze wyniki. Na podstawie uzyskanych wyników można stwierdzić, że skrobia modyfikowana jest bardzo dobrym klejem organicznym, który potencjalnie może zastąpić niektóre produkty chemiczne w szczególnych zastosowaniach.
Źródło:
Annals of Warsaw University of Life Sciences - SGGW. Forestry and Wood Technology; 2022, 118; 67--73
1898-5912
Pojawia się w:
Annals of Warsaw University of Life Sciences - SGGW. Forestry and Wood Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Porównanie wyników badania sondą krzyżakową i penetrometrem tłoczkowym jako przykład lokalnych zależności korelacyjnych
Comparison of the results of field vane tests and pocket penetrometer tests as an example of local correlations
Autorzy:
Bardel, Tomasz
Powiązania:
https://bibliotekanauki.pl/articles/29521111.pdf
Data publikacji:
2022
Wydawca:
Akademia Tarnowska
Tematy:
parametry geotechniczne gruntów
wytrzymałość na ścinanie bez odpływu
stopień plastyczności
gliny zwałowe
mady gliniaste
Tarnów
geotechnical parameters of the soil
degree of plasticity
boulder clay
clayey alluvium
Opis:
Badania polowe i laboratoryjne gruntów dostarczają dużą ilość danych, jednak większość z nich stanowią parametry pomierzone, które z wykorzystaniem różnych wzorów i korelacji przelicza się na parametry wykorzystywane do projektowania. Stosowanie ogólnych korelacji do ich przeliczania nie zawsze prowadzi do uzyskania kompatybilnych wartości, dlatego pożądane jest poszukiwanie lokalnych zależności korelacyjnych. W niniejszym artykule przedstawiono zależność korelacyjną pomiędzy wytrzymałością na ścinanie bez odpływu uzyskiwaną z sondy krzyżakowej FVT i penetrometru tłoczkowego dla glin zwałowych rejonu Tarnowa. Na podstawie tej korelacji opracowano krzywą zależności oporu wcisku penetrometru tłoczkowego i stopnia plastyczności. Korelację tę wykorzystano następnie przy badaniu mad gliniastych doliny Dunajca, uzyskując wysokie wartości współczynnika korelacji. Otrzymane wyniki potwierdzają przydatność penetrometru tłoczkowego jako metody szybkiego określania wytrzymałości na ścinanie bez odpływu oraz stopnia plastyczności.
Field and laboratory tests of soils provide a large amount of data, but most of them are measured parameters, which are converted by various formulas and correlations into parameters used for design. General correlations does not always lead to obtaining compatible values, therefore it is desirable to search for local correlations. This article presents the correlation between the undrained shear strength from the field vane tests (FVT) and the pocket penetrometer for tills in the Tarnów region. On the basis of this correlation, a dependence curve of the unconfined compressive strength measured by pocket penetrometer and the liquidity index was developed. This correlation was then used of river’s clay muds in the Dunajec valley. The high values of the correlation coefficient were obtained. The results confirm the usefulness of the pocket penetrometer as a method of quick determination of the undrained shear strength and liquidity index.
Źródło:
Science, Technology and Innovation; 2022, 16, 3-4; 20-27
2544-9125
Pojawia się w:
Science, Technology and Innovation
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Rheological properties of paste for self-compacting concrete with admixtures
Autorzy:
Liu, He
Duan, Guangchao
Zhang, Jingyi
Yang, Yanhai
Powiązania:
https://bibliotekanauki.pl/articles/2174035.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
beton samozagęszczalny
właściwości reologiczne
zagęszczenie
ścinanie
krytyczne naprężenie ścinające
lepkość minimalna
domieszka
self-compacting concrete
rheologic properties
shear thickening
critical shear stress
minimum viscosity
admixture
Opis:
The paste content in the self-compacting concrete is about 40% in unit volume. The rheological properties of paste directly determine the properties of self-compacting concrete. In this paper, the effect of silica fume (2, 3, 4, and 5%), limestone powder (5, 10 and 15%), and the viscosity modified admixture (2, 3, 4, 5, 6, and 7%) on the rheological properties were investigated. The effect of admixtures on shear thickening response was discussed based on the modified Bingham model. The results indicate that yield stress and plastic viscosity increased with increased silica fume and viscosity modified admixture replacement. The paste’s yield stress increases and then decreases with limestone powder replacement. The critical shear stress and minimum plastic viscosity are improved by silica fume and viscosity modifying admixture. The critical shear stress first increases and decreases as the limestone powder replacement increases. A reduction in the shear thickening response of paste was observed with silica fume and viscosity modified admixture replacement increase.
Źródło:
Archives of Civil Engineering; 2022, 68, 3; 585--599
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of the manufacturing method on the mechanical properties of the honeycomb core sandwich composite
Wpływ metody wytwarzania na właściwości mechaniczne kompozytu przekładkowego z wypełniaczem ulowym
Autorzy:
Janiszewski, Jacek
Przybyłek, Paweł
Bieńczak, Rafał
Komorek, Łukasz
Schwarzenberg, Miłosz
Powiązania:
https://bibliotekanauki.pl/articles/31232914.pdf
Data publikacji:
2022
Wydawca:
Politechnika Rzeszowska im. Ignacego Łukasiewicza. Oficyna Wydawnicza
Tematy:
sandwich composites
composite manufacturing processes
vacuum bagging technique
impact strength
shear strength
kompozyty przekładkowe
metoda wytwarzania kompozytu
technika worka próżniowego
udarność
wytrzymałość na ścinanie
Opis:
Reducing weight and fuel consumption is one of the main goals of modern aeronautical engineering. The most common materials to achieve this goal are composite layered materials, including the sandwich ones. High strength, stiffness and low density have made sandwich composites one of the fundamental materials of the aerospace industry. Sandwich-structured composites can be manufactured with a variety of methods, differing primarily in the manufacturing time, which translates into an overall cost of making a composite component. The research focused on three methods of manufacturing sandwich composite materials with a honeycomb core, differing in the number of operations, during which it was possible to obtain a finished composite panel (single-phase, two-phase and three-phase methods). The authors manufactured and examined composites with a honeycomb cover and two composite glass fibre-reinforced covers. The composites were made by means of the vacuum bag method. As a result of the conducted study, it was found that composites manufactured with the single-phase method have the shortest manufacture time as well as the lowest material consumption, however their strength properties are the lowest. The two-phase method requires a longer manufacture time and more material consumption, however it makes it possible to obtain a composite with higher strength compared with the single-phase method. The three-phase method has the longest composite manufacture time and the highest material consumption.
Zmniejszenie masy i zużycia paliwa jest jednym z głównych celów współczesnej inżynierii lotniczej. Najpopularniejsze materiały, które pozwalają osiągnąć ten cel, to materiały kompozytowe warstwowe w tym przekładkowe. Wysoka wytrzymałość, sztywność i niska gęstość, sprawiły, że kompozyty przekładkowe stały się jednym z podstawowych materiałów przemysłu lotniczego. Kompozyty przekładkowe z wypełniaczem strukturalnym mogą być wytwarzane różnymi metodami, różniącymi się przede wszystkim czasem wytwarzania, co przekłada się na ogólny koszt wykonania elementu kompozytowego. W badaniach przeanalizowano trzy metody wytwarzania materiałów kompozytowych przekładkowych w wypełniaczem ulowym różniące się liczbą operacji podczas których uzyskano gotową płytę kompozytową (metoda jednofazowa, dwufazowa i trójfazowa). Wytworzono i badano kompozyty zbudowane z rdzenia ulowego oraz dwóch kompozytowych okładek wzmacnianych włóknami szklanymi. Kompozyty wykonano metodą worka próżniowego. W efekcie przeprowadzonych badań stwierdzono, że kompozyty wytworzone metodą jednofazową cechują się najkrótszym czasem produkcji jak i najmniejszym zużyciem materiałów, ale ich właściwości wytrzymałościowe są najniższe. Dwufazowa metoda wymaga dłuższego czasu produkcji i większego zużycia materiałów, natomiast pozwala uzyskać kompozyt o większej wytrzymałości w porównaniu do metody jednofazowej. Trójfazowa metoda cechuje się najdłuższym czasem wykonania kompozytu i największym zużyciem materiałów.
Źródło:
Technologia i Automatyzacja Montażu; 2022, 4; 20-33
2450-8217
Pojawia się w:
Technologia i Automatyzacja Montażu
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Anisotropy of soil shear strength parameters caused by the principal stress rotation
Anizotropia parametrów wytrzymałościowych w gruntach spowodowana obrotem kierunków naprężeń głównych
Autorzy:
Wrzesiński, Grzegorz
Powiązania:
https://bibliotekanauki.pl/articles/1853642.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
grunt
wytrzymałość na ścinanie bez odpływu
spójność
kąt tarcia wewnętrznego
obrót kierunków naprężeń głównych
badanie geotechniczne
aparat cylindryczny skrętny
aparat trójosiowy
soil
undrained shear strength
cohesion
internal friction angle
principal stress rotation
torsional shear
hollow cylinder test
triaxial test
Opis:
The paper presents the phenomenon of principal stress rotation in cohesive subsoil resulting from its loading or unloading and the impact of this phenomenon on the values of soil shear strength parameters: undrained shear strength τfu, effective cohesion c’, effective angle of internal friction φ’. For this purpose, tests in a triaxial apparatus and torsional shear hollow cylinder apparatus on selected undisturbed cohesive soils: sasiCl, saclSi, clSi, Cl, characterized by different index properties were carried out. Soil shear strength parameters were determined at angle of principal stress rotation α equal to 0° and 90° in tests in triaxial apparatus and α equal to 0°, 15°, 30°, 45°, 60°, 75°, 90° in tests in torsional shear hollow cylinder apparatus. The results of laboratory tests allow to assess the influence of the principal stress rotation on the shear strength parameters that should be used to determine the bearing capacity of the subsoil.
W artykule przedstawiono wpływ obrotu kierunków naprężeń głównych na wartości parametrów wytrzymałościowych gruntów spoistych: wytrzymałość na ścinanie bez odpływu τfu, efektywną spójność c', efektywny kąt tarcia wewnętrznego φ’. W tym celu przeprowadzono badania w aparacie trójosiowym i w cylindrycznym aparacie skrętnym na wybranych gruntach spoistych o nienaruszonej strukturze: sasiCl, saclSi, clSi, Cl o różnych wartościach parametrów fizycznych. Badano grunty o współczynniku prekonsolidacji OCR w zakresie od 1.1 do 5.7, wskaźniku plastyczności Ip w zakresie od 10.0% do 83.8% oraz wskaźniku konsystencji Ic w zakresie od 0.14 do 1.16. Parametry wytrzymałościowe gruntów określono przy kątach obrotu kierunków naprężeń głównych α równych 0° i 90° w badaniach w aparacie trójosiowym i kątach α równych 0°, 15°, 30°, 45°, 60°, 75°, 90° w badaniach w cylindrycznym aparacie skrętnym. Wyniki badań laboratoryjnych pozwoliły ocenić wpływ obrotu kierunków naprężeń głównych na parametry wytrzymałościowe gruntów spoistych niezbędnych przy wyznaczaniu nośności podłoża.
Źródło:
Archives of Civil Engineering; 2021, 67, 1; 163-187
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Assessment and verification of correlations in CPTu testing on the example of soil from the Wroclaw surroundings (Poland)
Autorzy:
Tankiewicz, Matylda
Bagińska, Irena
Powiązania:
https://bibliotekanauki.pl/articles/1853867.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
wskaźnik ściśliwości
wytrzymałość na ścinanie
ściskanie jednoosiowe
cone penetration test
in situ testing
undrained shear strength
uniaxial compression
compression index
oedometer test
Opis:
The paper presents the results of a series of Cone Penetration Test CPTu performed near the city of Wroclaw (Poland). The tests were carried out in 13 testing points located in close distance to each other. To verify the results of the penetration tests, fine-grained soil samples from selected depths were taken for laboratory tests. The study focuses on the evaluation of soil type, unit weight, and undrained shear strength cu, and compression index Cc. The grain size distribution of the soil and its mechanical parameters on the basis of a uniaxial compression and an oedometer tests were estimated. A comparison of laboratory and CPTu for selected values is presented. Determination of soil type was carried out on the basis of ISBT and IC values and good agreement with the granulometric composition was found. For undrained shear strength, commonly used correlations based on Nk, Nkt and Nke were adopted. However, the values obtained from the CPT are significantly lower than the results from laboratory tests. Therefore, values of cone factors suitable for investigated soil type and reference test were proposed. In the case of the compression index, the coefficient values βc and αm obtained agreed with those available in the literature. The findings presented in the paper indicate that laboratory tests remain necessary to identify soil properties from CPTu. The presented results are also a contribution to the knowledge of local soil conditions in the Lower Silesia area (Poland).
Źródło:
Archives of Mining Sciences; 2021, 66, 2; 313-327
0860-7001
Pojawia się w:
Archives of Mining Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of shear reinforcement ratio on the shear capacity of GFRP reinforced concrete beams
Wpływ stopnia zbrojenia poprzecznego na nośność ścinania belek zbrojonych prętami GFRP
Autorzy:
Szczech, Damian
Kotynia, Renata
Powiązania:
https://bibliotekanauki.pl/articles/1853646.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
nośność na ścinanie
pręt GFRP
belka betonowa
mechanizm zniszczenia
odkształcenie
stopień zbrojenia
zbrojenie poprzeczne
shear capacity
GFRP bar
concrete beam
failure mode
strain
shear reinforcement
reinforcement ratio
Opis:
The paper presents results of experimental tests carried out on concrete beams reinforced with glass fibre polymer reinforced (GFRP) bars, which have become recently one of the main substitutes for traditional steel reinforcement. GFRP bars were used in this research as the longitudinal and transverse reinforcement. An objective of the study was to investigate the influence of the shear reinforcement ratio on the shear capacity of GFRP reinforced concrete beams in comparison with the corresponding beam without shear reinforcement. Single-span, simply-supported T-section beams reinforced in flexure with 5 GFRP bars of 25 mm diameter were reinforced in shear with closed GFRP stirrups of 8 mm diameter applied in three variable spacings: 250 mm, 200 mm and 120 mm. The analysis of test results, failure modes and shear capacity is discussed in the paper in respect to investigated parameters.
W artykule przedstawiono wyniki badań eksperymentalnych przeprowadzonych na betonowych belkach zbrojonych prętami z włókna szklanego GFRP (Glass Fibre Reinforced Polymer), które w ostatnim czasie stały się jednym z głównych zamienników tradycyjnego zbrojenia stalowego. Celem badań była analiza wpływu stopnia zbrojenia poprzecznego na nośność na ścinanie belek żelbetowych zbrojonych GFRP w porównaniu z belką bez zbrojenia na ścinanie. Zastosowano trzypunktowy schemat obciążenia belek o smukłości ścinania (a/d) równym 3,15 co klasyfikuje belki jako smukłe, bez występowania efektu łukowego podczas ścinania. Analizie poddano jednoprzęsłowe belki o przekroju teowym (beff = 650 mm, bw = 250 mm, hf = 80 mm, htot = 400 mm) o rozpiętości w osiach podpór 1800 mm. Obciążenie skupione przyłożono w odległości 1050 mm od podpory. Zbrojenie podłużne składało się z 5 prętów GFRP o średnicy 25 mm (stopień zbrojenia poprzecznego ρl = 2,91%). Zbrojenie poprzeczne zastosowano w formie zamkniętych strzemion GFRP o średnicy 8 mm w trzech różnych rozstawach: sf = 250 mm, 200 mm and 120 mm, odpowiadające odpowiednio trzem stopniom zbrojenia poprzecznego ρs: 0,16%, 0,20% i 0,33%. W celu porównania wpływu rozstawu strzemion na nośność belek na ścinanie zbadano element referencyjny bez zbrojenia poprzecznego.
Źródło:
Archives of Civil Engineering; 2021, 67, 1; 425-437
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Finite Element Modeling of Self-Compacting Concrete Beams Under Shear
Autorzy:
Hosseinimehrab, lham
Sadeghi, Abbasali
Noroozinejad Farsangi, Ehsan
Powiązania:
https://bibliotekanauki.pl/articles/2051577.pdf
Data publikacji:
2021
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
concrete beams
self-compacting concrete
shear capacity
finite element modeling
belka betonowa
beton samozagęszczalny
ścinanie
modelowanie elementów skończonych
Opis:
Development of self-compacting concrete (SCC) is a very desirable achievement in the reinforced concrete (RC) structures for overcoming issues associated with many problems such as congestions of steel reinforcement. This non-vibrating concrete is not affected by the skill of workers, and the shape and amount of reinforcing bar arrangement of a structure. Due to the high fluidity and resisting power of reinforcing of SCC, it can be pumped longer distances. In this study, the finite element (FE) modeling of three SCC beams in shear while taking into account, the flexural tensile strength of concrete is computed and the results are compared with the available experimental tested reinforced SCC beams. The stirrups are located at 75 mm apart from the end of beams up to the loading point. The electrical strain gauges (ESGs) have been embedded on the stirrups and their strain readings are taken for every step of load increment. For modeling longitudinal steel reinforcing bars and concrete, the 3-D elements with 2-node and 8-node, are used respectively. The comparison of results obtained by two methods is indicated that a good satisfactory agreement is achieved.
Źródło:
Civil and Environmental Engineering Reports; 2021, 31, 4; 1-16
2080-5187
2450-8594
Pojawia się w:
Civil and Environmental Engineering Reports
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High flow, low shear impellers versus high shear impellers; dispersion of oil drops in water and other examples
Autorzy:
Pacek, Andrzej W.
Nienow, Alvin W.
Powiązania:
https://bibliotekanauki.pl/articles/2034043.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high shear
high flow descriptors
drop sizes
mixing time
bioprocessing
ścinanie
deskryptory wysokiego przepływu
rozmiar kropli
czas mieszania
bioprzetwarzanie
Opis:
Flow patterns generated by two ChemShear impellers, CS 2 and CS 4 have been measured and flow numbers calculated; Fl = 0.04 for both impellers. Transient and equilibrium drop sizes, d32 μm of 3 different viscosity silicone oils agitated by a high-shear Rushton turbine, RT, a low-shear, high-flow HE3 impeller and the two ChemShears were determined. The equilibrium d32 are correlated for all impellers, by d32 = 1300(εT )−0.58 max.svv0.14 with an R2 = 0.94. However, the time to reach steady state and the equilibrium size at the same specific power do not match the above descriptors of each impeller’s characteristics. In other literature, these descriptors are also misleading. In the case of mixing time, a high shear RT of the same size as a high flow HE3 requires the same time at the same specific power in vessels of H/T = 1. In bioprocessing, where concern for damage to cells is always present, free suspension animal cell culture with high shear RTs and low-shear impellers is equally effective; and with mycelial fermentations, damage to mycelia is greater with low shear than high. The problems with these descriptors have been known for some time but mixer manufacturers and ill-informed users and researchers continue to employ them.
Źródło:
Chemical and Process Engineering; 2021, 42, 2; 77-90
0208-6425
2300-1925
Pojawia się w:
Chemical and Process Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical Modeling of the Degradation of the Normal Stress Under Large Number of Shearcycles
Autorzy:
Bellayoune, Assia
Messast, Salah
Boulon, Marc
Powiązania:
https://bibliotekanauki.pl/articles/2051692.pdf
Data publikacji:
2021
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
bearing capacity of piles
normal stress
shear
friction
degradation
numerical modeling
nośność pali
naprężenie normalne
tarcie
ścinanie
degradacja
modelowanie numeryczne
Opis:
The evaluation of friction is an important element in the verification of stability and the determination of the bearing capacity of piles. In the case of cyclic stress, the soil-pile interface has a relaxation which corresponds to a fall in the horizontal stress which represents the normal stress at the lateral surface of the pile. This paper presents an explicit formulation to express the degradation of the normal stress after a large number of shear cycles as a function of cyclic parameters. In this study we are interested in the exploitation of the cyclic shear tests carried out by Pra-ai with imposed normal rigidity (CNS) in order to demonstrate the phenomenon of falling of the normal stress. The approach presented in this paper consists in proposing a simple expression for estimating the degradation of normal stress as a function of cyclic shear parameters after a large number of cycles. The validation of this approach is verified by the application of this formulation to a real case where the comparison of the simulations made by this approach with those recorded on site shows the good adaptation of this approach to this type of problems.
Źródło:
Civil and Environmental Engineering Reports; 2021, 31, 3; 118-133
2080-5187
2450-8594
Pojawia się w:
Civil and Environmental Engineering Reports
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies