Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Zamorowski, J." wg kryterium: Autor


Wyświetlanie 1-11 z 11
Tytuł:
Strength and stability of structures with nodes flexible in terms of shift
Nośność i stateczność konstrukcji z węzłami podatnymi na przesuw
Autorzy:
Zamorowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/2084029.pdf
Data publikacji:
2020
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
nodes flexibility in terms of shift
flexibility lap joints in terms of shift and rotation
modelling
of structures with nodes flexible in terms of shift
Opis:
Distribution of internal forces in bar structures in relation to rotational flexibility of their nodes is widely discussed in the literature. However, the investigations concerning such structures with nodes flexible in terms of shift are less frequent. This paper presents examples of structures, in which the shift flexibility of lap joints determined their load-bearing capacity and stability, as well as the serviceability limit states. A low-rise dome, a covering of the exhibition hall in Chorzów, which collapsed in 2006, and a mobile telephony tower were depicted. Mechanical models describing rotational stiffness and shift flexibility of various lap joints by means of component method were used. Mathematical model by Kishi and Chen was applied to model the susceptibility of lap joints under alternating loads. In case of the low-rise dome, the results indicated that the failure was determined by joint clearances. In case of covering of the exhibition hall in Chorzów, flexibility of joints resulted in excessive utilization of resistance in certain lattice purlins, which could have initiated the disaster. In turn, flexibility of connections rarely considered in the design of mobile phone towers may result in an excessive sway of the tower legs on which the antennas of the radio link are suspended and thus interfere transmitted signals. The study showed that there is a need to take into account the influence of flexible nodes, not only in the structures sensible to deformations like low-rise domes, but also in the other structures, like mobile phone towers, in which their serviceability limit state is decisive.
Źródło:
Acta Scientiarum Polonorum. Architectura; 2021, 20, 1; 51-64
1644-0633
Pojawia się w:
Acta Scientiarum Polonorum. Architectura
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Static analysis of a variable cross-section element under load
Statyka elementu ze zmiennym przekrojem pod obciążeniem
Autorzy:
Zamorowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/2084042.pdf
Data publikacji:
2021
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
incremental solution by displacement method
strengthening of structures
degradation of stiffness
Opis:
An incremental solution of a member in bending and compression by displacement method with shear force impact is presented, wherein individual incremental steps, both the geometrical characteristics of the cross- -section and the position of the neutral axis, can be changed. Functions of loads, internal forces and displacements are represented by trigonometric series. In every load step internal forces and deformation state is memorised, therefore history of the load and stiffness is taken into account. This solution is useful both in static calculations of structures being strengthened as well as in structures, in which degradation of stiffness under load occurs as a result of wall stability loss. The member may be loaded by uniformly distributed load, any number of concentrated forces and nodal moments.
Źródło:
Acta Scientiarum Polonorum. Architectura; 2021, 20, 2; 27-40
1644-0633
Pojawia się w:
Acta Scientiarum Polonorum. Architectura
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
An initially deformed flat frame finite element
Autorzy:
Zamorowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/230223.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
deformacja początkowa
rama płaska
nieliniowość geometryczna
przemieszczenie duże
obrót duży
obrót mały
metoda elementów skończonych
initial deformation
flat frame
geometrical nonlinearity
large displacements
large rotation
small rotation
finite element method
Opis:
The paper presents the author’s non-linear FEM solution of an initially stressless deformed flat frame element, in which the nodes are situated along the axis of the bar initially straight. It has been assumed that each node may sustain arbitrary displacements and rotation. The solution takes into account the effect of shear, the geometrical non-linearity with large displacements (Green-Lagrange’s strain tensor) and moderate rotations (i.e. such ones which allow a linear-elastic behaviour of the material) and alternative small rotations when the second Piola-Kirchhoff stress tensor is applied. This solution is based on [1], concerning beams without any initial bow imperfections. The convergence of the obtained results at different numbers of nodes and Gauss points in the element was tested basing on the example of circular arcs with a central angle of 120º-180º. The analysis concerned elements with two, three, five, seven, nine and eleven nodes, for the same number of points of numerical integration and also with one more or less. Moreover, the effect of distributing the load on the convergence of the results was analyzed.
Źródło:
Archives of Civil Engineering; 2013, 59, 3; 381-400
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of load capacity of roof trusses with imperfections and the issue of equivalent load adoption
Problem właściwego przyjmowania obciążenia zastępczego w dachu z imperfekcjami
Autorzy:
Gremza, G.
Zamorowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/2084028.pdf
Data publikacji:
2020
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
truss imperfections
equivalent load
2nd order analysis
limit state
Opis:
The internal forces and stresses were analyzed and utilization of the design resistance in selected members of the roof structure with local and global geometrical imperfections was evaluated. Values of these imperfections were based on the information given in the standards EN 1090-2 and EN 1993-1-1. Besides the basic reference model with imperfections, models without imperfections, with different equivalent load arrangements by the authors’ own concept and comparatively according to the standard EN 1993-1-1 were analyzed. The calculations were made using the 1st and the 2nd order analysis. Conclusion concerning accuracy of the internal forces estimation and limit states check by use the equivalent load system proposed in the standard EN 1993-1-1 are presented. Deficiencies in the provisions of this standard in terms of adopting equivalent loads in roof structures with imperfections, resulting in underestimation of the stresses in the bottom chords of the roof trusses, has been demonstrated.
Źródło:
Acta Scientiarum Polonorum. Architectura; 2021, 20, 1; 65-76
1644-0633
Pojawia się w:
Acta Scientiarum Polonorum. Architectura
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
On the Design of a Steel End-Plate Beam-to-Column Bolted Joint According to PN-EN 1993-1-8
Autorzy:
Zamorowski, J.
Gremza, G.
Powiązania:
https://bibliotekanauki.pl/articles/104835.pdf
Data publikacji:
2018
Wydawca:
Politechnika Rzeszowska im. Ignacego Łukasiewicza. Oficyna Wydawnicza
Tematy:
component method
equivalent T-stub
joint capacity
joint stiffness
Opis:
Considering joints with unstiffened columns, the load capacity of an inner bolt-row being a part of bolts group defined by a flange capacity is directly proportional to a distance between bolts. In turn, a flexibility of the column flange in the inner bolt-row area depends not only on that distance but also on a flexibility of other basic joint components. Hence, that situation may occur, when internal forces in inner bolt-row will be greater than its capacity estimated as an equivalent of T-stub. This possibility has been taken into account in the standard [3] - see the rule in the point 6.2.4.2 (3). In practice, this rule is not implemented in calculations of this kind of joints. In this work, a simplified algorithm of these joints calculation as well as an example, where the need for force reduction in the inner bolt-row to the value of bolt resistance has occurred, were presented. Moreover, the influence of the aforementioned reduction on the joint stiffness was estimated.
Źródło:
Czasopismo Inżynierii Lądowej, Środowiska i Architektury; 2018, 65, 2; 187-196
2300-5130
2300-8903
Pojawia się w:
Czasopismo Inżynierii Lądowej, Środowiska i Architektury
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wstępne imperfekcje łukowe w analizie połaciowych stężeń poprzecznych
Analysis of the horizontal roof bracings in terms of the initial bow imperfection
Autorzy:
Niewiadomski, L.
Zamorowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/2068024.pdf
Data publikacji:
2017
Wydawca:
Politechnika Częstochowska
Tematy:
stężenia
imperfekcje
hala stalowa
concentrations
imperfections
steel hall
Opis:
W artykule zaprezentowano autorski sposób wyznaczania obciążenia stabilizującego dla stężeń, zastępującego wstępne wygięcia górnych pasów w modelu przestrzennym. Praktyczne zastosowanie tego sposobu przedstawiono na przykładzie obliczeń jednonawowej hali stalowej. Uzyskane wyniki porównano z wynikami otrzymanymi dla przestrzennych konstrukcji z imperfekcjami geometrycznymi, analizowanymi za pomocą geometrycznie nieliniowego modelu obliczeniowego oraz z wynikami dla płaskiego, normowego modelu obliczeniowego stężeń.
The author’s approach has been presented in this paper for the determination of the stabilizing load for bracing systems. Such an approach allows replacing the pre-bending of the upper flanges in the 3D model. An example of a practical application of this approach has been presented in this paper for a single-nave hall. The obtained results were compared to the geometrical non-linear calculations of 3D construction model with the geometrical imperfections and to the 2D calculation of the bracing systems model based on codes.
Źródło:
Zeszyty Naukowe Politechniki Częstochowskiej. Budownictwo; 2017, 23 (173); 231-244
0860-7214
Pojawia się w:
Zeszyty Naukowe Politechniki Częstochowskiej. Budownictwo
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Nośność stalowych elementów ściskanych i zginanych, pojedynczych i złożonych, z uwzględnieniem imperfekcji według Norm PN-EN 1993-1-1 i PN-EN 1090-2
Baring capacity of eccentrically compressed single and buit-up steel members including imperfections according PN-EN 1993-1-1 and PN-EN1090-2 standards
Autorzy:
Kowolik, B.
Zamorowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/2068485.pdf
Data publikacji:
2017
Wydawca:
Politechnika Częstochowska
Tematy:
słupy stalowe
imperfekcje
nośność
Eurokod 3
steel columns
imperfections
load capacity
Eurocode 3
Opis:
The results of static-strength analysis of the cantilever transmural and a complex column under bending and axial compression forces. The calculations have been conducted according to the second order theory (analysis), taking into account both the substitute imperfections presented in Eurocode 1993-1-1 and manufacturing tolerances based on PN-EN 1090-2 code. The results have been compared to those received from the formulas given in Eurokode 3.
Źródło:
Zeszyty Naukowe Politechniki Częstochowskiej. Budownictwo; 2017, 23 (173); 157-171
0860-7214
Pojawia się w:
Zeszyty Naukowe Politechniki Częstochowskiej. Budownictwo
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Podatność węzłów na przesuw w konstrukcjach prętowych na przykładzie dwóch przekryć pawilonów wystawowych
The susceptibility of joints to shifting in bar constructions on the example of two roofs of two exhibition halls
Autorzy:
Zamorowski, J.
Kowalik, B.
Powiązania:
https://bibliotekanauki.pl/articles/160819.pdf
Data publikacji:
2013
Wydawca:
Polski Związek Inżynierów i Techników Budownictwa
Tematy:
konstrukcja prętowa
węzeł
podatność na przesuw
hala wystawowa
przekrycie
bar construction
joint
susceptibility to shifting
exhibition hall
roof
Opis:
W dostępnych publikacjach dotyczących stalowych konstrukcji prętowych najczęściej analizowany jest wpływ podatności węzłów na obrót w konstrukcjach ramowych, a rzadziej wpływ podatności węzłów na przesuw w konstrukcjach kratowych. W przypadku konstrukcji ramowych dokonano różnego rodzaju standaryzacji opisu charakterystykM-ϕ węzłów, które pozwalają na obliczeniowe ujęcie problemu, a w konstrukcjach, gdzie decyduje podatność na przesuw brak jest takiej standaryzacji. W artykule, na przykładzie dwóch konstrukcji, które uległy katastrofie, przedstawiono wpływ podatności węzłów na przesuw nie tylko na dystrybucje sił wewnętrznych, ale również na zmianę ich topologii. Nietypowa konstrukcja kratowa przekrycia dachowego hali wystawowej uległa katastrofie w 2006 roku, a jednowarstwowe kopuły prętowe stanowiące przekrycie pawilonów wystawowych (zlokalizowanych na tym samym terenie co zawalona hala wystawowa) uległy awarii w latach 60. ubiegłego wieku.
The question most frequently addressed in the available literature on steel rod structures is the effect of joint vulnerability to rotation in frame structures, and less frequently, the impact of joint vulnerability to shifting in lattice structures. Various types of standardized description have been made of the characteristics of the M-ϕ joints in frame structures that permit a computational approach to the solution to the problem, yet no such standardization exists for constructions where this characteristic determines vulnerability to shifting.Based on the examples of two structures that suffered a construction disaster, this paper discusses the impact that joint vulnerability to shifting can have–not only on the distribution of internal forces, but also on changes in their topology. The unusual truss design of the roof of an exhibition hall suffered catastrophic collapse in 2006, and a monolayer rod dome providing the cover for exhibition halls (located on the same premises as the exhibition hall collapsed) failed in the ‘60s of the last century.
Źródło:
Przegląd Budowlany; 2013, R. 84, nr 7-8, 7-8; 61-66
0033-2038
Pojawia się w:
Przegląd Budowlany
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Damage Analysis of the Blade to the Rotor Hub Connection in the Wind Turbine
Autorzy:
Gremza, G.
Zamorowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/104789.pdf
Data publikacji:
2018
Wydawca:
Politechnika Rzeszowska im. Ignacego Łukasiewicza. Oficyna Wydawnicza
Tematy:
undersized bolts
mechanical properties
bolts
wind turbine
blade failures
model of joint
Opis:
The paper analyzes possible causes of bolts fracture in the connection of the blade to the hub of the wind turbine rotor. This failure has been growth shortly after the wind turbine was started, a few days after the storm. During the storm, electric power was turned off in the whole surrounding area for many hours, therefore it was impossible to control the device. After an initial analysis of failure modes in other wind turbines, it was found, that the bolts failure in the analysed case may be regarded as quite rare. Due to the fact that a significant part of bolts was broken brittle (flat fracture surfaces and lack of permanent elongation), it was decided to analyse the structure of the material in the direction of stress corrosion and hydrogen embrittlement. Among others, microscope analysis of fracture surfaces after their proper cleaning from corrosion products was carried out. The broken bolts were made as undersized, what is mainly used in fasteners intended for hot-dip galvanizing. On the basis of the purchase documentation analysis, it was presumed that the bolts were not galvanized by their manufacturer, which is obliged to perform the routine inspection in production process preventing the introduction of the hydrogenated bolts into the market. Besides the bolts examination, the scenarios of connection loads in extreme situations, in particular the impact of wind with high energy in the most unfavourable direction relative to the blade and nacelle, as well as the force resulting from the impact of the rotating blade on the tower that preceded the collapse of the whole structure, were considered. Conclusions from the performed tests and calculations by use of two calculation models of the connection were presented.
Źródło:
Czasopismo Inżynierii Lądowej, Środowiska i Architektury; 2018, 65, 2; 55-67
2300-5130
2300-8903
Pojawia się w:
Czasopismo Inżynierii Lądowej, Środowiska i Architektury
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A system consists of lifted steel tank and four assembly supports with variable assembly conditions
Autorzy:
Zamorowski, J.
Gremza, G.
Powiązania:
https://bibliotekanauki.pl/articles/178929.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
tank
method of erection
hydraulic jacking
disaster
Opis:
In the method of steel tank erection, consisting in assembling the roof and the next courses (segments) of the shell at the ground level, starting from the top one (the so-called hydraulic jacking-up method), the assembled part of the tank is lifted using assembly supports (towers, trestles), hydraulic jacks and ropes. Supports are located inside or outside the tank, and their bases are usually not anchored. During the assembly work, numerous contaminations can appear under the bases of the supports; therefore, boundary conditions of the system consisting of the elevated tank and assembly supports may change, influencing the field of displacements and stresses in the elements of this system. This article presents the results of numerical tests of an exemplary mounted tank – mounting support system – at various possible coefficients of friction between the bases of the supports and the ground. The influence of the support conditions on the effort of the essential elements of the system was assessed. Calculation difficulty was noted to determine the directions of horizontal responses of the supports. It was assumed that these directions did not change after exceeding the values of the friction forces. The analysed tank collapsed during its erection.
Źródło:
Studia Geotechnica et Mechanica; 2018, 40, 4; 263-269
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Problemy związane z nośnością i statecznością podestów wiszących wykonanych w latach 90. ub. wieku
Problems related to load+bearing capacity and stability of hanging platforms constructed in the 1990s
Autorzy:
Kowalik, B.
Niewiadomski, L.
Zamorowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/160641.pdf
Data publikacji:
2015
Wydawca:
Polski Związek Inżynierów i Techników Budownictwa
Tematy:
podest ruchomy wiszący
platforma robocza
konstrukcja
nośność
stateczność
analiza statyczno-wytrzymałościowa
suspended access equipment
working platform
construction
bearing capacity
stability
static-strength analysis
Opis:
Podesty wiszące powinny być zaprojektowane, wykonane oraz użytkowane zgodnie z odpowiednimi przepisami normowymi i przepisami dozoru technicznego. Projekt z obliczeniami statyczno-wytrzymałościowymi, badania techniczne oraz ciągły nadzór techniczny mają wyeliminować zagrożenia i niebezpieczeństwa, które mogłyby wystąpić w czasie jego eksploatacji. W referacie zwrócono uwagę na powyższe zagadnienie, a w szczególności na problemy związane z nośnością, statecznością oraz połączeniami sworzniowymi między segmentami jednego z typów pomostów, wykonanego w latach 90. ubiegłego wieku.
The hanging platforms should be designed, constructed and used in accordance with adequate standard regulations and technical supervision regulations. Design with static strength calculations, technical examinations as well as constant technical supervision are supposed to eliminate risks and hazards that could occur during exploitation of the platforms. This paper addresses the above issue, in particular, problems related to load-bearing capacity, stability and clevis fasteners between segments of a certain type of platform constructed in the 1990s.
Źródło:
Przegląd Budowlany; 2015, R. 86, nr 7-8, 7-8; 32-38
0033-2038
Pojawia się w:
Przegląd Budowlany
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-11 z 11

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies