Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Xu, H." wg kryterium: Autor


Tytuł:
The effect of injection pressure and strategy in a Jaguar V6 diesel engine
Autorzy:
Abdullah, N. R.
Mamat, R.
Rounce, P.
Wyszynski, M. L.
Tsolakis, A.
Xu, H. M.
Tian, G.
Powiązania:
https://bibliotekanauki.pl/articles/242414.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion
emissions
injection strategies
premixed combustion
ignition delay
Opis:
In recent years, the improvement of engine performance and emissions has become an extremely important concern. This study focuses on the injection strategy based on the injection pressure (IP) and duration between pilot injection and the main injection (dMI) using a multi cylinder common rail multiple injections diesel engine. The study was designed to produce improvements in fuel mixing via the injection strategy, to reduce the main ignition delay. This would contribute to a minimum amount of fuel burnt in the premixed combustion phase, leading to a reduction in emissions. Recent evidence shows that premixed combustion is significant in the controlling of emissions of nitrogen oxides (NOx) and soot. Six different IPs combined with a short and long dMI were compared in the attempt to improve engine performance and emissions. The engine performance was measured in terms of brake specific fuel consumption, ignition delay, heat release and peak in-cylinder pressure and emissions, specifically nitrogen oxides (NOx), total unburned hydrocarbons (THC), carbon monoxide (CO) and smoke emissions for each engine test condition. The evidence from this study shows that the effect of IP is more dominant than dMI in terms of peak cylinder pressure, heat release, brake specific fuel consumption and emissions. However, the dMI shows a strong effect at a higher engine speed.
Źródło:
Journal of KONES; 2009, 16, 2; 9-22
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the effect of variable compression ratios performance on opposed piston 2-stroke engine
Autorzy:
Alqahtani, A.
Wyszynski, M. L.
Mazuro, P.
Xu, H.
Powiązania:
https://bibliotekanauki.pl/articles/133658.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
opposed-piston
AVL BOOST
VCR
compression ratio
numerical simulation
tłok przeciwbieżny
stopień sprężania
symulacja numeryczna
Opis:
Numerous skills involving the introduction of (OP) opposed piston engine have been developed in the recent past. Indeed, novel techniques can help to improve the performance of the engine. The aim of this paper is to model and simulate a simple single-cylinder two-stroke opposed-piston engine and minimise fuel consumption and heat loss, using the software programme AVL BOOST™. AVL BOOST is an engine modelling software, which analyses the performance of a modelled single cylinder two-stroke opposed-piston engine by changing desired parameters. In order to meet this aim, experimental results from a unique engine are used to make a comparison with the results obtained from AVL BOOST model. Six combinations of compression ratios (12, 13.5, 15, 16.5, 18 and 19.5) are analysed in this study with the engine speed running at 420 rpm and 1500 rpm. In addition to the compression ratios, the effect of stroke-to-bore (S/B) ratios on OP2S performance is investigated. Various values of S/B ratios, whilst maintaining a constant swept volume, port geometry and combustion timing, and their effect on fuel consumption and heat loss are analysed in this study. A comparison between the two engine speeds with increasing combinations of compression ratios, and the S/B ratios revealed minimal differences in peak pressure, peak temperature, IMEP, ISFC, indicated efficiency and total heat loss. Detailed analyses of these parameters are highlighted in discrete sections of this paper.
Źródło:
Combustion Engines; 2017, 56, 4; 97-106
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Preparation and Characterization of Ultrafine HMX/TATB Explosive Co-crystals
Autorzy:
An, C.
Li, H.
Zhang, Y.
Ye, B.
Xu, C.
Wang, J.
Powiązania:
https://bibliotekanauki.pl/articles/358105.pdf
Data publikacji:
2017
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Przemysłu Organicznego
Tematy:
HMX
TATB
ultrafine co-crystals
ball milling
mechanical sensitivity
Opis:
An explosive co-crystal of 1,3,5,7-tetranitro-1,3,5,7-tetraazacyclooctane (HMX) and 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) was prepared by the ball milling method. The raw materials and co-crystals were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and Raman spectroscopy. Impact and friction sensitivity of the co-crystals were tested and analyzed. The results showed that the HMX/TATB co-crystals are spherical in shape and 100-300 nm in size. The co-crystals are different from anintimate mixture of HMX/TATB and they exhibit a new co-crystal structure. HMX/TATB co-crystals are formed by N-O···H hydrogen bonding between −NO2 (HMX) and −NH2 (TATB). The drop height of ultrafine HMX/TATB explosive co-crystals is 12.7 cm higher than that of ultrafine HMX, whilst the explosion probability of friction is 20% lower than that of ultrafine HMX. Ultrafine HMX/TATB explosive co-crystals are difficult to initiate under impact and friction conditions.
Źródło:
Central European Journal of Energetic Materials; 2017, 14, 4; 876-887
1733-7178
Pojawia się w:
Central European Journal of Energetic Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Development of evaluation system of coastline resource in Dafeng
Autorzy:
Chen, M.
Xu, C.
Chen, H.
Powiązania:
https://bibliotekanauki.pl/articles/259978.pdf
Data publikacji:
2017
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
coastline
Analytic Hierarchy Process
evaluation system
Opis:
Coastline is one type of valuable non-renewable resources. From the perspective of economic theory, it can gather population, promote traffic construction, and then improve the level of international trade. The research object of this paper is the coastline resource in Dafeng area. Firstly, we have a brief summary of the existing coastline evaluation literature, then introduce the location and natural attributes of the coastline resources in Dafeng. Following that, the Analytic Hierarchy Process (AHP) model is used to build the economic evaluation index system based on the characteristics of coastline in Dafeng. Specially, this index system consists of 6 factors, and a total of 41 detailed indicators were chosen including water depth, GDP, etc. On this basis, we use the assignment method to quantify the weight of each index, and calculate the comprehensive score of coastline resource by using the YAAHP software. The final conclusion is as follows: The total score of economic evaluation of coastline resource in Dafeng is 0.87. Therefore, the coastline resource in Dafeng will eventually be constructed a unique coastal economic zone, where the implemented port industrial projects will include shipbuilding, logistics, mechanical processing etc.
Źródło:
Polish Maritime Research; 2017, S 2; 181-187
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on electric spring control method considering noncritical load voltage constraint
Autorzy:
Chen, Y.
Ma, G.
Xu, U.
Zhang, H.
Ju, R.
Powiązania:
https://bibliotekanauki.pl/articles/140516.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
electric spring
noncritical load
voltage excursion
reactive power compensation
Opis:
With the increasing penetration rate of grid-connected renewable energy generation, the problem of grid voltage excursion becomes an important issue that needs to be solved urgently. As a new type of voltage regulation control method, electric spring (ES) can alleviate the fluctuations of renewable energy output effectively. In this paper, the background and basic principle of the electric spring are introduced firstly. Then, considering the influence of an electric spring on noncritical load voltage, noncritical loads are classified reasonably, and based on the electric spring phasor diagram, the control method to meet the noncritical load voltage constraint is proposed. This control method can meet the requirements of voltage excursions of different kinds of noncritical load, increase the connection capacity of the noncritical load and improve the voltage stabilization capacity of the electric spring. Finally, through the simulation case, the feasibility and validity of electric spring theory and the proposed control method are verified.
Źródło:
Archives of Electrical Engineering; 2018, 67, 4; 709-724
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A study of bubble-particle interactions in a column flotation process
Autorzy:
Cheng, G.
Shi, C.
Yan, X.
Zhang, Z.
Xu, H.
Lu, Y.
Powiązania:
https://bibliotekanauki.pl/articles/109635.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
particle
bubble
column flotation
collision
attachment
detachment
Opis:
Bubble-particle interactions play an important role in flotation. This study examines the behaviour of bubble clusters in a turbulent flotation cell. Particularly, the bubble-particle interaction characteristics in flotation are investigated. The bubble size in a flotation column was measured using an Olympus i-SPEED 3 high-speed camera. Relationships between the circulating volume, bubble size and bubble terminal velocity were discussed. Probabilities of collision, attachment, detachment and acquisition between bubbles and particles in different circulating volumes were calculated based on the flotation kinetic theory. Using the extended Derjaguin–Landau–Verwey–Overbeek (EDLVO) theory, the relationship between the potential energy and distance in bubble-particle interaction was analysed. The results demonstrated that as the circulating volume increased, the bubble size and velocity decreased. When the circulating volume increased from 0.253 to 0.495 m3/h, the bubble diameter decreased from 511 to 462 μm, and the corresponding bubble velocity decreased from 43.1 to 37.5 mm/s. When the circulating volume remained constant as the particle size increased, probabilities of collision, attachment, detachment and acquisition increased. When the particle size remained constant as the circulating volume increased, these probabilities also increased. At a constant circulating volume as the particle size increased, the absolute value of the total potential energy between the particle and bubble increased. When the distance between the bubble and particle was 30 nm, the energy barrier appeared.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 1; 17-33
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Energy feature of a multi-flow column flotation process
Autorzy:
Cheng, G.
Yu, Y.
Ma, L.
Xia, W.
Xu, H.
Powiązania:
https://bibliotekanauki.pl/articles/109768.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
flotation column
turbulent kinetic energy
turbulent dissipation rate
bubble
Opis:
A cyclonic-static micro-bubble flotation column (FCSMC) has been widely used in mineral separation. FCSMC includes countercurrent, cyclone and jet flow mineralization zones in a single column. In this study, the energy feature of the three different zones was compared. The turbulent flow was evaluated in terms of the turbulent kinetic energy (k) and the turbulent dissipation rate (ε). An appropriate computing model was determined by comparing the flow field value measured by PIV with the results of the Fluent numerical simulation. Jet flow separation exhibited the maximum k and ε values among the three columns, whereas counter-current separation displayed the minimum values. The high circulating volumetric flowrate means great energy input and turbulent intensity. The higher turbulent dissipation rate, the smaller the bubble is. The better performance of the FCSMC was mainly attributed to the multiple mineralization steps. The floatability of mineral particles gradually decreases with an increase in flotation time, the mineralization energy gradually increased to overcome the decrease in mineral floatability. By contrast, the countercurrent was beneficial for recovering the coarse particles, and the jet flow was beneficial for recovering the fine particles.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 2; 1266-1284
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
System for Calibrating Analogue Merging Units in Absence of Synchronization Signals
Autorzy:
Cheng, H.-M.
Huang, Q.-F.
Ji, F.
Xu, Q.
Liu, J.
Tian, Z.
Powiązania:
https://bibliotekanauki.pl/articles/221084.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
intelligent substation
analogue merging unit
peer-to-peer communication
calibration system
synchronization signal
Opis:
Synchronization signals are requisite for calibrating electrical measurement devices with digital output when using conventional calibration methods. However, since the signal sampling process of the analogue merging units (MUs) operating in an intelligent substation does not rely on external synchronization signals, accuracy calibration without the use of synchronization signals is of particular importance in order to guarantee the measurement accuracy in practical situations. So far, very little research on calibration systems independent of synchronization signals has been performed. This paper presents a design of the calibration system without dependence on synchronization signals. To verify the feasibility of the proposed design, the designed system and a conventional calibration system have been employed in testing the accuracy of the same analogue MU of a 0.2 accuracy class. The comparison of the test results shows that the differences of ratio errors are below 0.02%, and the maximum difference of phase errors is about 4′. This paper also provides a new efficient and significant calibration method which does not require any external synchronization signals.
Źródło:
Metrology and Measurement Systems; 2018, 25, 1; 129-138
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigation into particulate size distributions in the exhaust gas of diesel engines fuelled with biodiesel blends
Autorzy:
Chuepeng, S.
Theinnoi, K.
Xu, H. M.
Wyszynski, M. L.
York, A. P. E.
Hartland, J. C.
Qiao, J.
Powiązania:
https://bibliotekanauki.pl/articles/248072.pdf
Data publikacji:
2008
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
biodiesel
PM
combustion
diesel
PM size distribution
Opis:
Particulate matter (PM) size distributions in the exhaust gas of biodiesel blend fuelled diesel engines have been studied by experimenting firstly on a single cylinder equipped with a pump-line-injector injection system and secondly for comparison on a V6 DI engine equipped with a common rail fuel injection system. Both engines were operated with a biodiesel (RME) blend of B30 and ultra low sulphur diesel fuel (ULSD). Several engine load conditions with and without exhaust gas recirculation (EGR) were selected. Particulate number concentrations vs. the electrical mobility equivalent diameter were examined using a fast differential mobility spectrometer. The effect of engine operating conditions including EGR rates on particulate emissions has been investigated. It is found that PM sizes from combustion of B30 without EGR operation are generally smaller than those from ULSD while number concentrations are higher. This can result in lower PM mass estimates for the B30 case if due care is not taken. When EGR is applied to control nitrogen oxides emissions, both the total PM number and mass are increased and shifted toward the larger sizes for both fuels used in the test. The calculated total PM mass from B30 combustion is lower than in the ULSD case for all the tested engine operating conditions.
Źródło:
Journal of KONES; 2008, 15, 3; 75-82
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical Simulation of Dynamic Pressure and Displacement for the Top Part of Men’s Socks Using the Finite Element Method
Numeryczna symulacja ciśnienia dynamicznego i przesunięć w górnej części skarpet męskich
Autorzy:
Dan, R.
Dan, M. H.
Fan, X. R.
Chen, D. S.
Shi, Z.
Zhang, M.
Xu, L. B.
Powiązania:
https://bibliotekanauki.pl/articles/234002.pdf
Data publikacji:
2013
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
top part of socks
pressure
displacement
finite element
dynamic
górna część skarpetki
ciśnienie
przemieszczenie
elementy skończone
dynamika
Opis:
Numerical simulation of elastic human body deformation and dynamic pressure and displacement distribution are critical for pressure comfort and optimal design of apparel products. This paper demonstrates an analytical method for simulating dynamic pressure and displacement at the top part of men’s socks using the finite element method (FEM). The dynamic pressure is divided into two parts: the first is pressure with time, and the second is pressure with walking. Pressure with time is set at six periods (maximum 12 h). After measuring pressure values in different periods of time and simulating pressure and displacement distribution using ANSYS software, the tendency of pressure and displacement changes with time at the top part of men’s socks can be obtained. We divided the walking process into four phases to analyse the variation rule of pressure and displacement changes with movement in this research work. Meanwhile the lower leg cross section is divided into four equal regions according to the angle, and dynamic changes in the area shrinkage mass of each region can be calculated, respectively. All these solutions provide a theoretical reference for the optimal design of the top part of men’s socks.
Numeryczna symulacja elastycznej deformacji ciała ludzkiego, dynamicznego ciśnienia i rozkładu przesunięć są krytycznymi czynnikami komfortu i optymalnych rozwiązań ciśnieniowych wyrobów odzieżowych. Przedstawiono analityczną metodę symulacji ciśnień dynamicznych i przesunięć w górnej części męskich skarpet stosując metodę elementów skończonych. Analizę ciśnień dynamicznych przeprowadzono rozpatrując dwa stadia: zmiany ciśnienia w czasie i zmiany przy ruchu związane z chodzeniem. Na podstawie pomiarów ciśnienia i odkształcenia w określonych przedziałach czasowych określono rozkład odkształceń stosując program ANSYS. Proces chodzenia podzielono na cztery fazy. Wszystkie przeprowadzone badania i rozwiązania dostarczyły informacji dla przedstawienia optymalnego sposobu projektowania męskich skarpet.
Źródło:
Fibres & Textiles in Eastern Europe; 2013, 4 (100); 112-117
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
An investigation of mechanical properties of recycled coarse aggregate concrete
Badania właściwości mechanicznych betonu kruszywowego wtórnego wykonanego z użyciem kruszywa gruboziarnistego także pochodzenia wtórnego
Autorzy:
Deng, X. H.
Lu, Z. L.
Li, P.
Xu, T.
Powiązania:
https://bibliotekanauki.pl/articles/962346.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
beton
kruszywo gruboziarniste
kruszywo z recyklingu
stosunek wodno-cementowy
wskaźnik zamiany
wytrzymałość na ściskanie
wytrzymałość na rozciąganie
rozłupywanie
concrete
coarse aggregate
recycled aggregate
water-cement ratio
replacement rate
compression strength
tensile strength
splitting
Opis:
Recycling construction and demolition waste not only reduces project costs; and saves natural resources, but also solves the environmental threat caused by construction waste disposal. In this paper, C25 waste road concrete is used as an experimental material, the uniaxial compression strength and tensile splitting strength of C25 RAC whose coarse aggregate replacement rate is 0%, 25%, 50%, 75%, and 100% are tested under the condition that the water-to-cement ratio is 0.47, 0.55 and 0.61. The results show: (1) the uniaxial compression strength and tensile splitting strength decrease with the increase of RAC; (2) for concrete with the same water-to-cement ratio, when the coarse aggregate replacement rate changes from 0% to 50%, the uniaxial compression strength and tensile splitting strength of RAC changes slightly. When the coarse aggregate replacement rate changes from 50% to 100%, the uniaxial compression strength and tensile splitting strength of RAC decreases rapidly.
Recykling odpadów budowlanych oraz materiałów pochodzących z rozbiórek nie tylko zmniejsza koszty projektu i oszczędza zasoby naturalne, ale również zażegnuje zagrożenie dla środowiska spowodowane przez składowanie odpadów budowlanych. Szczególnie w odniesieniu do właściwości mechanicznych betonu z kruszywa gruboziarnistego poddanego recyklingowi, odpady betonu drogowego C25 są używane jako materiał eksperymentalny, pod warunkiem że stosunek wody do cementu wynosi 0,47, 0,55 i 0,61 oraz są przygotowane próbki betonu o wskaźniku zamiany betonu z kruszywa gruboziarnistego poddawanego recyklingowi wynoszącym 25%, 50%, 75% i 100% betonu z naturalnego kruszywa gruboziarnistego. Próbka to sześcian o wymiarach 150 × 150 × 150 mm. Przygotowaliśmy 6 próbek dla każdego wskaźnika zamiany betonu z kruszywa gruboziarnistego poddawanego recyklingowi. Przygotowano łącznie 90 próbek betonu. Próbki zostały usunięte 24 godziny po ustawieniu oraz były utwardzane w temperaturze 20°C i wilgotności 90% przez 28 dni. Następnie przeprowadzono próby ściskania jednoosiowego oraz wytrzymałości na rozciąganie przez rozłupywanie betonu z kruszywa poddawanego recyklingowi C25.
Źródło:
Archives of Civil Engineering; 2016, 62, 4/II; 19-34
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Seasonal dynamics in cambial activity and the formation of xylem and phloem in the branches of Cinnamomum camphora
Autorzy:
Dong, M.
Xu, Y.M.
Lin, H.
Li, X.Q.
Xia, Q.Q.
Powiązania:
https://bibliotekanauki.pl/articles/41385.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Instytut Dendrologii PAN
Tematy:
seasonal dynamics
cambial activity
formation
xylem
phloem
branch formation
tree
tropical tree
Cinnamomum camphora
wood formation
phenology
Opis:
The cambial activity and periodicity of secondary xylem and phloem formation have been less studied in tropical tree species than in temperate ones. Cambium activity is the only source of timber production. Studies on its activity and xylem formation can provide helpful data for dendrochronology and possible factors that control tree growth, the yield and quality of wood. Cinnamomum camphora is an important fast-growing tree for furniture and sculpture wood in South China. Its dynamics of cambial activity was not reported. During the growth season in 2011, five trees of Cinnamomum camphora plantation were monitored on the campus of Huazhong Agricultural University in central china (located on 113°41’ to 115°05’ E and 29°58’ to 31°22’ N). Sampling time was from 13, February 2011 to 13, February 2012. Some small stems of 15–20 cm length were selected to sample in the middle of 2–3 years old health branches in the central crown of these trees. The observational study found that the cambium of camphor trees was active from March to October and dormant from November to February. Onset of cambial cell division was observed in early March, one week after sprouting of new buds. The morphology of the cells and number of cell layers in the cambium zone varied throughout the year. In early March, cambium reactivated with the rising of temperature, the cell wall was relative thick. The number of cell layers increased from 2–3 in middle Feb. to 3–5. In June, the number of cell layers in cambium reached the maximum of 5–7 in a radial direction. In mid March, phloem cells began to differentiate, followed by xylem three weeks later. The number of cell layers in immature phloem and xylem increased dramatically before mid June and the increment of cell layers in xylem was almost fifth times of phloem in the differentiating process. The phloem cells mainly stopped dividing new cells in end of October, but xylem cells were still in the activity a week later. The annual activities of cambium was in accordance with the air mean temperature change in 2011–2012. The results showed that the cambial activity and formation of xylem and phloem were related to the environmental factors, especially the temperature.
Źródło:
Dendrobiology; 2016, 75
1641-1307
Pojawia się w:
Dendrobiology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Adsorption mechanism of sodium oleate on titanium dioxide coated sensor surface using quartz crystal microbalance with dissipation
Autorzy:
Fan, G.
Liu, J.
Cao, Y.
Feng, L.
Xu, H.
Powiązania:
https://bibliotekanauki.pl/articles/110014.pdf
Data publikacji:
2016
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
QCM-D
TiO2 coated sensor surface
sodium oleate
adsorption mechanism
Opis:
Quartz Crystal Microbalance with Dissipation (QCM-D) was firstly applied to investigate the adsorption mechanism of sodium oleate on TiO2 coated sensor surface. The effects of pH value, sodium oleate concentration, and temperature on TiO2 coated sensor surface were evaluated systematically using the QCM-D technique. Zeta potential, surface tension, adsorption isotherms, and adsorption thermodynamics were employed to characterize the adsorption process. The results showed the advantages of QCM-D on the investigation of the adsorption process. Additionally, the electrostatic equilibrium adsorption data was well matched to the Langmuir isotherm. Based on the thermodynamic analysis, adsorption was a spontaneous and endothermic physisorption process.
Źródło:
Physicochemical Problems of Mineral Processing; 2016, 52, 2; 597-608
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Truncated two-stage compound parabolic concentrator for collecting human diffuse transmission light
Autorzy:
Gao, J.
Han, G.
Lu, Q.
Ding, H.
Xu, J.
Sun, J.
Powiązania:
https://bibliotekanauki.pl/articles/174488.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
optical design
compound parabolic concentrator
CPC
non-imaging optics
near infrared spectroscopy
medicine optical instrument
Opis:
We propose an optical system employing a compound parabolic concentrator for near infrared spectroscope in noninvasive blood components testing. A truncated two-stage compound parabolic concentrator system is designed, which consists of a normal first-stage compound parabolic concentrator and a truncated second-stage compound parabolic concentrator. Using advanced ray tracing technique, the optical efficiencies of truncated two-stage compound parabolic concentrator system, ellipsoidal mirror system and non-optical-focusing mirror system are calculated to be 25.4%, 22.4% and 4.0%, respectively. Furthermore, the total length of truncated two-stage compound parabolic concentrator is only about 68 mm while the ellipsoidal mirror is 110 mm. It indicates that the truncated two-stage compound parabolic concentrator system enhances the ability of concentrating human diffuse transmission light, and it is a benefit to improve signal-to-noise ratio of noninvasive biochemical analysis system efficiently. Due to the advantage of small size, it tends to achieve a miniature instrument.
Źródło:
Optica Applicata; 2018, 48, 2; 325-335
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Pretreatment of coking wastewater by an adsorption process using fine coking coal
Autorzy:
Gao, L.
Li, S.
Wang, Y.
Gui, X.
Xu, H.
Powiązania:
https://bibliotekanauki.pl/articles/110417.pdf
Data publikacji:
2016
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
coking coal
coking wastewater
adsorption
COD
phenol
Opis:
A new technique for pretreatment of coking wastewater is introduced based on the concept of circular economy. Coal is fed into a coking system after adsorption. This study validates the feasibility of using coking coal to adsorb organic pollutants in coking wastewater. The sorption kinetics and equilibrium sorption isotherms of coking coal for removal of chemical oxygen demand (COD) and phenol from coking wastewater was also discussed in this paper. Gas chromatograph/mass spectroscopy (GC/MS) was used to detect changes in the quality of coking wastewater. The results showed that when coking coal dosage was 120 g/dm3, 65% of COD and 34% of phenol in waste water can be removed after 40 min of agitation. The surface functional groups of coking coal before and after adsorption were observed with a Fourier transform infrared spectrometer. The kinetics of COD and phenol adsorption from coking wastewater by coking coal fitted the pseudo second-order model. The adsorption process of coking coal can be classified into two categories, namely, rapid and slow. The Freundlich isotherm provided a better fit with all adsorption isotherms than the Langmuir isotherm. Coking coal could be a suitable low-cost adsorbent for recalcitrant organic pollutants.
Źródło:
Physicochemical Problems of Mineral Processing; 2016, 52, 1; 422-436
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies