Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Wiecek, B." wg kryterium: Autor


Tytuł:
Effect of sex on the meat quality of European wild boar (Sus scrofa scrofa)
Wpływ płci na jakość mięsa dzika europejskiego (Sus scrofa scrofa)
Autorzy:
Batorska, M.
Wiecek, J.
Kunowska-Slosarz, M.
Puppel, K.
Balcerak, M.
Slosarz, J.
Golebiewski, M.
Budzinski, A.
Kuczynska, B.
Rekiel, A.
Popczyk, B.
Powiązania:
https://bibliotekanauki.pl/articles/2501.pdf
Data publikacji:
2016
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Opis:
Forty carcasses (38.6-45.9 kg) from male and female (1:1) wild boar, which were shot in one hunting area during the 2014/2015 season, were studied. Samples of MLD were analysed for proximate chemical composition and fatty acid content of IMF as well as shear force and WHC. AI and TI index were calculated. Statistical analysis confirmed a significant (P≤0.05) effect of sex on the water content of MLD, which was higher in males than in females. Protein content of MLD was high and averaged 24%. Meat was lean with IMF below 2.0%. The PUFA/SFA ratio was similar in both groups of sex, and the dietetically beneficial n-6/n-3 PUFA ratio was less than 4:1 because the proportion of n-3 PUFA was high at 4.7-5.1 g/100 g fat. The effect of sex of wild boar on AI was significantly (P≤0.05) higher in males than in females. The results obtained show that the meat of wild boar of both groups of sex would be a rich source of protein in the human diet as well as a source of long-chain n-3 PUFA. The high level of long-chain n-3 PUFA is in line with dietary recommendations for the low n-6/n-3 PUFA. Due to its health-promoting benefits, wild boar meat may provide an alternative to the meat of farm animals.
Wpływ płci na jakość mięsa dzika europejskiego (Sus scrofa scrofa). Badania przeprowadzono na 40 tuszach (38.6-45.9kg) pozyskanych od dzików obu płci (1:1) odstrzelonych w jednym rejonie łowieckim centralnej Polski, w sezonie 2014/2015. W próbkach MLD określono podstawowy skład chemiczny i zawartość kwasów tłuszczowych w IMF oraz siłę cięcia i WHC, a także obliczono wartość indeksów AI i TI. Analiza statystyczna potwierdziła istotny (P≤0.05) wpływ płci na zawartość wody w MLD, która była większa u samców niż u samic. Zawartość białka w MLD była duża i wynosiła średnio 24%. Mięso było chude - poziom IMF wynosił poniżej 2.0%. Stosunek PUFA/SFA był zbliżony u obu płci. Korzystna ze względów dietetycznych relacja PUFA n-6/PUFA n-3 wynosiła mniej niż 4:1, ponieważ udział kwasów PUFA n-3 w IMF był wysoki i wynosił 4.7-5.1g/100g tłuszczu. Potwierdzono wpływ płci dzików na wartość indeksu AI, który był istotnie (P≤0.05) większy u samców niż u samic. Uzyskane wyniki wskazują, że mięso dzików obu płci może być bogatym źródłem białka w diecie człowieka, a także źródłem długołańcuchowych kwasów PUFA n-3. Wysoki poziom długołańcuchowych PUFA n-3 koresponduje z zaleceniami dietetyków odnośnie niskiego stosunku PUFA n-6/n-3. Ze względu na swoje walory prozdrowotne mięso dzika może stanowić alternatywę w porównaniu dla mięsa zwierząt gospodarskich.
Źródło:
Annals of Warsaw University of Life Sciences - SGGW. Animal Science; 2016, 55[1]
1898-8830
Pojawia się w:
Annals of Warsaw University of Life Sciences - SGGW. Animal Science
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A new software tool for transient thermal analysis based on fast IR camera temperature measurement
Autorzy:
Chatzipanagiotou, P.
Strąkowska, M.
De Mey, G.
Chatziathanasiou, V.
Więcek, B.
Kopeć, M.
Powiązania:
https://bibliotekanauki.pl/articles/114612.pdf
Data publikacji:
2017
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
transient thermal analysis
IR thermography
Nyquist plot
time constants
cumulative structure function
Opis:
A new software tool for transient thermal analysis based on thermographic measurement of temperature is presented. In the proposed approach, temperature change after applying or removing power can be measured by a thermal camera or any contact temperature sensor. The software calculates thermal impedance in frequency domain and represents it in the form of the Nyquist plot. In addition, thermal time constant spectrum and cumulative structure function are evaluated. The software was developed in Matlab environment using in-built procedures for transfer function estimation. For the validation of the proposed tool, the results are compared with ones obtained using commercially available software.
Źródło:
Measurement Automation Monitoring; 2017, 63, 2; 48-51
2450-2855
Pojawia się w:
Measurement Automation Monitoring
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Convection and radiation cooling of overhead power lines - laboratory verification using thermography
Autorzy:
Chatzipanagiotou, P.
Felczak, M.
De Mey, G.
Chatziathanasiou, V.
Więcek, B.
Powiązania:
https://bibliotekanauki.pl/articles/114618.pdf
Data publikacji:
2017
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
overhead power line
convection
laminar and turbulent airflow
radiation
IR thermography
Opis:
The thermal behavior of overhead power lines depends upon physical parameters, such as surface emissivity and line dimensions, as well as weather conditions. In this paper, the results of the convection and radiation cooling of a conductor that simulate a power line are presented. Laboratory experiments were conducted and the results were compared with the data obtained using empirical formulae from the literature. Both the laminar and the turbulent airflow were investigated.
Źródło:
Measurement Automation Monitoring; 2017, 63, 3; 107-110
2450-2855
Pojawia się w:
Measurement Automation Monitoring
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Lasers in industry 4.0
Lasery w koncepcji przemysłu 4.0
Autorzy:
Ciecińska, B
Więcek, T.
Gągała, I.
Powiązania:
https://bibliotekanauki.pl/articles/129530.pdf
Data publikacji:
2018
Wydawca:
Politechnika Rzeszowska im. Ignacego Łukasiewicza. Oficyna Wydawnicza
Tematy:
lasers
Industry 4.0 conception
agile production
lasery
koncepcja Przemysł 4.0
zwinna produkcja
Opis:
In this paper is presented the general idea of the industrial revolution which is called Industry 4.0. The main assumptions and an analysis of the laser use and requirements of lasers for flexible and agile production are presented. Examples of the different technological possibilities when lasers are joined with other machines and IT systems are described.
W pracy przedstawiono ogólną koncepcję rewolucji przemysłowej nazywanej „Przemysł 4.0”. Opisano jej podstawowe założenia oraz przeanalizowano zastosowania laserów w kontekście wymagań elastycznej i zwinnej produkcji. Przedstawiono przykład różnorodnych możliwości technologicznych, jakie dają lasery wspomagane innymi obrabiarkami oraz systemami informatycznymi.
Źródło:
Physics for Economy; 2018, 2, No.1; 21-26
2544-7742
2544-7750
Pojawia się w:
Physics for Economy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Importance of radiative heat transfer for infrared thermography measurements
Znaczenie radiacyjnej wymiany ciepła w pomiarach termowizyjnych
Autorzy:
De Mey, G.
Więcek, B.
Kałuża, M.
Olbrycht, R.
Strąkowski, R.
Strąkowska, M.
Powiązania:
https://bibliotekanauki.pl/articles/154589.pdf
Data publikacji:
2011
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
radiacyjna wymiana ciepła
termografia
promieniowanie podczerwone
heat transfer by radiation
thermography
infrared radiation
Opis:
The basics of heat transfer by radiation will be shortly outlined: Planck's law, Stefan Boltzmann's law, emissivity, construction of a black body, effective emissivity, reflection. Several applications for infrared thermography, basic physical principles of microbolometer detector, non uniformity correction without shutter and blocking the image and some original experiments will be discussed afterwards. The main conclusion of this work is that calibration of metrological cameras has to be performed for different temperature of their housing.
W artykule przedstawiono podstawy wymiany ciepła przez radiację: prawo Plancka, Stefana Boltzmanna, emisyjność materiałów, budowę ciała doskonale czarnego, efektywną emisyjność oraz prawo odbicia. Omówiono również niektóre aplikacje w termografii w podczerwieni, w których wykorzystuje się efekty radiacyjne. Omówiono fizyczne podstawy działania detektora mikrobolometrycznego, korekcję niejednorodności matrycy bolometrycznej bez migawki i blokowania obrazu oraz wybrane oryginalne eksperymenty. Przedstawiono wpływ promieniowania obudowy na działanie detektora i kamery termowizyjnej oraz zastosowanie pierścieni pośrednich w badaniach termowizyjnych.Niestety obudowa i pierścienie emitują pasożytnicze promieniowanie, które musi być uwzględnione w pomiarach termowizyjnych. Wnioskiem z pracy jest stwierdzenie, że w metrologicznej kamerze termowizyjnej, kalibracja powinna być przeprowadzona dla różnych wartości temperatury obudowy. Mówimy wówczas o korekcji RNU (ang. Residual Nonuniformity Correction). The work is an effect of design and building a prototype of the new infrared camera.
Źródło:
Pomiary Automatyka Kontrola; 2011, R. 57, nr 10, 10; 1112-1115
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of geometrical effects on the wall corner temperature in buildings
Wpływ efektów geometrycznych na rozkład temperatury w narożnikach ścian budynków
Autorzy:
De Mey, G.
Więcek, B.
Papagiannopoulos, I.
Chatziathanasiou, V.
Powiązania:
https://bibliotekanauki.pl/articles/154474.pdf
Data publikacji:
2011
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
pomiary termowizyjne
modelowanie termiczne
przenikanie ciepła przez przegrody budowlane
thermographic measurements
thermal modeling
heat transfer in buildings
Opis:
Thermographic measurements on a wall of a building show clearly a decrease of temperature in the neighborhood of a corner. The same problem has been numerically modelled by taking thermal conduction inside the wall and convection on both sides into account. The modelling confirms the experimental measurements. A simple physical explanation is that a corner provides more "material" for thermal conduction than a flat wall so that the temperature at the inside is lower. The cooling surface outside is larger then inside the corner, which results in higher heat transfer. The opposite phenomenon is observed at the outside of a building. The paper is mainly devoted to camera operators making thermal insulation inspections frequently. In many practical cases the reports contain the wrong interpretation of the effect presented in this paper.
Pomiary termowizyjne wewnątrz pomieszczeń budynków zazwyczaj pokazują spadek wartości temperatury w okolicy narożników. Ten problem termiczny został zbadany na drodze modelowania transferu energii przy uwzględnieniu konwekcyjnego przejmowania ciepła po obu stronach przegrody. Wyniki modelowania potwierdziły wyniki eksperymentów. Spadek wartości temperatury w narożach budynków jest zawsze obecny i wynika z większej masy przegrody i innej powierzchni przejmowania ciepła po obu jej stronach, a co za tym idzie zwiększonej wymiany ciepła na zewnątrz przegrody. Jak wykazały symulacje i pomiary wartość temperatury w narożniku może obniżyć się nawet o 20% w porównaniu w temperaturą na ścianie. Należy podkreślić, że przy przepływie ciepła do wewnątrz budynku efekt ten skutkuje wzrostem wartości temperatury w narożniku. Praca została przedstawiona głównie dla praktyków, którzy stosują termowizję do badań stanu izolacji w budownictwie. Często zdarza się, że niektórzy operatorzy kamer termowizyjnych niewłaściwie interpretują spadek wartości temperatury w narożnikach. Ich wnioski sugerują brak izolacji w narożniku, co nie zawsze jest prawdą.
Źródło:
Pomiary Automatyka Kontrola; 2011, R. 57, nr 10, 10; 1180-1182
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Lateral and Perpendicular Thermal Conductivity Measurement on Textile Double Layers
Pomiar przewodności cieplnej wzdłużnej i prostopadłej dla podwójnych warstw włóknin
Autorzy:
Felczak, M.
De Mey, G.
Więcek, B.
Michalak, M.
Powiązania:
https://bibliotekanauki.pl/articles/233529.pdf
Data publikacji:
2015
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
nonwoven
thermal conductivity
heat transfer
anisotropy
włókniny
przewodność cieplna
wymiana ciepła
anizotropia
Opis:
In this paper, the temperature distribution on a double layered fleece textile was measured experimentally with infrared thermography. A theoretical model based on the thin plate theory was to interpret the results measured. A two dimensional simulation of the same problem was carried out as well. By fitting the experimental data with the models, thermal conductivities in the lateral and perpendicular directions could be determined.
Przewodność cieplna włóknin jest bardzo istotnym parametrem. Właściwości niektórych z nich zmieniają się w zależności od kierunku. W pracy wykonano pomiary rozkładu temperatury po obu stronach dwuwarstwowej włókniny przy użyciu termografii w podczerwieni. Opracowano model teoretyczny, który został użyty do interpretacji wyników pomiarów. Opracowano dwuwymiarowy numeryczny model zjawisk cieplnych zachodzących we włókninie o tych samych wymiarach oraz warunkach brzegowych. Poprzez optymalizacyjne dopasowanie wyników obu modeli (analitycznego oraz numerycznego) wyznaczono przewodność cieplną włókniny dla dwóch wymiarów.
Źródło:
Fibres & Textiles in Eastern Europe; 2015, 4 (112); 61-65
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wyznaczanie przewodności cieplnej materiałów tekstylnych przy użyciu termowizji
Thermal conductivity evaluation of textile materials using infrared measurements
Autorzy:
Felczak, M.
Michalak, M.
Więcek, B.
Powiązania:
https://bibliotekanauki.pl/articles/154532.pdf
Data publikacji:
2011
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
przewodzenie ciepła
odwrotne zagadnienia termiczne
termowizja
heat transfer
inverse heat conduction problem
Opis:
W pracy przedstawiono nową metodę wyznaczania parametrów termicznych materiałów włókienniczych, w tym także anizotropowych. Do próbek włókienniczych dostarczana jest energia cieplna i mierzona jest wartość temperatury po obu stronach materiału. Praca jest kontynuacją badań właściwości ciepłoizolacyjnych materiałów włókienniczych w dynamicznych warunkach za pomocą metody termograficznej w wykorzystaniem luster [1-6]. W stanowisku pomiarowym, którego schemat przedstawiono w cytowanych pracach zostało zastosowane źródło energii cieplnej umożliwiające szybkie nagrzewanie badanej próbki. Wykonano pomiary termowizyjne rozkładu temperatury i na podstawie uzyskanych wyników oraz modelowania termicznego wyznaczono przewodność cieplną badanych włóknin.
A new method for evaluation of homogenous anisotropic textiles thermal parameters is presented in this paper. The research is a continuation of investigating the thermal properties of textile materials [1-6]. The thermal energy was supplied to textile materials and the temperature distribution on both surfaces of the textile waas recorded using an infrared camera. The setup enabled fast textile heating. A thermal energy impulse was supplied to nonwovens. Using the obtained results and the finite element model of heat conduction, the thermal conductivity of a textile is evaluated. In order to obtain the thermal conductivity, it is necessary to solve an inversed heat conduction problem. The parameterized direct heat conduction model is used to calculate it. The research included both isotropic and anisotropic textile materials. The work was performed as a part of the Research Project 3 T08E 050 28 financed by KBN, entitled "3688/B/T02/2009/36 "The elaboration of the method of evaluation of temperature dependent thermal parameters of smart textile materials".
Źródło:
Pomiary Automatyka Kontrola; 2011, R. 57, nr 10, 10; 1223-1226
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Termowizyjna metoda szacowania składników strat w miękkich materiałach ferromagnetycznych
A thermovision method for estimating components of losses in soft ferromagnetic materials
Autorzy:
Gmyrek, Z.
Olbrycht, R.
Więcek, B.
Strąkowska, M.
Tomalczyk, K.
Powiązania:
https://bibliotekanauki.pl/articles/155562.pdf
Data publikacji:
2013
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
straty
ferromagnetyk
termowizja
losses
ferromagnetic
thermovision
Opis:
Artykuł dotyczy wyznaczania składników strat mocy w ferromagnetyku miękkim, wiodącym zmienny w czasie strumień magnetyczny. Autorzy zaproponowali nowe rozwiązanie wykorzystujące kamerę termowizyjną do pomiaru temperatury na powierzchni blachy. Rozwiązanie to bazuje na fakcie, iż rozpraszana energia wynikająca ze strat jest przekształcana w ciepło. Dzięki temu można wyznaczyć składniki strat histerezowych i wiroprądowych wykonując pomiar przy różnych częstotliwościach strumienia magnetycznego.
: The paper presents a novel approach to estimating components of losses in soft ferromagnetic materials. The idea of the described solution is to use a thermovision camera to measure the increase of temperature of the metal plate surface. The temperature rises because of power losses caused by an alternating magnetic flux. This enables measurements at different frequencies to determine the components of the losses. It is required to apply a model of a metal plate [4] to estimate the amount of power, basing on a thermal response recorded by a thermal camera in time domain. Using (4) one can calculate the content of hysteresis and eddy-current losses. The concept of a test rig is shown in Fig. 2, while the obtained results are presented in Fig. 3. In that figure there are plots of power divided by frequency as a function of frequency obtained from thermal measurements and the plots are coherent with those prepared basing on the catalogue data. The results allow us to conclude that the presented method is a promising tool. Currently it is in a preliminary stage and the authors plan to develop it in the future.
Źródło:
Pomiary Automatyka Kontrola; 2013, R. 59, nr 9, 9; 885-887
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania serologiczne fenotypu "Bombay"
Serologicheskie issledovanija fenotipa "Bombajj"
Serologic determination of "Bombay" phenotype
Autorzy:
Górska, B.
Kabza, J.
Seyfried, H.
Tomczyk-Budzińska, H.
Wiecek, B.
Powiązania:
https://bibliotekanauki.pl/articles/2189728.pdf
Data publikacji:
1971
Wydawca:
Polskie Towarzystwo Diagnostyki Laboratoryjnej
Źródło:
Diagnostyka Laboratoryjna; 1971, 07, 2; 171-177
0867-4043
Pojawia się w:
Diagnostyka Laboratoryjna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Active Thermography in Qualitative Evaluation of Protective Materials
Autorzy:
Gralewicz, G.
Więcek, B.
Powiązania:
https://bibliotekanauki.pl/articles/90338.pdf
Data publikacji:
2009
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
protective material
active thermography
defects
Opis:
This is a study of the possibilities of a qualitative evaluation of protective materials with active thermography. It presents a simulation of a periodic excitation of a multilayer composite material. Tests were conducted with lock-in thermography on Kevlar® composite consisting of 16 layers of Kevlar® fabric reinforced with formaldehyde resin with implanted delamination defects. Lock-in thermography is a versatile tool for nondestructive evaluation. It is a fast, remote and nondestructive procedure. Hence, it was used to detect delaminations in the composite structure of materials used in the production of components designed for personal protection. This method directly contributes to an improvement in safety.
Źródło:
International Journal of Occupational Safety and Ergonomics; 2009, 15, 4; 363-371
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analytical-numerical model for the detection of structural defects by lock-in thermography
Model analityczno-numeryczny wykrywania defektów strukturalnych metodą termografii synchronicznej
Autorzy:
Gralewicz, G.
Owczarek, G.
Więcek, B.
Powiązania:
https://bibliotekanauki.pl/articles/258090.pdf
Data publikacji:
2006
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Technologii Eksploatacji - Państwowy Instytut Badawczy
Tematy:
thermography
non-destructive evaluation
CFRP
structural defects
thermal parameters
geometric parameters
Opis:
This paper presents the results of analytical-numerical modelling for the carbon-fibre-reinforced polymer (CFRP) structure using lock-in thermography. The method consists of the excitation of thermal effects in the tested structure caused by an external heat source. Simulations have been carried out to determine the optimum conditions for the lock-in evaluation in order to detect internal defects, measure their thickness and evaluate thermal properties. In the structure under study, a defect was simulated by inserting to the CFRP volume such materials as teflon and epoxy resin. Since many structures consist of CFRP, the rapid and remote identification of delaminations, impact damages and cracks is a topic of major concern. The results of our study indicate that a method is required for the maintenance of safety relevant structures (e.g. aerospace equipment and vehicles) where one needs to defect areas early enough to prevent catastrophic failure.
W pracy przedstawiono wyniki modelowania analityczno-numerycznego dla struktury karbon-włókno-wzmocniony polimer (CFRP) wykorzystując metodę termografii synchronicznej (lock-in). Metoda ta polega na wymuszaniu przez zewnętrzne źródło ciepła zjawisk termicznych zachodzących w badanej strukturze. Przeprowadzone symulacje miały na celu określenie optymalnych warunków badań metodą lock-in, w celu wykrywania defektów wewnętrznych, dokonywania pomiaru grubości ich warstw, a także badania właściwości cieplnych. W analizowanej strukturze defekt był symulowany przez wprowadzenie do objętości CFRP takich materiałów, jak teflon i żywica epoksydowa. Wyniki przedstawione w pracy potwierdzają przydatność metody przy ocenie struktur materiałowych (wykorzystywanych w lotnictwie oraz przemyśle samochodowym), gdzie odpowiednio wcześnie wykryte defekty struktur mogą zapobiec groźnym wypadkom.
Źródło:
Problemy Eksploatacji; 2006, 2; 65-79
1232-9312
Pojawia się w:
Problemy Eksploatacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badanie wpływu sygnału wymuszenia energetycznego na wynik analizy częstotliwościowej w technikach termografii aktywnej
Impact of energy excitation on frequency analysis for active thermography techniques
Autorzy:
Gralewicz, G.
Więcek, B.
Powiązania:
https://bibliotekanauki.pl/articles/157695.pdf
Data publikacji:
2009
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
termografia
impuls
periodyczne wymuszenie
thermography
impulse
periodic energy excitation
Opis:
Przedstawione w pracy wyniki dotyczą badania wpływu rodzaju sygnału wymuszenia energetycznego na wynik analizy częstotliwościowej sekwencji obrazów termograficznych oraz zestawienia wyników analiz Fouriera i falkowej dla materiałów jednorodnych termicznie. Na podstawie przeprowadzonych doświadczeń popartych modelowaniem komputerowym określono wpływ sygnału wymuszenia energetycznego periodycznego i impulsowego na wynik analizy częstotliwościowej.
Results of the excitation energy impact on frequency analysis for active thermography techniques are presented. Active thermography is a non-destructive evaluation method (NDE) in which tested items are excited with heat excitation, while infrared camera measures the changes of temperature distribution in time. Heat spreads in solid materials through diffusion which is strongly dependent on the thermal qualities of the tested material. The investigations included computer simulation and experimental tests. The analysis results of different excitation (frequency and time) for testing thermally conductive and isolative materials while using impulse and periodic energy signals are presented. The comparison between the Fourier and wavelets analysis for thermally homogeneous materials is discussed. The authors defined a parameter phase difference K? for signature defect in materials whose maximum value indicates the frequency of heat excitation. For isolative materials its value is much larger (the larger the thickness of the material, the greater the value of phase angle), while for conductive ones it is smaller, hence it is difficult to locate a defect in the material. The results of the excitation energy impact on the frequency analysis showed that periodic energy is more advantageous for isolative materials, whereas impulse energy is more useful for conductive materials.
Źródło:
Pomiary Automatyka Kontrola; 2009, R. 55, nr 11, 11; 902-905
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigations of Single and Multilayer Structures Using Lock-In Thermography - Possible Applications
Autorzy:
Gralewicz, G.
Owczarek, G.
Więcek, B.
Powiązania:
https://bibliotekanauki.pl/articles/91147.pdf
Data publikacji:
2005
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
lock-in and pulse thermography
NDT
transient state thermal modelling
effusivity and diffusivity
tkaniny na odzież ochronną
materiały na środki ochrony indywidualnej
materiały izolacyjne
termografia
Opis:
This paper presents a study of the possibilities of evaluating thermal parameters of single and multilayer structures using dynamic thermography. It also discusses potential uses of lock-in thermography. It presents a simulation of a periodic excitation of a multilayer composite material. In practice, the described methods can be employed in various applications, for example, in multilayer nonwoven microelectronic components manufactured from hemp fibers, chemical fibers, with an addition of electrically conducting fibers, and in medicine and biology. This paper describes tests conducted with lock-in thermography on carbon fibre reinforced composites with implanted delamination defects. Lock-in thermography is a versatile tool for non-destructive evaluation (NDE). Lock-in thermography is a fast, remote and non-destructive procedure. Hence, it has been used to detect delaminations in the composite structure of aircraft. This method directly contributes to an improvement in safety.
Źródło:
International Journal of Occupational Safety and Ergonomics; 2005, 11, 2; 211-215
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Lokalizacja obszarów nieciągłości materiału ochronnego - symulacje komputerowe i badania eksperymentalne
Location of discontinuities in protective material - computer simulations and experimental tests
Autorzy:
Gralewicz, G.
Więcek, B.
Powiązania:
https://bibliotekanauki.pl/articles/179105.pdf
Data publikacji:
2008
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
materiały ochronne
symulacje komputerowe
structure of the protective material
protective materials
computer simulation
Opis:
Materiały stosowane do produkcji wyrobów przeznaczonych do ochrony człowieka (m.in. materiały kompozytowe złożone z kilku warstw, zwane dalej materiałami ochronnymi) mają strukturę niejednorodną i anizotropową. Poprzez dobór odpowiednich składników można otrzymać materiał ochronny o odpowiednich parametrach i w ten sposób uzyskać np. wyższą odporność na udary lub lepsze pochłanianie energii. Właściwości materiału ochronnego zmieniają się, gdy w strukturze materiału pojawiają się (już podczas procesu technologicznego oraz na późniejszych etapach użytkowania) rozwarstwienia, pęcherzyki powietrza, pęknięcia itp. Ocena jakościowa struktury materiału ochronnego polega na wskazaniu defektów występujących w materiale. Do tego celu została wykorzystana technika termografii aktywnej. Termografia aktywna to metoda badań nieniszczących, w której badany obiekt pobudza się energią cieplną, a kamera termowizyjna mierzy zmienny w czasie rozkład temperatury. Ciepło w materiałach stałych rozchodzi się drogą dyfuzji, co jest ściśle powiązane z właściwościami termicznymi badanego materiału.
The structure of materials used in the production of components designed for personal protection (e.g. multi-layer composites, hereinafter called protective materials) is heterogeneous and anisotropic. By selecting suitable ingredients, protective materials of required parameters can be obtained, making it possible to achieve higher impact strength or enhanced energy absorption. The properties of protective materials change whenever the structure of the material (already during the technological process or at later application stages) features lamination, air bubbles, fractures, etc. A qualitative evaluation of protective material consists in identification of defects present in the material. To this aim, active thermography technology is employed.
Źródło:
Bezpieczeństwo Pracy : nauka i praktyka; 2008, 11; 12-15
0137-7043
Pojawia się w:
Bezpieczeństwo Pracy : nauka i praktyka
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies