Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Su, L." wg kryterium: Autor


Wyświetlanie 1-13 z 13
Tytuł:
Remote pipeline pumping transportation of cemented tailings backfill slurry
Przetłaczanie na znaczne odległości zawiesiny zawierającej odpady poflotacyjne oraz cement rurociągami z wykorzystaniem pomp
Autorzy:
Xiao, S.
Liu, Z.
Jiang, Y.
Li, C.
Sun, C.
Su, L.
Powiązania:
https://bibliotekanauki.pl/articles/219530.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
opory przepływu
przetłaczanie
eksperyment z wykorzystaniem linii obiegowej rurociągu
właściwości reologiczne
CFD (Computational Fluid Dynamics)
strong resistance
pipe pumping
pumping looping pipe experiment
rheological characteristic
CFD
Opis:
For most precious metal mines, cemented tailings backfill slurry (CTBS) with different cement-sand ratio and solid concentration are transported into the gobs to keep the stability of the stope and mitigate environmental pollution by mine tailing. However, transporting several kinds of CTBS through the same pipeline will increase the risk of pipe plugging. Therefore, the joint impacts of cement-sand ratio and solid concentration on the rheological characteristics of CTBS need a more in-depth study. Based on the experiments of physical and mechanical parameters of fresh slurry, the loss of pumping pressure while transporting CTBS with different cement-sand ratio, flux and solid mass concentration were measured using pumping looping pipe experiments to investigate the joint impacts of cement-sand ratio and solid concentration on the rheological characteristics of CTBS. Meanwhile, the effect of different stopped pumping time on blockage accident was revealed and discussed by the restarting pumping experiments. Furthermore, Fluent software was applied to calculate the pressure loss and velocity distribution in the pipeline to further analysis experimental results. The overall trends of the simulation results were good agreement with the experiment results. Then, the numerical model of the pipeline in the Sanshandao gold mine was conducted to simulate the characteristics of CTBS pipeline transportation. The results show that the pumping pressure of the delivery pump can meet the transportation requirements when there is no blockage accident. This can provide a theoretical method for the parameters optimizing in the pipeline transportation system.
W większości kopalń metali szlachetnych zawiesina zawierająca odpady poflotacyjne wraz z cementem w różnych proporcjach cementu i piasku oraz o różnym stężeniu części stałych transportowana jest do wyrobisk i zrobów, gdzie wykorzystywana jest następnie do stabilizacji w rejonie przodka, ponadto w ten sposób ogranicza się zanieczyszczenie środowiska odpadami poflotacyjnymi. Jednakże przetłaczanie różnych rodzajów zawiesin w tym samym układzie rurociągu zwiększa ryzyko zaczopowania rur. Zbadanie wpływu proporcji cementu do piasku w zawiesinie oraz stężenia części stałych na charakterystykę reologiczną zawiesiny wydaje się kwestią kluczową. W oparciu o badania eksperymentalne fizycznych i mechanicznych parametrów świeżej zawiesiny, dokonano pomiarów spadku ciśnienia pompowania w trakcie przetłaczania zawiesin o zawartości cementu i pisaku w różnych proporcjach, dla różnych natężeń przepływu i stężeń części stałych w eksperymentach z wykorzystaniem linii obiegowej rurociągu. Celem eksperymentu było określenie łącznego wpływu proporcji cementu do piasku oraz stężenia części stałych na właściwości reologiczne zawiesiny. Ponadto, przeanalizowano w jaki sposób długość przerw w procesie przetłaczania wpływa na zwiększenie ryzyka zatkania rur i przeprowadzono eksperymenty polegające na wznowieniu pracy pomp. Analizę wyników eksperymentów uzupełniono poprzez zastosowanie oprogramowania Fluent do obliczenia spadku ciśnienia w rurociągu oraz rozkładu prędkości. Wykazano, że wyniki symulacji pozostawały w dużej zgodności z wynikami eksperymentów. W kolejnym kroku opracowano model numeryczny rurociągu eksploatowanego w kopalni złota Sanshandao dla potrzeb symulacji procesu przetłaczania zawiesiny. Uzyskane wyniki wskazują, że ciśnienie tłoczenia w pompie jest na wymaganym poziomie gdy nie występuje zablokowanie przepływu w rurze, i wykorzystane być mogą jako uzupełnienie teoretycznych metod optymalizacji parametrów układu transportowania i przetłaczania zawiesiny.
Źródło:
Archives of Mining Sciences; 2018, 63, 3; 647-663
0860-7001
Pojawia się w:
Archives of Mining Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on an Optimal Design of Mechanical Properties for PP/PET Nonwovens
Poszukiwanie optymalnej struktury włóknin PP/PET dla poprawy ich właściwości mechanicznych
Autorzy:
Su, T. L.
Gui-Bing, H.
Powiązania:
https://bibliotekanauki.pl/articles/232529.pdf
Data publikacji:
2012
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
włókna igłowane
maszyna igłująca
optymalizacja
metoda Taguchi
analiza
needle-punched nonwovens
optimisation
Taguchi approach
grey relational analysis
analysis
Opis:
This study aimed to determine the optimal process parameters of needle-punched nonwoven fabrics, and obtain the maximal strength of needle-punched nonwoven fabrics. The Taguchi approach and grey relational analysis were used to solve the multi-quality optimisation problem and determine the optimal process parameter combination of needlepunched nonwoven fabrics. The L9 orthogonal array was used to design parameters that affect the needle-punched nonwoven fabric process, including the folding machine oscillating speed, folding machine conveying speed, needle-punch depth, and needle-punch density. Then grey relational analysis was used to overcome the single quality characteristic disadvantage of the Taguchi approach, and the optimal process parameter combination of multiple quality characteristics was obtained from the response graph of the analysis. The quality characteristics of this experiment are the nonwoven fabric tearing strength and tensile strength. Signal-to-noise ratios (S/N ratio) were calculated and an analysis of variance (ANOVA) was conducted to analyse the experiment results. The results of ANOVA showed that the factors with a significant effect on the quality characteristics of needlepunched nonwoven fabrics included the needle-punch depth and needle-punch density. In other words, by controlling these factors the quality characteristics of the needle-punched nonwoven fabrics could be controlled effectively. Finally, the 95% confidence interval of the verification experiment proved that this experiment was reliable and reproducible
Celem pracy było wyznaczenie optymalnych parametrów procesu, otrzymywanie włóknin igłowanych dla uzyskania optymalnych właściwości, w tym możliwie jak największej wytrzymałości mechanicznej. Zastosowano metodę Taguchi i analizę zbiorów rozmytych. Jako parametry wyjściowe przyjęto: prędkość oscylacji maszyny igłującej, szybkość transportową, głębokość igłowania oraz gęstość przeigłowań. Optymalizację przeprowadzano pod kątem uzyskania maksymalnej wytrzymałości włókniny oraz odporności na rozrywanie. Przy analizie określano poziom szumów sygnału oraz przeprowadzono analizę wariancji. Stwierdzono, że najistotniejszymi parametrami, które muszą być kontrolowane w czasie produkcji włókniny są głębokość i gęstość przeigłowań.
Źródło:
Fibres & Textiles in Eastern Europe; 2012, 5 (94); 75-79
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Biomechanical simulation of needle insertion into cornea based on distortion energy failure criterion
Autorzy:
Su, P.
Yang, Y.
Huang, L.
Powiązania:
https://bibliotekanauki.pl/articles/306549.pdf
Data publikacji:
2016
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
rogówka
biomechanika
symulacja matematyczna
cornea
biomechanics
insertion force
suture
mathematical simulation
Opis:
Purpose: This paper is mainly about biomechanical behavior of needle insertion into cornea, and proposes a failure criterion to simulate the insertion process which has attracted considerable attention due to its importance for the minimally invasive treatment. Methods: In the process of needle insertion into cornea, tiny and complex insertion force is generated due to contact between needle and soft tissue. Based on the distortion energy theory, there is proposed a failure criterion of corneal material that can solve contact problem between rigid body and biological tissue in insertion simulation, where Cauchy stress of corneal material is the key to numerical calculation. A finite element model of in vivo cornea is built, and the cornea constrained by sclera is simplified to two layers containing epithelium and stroma. Considering the hyper-viscoelastic property of corneal material, insertion simulation is carried out. Results: By insertion experiment, the insertion force increases with insertion depth accompanying obvious fluctuations. Different insertion forces are generated at different speeds. The punctured locations are obvious in the force-displacement curves. The results of insertion simulation are generally consistent with experimental data. Maps of von Mises stress reflect the tissue injury of the cornea during insertion process, and punctured status corresponds to the point in the curves. Conclusions: The ability of this study to reproduce the behavior of needle insertion into cornea opens a promising perspective for the control of robotic surgery operation as well as the real-time simulation of corneal suture surgery.
Źródło:
Acta of Bioengineering and Biomechanics; 2016, 18, 1; 65-75
1509-409X
2450-6303
Pojawia się w:
Acta of Bioengineering and Biomechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fuzzy Availability Assessment for Discrete Time Multi-State System under Minor Failures and Repairs by Using Fuzzy Lz -transform
Wykorzystanie rozmytej transformaty do oceny rozmytej gotowości eksploatacyjnej dyskretnego w czasie systemu wielostanowego działającego w trybie drobnych uszkodzeń i napraw
Autorzy:
Hu, L.
Zhang, Z.
SU, P.
Peng, R.
Powiązania:
https://bibliotekanauki.pl/articles/301353.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
czas dyskretny
model Markowa
rozmyta transformata
system wielostanowy
dostępność
discrete time
Markov model
fuzzy Lz-transform
Multi-State System
availability
Opis:
W niniejszej pracy badano metodę oceny dynamicznej, rozmytej gotowości eksploatacyjnej (dostępności) dyskretnego w czasie systemu wielostanowego pracującego w trybie drobnych uszkodzeń i napraw. Tradycyjnie zwykło się zakładać, że analiza niezawodności dostarcza dokładnych danych niezawodnościowych na temat danego dyskretnego w czasie komponentu/systemu. W praktyce inżynieryjnej jednak trudno jest uzyskać dokładne dane do oceny właściwości komponentu/systemu. W niniejszej pracy zaproponowano jak problem ten można rozwiązać wykorzystując do oceny dynamicznej gotowości dyskretnego w czasie systemu wielostanowego, teorię zbiorów rozmytych. Rozmyty model Markowa z dyskretnym czasem i rozmytą macierzą prawdopodobieństw przejść zastosowano do analizy rozmytego prawdopodobieństwa stanu każdego elementu w dowolnym czasie dyskretnym. Opracowano rozmytą transformatę Lz rozmytego, dyskretnego w stanach i czasie łańcucha Markowa, która pozwala poszerzyć transformatę Lz modelu Markowa dyskretnego w stanach i ciągłego w czasie o zbiory ostre. W oparciu o metodę alfa przekrojów oraz rozmytą transformatę Lz, obliczono dynamiczną rozmytą gotowość eksploatacyjną systemu, wykorzystując do tego celu technikę programowania parametrycznego. Zastosowanie proponowanej metody zilustrowano na przykładzie liczbowym analizując układ przesyłu.
This paper studies assessment approach of dynamic fuzzy availability for a discrete time multi-state system under minor failures and repairs. Traditionally, it was assumed that the exact reliability data of a component/system with discrete time are given in reliability analysis. In practical engineering, it is difficult to obtain precise data to evaluate the characteristics of a component/system. To overcome the problem, fuzzy set theory is employed to deal with dynamic availability assessment for a discrete time multi-state system in this paper. A fuzzy discrete time Markov model with fuzzy transition probability matrix is proposed to analyze the fuzzy state probability of each component at any discrete time. The fuzzy Lz-transform of the discrete-state discrete-time fuzzy Markov chain is developed to extend the Lz-transform of the discrete-state continuous-time Markov model with crisp sets. Based on the α-cut approach and the fuzzy Lz-transform, the dynamic fuzzy availability of the system is computed by using parametric programming technique. To illustrate the proposed method, a flow transmission system is analyzed as a numerical example.
Źródło:
Eksploatacja i Niezawodność; 2017, 19, 2; 179-190
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of large particle sizes using a machine vision system
Autorzy:
Zhang, Z.
Yang, J.
Su, X.
Ding, L.
Powiązania:
https://bibliotekanauki.pl/articles/109404.pdf
Data publikacji:
2013
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
machine vision
particle size distribution
equivalent ellipse
best-fit rectangle
representing analysis
Opis:
Many methods based on machine vision were used to estimate coarse particles size distribution in recent years, but comparison of accuracy parameters representing particle size has not been carried out and a related representing analysis has not been yet proposed. Nine parameters were investigated. The results indicated the minor axis of equivalent ellipse and breadth of the best-fit rectangle were the most suitable for representing particle size. The former accuracy ratio was 86.43% and the latter accuracy ratio was 85.39%, while the accuracy of other parameters was less than 70%. A related representing analysis was proposed to explain this phenomenon. This research is instructive and meaningful for the size distribution estimation by machine vision.
Źródło:
Physicochemical Problems of Mineral Processing; 2013, 49, 2; 397-405
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on Friction and Wear Characteristics of Aluminum Alloy Hydraulic Valve Body and Its Antiwear Mechanism
Autorzy:
Rong, L.
Lunjun, Ch.
Ming, Su
Qi, Z.
Yong, Liu
Powiązania:
https://bibliotekanauki.pl/articles/382468.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminum alloy
hydraulic valve body
oil leakage
friction and wear
stop aluminium
korpus zaworu hydraulicznego
wycieki oleju
tarcie i zużycie
Opis:
In order for the working status of the aluminum alloyed hydraulic valve body to be controlled in actual conditions, a new friction and wear design device was designed for the cast iron and aluminum alloyed valve bodies comparison under the same conditions. The results displayed that: (1) The oil leakage of the aluminum alloyed hydraulic valve body was higher than the corresponding oil leakage of the iron body during the initial running stage. Besides during a later running stage, the oil leakage of the aluminum alloyed body was lower than corresponding oil leakage of the iron body; (2) The actual oil leakage of different materials consisted of two parts: the foundation leakage that was the leakage of the valve without wear and wear leakage that was caused by the worn valve body; (3) The aluminum alloyed valve could rely on the dust filling furrow and melting mechanism that led the body surface to retain dynamic balance, resulting in the valve leakage preservation at a low level. The aluminum alloy modified valve body can meet the requirements of hydraulic leakage under pressure, possibly constituting this alloy suitable for hydraulic valve body manufacturing.
Źródło:
Archives of Foundry Engineering; 2017, 17, 1; 207-215
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Design and analysis of interior composite-rotor bearingless permanent magnet synchronous motors with two layer permanent magnets
Autorzy:
Sun, X.
Su, B.
Chen, L.
Yang, Z.
Li, K.
Powiązania:
https://bibliotekanauki.pl/articles/200490.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
bearingless motor
permanent magnet motor
finite element analysis
cogging torque
static electromagnetic characteristics
silnik z magnesem trwałym
analiza elementów skończonych
moment skręcający
właściwości elektromagnetyczne
silnik bezłożyskowy
Opis:
In this paper, a new type of interior composite-rotor bearingless permanent magnet synchronous motors (BPMSMs) with two layer permanent magnets (PMs) is proposed. In order to reduce the torque ripple of this kind of motors, the sizes of PMs are optimized. Moreover, the magnetic field analysis of the interior composite-rotor BPMSM with two layer PMs is carried out by the finite element method (FEM). The corresponding static electronic magnetic characteristics at no load, including magnetic field, PM flux linkage and inductance, are studied in detail. In addition, electromagnetic torque characteristics and suspension force characteristics are also investigated thoroughly. The results of the analysis and simulation lay a significant foundation for further research on the interior composite-rotor BPMSMs with two layer PMs.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2017, 65, 6; 833-843
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Magnified holographic projection based on spatial light modulators
Autorzy:
Su, Y.
Cai, Z.
Shi, L.
Zhou, F.
Chen, H.
Wu, J.
Powiązania:
https://bibliotekanauki.pl/articles/174247.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
holographic display
spatial light modulators
computer-generated holograms
magnified holographic projection
Opis:
In this paper, a magnified holographic projection based on spatial light modulators is proposed and implemented by combining four magnification methods, including similarity principle of Fourier transform, spatial division, digital lens, and image splicing methods. The Fourier holographic display system is constructed for the experimental verification of the proposed methods. With such four methods of holographic magnification, the reconstruction image can be magnified to 10 × 5 times in two-dimensional directions, which is verified by the experiments. Furthermore, the undesirable light of holographic projection is eliminated by encoding the linear phase onto the computer-generated holograms. The experimental results prove that the proposed system can realize magnified holographic projection with good reconstructed quality, which provides a promising potential for the dynamic holographic projector.
Źródło:
Optica Applicata; 2018, 48, 4; 589-600
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Three-dimensional biomechanical modeling and simulation of trephine cutting cornea for keratoplasty
Autorzy:
Su, P.
Lu, D.
Deng, S.
Zhang, L.
Hao, Y.
Yang, Y.
Powiązania:
https://bibliotekanauki.pl/articles/307486.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
rogówka
biomechanika
kryterium wytężeniowe
FEM
cornea
biomechanics
failure criterion
finite element simulation
Opis:
Trephination is one of the basic operations of keratoplasty, and the biomechanical mechanism of the operation can be revealed based on three-dimensional modeling and simulation of trephine cutting cornea. Methods: Based on the analysis of the physical and biomechanical characteristics of corneal trephination, a three-dimensional numerical model of corneal trephination is built, where the cornea can be simplified to two layers structure including stroma and epithelium, and the trephine cuts the cornea under the vertical motion load and the rotational motion load. A three-dimensional failure criterion of corneal material is proposed based on the yield strength theory. On this basis, trephination simulation is carried out, and the units of corneal material are removed from the model when they meet the defined failure criterion. Results: Under the given parameters including the velocity, the angle and the angular velocity, the trephine force curves, include the linear cutting force and the rotary cutting force are obtained, and show the change of the forces with displacement during the process of trephination simulation. The maps of the equivalent stress show the destruction and deformation of the cornea. Then, the experiment of robotic trephination is carried out under the same parameters and the effectiveness of the simulation is evaluated. Conclusions: Based on mechanics theory and finite element method, the process of trephine cutting cornea has been reproduced, and the interaction mechanism is revealed, which lays the foundation for the development of real-time simulation and virtual system of the corneal surgery.
Źródło:
Acta of Bioengineering and Biomechanics; 2018, 20, 2; 23-33
1509-409X
2450-6303
Pojawia się w:
Acta of Bioengineering and Biomechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Detection of multilayer cavities by employing RC-DTH air hammer system and cavity auto scanning laser system
Wykrywanie pustek obejmujących kilka warstw podłoża przy wykorzystaniu układu złożonego z młota pneumatycznego wgłębnego z odwrotnym obiegiem płuczki RC-DTH i automatycznego układu laserowego do skanowania
Autorzy:
Luo, Y.
Li, L.
Peng, J.
Yin, K.
Li, P.
Gan, X.
Zhao, L.
Su, W.
Powiązania:
https://bibliotekanauki.pl/articles/219542.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
multilayer cavities detection
RC-DTH air hammer
drill bit
cavity auto scanning laser system
wykrywanie pustek przechodzących przez liczne warstwy górotworu
młot pneumatyczny wgłębny z odwrotnym obiegiem płuczki
urządzenie wiertnicze
laserowy skaner pustek
Opis:
The subterranean cavities are seriously threatened to construction and mining safety, and it’s important to obtain the exact localization and dimensions of subterranean cavities for the planning of geotechnical and mining activities. Geophysical investigation is an alternative method for cavity detection, but it usually failed for the uncertainly solution of information and data obtained by Geophysical methods. Drilling is considered as the most accurate method for cavity detection. However, the conventional drilling methods can only be used for single cavity detection, and there is no effective solution for multilayer cavities detection have been reported. In this paper, a reverse circulation (RC) down-the-hole (DTH) air hammer system with a special structured drill bit is built and a cavity auto scanning laser system based on laser range finding technique was employed to confirm the localization and dimensions of the cavities. This RC-DTH air hammer system allows drilling through the upper cavities and putting the cavity auto scanning laser system into the cavity area through the central passage of the drill tools to protect the detection system from collapsing of borehole wall. The RC-DTH air hammer system was built, and field tests were conducted in Lanxian County Iron Ore District, which is located in Lv Liang city of Shan Xi province, the northwest of china. Field tests show that employing the RC-DTH air hammer system assisted by the cavity auto scanning laser system is an efficiency method to detect multilayer cavities.
Podziemne wgłębienia i pustki stanowią poważne zagrożenie dla budowli oraz dla działalności górniczej; dlatego też podstawowym zagadnieniem jest ich dokładna lokalizacja i określenie wymiarów. Jest to niezbędne dla planowania prac geotechnicznych i wydobywczych. Badania geofizyczne są alternatywną metodą wykrywania podziemnych zagłębień, zazwyczaj jednak okazują się nieskuteczne ze względu na niepewność rozwiązań oraz danych uzyskiwanych za pomocą metod geofizycznych. Wykonanie odwiertu jest najdokładniejszą metodą wykrywania zagłębień i pustek, jednakże konwencjonalne metody prowadzenia wierceń pozwalają na wykrycie jednego tylko zagłębienia, nie ma też skutecznego rozwiązania kwestii istnienia zagłębień i pustek przechodzących przez liczne warstwy górotworu. W pracy omówiono zastosowanie układu młota pneumatycznego wgłębnego z odwrotnym obiegiem płuczki, wyposażonego w odpowiednie urządzenie wiertnicze, oraz układu skanera laserowego wykorzystującego technikę dalmierza do potwierdzania lokalizacji pustek i ich wymiarów. Prezentowany młot umożliwia dokonanie odwiertu w zagłębieniach i pustkach znajdujących się w warstwach wierzchnich, następnie w zagłębieniu tym umieszczane jest laserowe urządzenie skanujące powierzchnię komory wprowadzane poprzez główny kanał w urządzeniu wiertniczym, tak by zabezpieczyć skaner na wypadek osunięcia się ścian otworu. Układ składający się z młota pneumatycznego zbudowano i przetestowano w warunkach polowych w zagłębiu miedziowym w okręgu Lanxian, w pobliżu miasta LV Liang w prowincji Shan Xi, w północno-zachodnich Chinach. Badania przeprowadzone w terenie wykazały, że zastosowanie układu złożonego z młota pneumatycznego wgłębnego RC-DTH wraz z laserowym skanerem jest skuteczną metodą wykrywania pustek przechodzących przez liczne warstwy.
Źródło:
Archives of Mining Sciences; 2015, 60, 4; 1041-1052
0860-7001
Pojawia się w:
Archives of Mining Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Friction and Wear Behavior of 201HT Cast Aluminum Alloy with Various Competitive Material
Autorzy:
Li, R.
Chen, L. J.
Su, M.
Zeng, Q.
Li, H.
Liu, Y.
Powiązania:
https://bibliotekanauki.pl/articles/382627.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
casting
aluminum alloy
friction and wear
competitive material
odlewanie
stop aluminium
tarcie i zużycie
materiał konkurencyjny
Opis:
The friction and wear properties of 201HT aluminum alloys and the corresponding competitive coupons were tested on an electro-hydraulic servo face friction and wear testing machine (MM-U10G). The microstructures of the competitive coupons were investigated by scanning electron microscopy (SEM) and consequently the corresponding friction and wear mechanisms were studied. The results demonstrated that: (1) the best competitive material of friction and wear performance of the 201HT was the 201HTC. (2) the 201HTC modified by carbon following the initial mill for oil storage of the micro-groove to be produced, increased the corresponding lubrication performance reduced the friction coefficient and wear rate effectively. (3) the 201HT-201HTC could obtain both better friction and wear mainly due to the initial process of grinding following the 201HT plastic deformation occurred in the surface and the formation of a series of re-melting welding points, whereas the 201HT material hardness would be similar to the 201HTC material hardness, which led into the competitive material friction and wear performance improvement.
Źródło:
Archives of Foundry Engineering; 2017, 17, 2; 55-62
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dispersion-compensating en/decoder for a time-spreading/wavelength-hopping optical code-division multiplexing (OCDM) system
Autorzy:
Zheng, J.
Wang, R.
Pu, T.
Lu, L.
Fang, T.
Su, Y.
Li, L.
Yang, Q.
Chen, X.
Powiązania:
https://bibliotekanauki.pl/articles/174365.pdf
Data publikacji:
2013
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
optical code-division multiplexing (OCDM)
fiber Bragg grating (FBG)
dispersion
Opis:
A novel dispersion-compensating fiber Bragg grating (FBG)-based en/decoder is proposed to compensate both the out-band and in-band dispersion in a time-spreading/wavelength-hopping (TS/WH) optical code-division multiplexing (OCDM) system. The experimental realization of such en/decoders only needs a uniform-pitch phase mask and a sub-micrometer precision moving stage. Such an en/decoder pair with the ability of compensating the dispersion of transmission in 20-km single mode fiber (SMF) is simulated and experimentally fabricated. Both the simulation and experimental results show that the decoded pulse can be recovered without any distortion owing to the elimination of dispersion.
Źródło:
Optica Applicata; 2013, 43, 3; 485-495
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Digital control system design for bearingless permanent magnet synchronous motors
Autorzy:
Sun, X.
Shi, Z.
Yang, Z.
Wang, S.
Su, B.
Chen, L.
Li, K.
Powiązania:
https://bibliotekanauki.pl/articles/202311.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
BPMSMs
cyfrowy system kontroli
podwójnie zamknięty system regulacji prędkości
projektowanie oprogramowania
projekt sprzętu
digital control system
double-closed speed regulating system
software design
hardware design
Opis:
This study investigates a digital control system which is used in bearingless permanent magnet synchronous motors (BPMSMs). Compared with traditional permanent magnet synchronous motors, a BPMSM is characterized by higher speed and no mechanic friction. Therefore, the application value of the latter to the special area is higher than that of the former. An analysis from previous work on the BPMSM had proved its feasibility, and some performances such as suspension force, inductance and so on were also investigated. Based on this analysis, this study focuses on solving control problems in practical applications by designing a control system. The control system design includes overall schematic, hardware and software designs. Main software systems, including the force/current transform module and closed loop control module for radial displacement, are analyzed. Interface circuit for radial displacement, current feedback circuit and dead zone protection circuit are designed for the hardware system. Finally, several performance experiments have been conducted to verify the effectiveness of the designed digital control system. Experiment results indicate that the rotor has unique characteristics, such as stable suspension performance, good start-of-suspension performance, and rapid anti-disturbance features.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2018, 66, 5; 687-698
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-13 z 13

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies