Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Shao, F." wg kryterium: Autor


Wyświetlanie 1-2 z 2
Tytuł:
Effects of selenium on the growth and photosynthetic characteristics of flue-cured tobacco (Nicotiana tabacum L.)
Autorzy:
Jiang, C.
Zu, C.
Shen, J.
Shao, F.
Li, T.
Powiązania:
https://bibliotekanauki.pl/articles/57536.pdf
Data publikacji:
2015
Wydawca:
Polskie Towarzystwo Botaniczne
Tematy:
selenium
growth
photosynthesis
tobacco plant
Nicotiana tabacum
carboxylation efficiency
Opis:
The objective of this study was to investigate the effect of Selenium (Se) supply (0, 3, 6, 12, 24 mg kg−1) on the growth, photosynthetic characteristics, Se accumulation and distribution of flue-cured tobacco (Nicotiana tabacum L.). Results showed that low-dose Se treatments (≤6 mg kg−1) stimulated plant growth but high-dose Se treatments (≥12 mg kg−1) hindered plant growth. Optimal Se dose (6 mg kg−1) stimulated plant growth by reducing MDA content and improving photosynthetic capability. However, excess Se (24 mg kg−1) increased MDA content by 28%, decreased net photosynthetic rate and carboxylation efficiency by 34% and 39%, respectively. The Se concentration in the roots, stems, and leaves of the tobacco plants significantly increased with increasing Se application. A linear correlation (R = 0.95, P < 0.01) was observed between Se level and tobacco plant tissue Se concentration. This correlation indicated that the tobacco plant tissues were not saturated within the concentration range tested. The pattern of total Se concentration in the tobacco plant tissues followed the order root > leaf > stem. The Se concentration in the roots was 3.17 and 7.57 times higher than that in the leaves and stems, respectively, after treatment with 24 mg kg−1 Se. In conclusion, the present study suggested that optimal Se dose (6 mg kg−1) improved the plant growth mainly by enhancing photosynthesis, stomatal conductance, carboxylation efficiency and Rubisco content in the flue-cured tobacco leaves. However, the inhibition of excess Se on tobacco growth might be due to high accumulation of Se in roots and the damage of photosynthesis in leaves.
Źródło:
Acta Societatis Botanicorum Poloniae; 2015, 84, 1
0001-6977
2083-9480
Pojawia się w:
Acta Societatis Botanicorum Poloniae
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Finite Element Modeling for the Uni-Axial Tensile Behaviour of Metallic Warp-Knitted Fabric
Zastosowanie metody elementów skończonych (FEM) do przewidywania jednoosiowego rozciągania dzianin metalicznych
Autorzy:
Xu, H.-Y.
Jiang, J.-H.
Chen, N.-L.
Lin, F.-B.
Shao, H.-Q.
Powiązania:
https://bibliotekanauki.pl/articles/231781.pdf
Data publikacji:
2018
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
warp-knitted fabric
finite element analysis
tensile behavior
metallic
TexGen
dzianina osnowowa
analiza elementów skończonych
proces rozciągania
dzianina metaliczna
Opis:
The finite element analysis method (FEM), for its advantages of lower time and economic costing in predicting the mechanical properties of fabrics, was applied to warp-knitted fabrics. In this paper, two bar warp-knitted fabric knitted with wires was used as reflecting mesh antennas. Firstly the loop unit of the metallic warp-knitted fabric was simulated in 3-D by TexGen software. Secondly the 3-D loop unit model was inputted into ABAQUS software to form a model of the metallic warp-knitted fabric sheet for uni-axial tension analysis. Thirdly numerical results were obtained after setting the parameters in ABAQUS. Finally numerical results were verified by uni-axial tensile experiments on the metallic warp-knitted fabric. The results showed that the simulation was in good agreement with the experimental tensile process, where the transfer of yarns between loops when in low fabric elongation and in yarn elongation when in high fabric elongation were simulated by FEM of warp-knitted fabric in the tensile process. Also the same trend of tensile force was found in experiment and FEM results. Therefore it can be concluded that FEM can be used to predict the mechanical properties of warp-knitted fabric with a complex structure.
Do przewidywaniu mechanicznych właściwości dzianin metalicznych zastosowano metodę elementów skończonych (FEM). Symulacji 3D dzianin dokonano przy użyciu dwóch rodzajów oprogramowania: TexGen i ABAQU. Wyniki symulacji zweryfikowano eksperymentalnie. Stwierdzono, że symulacja charakteryzowała się zgodnością z eksperymentalnie przeprowadzonym procesem rozciągania. Na podstawie wyników stwierdzono, że metoda elementów skończonych (FEM) może być z powodzeniem wykorzystywana do przewidywania mechanicznych właściwości dzianin o złożonej strukturze.
Źródło:
Fibres & Textiles in Eastern Europe; 2018, 2 (128); 49-54
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies