Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Sahbaz, O." wg kryterium: Autor


Wyświetlanie 1-6 z 6
Tytuł:
Determining optimal conditions for lignite flotation by design of experiments and the halbich upgrading curve
Autorzy:
Sahbaz, O.
Powiązania:
https://bibliotekanauki.pl/articles/109920.pdf
Data publikacji:
2013
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
low rank coal
flotation
design of experiment
upgrading curves
Opis:
In this study conditions for flotation of low rank coal (lignite of Tuncbilek, Turkey) were investigated in detail. The experiments were performed using the 3-variable 2-level (23) full factorial experimental design with four base point replicates, and the results were analyzed by the regression model, Fischer test (F-test) and Halbich’s upgrading curve for the responses of ash content (or combustible matter grade) and the combustible matter recovery. The results obtained from the analysis indicated that while every factor considerably affected the combustible matter recovery, both collector (kerosene) and frother (AF65) significantly influenced the ash contents of the carbonaceous matter products. The only effective mutual interaction influencing recovery was caused by the kerosene-aeration interaction, while the interaction of kerosene-aeration and kerosene-AF65 and interactions of all factors (kerosene-AF65-aeration) were significant for the ash content of the products. Basing on the grade–recovery Halbich upgrading curve, regression model and a criterion for optimum of flotation results, it was found that a coal product with combustible matter grade of 91.09% and 71% combustible matter recovery can be obtained provided that it is processed at the higher level of kerosene (3 kg/Mg), higher level of frother AF65 (40 ppm) and lower aeration rate level of (0.16 cm/s).
Źródło:
Physicochemical Problems of Mineral Processing; 2013, 49, 2; 535-546
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Recycling of colemanite tailings using the Jameson flotation technology
Autorzy:
Ucar, A.
Sahbaz, O.
Kerenciler, S.
Oteyaka, B.
Powiązania:
https://bibliotekanauki.pl/articles/110375.pdf
Data publikacji:
2014
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
colemanite tailing
flotation
Jameson cell
Opis:
In this study, beneficiation of colemanite minerals from tailings of the Emet Boron Processing Plant using a laboratory scale Jameson flotation cell was investigated in detail. Effect of some working parameters of the Jameson cell such as jet length, plunging depth of downcomer, and bias factor was studied for the flotation performance of colemanite. The results showed that all parameters showed a significant effect on colemanite flotation using the Jameson cell which was the first time used in boron flotation with a negative bias factor. The results also indicated that a high recovery could be obtained with a worthy grade values by the negative bias factor. According to the results obtained at the bias factor of -0.3, jet length of 3 cm, and plunging depth of 20 cm, B2O3 content of the sample increased to approximately 46% from 36.8% with a recovery of 98.47%.
Źródło:
Physicochemical Problems of Mineral Processing; 2014, 50, 2; 645-655
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
In search of an efficient frother for pre-flotation of carbonaceous shale from the kupferschiefer stratiform copper ore
Autorzy:
Kowalczuk, P. B.
Buluc, B.
Sahbaz, O.
Drzymala, J.
Powiązania:
https://bibliotekanauki.pl/articles/109705.pdf
Data publikacji:
2014
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
frother
pre-flotation
copper ore
shale
Opis:
This papers shows that frothers such as aliphatic alcohols (CnH2n+1OH), poly(propylene glycols) (HO(C3H6O)mH), poly(propylene glycol) alkyl ethers (CnH2n+1O(C3H6O)mH) and poly(ethylene glycol) alkyl ethers (CnH2n+1O(C2H4O)mH), can be used for collectorless flotation of a sample of carbonaceous copper shale manually separated from the Kupferschiefer stratiform copper ore. It was shown that flotation is influenced by the type and dose of frothers. The best flotation results were obtained with tri(propylene glycol) butyl ether C4P3, tri(propylene glycol) propyl ether C3P3 and tri(propylene glycol) P3. For these frothers, the yield vs. frother dose relationship was in the form of convex curves indicating that carbonaceous copper shale can float at relatively low dosages of the frother. It means that these frothers can be used for pre-flotation of carbonaceous matter from the investigated copper ore. Other frothers formed concave yield–frother dose relationships and were less effective.
Źródło:
Physicochemical Problems of Mineral Processing; 2014, 50, 2; 835-840
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison of Jameson cell and jet diffuser flotation column
Autorzy:
Bilir, K.
Ucar, A.
Sahbaz, O.
Gursoy, H.
Oteyaka, B.
Powiązania:
https://bibliotekanauki.pl/articles/109686.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
jet diffuser flotation column
flotation
Jameson Cell
talc
Opis:
A Jet Diffuser Flotation Column (JDFC) is a newly designed flotation device which resembles the Jameson cell (JFC) in terms of operational principles, but it has an important difference regarding to the structural characteristics in the downcomer. The main difference of JDFC is the diffuser type of downcomer which has been designed using the hydrodynamic consideration and fluid mechanics principles. The aim of the design was to increase the device efficiency for coarse particle flotation. Therefore, the turbulence occurring at the end of the downcomer was reduced, and the detachment probability of the coarse particle decreased. In addition, a homogenous and stable foam zone in the cell was obtained. According to the experimental results carried out in a pilot scale showed that not only higher flotation performance in comparison to the Jameson cell was obtained specifically for the coarse particles but also the quiescent froth layer was acquired under the given conditions. In these experiments, a vertical pipe of JDFC having an inlet diameter of 60 mm and outlet diameters of 115, 125 and 135 mm was used with the separation tank with the diameter of 390 mm. By using the data, the pilot scale JDFC with the 4100 mm vertical pipe integrated with the separation tank was produced, and the flotation tests were carried out by using a talc ore. Finally, the talc recovery of 90% was obtained using the JDFC for the particle size of 350 μm.
Źródło:
Physicochemical Problems of Mineral Processing; 2018, 54, 1; 174-181
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Water contact angle on corresponding surfaces of freshly fractured fluorite, calcite and mica
Autorzy:
Kowalczuk, P. B.
Akkaya, C.
Ergun, M.
Janicki, M.
Sahbaz, O.
Drzymala, J.
Powiązania:
https://bibliotekanauki.pl/articles/110595.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
contact angle
surface properties
cleaving plane
surface composition
corresponding halves
fluorite
calcite
mica
Opis:
Advancing and receding contact angles of water with corresponding surfaces of freshly fractured calcite, fluorite and mica were measured. The corresponding surfaces were obtained by mechanical splitting of a small lump of each mineral into two pieces. Theoretical considerations revealed that depending on the mineral cleaving plane, surfaces created by splitting into halves can be either identical or entirely different as far as their surface chemical composition is concerned. It was experimentally established that receding and advancing contact angles measured on the corresponding surfaces of fluorite, calcite and mica were identical for the sessile drop method. When the contact angle was measured by the captive bubble approach, there were small differences in the contact angles measured on the corresponding surfaces of fluorite. It was most probably due to surface irregularities and roughness, and therefore different times needed to rupture the liquid film between the bubble and solid surface.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 1; 192-201
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
ZnO nanoparticles bonded to SiO₂ filler as a curing accelerator in cold vulcanizing adhesives
Autorzy:
Acikgoz, C.
Sahbaz, D.
Kockar, O.
Powiązania:
https://bibliotekanauki.pl/articles/1055164.pdf
Data publikacji:
2017-01
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.20.-n
Opis:
The aim of this study is to investigate the interaction of ZnO/SiO₂ particles between the chloroprene rubber and its effect on the cure characteristics and mechanical properties of the cold vulcanizing adhesives. Curing efficiency and mechanical properties of ZnO/SiO₂ filled adhesives were compared with SiO₂ filled adhesives. ZnO nanoparticles were bounded to SiO₂ spherical nanoparticles by hydrolysis and condensation process. The morphology and elemental content of ZnO/SiO₂ particles were investigated by scanning electron microscopy and energy dispersive spectroscopy. The ZnO/SiO₂ particles were then blended with chloroprene rubber as accelerator during the vulcanization process. Cure characteristics, which are scorch time (t_{s2}), cure time (t_{c90}), maximum torque (M_{H}) and minimum torque (M_{L}) of the rubber compounds were determined at 190°C with a moving die rheometer. The fabric conveyor belt was used for measuring adhesive strength of the adhesives. The fabric conveyor belt was used for measuring adhesive strength of the adhesives. Application of the cold vulcanizing adhesives to the fabric conveyor belt was carried out at three different times (4, 8, and 24 h), 25°C temperature and 0.3 kg/cm² pressure. The results showed that ZnO/SiO₂ particles provided a higher adhesive strength than silica in the 4, 8, and 24 h of adhesion. ZnO/SiO₂ filled rubber blends gained superior vulcanization characteristics by the increasing cure rate index with the reducing cure time and scorch time. It has been concluded that ZnO/SiO₂ particles can be used as a new curing accelerator and simultaneously reinforcing filler.
Źródło:
Acta Physica Polonica A; 2017, 131, 1; 200-203
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-6 z 6

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies