Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Michalczyk, K." wg kryterium: Autor


Tytuł:
Analysis of lateral vibrations of the axially loaded helical spring
Autorzy:
Michalczyk, K.
Powiązania:
https://bibliotekanauki.pl/articles/279466.pdf
Data publikacji:
2015
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
helical spring vibrations
axially loaded spring
coil spring
Timoshenko equivalent beam
Opis:
It is shown in this paper that the proposed concept by Krużelecki and Życzkowski (1990) of the equivalent rod can be applied in calculations of natural lateral vibrations of springs and that the obtained results will be nearer FEM results than the standard model based on the Timoshenko equivalent beam. The model, created on this base, allows one to calculate natural frequencies of the clamped-clamped spring. It is also shown that models based on the equivalent beam concept, which are easier to apply than the models treating the spring as the spatially curved rod, have only a slightly smaller accuracy. It is also indicated that in the most common practice making of manufacturing end coils of springs, the natural frequencies differ significantly from the frequencies calculated by means of all tested methods. The performed simulations show that differences between the first and the second as well as the third and the fourth natural frequency of the spring are small and, therefore, the axially symmetrical equivalent beam model can be used without a large error. The diagram allowing one to determine whether the desired frequencies are lower or higher than the cut-off frequency is developed for the presented model.
Źródło:
Journal of Theoretical and Applied Mechanics; 2015, 53, 3; 745-755
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Natural transverse vibrations of helical springs in sections covered with elastic coatings
Autorzy:
Michalczyk, K.
Powiązania:
https://bibliotekanauki.pl/articles/200869.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
helical spring vibrations
natural frequencies
free transverse vibrations
axially loaded spring
spring with coatings
drgania sprężyny śrubowej
częstotliwości naturalne
wolne wibracje
Opis:
It has been demonstrated in previous studies that local elastomer coatings covering the end coils of helical springs can efficiently reduce the amplitudes of circum-resonant vibrations in such springs. The analysis of the influence that elastic coatings have on the frequencies and modes of natural transverse vibrations of springs is presented in this paper. The concept of the equivalent beam of the Timoshenko type is utilized in calculations of the frequencies and modes of transverse vibrations. The model developed allows users to determine the frequencies and modes of symmetric as well as antisymmetric vibrations of axially loaded springs with elastic coatings of arbitrary length. A comparison of the results obtained using FEM analysis, in which the model represented the actual spring geometry, with the results obtained by means of the presented model indicates its high accuracy.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2017, 65, 6; 949-959
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of the elastomeric coating on parameters of steady state vibrations of coil springs in the resonance and outside it
Autorzy:
Michalczyk, K.
Powiązania:
https://bibliotekanauki.pl/articles/280427.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
helical springs vibrations
coil springs
dynamic stresses
damping
Opis:
The computational model of steady state vibrations of the coil spring covered with an elastomeric layer under resonance conditions and outside them is presented in the paper. It enables one to assess the reduction effectiveness of dynamic stresses in function of the material and geometrical parameters of the applied coating. The considerations are supplemented with the numerical examples.
Źródło:
Journal of Theoretical and Applied Mechanics; 2014, 52, 2; 507-518
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical modelling of metal-elastomer spring nonlinear response for low-rate deformations
Autorzy:
Sikora, W.
Michalczyk, K.
Machniewicz, T.
Powiązania:
https://bibliotekanauki.pl/articles/386307.pdf
Data publikacji:
2018
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
bergström-boyce model
neidhart’s spring
metal-elastomer spring
FEM
SBR rubber
nonlinear spring
Opis:
Advanced knowledge of mechanical characteristics of metal-elastomer springs is useful in their design process and selection. It can also be used in simulating dynamics of machine where such elements are utilized. Therefore this paper presents a procedure for preparing and executing FEM modelling of a single metal-elastomer spring, also called Neidhart’s spring, for low-rate deformations. Elastomer elements were made of SBR rubber of two hardness values: 50°Sh and 70°Sh. For the description of material behaviour the Bergström-Boyce model has been used.
Źródło:
Acta Mechanica et Automatica; 2018, 12, 1; 31-37
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analiza wytrzymałościowa generatora dla tłumika MR w samozasilającym się układzie redukcji drgań
Structural analysis of a generator supplying a linear magnetorheological damper in a selfpowered vibration reduction system
Autorzy:
Michalczyk, K.
Sapiński, B.
Szydło, B.
Powiązania:
https://bibliotekanauki.pl/articles/386673.pdf
Data publikacji:
2011
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
analiza wytrzymałościowa
redukcja drgań
generator
structural analysis
reduction vibration
Opis:
W pracy przedstawiono analizę wytężenia generatora elektromagnetycznego zasilającego liniowy tłumik magnetoreologiczny (MR). Generator ten współpracuje z tłumikiem MR w układzie równoległym. Elementem generatora, który podlega największym obciążeniom jest jego korpus, gdyż jest on związany ze źródłem drgań. W pracy zaprezentowano wyniki symulacji numerycznych oraz obliczeń wskazujących miejsca najbardziej wytężone. Podano również wskazówki pozwalające na obniżenie poziomu naprężeń w miejscach ich koncentracji.
In this paper the construction and the structural analysis of electromagnetic generator supplying a linear magnetorheological damper has been presented. The generator operates with an MR dam- per in parallel arrangement. The most efforted element of the generator is its body, which is mounted directly on the plate connected with electromagnetic vibration generator. The results of numerical simulations and calculations indicating the most efforted parts of the generator’s body has been shown. Some hints about improve- ments in the generator’s construction has been also added.
Źródło:
Acta Mechanica et Automatica; 2011, 5, 3; 91-98
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A study of the preload force in metal-elastomer torsion springs
Autorzy:
Sikora, W.
Michalczyk, K.
Machniewicz, T.
Powiązania:
https://bibliotekanauki.pl/articles/386440.pdf
Data publikacji:
2016
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
hyperelastic materials
neidhart spring
metal-elastomer spring
FEM
finite element method
materiał hiperelastyczny
elastomer
metoda elementów skończonych
MES
Opis:
Neidhart type suspension units composed of metal-elastomer torsion springs can be a good alternative to steel helical springs in applications such as vibration absorbers or vehicle suspension systems. Assembling this type of spring requires initial preload of the elastomeric working elements, which determines their operating properties.The results of experimental tests and numerical simulations concerning the preload of elastomeric working elements in Neidhart type suspension units are presented in the paper. The performed research made it possible to propose a new calculation model for determining the preload force value acting on the elastomeric cylindrical elements applied in this type of suspension unit. The results obtained using the proposed model exhibit good convergence with FEM simulation results within the range of the tested geometrical and material properties.
Źródło:
Acta Mechanica et Automatica; 2016, 10, 4; 300-305
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical simulations by Godunov-type schemes of air-pollutant dynamics
Autorzy:
Murawski, K.
Michalczyk, J. K.
Powiązania:
https://bibliotekanauki.pl/articles/1955805.pdf
Data publikacji:
2001
Wydawca:
Politechnika Gdańska
Tematy:
numerical simulation
numerical discretization
hydrodynamic equations
distrubution of air-pollutants
Opis:
In this paper several aspects associated with numerical simulations of hyperbolic equations are discussed. This presentation covers a range of modern shock-capturing schemes which are based on Godunov-type techniques. These schemes are well suited for strong shocks and other discontinuities, without generating spurious oscillations in the flow variables. An example of a performance of such schemes is provided to simulate the spatial distribution of air-pollutants which are emitted from a chimney. The simulations are performed in the framework of two-dimensional hydrodynamics, with a use of the CLAWPACK code (R.J.LeVeque, CLAWPACK User Notes, Applied Mathematics,Univ. of Washington, Seattle, 1997a). The model reproduces several features of the distribution, including occurrence of vortices and plumes above the chimney.
Źródło:
TASK Quarterly. Scientific Bulletin of Academic Computer Centre in Gdansk; 2001, 5, 2; 207-228
1428-6394
Pojawia się w:
TASK Quarterly. Scientific Bulletin of Academic Computer Centre in Gdansk
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical simulations of air-pollutants in windy atmosphere
Autorzy:
Michalczyk, J. K.
Murawski, K.
Powiązania:
https://bibliotekanauki.pl/articles/1962998.pdf
Data publikacji:
2002
Wydawca:
Politechnika Gdańska
Tematy:
environmental protection engineering
transport of air-pollutants
plume structure
turbulence
Opis:
Spreading of gaseous pollutants in windy atmosphere is considered by means of numerical simulations of two-dimensional hydrodynamic equations. The parametric studies, which are performed for various magnitudes of a horizontal wind speed, reveal a plume development and a generation of vortices which occur as a result of Kelvin-Helmholtz instabilities. Mass density profiles exhibit high level of spatial and temporal variability. A spectral analysis of these profiles provides variable circular frequency and a wave number.
Źródło:
TASK Quarterly. Scientific Bulletin of Academic Computer Centre in Gdansk; 2002, 6, 2; 309-321
1428-6394
Pojawia się w:
TASK Quarterly. Scientific Bulletin of Academic Computer Centre in Gdansk
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Development and Modelling of the Method of Mandrelless Small-Radius Tube Bending
Opracowanie i modelowanie sposobu beztrzpieniowego gięcia rur na małych promieniach
Autorzy:
Michalczyk, J.
Wojsyk, K.
Powiązania:
https://bibliotekanauki.pl/articles/356395.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
mandrelless tube bending
small bending radii
beztrzpieniowe gięcie rur
małe promienie gięcia
Opis:
The paper reports the results of research aimed at creating theoretical grounds for a new method of mandrelless small-radius tube bending (1.5DrRg<2.5Dr, where Dr - tube diameter, Rg - bending radius). As the result of applying such a methodology it is possible to carry out the bending process (with an angle of up to 180°) and obtain an ovalization and wall thinning in the bending area, which are much smaller than those in currently manufactured products. The currently used bending methods and bending equipment are able to achieve a minimum bending radius not less than three times the tube outer diameter. The research hypothesis has assumed the existence of tube bending methods that are more efficient that those known so far. Than methods do not rely on circular bending contours, but instead they may use other shaping die contours which has not been explored yet. Circular benders used in practice fail in that they do not yield the expected results on small radii and do not control the material flow (do not ensure its correct behaviour) in the bending zone. The literature review has shown that there are currently no theoretical studies, numerical analyses and experimental verifications related to the processes of mandrelless tube bending on small radii, i.e. for 1.5D≤R≥2.5D, where: (R - bending radius, D - tube outer diameter) up to an angle of 180°. Due to the lack of studies on this subject, in their approach to the numerical modelling of the problem, the authors of the paper were guided by their own experience in this field and made every effort to make the numerical model reflect the actual process as accurately as possible. They were only aided by the general knowledge accumulated in the literature on numerical modelling. To sum up, the purpose of the publication is to demonstrate that the change in the die recess towards a shape resembling an ellipse results in a change in the characteristics of metal flow (movement) along the tube perimeter and in a change in the stress characteristics and, as a consequence, a change in the tube cross-section in the bending zone. The research discussed in this paper seeks to establish the correct flow of material in the tube cross-section in the bending zone by determining the most efficient bender recess shape and friction surface forming, which will eliminate the excessive ovalization and upper wall thinning. The expected effect of implementing this bending technology will be increasing the flow capacity in energy systems, which will directly translate into a reduction of atmospheric CO emissions due to the lower energy consumption. In addition, the paper has presented the concepts of tools intended for the experimental verification of tube bending process.
W pracy przedstawiono wyniki badań polegających na stworzeniu podbudowy teoretycznej do nowej metody beztrzpieniowego gięcia rur na małych promieniach (1.5DrRg<2.5Dr, gdzie Dr – Średnica rury, Rg – promień gięcia). W wyniku zastosowania takiej metodyki można przeprowadzić proces gięcia (o kącie do 180°) i otrzymać w obszarze gięcia owalizację i pocienienie ścianki znacznie mniejsze niż w otrzymywanych obecnie wyrobach. Obecnie stosowane metody gięcia oraz urządzenia gnące pozwalają osiągnąć minimalny promień gięcia nie mniejszy niż trzykrotność średnicy zewnętrznej rury. Hipoteza badawcza zakładała, że istnieją efektywniejsze od dotychczas znanych sposoby gięcia rur. Sposoby te nie są oparte na kołowych profilach gnących, lecz mogą uwzględniać inne niezbadane dotychczas profile form kształtujących. Stosowane w praktyce kołowe wykroje zawodzą w ten sposób, że, nie dają efektów na małych promieniach, nie sterują (nie umożliwiają właściwego przepływu materiału w strefie gięcia). Analiza literatury wykazała, iż nie istnieją obecnie żadne opracowania teoretyczne, analizy numeryczne oraz weryfikacje doświadczalne dotyczące procesów beztrzpieniowego gięcia rur na małych promieniach tj. dla 1.5D≤R≥2.5D, gdzie: (R – promień gięcia, D – średnica zewnętrzna rury) do kąta 180°. Autorzy pracy w podejściu do modelowania numerycznego zagadnienia z uwagi na brak opracowań w tym zakresie (gięcie małych promieni) kierowali się własnym doświadczeniem w tej dziedzinie i dokonali wszelkich starań, aby założony model numeryczny jak najbardziej uprawdopodobnić z rzeczywistym procesem. Wspomagali się jedynie ogólną wiedzą zgromadzoną w literaturze nt. modelowania numerycznego. Reasumując celem publikacji jest wykazanie, iż zmiana kształtu wybrania wzornika w kierunku kształtu zbliżonego do elipsy skutkuje zmianą charakterystyki płynięcia (przemieszczania się) metalu po obwodzie rury i zmianą charakterystyki naprężeń a w konsekwencji zmianę kształtu przekroju rury w strefie gięcia. Prezentowane w pracy badania polegają na poszukiwaniu właściwego przepływu materiału w przekroju rury w strefie gięcia poprzez ustalenie najbardziej efektywnego kształtu wybrania w wykroju oraz kształtowaniu powierzchni tarcia, przez co zostaną wyeliminowane: nadmierna owalizacja i pocienienie ścianki górnej. Przewidywanym efektem zastosowania tej technologii gięcia będzie zwiększenie wydajności przepływu w instalacjach energetycznych, co ma związek bezpośredni związek ze spadkiem emisji CO do atmosfery w wyniku mniejszego zużycia energii. Ponadto w pracy przedstawiono koncepcje narzędzi do doświadczalnej weryfikacji procesu gięcia rur.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 4; 2797-2804
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wybrane zagadnienia projektowania lekkich samolotów sportowych w aspekcie światowych przepisów lotniczych
Selected aspects in designing light sport aircraft in the context of the global aviation regulations
Autorzy:
Szafran, K.
Michalczyk, M.
Powiązania:
https://bibliotekanauki.pl/articles/213271.pdf
Data publikacji:
2016
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Lotnictwa
Tematy:
przepisy lotnicze
certyfikacja
bezpieczeństwo lotu
aviation regulations
certification
flight safety
Opis:
W artykule przedstawiono wybrane wymagania stawiane małym statkom powietrznym, które są konieczne do uzyskania odpowiedniego certyfikatu. Przedstawiono najważniejsze różnice między wymaganiami CS-LSA, CS-YLA oraz CS-23. Porównano rozbieżności pomiędzy europejskimi i amerykańskimi przepisami dotyczącymi budowy cywilnych małych statków powietrznych. Przytoczono także niektóre przepisy i zalecenia ICAO dotyczące bezpieczeństwa w lotnictwie z ukierunkowaniem na projektowanie i eksploatację samolotów. W zakończeniu autorzy wysunęli wniosek globalnego ujednolicenia przepisów, co niewątpliwie będzie realizowane w przyszłości.
Selected requirements for small aircraft, which are necessary to obtain the relevant certificate are presented in this paper. The most important differences between the requirements of CS-LSA, CS-YLA and CS-23 are presented. Differences between European and American regulations for the construction of small civilian aircraft are compared. Also some of the provisions and recommendations of the IC AO on aviation security with a focus on the design and operation of airplanes are quoted. In the conclusions, the authors put forward a proposal of global standardization of regulations, winch undoubtedly will be implemented in the future.
Źródło:
Prace Instytutu Lotnictwa; 2016, 2 (243); 142-153
0509-6669
2300-5408
Pojawia się w:
Prace Instytutu Lotnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies