Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Kim, K. I." wg kryterium: Autor


Wyświetlanie 1-13 z 13
Tytuł:
Growth of NdBa$\text{}_{2}$Cu$\text{}_{3}$O$\text{}_{7-δ}$ Superconducting Thin Films on SrTiO$\text{}_{3}$(100) and LaSrGaO$\text{}_{4}$(100) Substrates
Autorzy:
Park, J.-C.
Ha, D. H.
Kim, I.-S.
Park, Y.K.
Powiązania:
https://bibliotekanauki.pl/articles/1964239.pdf
Data publikacji:
1997-07
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
74.76.Bz
Opis:
NdBa$\text{}_{2}$Cu$\text{}_{3}$O$\text{}_{7-δ}$ superconducting thin films were grown on SrTiO$\text{}_{3}$(100) and LaSrGaO$\text{}_{4}$(100) substrates by off-axis rf sputtering and pulsed laser deposition. The effects of several deposition parameters, e.g. gas pressure, substrate temperature and energy density were studied. Thin films grown by off-axis rf sputtering were highly c-axis oriented, but those by pulsed laser deposition were predominantly a-axis oriented under our deposition conditions. However, the c-axis oriented portion for the films grown by pulsed laser deposition was increased by increasing the temperature above 800°C. T$\text{}_{c(zero)}$ was 87 K and 83 K for the c- and a-axis oriented films respectively. The critical current density of c-axis oriented films was 10$\text{}^{6}$-10$\text{}^{7}$ A/cm$\text{}^{2}$ below 60 K.
Źródło:
Acta Physica Polonica A; 1997, 92, 1; 105-114
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of Antireflection Structures as a Protective Layer of Solar Cells with Nanoporous Silica Films and Nanoimprinted Moth-Eye Structure
Autorzy:
Kim, K.
Han, J.
Jang, J.
Choi, C.
Choi, S.
Kim, C.
Kye, H.
Cheong, I.
Powiązania:
https://bibliotekanauki.pl/articles/1492625.pdf
Data publikacji:
2011-12
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
61.46.-w
68.37.-d
68.55.-a
78.20.-e
Opis:
The antireflection structures are fabricated by sol-gel process as a protective layer of solar cells and by hot embossing process with anodized aluminum oxide membrane template on polycarbonate film. The optical properties and morphology of the antireflection structures are analyzed by UV-visible spectroscopy and field emission scanning electron microscopy, respectively. The total conversion efficiency of a polycrystalline Si solar cell module with the protective layer, sol-gel-derived nanoporous antireflection structure, is increased by 2.6% and 5.7% for one-side antireflection coated prismatic matt glass and both-side antireflection coated prismatic matt glass, respectively.
Źródło:
Acta Physica Polonica A; 2011, 120, 6A; A-047-A-049
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Low-velocity impact characteristics of composite plates with shape memory alloy wires
Niskoprędkościowe charakterystyki uderzeniowe płyt kompozytowych zawierających włókna ze stopów z pamięcią kształtu
Autorzy:
Rim, M.-S.
Kim, E.-H.
Lee, I.
Choi, I.-H.
Ahn, S.-M.
Koo, K.-N.
Bae, J.-S.
Roh, J.-H.
Powiązania:
https://bibliotekanauki.pl/articles/279293.pdf
Data publikacji:
2011
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
shape memory alloy
SMAHC
composite
low-velocity impact
impact resistance
Opis:
To investigate impact characteristics of shape memory alloy hybrid com- posites (SMAHC), several experiments were performed. Tensile tests of shape memory alloy (SMA) wires were carried out to investigate thermomechanical properties, and low-velocity impact tests of SMAHC plates and conventional composite plates without SMAs at the critical energy level. low-velocity impact tests of several types of composite plates, including composite plates with embedded SMAs/Fe/Al wires and conventional composite plates, were also done. Results of these experiments show that embedding SMAs in a composite plate can improve the impact resistance. Lastly, low-velocity impact tests of SMAHC plates with SMA wires embedded at different positions through the thickness were performed in an effort to improve the impact resistance. Embedding SMA wires at a lower position in the composite plates was the most effective for improving the impact resistance.
Do analizy charakterystyk uderzeniowych hybrydowych kompozytów SMAHC zwierających włókna SMA ze stopów wykazujących efekt pamięci kształtu przeprowadzono szereg badań eksperymentalnych. Przeprowadzono próby na rozciąganie włókien SMA w celu zbadania ich właściwości termomechanicznych oraz niskoprędkościowe testy uderzeniowe płyt SMAHC oraz konwencjonalnych płyt laminowanych przy energii krytycznej. Wykonano także testy dla płyt kompozytowych zawierających włókna SMA/Fe/Al. Rezultaty doświadczeń pokazały, że wbudowanie w strukturę laminatu włókien SMA może zwiększyć odporność kompozytu na obciążenie uderzeniowe. Opisano również badania eksperymentalne płyt SMAHC z włóknami SMA wbudowanymi na różnej głębokości. Wykazano, że najlepsze parametry posiadają kompozyty z włóknami umieszczonymi możliwie daleko od uderzanej powierzchni.
Źródło:
Journal of Theoretical and Applied Mechanics; 2011, 49, 3; 841-857
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Maritime traffic characteristics in waterway with time variant CPA
Autorzy:
Jeong, J.S.
Park, G.K.
Kim, K. I.
Powiązania:
https://bibliotekanauki.pl/articles/320550.pdf
Data publikacji:
2013
Wydawca:
Polskie Forum Nawigacyjne
Tematy:
maritime traffic management
operation rate
risk assessment
collision
CPA
TCPA
Opis:
This paper aims at evaluating the collision risk between the encountering vessels under time- -variant CPA situations and then assessing the maritime traffic characteristics. Radar and AIS data are collected from Mokpo VTS in Korea. All crossing vessels that are navigating within CPA 1 miles of Mokpo-Gu waterway are analyzed. The maritime traffic characteristics is analyzed by surveying the distribution of CPA as a function of TCPA. To make it clear, the traffic operating rate in the Mokpo waterway is also computed. The averages of CPA and TCPA were observed until the encountered vessels pass safety each other after they come in a certain ship domain. As a consequence, the distribution of CPA as a function of TCPA gives a useful information to evaluate the maritime traffic safety.
Celem artykułu jest ocena ryzyka kolizji statków w funkcji zmiany wartości czasu do kolizji, a na tej podstawie oszacowanie charakterystyk determinujących ruch morski. Dane z radarów oraz systemu AIS zostały zarejestrowane w systemie VTS Mokpo w Korei. Przeanalizowano wszystkie przypadki przecinania się tras statków na podejściu do Mokpo-Gu w przypadku, gdy odległość minimalna (CPA) była mniejsza niż jedna mila morska. Charakterystyka ruchu morskiego opisana została poprzez wyznaczenie rozkładu wartości największego zbliżenia statków jako funkcji czasu do nadmiernego zbliżenia (TCPA). Dla pełnej jasności obliczono również współczynnik przepustowości drogi wodnej Mokpo. Opisano średnie wartości odległości największego zbliżenia oraz czasu do wystąpienia CPA bez względu na przekroczenia granic domeny obserwowanych statków. W konsekwencji wyznaczono rozkład wartości CPA jako funkcję TCPA, co okazuje się użyteczne dla oceny bezpieczeństwa ruchu morskiego.
Źródło:
Annual of Navigation; 2013, 20; 49-58
1640-8632
Pojawia się w:
Annual of Navigation
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Study On The Metal Carbide Composite Diffusion Bonding For Mechanical Seal
Badanie łączenia dyfuzyjnego kompozytu metal węglik na mechaniczne uszczelnienie
Autorzy:
Kim, D.-K.
Shon, I.-J.
Song, J.
Ryu, W.-J.
Shin, H.-Ch.
Kwon, E.-Y.
Shin, H.
Kang, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/356399.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
diffusion bonding
nanostructures
mechanical seal
hard metal
mechanical properties
łączenie
nanostruktura
uszczelnienie mechaniczne
twardy metal
właściwości mechaniczne
Opis:
Mechanical Seal use highly efficient alternative water having a great quantity of an aqueous solution and has an advantage no corrosion brine. Metal Carbide composites have been investigated as potential materials for high temperature structural applications and for application in the processing industry. The existing Mechanical seal material is a highly expensive carbide alloy, and it is difficult to take a price advantage. Therefore the study of replacing body area with inexpensive steel material excluding O-ring and contact area which demands high characteristics is needed. The development of WC-Ni base carbide alloy optimal bonding composition technique was accomplished in this study. To check out the influence of bonding temperature and time, bonding characteristics of sintering temperature was experimented. The bonding statuses of this test specimen were excellent. The hardness of specimen and bonding rate were measured using ultrasound equipment. In this work, Powder of WC (involved VC, Cr), Co and Mo2C mixed by attrition milling for 24hours. Nanostructured WC-27.6wt.%Ni-1.5wt.%Si-0.11wt.%VC-1.1wt.%B4C composite were fabricated at 1190°C by high temperature vacuum furnace. To check out the influence of bonding temperature and time, bonding characteristics of sintering temperature was experimented. Its relative density was about 99.7%. The mechanical properties (hardness and fracture toughness) were 87.2 HRA and 4.2 M·Pam1/2, respectively. The bonding status of this test specimen was excellent and the thickness of bonding layer was 20 ~30§ at 1050 and 1060°C bonding temperature.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1479-1483
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics Of The Porous Body Sintered By Nano-Sized Fe-Cr-Al Alloy Powder
Charakterystyka porowatego korpusu spiekanego z nanometrycznego proszku stopu Fe-Cr-Al
Autorzy:
Lee, S.-I.
Lee, S.-H.
Gu, B.-U.
Lee, D.-W.
Kim, B.-K.
Powiązania:
https://bibliotekanauki.pl/articles/356635.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Fe-Cr-Al powder
metallic sponges
sintering temperature
oxidation resistance
proszek Fe-Cr-Al
proszek nanometryczny
temperatura spiekania
odporność na utlenianie
Opis:
Porous metal with uniform honeycomb structure was successfully produced by sintering using Fe-Cr-Al nano powder, which was prepared by the pulsed wire evaporation (PWE) in ethanol. Its process consisted of the several steps; 1) coating on the surface of polyurethane sponge with the liquid droplets generated from the ethanol-based slurry where the Fe-Cr-Al nano powders were uniformly dispersed, 2) heat treatment of debinding to remove the polyurethane sponge and 3) sintering of the porous green body formed by Fe-Cr-Al nano powders. The strut thickness of porous Fe-Cr-Al was increased by the increase of spraying times in ESP step. Also, The shrinkages and the oxidation resistance of the sintered porous body was increased with increase of sintering temperature. The optimal sintering temperature was shown to 1450°C in views to maximize the oxidation resistance and sinterability.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1275-1279
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characterization Of The Graded Microstructure In Powder Sintered Porous Titanium
Charakterystyka gradientowej mikrostruktury porowatego tytanu spiekanego z proszku
Autorzy:
Oak, J.-J.
Bang, J. I.
Bae, K.-C.
Kim, Y. H.
Lee, Y. C.
Chun, H. H.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/356239.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
titanium
powder metallurgy
porous structure
sintering
biomaterial
tytan
metalurgia proszków
struktura porowata
spiekanie
biomateriał
Opis:
The proposed sintering process produce porosity and functional graded microstructure in the sinterd titanium powders. Titanium powders with different micro sizes were sintered at the proposed temperature region at 1200 and 1300°C for 2h. The apatite-forming on the graded microstructure is observed by immersion test in Hanks balanced salt soluion at 37°C. Sintering condition of titanium powders is estimated by thermogravitmetry-differential thermal analysis (TG-DTA). The synthersied surface structures and apatite-forming ability were characterized by a field emission scanning electron microscopy (FE-SEM) observation and energy dispersive X-ray spectroscopy (EDS) analysis. As results, these graded microstructure of sintered porous titanium powders reveals apatite-forming ability as osseointegration by calcification in Hanks balanced salt soluion(HBSS) at 37°C.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1265-1269
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis And Electrochemical Characteristics Of Mechanically Alloyed Anode Materials SnS2 For Li/SnS2 Cells
Synteza mechaniczna i charakterystyka elektrochemiczna materiałów anodowych SnS2 dla ogniw Li/SnS2
Autorzy:
Hong, J. H.
Liu, X. J.
Park, D. K.
Kim, K. W.
Ahn, H. J.
Ahn, I. S.
Powiązania:
https://bibliotekanauki.pl/articles/356903.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
MA
Li/SnS2 cell
PCA
wet milling process and electrochemical characteristics
ogniwa Li/SnS2
charakterystyka elektromechaniczna
Opis:
With the increasing demand for efficient and economic energy storage, tin disulfide (SnS2), as one of the most attractive anode candidates for the next generation high-energy rechargeable Li-ion battery, have been paid more and more attention because of its high theoretical energy density and cost effectiveness. In this study, a new, simple and effective process, mechanical alloying (MA), has been developed for preparing fine anode material tin disulfides, in which ammonium chloride (AC), referred to as process control agents (PCAs), were used to prevent excessive cold-welding and accelerate the synthesis rates to some extent. Meanwhile, in order to decrease the mean size of SnS2 powder particles and improve the contact areas between the active materials, wet milling process was also conducted with normal hexane (NH) as a solvent PCA. The prepared powders were both characterized by X-ray diffraction, Field emission-scanning electron microscopeand particle size analyzer. Finally, electrochemical measurements for Li/SnS2 cells were takenat room temperature, using a two-electrode cell assembled in an argon-filled glove box and the electrolyte of 1M LiPF6 in a mixture of ethylene carbonate(EC)/dimethylcarbonate (DMC)/ethylene methyl carbonate (EMC) (volume ratio of 1:1:1).
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1191-1194
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Electroless Ni–P Plating on the Bonding Strength of Bi–Te-Based Thermoelectric Modules
Autorzy:
Kim, S. S.
Son, I.
Kim, K. T.
Powiązania:
https://bibliotekanauki.pl/articles/356583.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
thermoelectric
Ni–P plating
bonding strength
Bi–Te
soldering
Opis:
In the present study, electroless Ni–P plating was applied to Bi–Te-based thermoelectric materials as a barrier layer and the effect of the Ni–P plating on the bonding strength of the thermoelectric module was investigated. The bonding strength of the n- and p-type modules increased after being subjected to the electroless Ni–P plating treatment. In the case of the thermoelectric module that was not subjected to electroless Ni–P plating, Sn and Te were interdiffused and formed a brittle Sn–Te-based metallic compound. The shearing mostly occurred on the bonding interface where such an intermetallic compound was formed. On the other hands, it was found from the FE-EPMA analysis of the bonding interface of thermoelectric module subjected to electroless Ni-P plating that the electroless Ni-P plating acted as an anti-diffusion layer, preventing the interdiffusion of Sn and Te. Therefore, by forming such an anti-diffusion layer on the surface of the Bi–Te based thermoelectric element, the bonding strength of the thermoelectric module could be increased.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1225-1229
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Surface Characterization of Metallic Fuel Slugs Prepared by Modified Injection Casting
Autorzy:
Mun, S.-U.
Kim, K.-H.
Oh, S.-J.
Park, J.-Y.
Hong, S.-I.
Powiązania:
https://bibliotekanauki.pl/articles/351428.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
sodium-cooled fast reactor
metallic fuel slug
U-Zr alloy
surface characterization
injection casting
Opis:
Metallic fuel slugs containing rare-earth (RE) elements have high reactivity with quartz (SiO2) molds, and a reaction layer with a considerable thickness is formed at the surface of metallic fuel slugs. The surface characterization of metallic fuel slugs is essential for safety while operating a fast reactor at elevated temperature. Hence, it is necessary to evaluate the surface characteristics of the fuel slugs so that chemical interaction between fuel slug and cladding can be minimized in the reactor. When the Si element causes a eutectic reaction with the cladding, it deteriorates the metallic fuel slugs. Thus, it is necessary to examine the characteristics of the surface reaction layer to prevent the reaction of the metallic fuel slugs. In this study, we investigated the metallurgical characteristics of the surface reaction layer of fabricated U-10wt.%Zr-Xwt.%RE (X = 0, 5, 10) fuel slugs using injection casting. The results showed that the thickness of the surface reaction layer increased as the RE content of the metallic fuel slugs increased. The surface reaction layer of the metallic fuel slug was mainly formed by RE, Zr and the Si, which diffused in the quartz mold.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1049-1053
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A study of the local entropy generation rate in a porous media burner
Autorzy:
Mohammadi, I.
Esfahani, J. A.
Kim, K. C.
Powiązania:
https://bibliotekanauki.pl/articles/38597672.pdf
Data publikacji:
2020
Wydawca:
Instytut Podstawowych Problemów Techniki PAN
Tematy:
porous media burner
chemical kinetics
volumetric heat transfer
axisymmetric combustion
local entropy generation
excess air ratio
Opis:
In this paper, the work and performance of the premixed methane-air porous axisymmetrical burner have firstly been simulated numerically using the CFD tools. For this purpose the set of governing equations has been enriched by an additional energy equation in porous solid, and the chemical species transport has been extended onto the multi-step mechanism (GRI-2-11). This numerical model has been verified on the base of available benchmark experiments. Next, we have studied the local entropy generation problem taking into account not only classical contributions like viscous and turbulent dissipation but also, the porous combustion of gases. The results showed that the greatest portion of entropy generation in the porous medium burner is related to chemical reactions, followed by heat transfer, mass diffusion (mixing) and friction (viscous dissipation), respectively. According to the results, as the excess air ratio increases, the local entropy generation rate due to heat transfer and friction increases and the local entropy generation rate due to chemical reactions is decreased. Also, by increasing the volumetric heat transfer coefficient, the local entropy generation rate due to heat transfer decreases and the local entropy generation rate due to friction and chemical reactions increases. Also, the local entropy generation rate due to mixing does not show a significant change with the changing excess air ratio and volumetric heat transfer coefficient.
Źródło:
Archives of Mechanics; 2020, 72, 3; 257-279
0373-2029
Pojawia się w:
Archives of Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Similarity of chromosome structure among Populus tremula var. davidiana, Populus alba and their hybrids revealed by FISH karyotype analysis
Autorzy:
Kim, Y.G.
Kwon, S.H.
Kang, H.I.
Yoem, D.B.
Kim, K.W.
Kim, H.H.
Kang, K.S.
Powiązania:
https://bibliotekanauki.pl/articles/2077655.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Instytut Dendrologii PAN
Tematy:
Karyotype analysis
Fluorescence in situ hybridization
Ribosomal DNA site
Poplar
Cytogenetics
Opis:
The genus Populus is one of the important tree species in Korean peninsula and many other coun- tries in the world. It represents the model species of forest genomics because it grows fast and reproduces rapidly. In this reason, their genetic characteristics have been well studied and the whole genome has been sequenced completely in some species. However, cytogenetic study of the genus Populus has been limited. In the present study, karyotypes of Korean aspen (P. tremula var. davidiana), Silver poplar (P. alba) and their two hybrids, Suwon aspen (P. tremula var. glandulosa) and Hyun aspen (P. alba × P. tremula var. glandulsa) were analyzed by means of the fluorescence in situ hybridization (FISH). Root samples were collected from mature trees in the demonstration forest, located at Suwon, Kyonggi province in South Korea. The fresh root cells were examined by DAPI (4’,6-diamidino-2-phenylindole) staining and FISH using 45S rDNA and 5S rDNA probes. As the results, the chromosome compositions of all species were the same as 2n = 38. The karyotype formulas of Korean aspen, Silver poplar, Suwon aspen and Hyun aspen were 28m + 6sm + 4st (2sat), 26m + 10sm (2sat) + 2st, 26m + 12sm (2sat) and 28m + 10sm (2sat), respectively. The four species had one pair of 45S rDNA site and one pair of 5S rDNA site in common with FISH karyotypes. The similarity of FISH karyotypes among four species indicated close genetic relationship and coexistence of their interspecific hybrids. This research will provide genetic information on cytogenetic research of Populus and genetic mapping that can be applied to the breeding program of Populus in the near future.
Źródło:
Dendrobiology; 2020, 83; 68-74
1641-1307
Pojawia się w:
Dendrobiology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Morphology of strobili at different development positions and cone and seed characteristics of Pinus densiflora f. multicaulis
Autorzy:
Kwon, S.H.
Kim, Y.G.
Kang, H.I.
Shim, D.
Kang, K.S.
Powiązania:
https://bibliotekanauki.pl/articles/2078259.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Instytut Dendrologii PAN
Tematy:
bisexual strobili
sex reversal
microsporangia
megasporangia
cone analysis
Opis:
Pinus densiflora f. multicaulis is a rare and unusual form of genus Pinus. It has excellent ornamen- tal values due to many trunks from its root collar, and produces female, male, and bisexual strobili on the same tree. However, there is limited study whether the bisexual strobili are functional, mature lateral cones produce filled seeds, and the seeds from the mature lateral cones germinate and grow as well as those from mature apical cones. The structure of apical female, and lateral male and bisexual strobili were analyzed in an open-pollination-progeny population. The strobili were photographed to obtain external, cross-section, and radial-section images using a 45× stereoscopic microscope. Radial sections of strobili were imaged using scanning electron microscopy. Characteristics of apical and lateral cones and seeds were surveyed by cone analysis and germination test. P. densiflora f. multicaulis developed typical female strobili apically, and ordinary male and bisexual strobili laterally. Additionally, female strobili developed laterally whereas the male strobili were normally located. The mature lateral female strobili had the same structure as the apical female. In the mature bisexual strobili, the proportion of male and female tissue was unequal. The cones developed from lateral female strobili showed highly significant differences in the length, width, and weight, being shorter (32.7%), narrower (26.9%), and lighter (59.8%) than those from apical female strobili. Both types produced filled seeds and seedlings, and well significant positive correlations were found among characteristics of seeds from apical and lateral female strobili. The initial seed germination rate of the seeds from apical female strobili was higher than that of seeds from lateral female strobili, but the difference decreased over time. The viability and spatial distribution of the female and male tissue of bisporangiate cones, and their frequent occurrence suggests a common mechanism for the production of bisporangiate structures in seed plants.
Źródło:
Dendrobiology; 2021, 85; 51-59
1641-1307
Pojawia się w:
Dendrobiology
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-13 z 13

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies